Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Finite element model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

System Identification of Damped Truss-Like Space Structures

A spacecraft payload flown on a launch vehicle experiences dynamic loads. The dynamic loads are caused by various phenomena ranging from the start-up of the launch vehicle engine to wind gusts. A spacecraft payload should be designed to meet launch vehicle dynamic loads. One of the major steps taken towards determining the dynamic loads is to correlate the finite element model of the spacecraft with the test results of a modal survey test. A test-verified finite element model of the spacecraft should possess the same spatial properties (stiffness, mass, and damping) and modal properties (frequencies and mode shapes) as the test hardware representing the spacecraft. The test-verified and correlated finite element model of the spacecraft is then coupled with the finite element model of the launch vehicle for analysis of loads and stress. Modal survey testing, verification of a finite element model, and modification of the finite element model to match the modal survey test results can easily be accomplished if the spacecraft structure is simple. However, this is rarely the case. A simple structure here is defined as a structure where the influence of nonlinearity between force and displacement (uncertainty in a test, for example, with errors in input and output), and the influence of damping (structural, coulomb, and viscous) are not pronounced. The objective of this study is to develop system identification and correlation methods with the focus on the structural systems that possess nonproportional damping. Two approaches to correct the nonproportional damping matrix of a truss structure were studied, and have been implemented on truss-like structures such as the National Aeronautics and Space Administration's space station truss. The results of this study showed nearly 100 percent improvement of the correlated eigensystem over the analytical eigensystem. The first method showed excellent results with up to three modes used in the system identification process. The second method could handle more modes, but required more computer usage time, and the results were less accurate than those of the first method.

Armand, Sasan↗
NASA NTRS2021

Analysis of Arc Welding Process in Space

This work is motivated by NASA plans to conduct welding experiments on the ISS. It is expected that deployment of welding and additive manufacturing technologies in the space environment has the potential to revolutionise how orbiting platforms are designed, manufactured, and assembled. However, the structure, composition and quality of a weld is extremely dependent on the environment and can be difficult to control in space. Shielding gases would also be tough to manage as gases behave differently in zero gravity and airless environments. Additional points of concern are related to the spatter and sparks dynamics in space. Therefore, there is a need for a more basic understanding of welding processes by computational modelling. To provide such an insight we developed state of art models of the ARC torch, droplet detachment and transfer, and the melt pool build up using magnetohydrodynamics approximation and level set method for two-phase liquid metal/-gas flow modelling. Two finite element models were built using 2D axisymmetric geometry in COMSOL Multiphysics®: (i) stationary model of the ARC torch and (ii) dynamical model of droplet detachment and transfer. Both models demonstrate reasonable agreement with earlier experimental observations and high sensitivity to the temperature dependence of the thermophysical parameters on the system materials. The models were used to provide physical insight into ARC welding in various environments and geometries. It was shown, in particular, that there is a significant probability of gas bubbles trapping in the meltpool and a possibility of unbounded wondering of sparks in the welding chamber in zero gravity. In addition, we estimated metal evaporation rate that may be hazardous in the confined environment of the ISS. These issues raise concern of quality of the weld and safety for ISS applications.

ARC welding↗
DOE OSTI2022

A crystal plasticity finite element method modeling of Zircaloy with hydride phases based on scanning electron micrographs

This work developed a microstructure-based finite element model to predict the stress state of alloys with second phase inclusions. Quantitative microstructural details extracted from scanning electron microscopy (SEM) images were used to generate heterogeneous microstructures including the morphology and spatial distribution of hydrides. Generation of digital microstructure was achieved through two steps of tessellations using software Neper and Matlab. The process is demonstrated using an example of Zircaloy material with secondary phases of hydrides dispersed within and stress-strain response of Zircaloy containing hydrides was predicted. The constitutive material model for Zircaloy in this study was based on crystal plasticity theory which considers the hexagonal close-packed (HCP) atomic structure of Zircaloy material. The hydrides were modeled as isotropic elasto-plastic material. A parametric study had been conducted to understand the effect of volume fraction, and lamellae thickness of the hydride phase on the mechanical properties of the overall material. Results can help designers to alter the manufacturing process to obtain the enhanced mechanical properties for components used in nuclear applications made by Zircaloy material.

Kulkarni, Shank S.↗
NASA NTRS2021

Operational Modal Analysis of the Space Launch System Mobile Launcher on the Crawler Transporter ISVV-010 Rollout

NASA is developing an expendable heavy lift launch vehicle capability, the Space Launch System, to support lunar and deep space exploration. To support this capability, an updated ground infrastructure is required including modifying an existing Mobile Launcher system. The Mobile Launcher is a very large heavy beam/truss steel structure designed to support the Space Launch System during its buildup and integration in the Vehicle Assembly Building, transportation between the Vehicle Assembly Building and launch pad 39B by the Crawler Transporter, and provides the launch platform at the launch pad. As part of the Verification and Validation of the Mobile Launcher and Crawler Transporter, two rollouts of the Mobile Launcher transported by the Crawler Transporter, Integrated System Verification and Validation (ISVV) 005 and 010, have been performed to demonstrate the Crawler Transporter’s ability to transport the Mobile Launcher. ISVV-005 occurred in September 2018 and ISVV-010 occurred in late June 2019. ISVV-005 and ISVV-010 also provided the opportunity to gather data that can be used identify the Mobile Launcher on the Crawler Transporter rollout modal characteristics and refine the estimates of the Artemis I integrated launch vehicle rollout forcing functions. While the rollout environment has historically produced relatively small launch vehicle structural loads for the Saturn/Apollo and Space Shuttle programs in comparison to launch and ascent loads, these relatively small structural loads are inputs to structural fatigue analyses. The same holds true for the Space Launch System. Because the rollout forces acting on the Mobile Launcher and the Crawler Transporter are not directly measurable, Operational Modal Analysis techniques, instead of traditional Experimental Modal Analysis techniques, provide an empirical means to identify the Mobile Launcher on the Crawler Transporter rollout modal characteristics. The ISVV-010 rollout modal characteristics provide important supplemental modal information, which along with the Mobile Launcher modal test that was performed in June 2019 immediately prior to ISVV-010 rollout, combine to reduce uncertainty in the test correlated Mobile Launcher on the Crawler Transporter finite element model. A well test correlated finite element model will play a key role in the Building Block approach the Space Launch System program has implemented as part of its certification process for the Artemis I flight and in refining the Artemis I rollout forcing functions. At the time of the ISVV-005 rollout in September 2018, the Mobile Launcher was still undergoing construction, and therefore its modal characteristics are not directly comparable to those of the Mobile Launcher during the June 2019 Mobile Launcher modal test and subsequent ISVV-010 rollout. Hence the ISVV-005 rollout modal characteristics will not be looked at in this paper. This paper will briefly describe the Mobile Launcher and Crawler Transporter physical characteristics, ISVV-010 rollout data collection, the challenges in implementing Operational Modal Analysis techniques due in part to the Crawler Transporter harmonics, and how these challenges were overcome to obtain the ISVV-010 Mobile Launcher on the Crawler Transporter rollout modal characteristics.

Apollo↗
NASA NTRS1980

Finite element structural model of a large, thin, completely free, flat plate

A finite element structural model of a 30.48 m x 30.48 m x 2.54 mm completely free aluminum plate is described and modal frequencies and mode shape data for the first 44 modes are presented. An explanation of the procedure for using the data is also presented. The model should prove useful for the investigation of controller design approaches for large flexible space structures.

Joshi, S. M.↗
NASA NTRS2011

Seal Joint Analysis and Design for the Ares-I Upper Stage LOX Tank

The sealing capability of the Ares-I Upper Stage liquid oxygen tank-to-sump joint is assessed by analyzing the deflections of the joint components. Analyses are performed using three-dimensional symmetric wedge finite element models and the ABAQUS commercial finite element software. For the pressure loads and feedline interface loads, the analyses employ a mixed factor of safety approach to comply with the Constellation Program factor of safety requirements. Naflex pressure-assisted seals are considered first because they have been used successfully in similar seal joints in the Space Shuttle External Tank. For the baseline sump seal joint configuration with a Naflex seal, the predicted joint opening greatly exceeds the seal design specification. Three redesign options of the joint that maintain the use of a Naflex seal are studied. The joint openings for the redesigned seal joints show improvement over the baseline configuration; however, these joint openings still exceed the seal design specification. RACO pressure-assisted seals are considered next because they are known to also be used on the Space Shuttle External Tank, and the joint opening allowable is much larger than the specification for the Naflex seals. The finite element models for the RACO seal analyses are created by modifying the models that were used for the Naflex seal analyses. The analyses show that the RACO seal may provide sufficient sealing capability for the sump seal joint. The results provide reasonable data to recommend the design change and plan a testing program to determine the capability of RACO seals in the Ares-I Upper Stage liquid oxygen tank sump seal joint.

Phillips, Dawn R.↗
NASA NTRS1993

Effective thermoelastic and thermal properties of unidirectional fiber-reinforced composites and their sensitivity coefficients

Three-dimensional finite element models are used to assess the accuracy of the thermoelastic and thermal properties of unidirectional fiber-reinforced composites predicted by six different micromechanical models. The six models are: simple mechanics of materials type equations, fiber substructuring model, vanishing fiber diameter model, self-consistent model, Mori-Tanaka model, and method of cells. In addition, the finite element models are used to assess the accuracy of derivatives of the effective properties, with respect to each of the constituent material properties and fiber-volume ratio, computed using the six micromechanical models. The predictions of the micromechanical and finite element models for four advanced composite material systems are compared with experimental data. The results obtained in the present study show that the predictions of the Mori-Tanaka model and the method of cells are closer to those of the finite element models than those of all the other micromechanical models.

Noor, Ahmed K.↗
NASA NTRS1999

Neural Networks Used to Compare Designed and Measured Time-Average Patterns

Electronic time-average holograms are convenient for comparing the measured vibration modes of fan blades with those calculated by finite-element models. At the NASA Lewis Research Center, neural networks recently were trained to perform what had been a simple visual comparison of the predictions of the design models with the measurements. Finite-element models were used to train neural networks to recognize damage and strain information encoded in subtle changes in the time-average patterns of cantilevers. But the design-grade finite element models were unable to train the neural networks to detect damage in complex blade shapes. The design-model-generated patterns simply did not agree well enough with the measured patterns. Instead, hybrid-training records, with measured time-average patterns as the input and model-generated strain information as the output, were used to effect successful training.

Decker, Arthur J.↗
NASA NTRS1991

A comparison of classical mechanics models and finite element simulation of elastically tailored wing boxes

Structural tailoring concepts were developed to create wings with elastically produced camber for the purpose of increasing lift during takeoff conditions. Simple models based upon enhancements to the thin walled composite beam theory of Rehfield were developed to investigate prospects for elastic tailoring of the chordwise deformation of wing structures. The purpose here is to provide a comparison of the theoretical results with a finite element model for the bending method of producing camber. Finite element correlation studies were completed for two cases: a bonded unstiffened structural box, and a bolted unstiffened structural box. Results from these studies show an error of less than one percent for the bonded case and less than six percent for the bolted case in predicting camber curvature for the structural box. Examination of the results shows that the theory is very accurate for the cases studied and will provide an excellent basis for conducting further tailoring studies.

Rehfield, Lawrence W.↗
NASA NTRS1994

Dynamic analysis of Space Shuttle/RMS configuration using continuum approach

The initial assembly of Space Station Freedom involves the Space Shuttle, its Remote Manipulation System (RMS) and the evolving Space Station Freedom. The dynamics of this coupled system involves both the structural and the control system dynamics of each of these components. The modeling and analysis of such an assembly is made even more formidable by kinematic and joint nonlinearities. The current practice of modeling such flexible structures is to use finite element modeling in which the mass and interior dynamics is ignored between thousands of nodes, for each major component. The model characteristics of only tens of modes are kept out of thousands which are calculated. The components are then connected by approximating the boundary conditions and inserting the control system dynamics. In this paper continuum models are used instead of finite element models because of the improved accuracy, reduced number of model parameters, the avoidance of model order reduction, and the ability to represent the structural and control system dynamics in the same system of equations. Dynamic analysis of linear versions of the model is performed and compared with finite element model results. Additionally, the transfer matrix to continuum modeling is presented.

Ramakrishnan, Jayant↗
NASA NTRS1974

Development of technology for modeling of a 1/8-scale dynamic model of the shuttle Solid Rocket Booster (SRB)

A NASTRAN analysis of the solid rocket booster (SRB) substructure of the space shuttle 1/8-scale structural dynamics model. The NASTRAN finite element modeling capability was first used to formulate a model of a cylinder 10 in. radius by a 200 in. length to investigate the accuracy and adequacy of the proposed grid point spacing. Results were compared with a shell analysis and demonstrated relatively accurate results for NASTRAN for the lower modes, which were of primary interest. A finite element model of the full SRB was then formed using CQUAD2 plate elements containing membrane and bending stiffness and CBAR offset bar elements to represent the longerons and frames. Three layers of three-dimensional CHEXAI elements were used to model the propellant. This model, consisting of 4000 degrees of freedom (DOF) initially, was reduced to 176 DOF using Guyan reduction. The model was then submitted for complex Eigenvalue analysis. After experiencing considerable difficulty with attempts to run the complete model, it was split into two substructres. These were run separately and combined into a single 116 degree of freedom A set which was successfully run. Results are reported.

Levy, A.↗
NASA NTRS2010

Modification of a Macromechanical Finite-Element Based Model for Impact Analysis of Triaxially-Braided Composites

A macro level finite element-based model has been developed to simulate the mechanical and impact response of triaxially-braided polymer matrix composites. In the analytical model, the triaxial braid architecture is simulated by using four parallel shell elements, each of which is modeled as a laminated composite. For the current analytical approach, each shell element is considered to be a smeared homogeneous material. The commercial transient dynamic finite element code LS-DYNA is used to conduct the simulations, and a continuum damage mechanics model internal to LS-DYNA is used as the material constitutive model. The constitutive model requires stiffness and strength properties of an equivalent unidirectional composite. Simplified micromechanics methods are used to determine the equivalent stiffness properties, and results from coupon level tests on the braided composite are utilized to back out the required strength properties. Simulations of quasi-static coupon tests of several representative braided composites are conducted to demonstrate the correlation of the model. Impact simulations of a represented braided composites are conducted to demonstrate the capability of the model to predict the penetration velocity and damage patterns obtained experimentally.

Goldberg, Robert K.↗
NASA NTRS1994

Influence of backup bearings and support structure dynamics on the behavior of rotors with active supports

Progress over the past year includes the following: A simplified rotor model with a flexible shaft and backup bearings has been developed. A simple rotor model which includes a flexible disk and bearings with clearance has been developed and the dynamics of the model investigated. A rotor model based upon the T-501 engine has been developed which includes backup bearing effects. Parallel simulation runs are being conducted using an ANSYS based finite element model of the T-501. The magnetic bearing test rig is currently floating and dynamics/control tests are being conducted. A paper has been written that documents the work using the T-501 engine model. Work has continued with the simplified model. The finite element model is currently being modified to include the effects of foundation dynamics. A literature search for material on foil bearings has been conducted. A finite element model is being developed for a magnetic bearing in series with a foil backup bearing.

Flowers, George T.↗
NASA NTRS2019

Aero-Structural Modeling of the Truss-Braced Wing Aircraft Using Potential Method with Correction Methods for Transonic Viscous Flow and Wing-Strut Interference Aerodynamics

This paper describes an aero-structural modeling method for the Transonic Truss-Braced Wing (TTBW) aircraft using VSPAERO. A vortex-lattice model of the TTBW aircraft is developed, and a transonic and viscous flow correction method is implemented in the VSPAERO models to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which cause a deflection dependent nonlinear stiffness. The VSPAERO models are coupled to the finite-element model to provide a rapid capability for aero-structural modeling and flutter analysis. A flight-optimized jig twist model is being developed and will be applied for the purpose of generating a full flight dynamic model of the TTBW aircraft.

Fugate, Jason↗
DOE OSTI2020

Thermal Model Heat Rate Predictions of the AGR-5/6/7 Experiment

Several fuel and material irradiation experiments have been planned for the U.S. Department of Energy Advanced Gas Reactor Fuel Development and Qualification Program, which supports the development and qualification of tristructural isotropic (TRISO) coated particle fuel for use in high-temperature gas-cooled reactors. The goals of these experiments are to provide irradiation performance data to support fuel process development, qualify fuel for normal operating conditions, support development of fuel performance models and codes, and provide irradiated fuel and materials for post-irradiation examination and safety testing. Originally planned and named as separate fuel experiments, but subsequently combined into a single test train. AGR-5/6/7 will test low-enriched uranium oxycarbide (UCO – a heterogeneous mixture of uranium oxide and uranium carbide) TRISO fuel. The AGR-5/6 portion of the experiment will provide data to support qualification of the selected reference fuel design, while the AGR-7 portion will serve as a margin test, irradiating the fuel beyond normal operating conditions. During irradiation, the temperature in each capsule is controlled by varying the helium / neon gas mixture flowing through the capsule until the desired thermocouple temperature is reached. Further adjustments can be made by changing the lobe power and the neutron filter. Three neutron filters are available to use as the experiment burns up the fissionable fuel. A thermal finite element model has been created for the five capsules comprising the AGR-5/6/7 experiment. Heat rates from a physics analysis are imported into the model along with fast neutron fluence. Graphite shrinkage due to the fast neutron fluence is incorporated into the model. Gas gaps change as a function of fast neutron fluence. Radiation heat transfer is a major contributor in this model. This is a large model with more than 1 million finite element brick elements. More than 150 different parts are modeled in the finite element model and communicate with each other from a heat transfer sense. More than 50 thermocouples are used in the experiment and are compared to actual measurements. The experiment is composed of five separate stainless steel capsules all welded together. This paper presents a method used to predict the gas mixture in the event that all of the thermocouples fail in a particular capsule. Curve fitting of heat rates from previous cycles and projecting them into the future is the basis of the method.

36 MATERIALS SCIENCE↗
NASA NTRS1988

Fiber Composite Sandwich Thermostructural Behavior - Computational Simulation

Four computational simulation methods with different levels of sophistication were used to simulate thermal behavior and structural changes of composite sandwich panels with a honeycomb core subjected to a variety of environmental effects. The models on thich these methods are based include three-dimensional finite-element modeling, three-dimensional finite-element modeling assuming a homogeneous core, laminate theory, and simple equations for predicting the equivalent properties of the honeycomb core. A procedure was developed and embedded in a composite mechanics computer code, which made it possile to conduct parametric studies to determine 'optimum' composite sandwich configurations for specific applications. The procedure was applied for the evaluation of composite sandwich behavior at the global, local, laminate, ply, and micromechanics levels when the composite sandwich is subjected to hygral, thermal, and mechanical loading environments.

Chamis, Christos C.↗
NASA NTRS2020

Jig Twist Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft and High-Fidelity CFD Validation

This paper presents a jig twist optimization study of Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft using an in-house developed aero-structural analysis solver VSPAERO coupled to BEAM3D. A vortex-lattice model of the TTBW model is developed, and a transonic and viscous flow correction method is implemented in the VSPAERO model to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which causes a deflection-dependent nonlinear stiffness. The VSPAERO model is coupled to the corresponding finite-element model to provide a rapid aero-structural analysis. A design flight condition corresponding to Mach 0.745 at 42000 ft is selected for the TTBW aircraft jig twist optimization to reduce the drag coefficient. After the design is implemented, the drag coefficient of the twist optimized TTBW aircraft is reduced about 8 counts. At the end, a high-fidelity CFD solver FUN3D is used to validate the design.

BEAM3D↗
NASA NTRS2020

Jig Twist Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft and High-Fidelity CFD Validation

This paper presents a jig twist optimization study of Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft using an in-house developed aero-structural analysis solver VSPAERO coupled to BEAM3D. A vortex-lattice model of the TTBW model is developed, and a transonic and viscous flow correction method is implemented in the VSPAERO model to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which causes a deflection-dependent nonlinear stiffness. The VSPAERO model is coupled to the corresponding finite-element model to provide a rapid aero-structural analysis. A flight condition corresponding to Mach 0.745 at 42000 ft is selected for the TTBW aircraft jig twist optimization to reduce the drag coefficient. After the design is implemented, the drag coefficient of the twist optimized TTBW aircraft is reduced about 8 counts. At the end, a high-fidelity CFD solver FUN3D is used to validate the design.

Xiong, Juntao↗