SEARCH · Engineering Papers

Results for “Fiber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

DOE OSTI2019

Spatial Heterodyne Raman Spectrometer (SHRS) for In Situ Chemical Sensing Using Sapphire and Silica Optical Fiber Raman Probes

A spatial heterodyne Raman spectrometer (SHRS), constructed using a modular optical cage and lens tube system, is described for use with a commercial silica and a custom single-crystal (SC) sapphire fiber Raman probe. The utility of these fiber-coupled SHRS chemical sensors is demonstrated using 532 nm laser excitation for acquiring Raman measurements of solid (sulfur) and liquid (cyclohexane) Raman standards as well as real-world, plastic-bonded explosives (PBX) comprising 1,3,5- triamino- 2,4,6- trinitrobenzene (TATB) and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) energetic materials. The SHRS is a fixed grating-based dispersive interferometer equipped with an array detector. Each Raman spectrum was extracted from its corresponding fringe image (i.e., interferogram) using a Fourier transform method. Raman measurements were acquired with the SHRS Littrow wavelength set at the laser excitation wavelength over a spectral range of ∼1750 cm −1 with a spectral resolution of ∼8 cm −1 for sapphire and ∼10 cm −1 for silica fiber probes. The large aperture of the SHRS allows much larger fiber diameters to be used without degrading spectral resolution as demonstrated with the larger sapphire collection fiber diameter (330 μm) compared to the silica fiber (100 μm). Unlike the dual silica fiber Raman probe, the dual sapphire fiber Raman probe did not include filtering at the fiber probe tip nearest the sample. Even so, SC sapphire fiber probe measurements produced less background than silica fibers allowing Raman measurements as close as ∼85 cm −1 to the excitation laser. Despite the short lengths of sapphire fiber used to construct the sapphire probe, well-defined, sharp sapphire Raman bands at 420, 580, and 750 cm −1 were observed in the SHRS spectra of cyclohexane and the highly fluorescent HMX-based PBX. SHRS measurements of the latter produced low background interference in the extracted Raman spectrum because the broad band fluorescence (i.e., a direct current, or DC, component) does not contribute to the interferogram intensity (i.e., the alternating current, or AC, component). SHRS spectral resolution, throughput, and signal-to-noise ratio are also discussed along with the merits of using sapphire Raman bands as internal performance references and as internal wavelength calibration standards in Raman measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Injection Overmolding of Continuous Carbon Fiber Preforms

This project explored and developed a process to injection overmold continuous carbon fiber preforms fabricated with tailored fiber placement. Much early work was focused on the ability to infuse dry carbon fiber tow, fully wetting out the fibers, in an injection molding process. Various approaches were explored, including using commingled fiber and pre-consolidated flexible preforms. The commingled fiber was a blend of carbon fiber and polymer fiber matching the injecting polymer. This approach showed some merit but required an extremely high quality homogeneous mixing of the polymer fibers with the carbon fibers to wet out the carbon fiber tow. Therefore, the project focused on pre-consolidated preforms. The pre-consolidated preform manufacturing method was first developed using compression molded flat plates that were cut into tensile specimen for testing. Work then progressed to an injection molded simplified corner fitting bracket. It was shown that a viable manufacturing method for overmolding continuous carbon fiber preforms could be developed.

36 MATERIALS SCIENCE↗

NASA NTRS2001

Size and myonuclear domains in Rhesus soleus muscle fibers: short-term spaceflight

The cross-sectional area (CSA), myonuclear number per mm of fiber length, and myonuclear domain (cytoplasmic volume/myonucleus) of mechanically isolated single fibers from biopsies of the soleus muscle of 5 vivarium control, 3 flight simulation and 2 flight (BION 11) Rhesus monkeys (Macaca [correction of Macacca] mulatta) were determined using confocal microscopy before and after a 14-day experimental period. Simulation monkeys were confined in chairs placed in capsules identical to those used during the flight. Fibers were classified as type I, type II or hybrid (containing both types I and II) based on myosin heavy chain (MHC) gel electrophoresis. A majority of the fibers sampled contained only type I MHC, i.e. 89, 62 and 68% for the control, simulation and flight groups, respectively. Most of the remaining fibers were hybrids, i.e. 8, 36 and 32% for the same groups. There were no significant pre-post differences in the fiber type composition for any of the experimental groups. There also were no significant pre-post differences in fiber CSA, myonuclear number or myonuclear domain. There was, however, a tendency for the fibers in the post-flight biopsies to have a smaller mean CSA and myonuclear domain (approximately 10%, p=0.07) than the fibers in the pre-flight biopsy. The combined mean cytoplasmic volume/myonucleus for all muscle fiber phenotypes in the Rhesus soleus muscle was approximately 25,000 micrometers3 and there were no differences in pre-post samples for the control and simulated groups. The cytoplasmic domains tended to be lower (p=0.08) after than before flight. No phenotype differences in cytoplasmic domains were observed. These data suggest that after a relatively short period of actual spaceflight, modest fiber atrophy occurs in the soleus muscle fibers without a concomitant change in myonuclear number.

NASA Experiment Number 8808A05↗

DOE OSTI2018

Low Loss Graded Index Polymer Optical Fiber for Local Networking

Here, the objective of this Department of Energy SBIR program has been to develop technology for the advancement of advanced computing systems. NanoSonic worked with two subcontractors, the Polymicro Division of Molex, a U.S.-based manufacturer of specialized optical fiber and fiber components, and Virginia Tech, a research university involved through the Global Environment for Network Innovations (GENI) program in high-speed computer networking research. NanoSonic developed a patented molecular-level self-assembly process to manufacture polymer-based optical fibers in a way similar to the modified chemical vapor deposition (MCVD) approach typically used to make glass optical fibers. Although polymer fiber has a higher attenuation per unit length than glass fiber, short connectorized polymer fiber jumpers offer significant cost savings over their glass counterparts, particularly due to the potential use of low-cost plastic fiber connectors. As part of the SBIR commercialization process, NanoSonic exclusively licensed this technology to a large ($100B+ market cap) U.S.-based manufacturing conglomerate near the end of the first year of the Phase II program. With this base technology developed and licensed, NanoSonic then worked with Polymicro to address secondary program goals of using related but not conflicting production methods to enhance the performance of other specialty optical fiber products and components, and Virginia Tech continued its evaluation of developed polymer fibers in its network infrastructure system on the university campus. We also report our current understanding of the observation during the Phase I program of quantum conductance and partial quantum conductance in metal-insulator-metal (MIM) devices. Such conductance behavior may be modeled as singlemode behavior in one-dimensional electrically conducting waveguides, similar in principle to singlemode optical propagation in dielectric fiber waveguides. Although NanoSonic has not licensed any of the additional technology developed during the second year of the program, several proprietary discussions with major materials companies are underway as of the conclusion of Phase II.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Effects of bridging fibers on the evolution of lamellar architecture during H 2 /H 2 O redox cycling of Fe-foams

Fe/Fe 3 O 4 redox cycling via cyclic H 2 /H 2 O exposure at 800 °C is studied in lamellar Fe foams with 15 vol% fibers, created by freeze-casting. Fibers were integrated in the foams to mitigate densification during cycling by mechanically supporting neighboring lamellae, thus preventing buckling and sintering at contact points. Three fiber types are examined: short (0.1 mm) and long (1–2 mm) stainless-steel fibers, and long zirconia fibers. Long fibers bridge lamellae and have a marked effect on the architecture by increasing the initial interlamellar porosity (from < 60 to > 85%), with a corresponding decrease in foam shrinkage during initial reduction and sintering (from > 80 to < 55% volumetric loss). Though performance improves as compared to fiber-free foams, fiber effectiveness against damage decreases with cycling: after 10 redox cycles, porosity falls from 85 to 50% for foams with long fibers. One novel degradation mechanism is identified: fiber engulfment. This mechanism occurs over successive redox cycles, as material from the lamellae cyclically engulfs (as Fe 3 O 4 ) and withdraws (as Fe) from the fibers, with a net transport from lamellae to fibers after each cycle. Finally, this cyclic coarsening mechanism alters foam architecture from bridged-lamellar (with evenly distributed porosity) to mixed lamellar/fibrous (with unevenly distributed porosity).

36 MATERIALS SCIENCE↗

DOE OSTI2016

Preparation, ferromagnetic and photocatalytic performance of NiO and hollow Co{sub 3}O{sub 4} fibers through centrifugal-spinning technique

Highlights: • NiO and hollow Co{sub 3}O{sub 4} fibers with the diameter of about 10 μm were prepared through centrifugal-spinning technique. • The evolution mechanism from precursor to crystalline fibers was explored. • Both NiO and hollow Co{sub 3}O{sub 4} fibers show ferromagnetism. • The NiO fibers exhibit good photocatalytic performance. - Abstract: Both NiO and hollow Co{sub 3}O{sub 4} fibers with the diameter of about 10 μm have been successfully prepared through spinning high viscous sols into precursor fibers and followed calcination process. The evolution process from precursor to crystalline fibers and the microstructures of the obtained fibers were characterized by TG-DSC, FT-IR, XRD, HRTEM, SEM and the like. The method is facile and cost-effective for mass production of fibers and the obtained fibers are pure phase with high crystallinity. Their magnetic properties were investigated, showing that both the fibers are ferromagnetic. Meanwhile, the NiO fibers exhibit good photocatalytic performance for the removal of Congo red from water under UV light irradiation.

36 MATERIALS SCIENCE↗

DOE OSTI2017

Active and separate secretion of fiber and penton base during the early phase of Ad2 or Ad5 infection

Fiber and penton base overproduced in adenovirus (Ad) infected cells can be secreted prior to progeny release and thereby regulate progeny spread. We aimed to investigate the mechanisms of fiber and penton base secretion in Ad2- or Ad5-infected A549 cells. Our flow cytometry analyses detected abundant surface fiber molecules, but little penton base molecules at 12 h post infection. Immunogold staining combined with transmission electron microscopic analyses revealed separate, non-co-localized release of fiber and penton base in the proximity of the plasma membrane. Depolymerization of microtubule and actin cytoskeletons, and inhibition of Rock kinase and myosin II activity together demonstrated cytoskeletal network-dependent fiber secretion. Inhibition of intracellular calcium [Ca{sup 2+}]{sub i} signaling caused diminished fiber secretion, which was associated with diminished progeny production. Thus, fiber and penton base are actively and separately secreted during the early stages of Ad2 or Ad5 infection, their secretion may play important role in Ad life cycle. - Highlights: •Excessive production of structural proteins is common to viral infection, which may regulate the host-virus equilibrium and the spreading of viruses. •The adenovirus (Ad) structural proteins, fiber and penton base, are respectively important for Ad binding to its receptor and subsequent internalization in host cells. In Ad infected cells, these two structural proteins are excessively produced. •The mechanisms underlying the release of fiber and penton base molecules at the early phase of Ad infection is yet poorly understood. •Our studies show that in Ad5 or Ad2 infected A549 cells, fiber and penton base molecules are actively and separately secreted. •Fiber secretion is dependent on cytoskeleton-mediated protein traffic. •Inhibition of myosin II motor and Ca{sup 2+} signaling activity significantly diminishes fiber secretion. •These findings could contribute to our understanding of Ad spread in human populations.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2016

Bio-composites fabricated by sandwiching sisal fibers with polypropylene (PP)

Sisal fibers reinforced polypropylene (PP) composites were successfully fabricated using sandwiching sisal fibers with PP sheets. The ratio of fiber and polymer matrix was 50:50 (wt. %). Untreated short and long sisal fibers, and alkali treated short sisal fibers in 6% NaOH at 100°C for 1 and 3 h were used as reinforcement or fillers. A small amount (3 wt. %) of maleic anhydride grafted polypropylene (MAPP) was added as a coupling agent. Scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy were used to characterize the surface morphology and chemical composition of the fibers, respectively. Flexural test of sisal/PP composites was done according to ASTM D 790-02. The results showed that flexural strength of untreated long fiber reinforced composite is much higher than that of the untreated and alkali treated short fibers reinforced composites with and without the addition of MAPP. Alkalization related to fiber surface modification, fiber length/fiber orientation and a composite fabrication technique are important factors in contributing to the fiber distribution within the matrix, the bonding between the fiber and the matrix and the enhancement of flexural strength of the bio-composite.

36 MATERIALS SCIENCE↗

DOE OSTI2016

Effects of heat treatment on the mechanical properties of kenaf fiber

Natural fibers are utilized in various ways. One specific application of it, is in the field natural fiber composite (NFC). Considerable amount of researches are conducted in this field due to rising concerns in the harmful effects of synthetic materials to the environment. Additionally, these researches are done in order to overcome the drawbacks which limit the wide use of natural fiber. A way to improve NFC is to look into the reinforcing component (natural fiber). Treatments, which are classified as mechanical or chemical in nature, can be done in order to improve the performance of the natural fiber. The aim of this study is to assess the effects of heat treatment in the mechanical properties of kenaf fiber. In addition, the response of mechanical properties after exposure to high moisture environment of heat-treated kenaf fibers was observed. Heat treatment was done for one hour with the following heating temperatures: 140, 160, 180, and 200 °C. X-ray diffraction analysis was done to calculate the crystallinity index of kenaf fibers after heat treatment. The results showed that increase in tensile strength can be attained when kenaf fibers are heat treated at 140 °C. However, the tensile modulus showed inconsistency with respect to heat treatment temperature. The computed crystallinity index of the fiber matched the tensile strength observed in non-treated and heat-treated kenaf fibers. The results obtained in this study can be used for applications where heat treatment on kenaf fibers is needed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS2018

Exploration of Double Clad Fibers for Increased Stability of Bidirectional Free Space Optical Links

Bidirectional, high data rate, low size, weight, and power (SWaP), and low cost free space optical links are needed for space communication applications to send and receive large volumes of data. We are exploring design strategies for optical transceivers to reduce SWaP and cost through increased misalignment tolerance (pointing requirement reduction) and sharing the optical transmit and receive paths (imposing optical symmetry). In applications where the detector is fiber coupled, the fiber numerical aperture is the main driver of the pointing accuracy requirement. Unfortunately, reducing the pointing requirement by increasing the fiber numerical aperture symmetrically causes instability in received power over small environmental changes. This paper explores double clad fibers as a solution to both reduce the power instability and increase the pointing accuracy tolerance. Double clad fibers can transmit a Gaussian beam from a single mode fiber and receive in a multi-mode aperture. Results show that double clad fiber have an improved misalignment tolerance and a higher stability for small changes in temperature when compared to single mode fibers and multimode fibers. Also, double clad fibers are shown to match the performance of an asymmetrical link design with a single mode transmit fiber and a multimode receive fiber.

Double Clad fibers↗

NASA NTRS2018

Exploration of Double Clad Fibers for Increased Stability of Bidirectional Free Space Optical Links

Double Clad fibers↗

DOE OSTI2024

Emerging continuous SiC fibers for high-temperature applications

Silicon carbide (SiC) fibers are responsible for the ultimate strength and toughness of SiC-fiber reinforced composites in harsh environments. The development of a new generation of continuous SiC fibers continues to advance the mechanical properties of composite materials. Tyranno™ SA4 fiber was recently released as a successor of Tyranno™ SA3 fiber. Laser-driven chemical vapor deposition (LCVD) has been adopted as an alternative fiber processing route to synthesizing high-strength SiC fiber with tailorable small diameters and chemical compositions. Both Tyranno™ SA4 and laser-driven CVD fibers show very high tensile strength, about 4 GPa in the as-fabricated condition. The degradation of thermal stability and strength due to annealing in an inert environment were similar for Tyranno™ SA3 and SA4 fibers because of their similar carbon-rich, crystalline microstructure. Silicon-rich fibers produced by LCVD possessed heterogeneous crystallinity, which was attributed to laser power distribution and showed microstructural instability at 1500 °C and above. Finally, the new SiC fibers demonstrated an increase in as-fabricated strength but faced the same challenges in environmental resistance as the traditional SiC fibers do.

36 MATERIALS SCIENCE↗

DOE OSTI2014

Designing the Structure of Carbon Fibers for Optimal Mechanical Properties

Carbon fiber manufacturing follows generic processing steps: formation of thermoplastic fibers, stabilization, and carbonization. The final structures and end properties of the carbon fiber can differ significantly depending on the precursor chemistry and the associated processing sciences. Polyacrylonitrile (PAN) and mesophase pitch are the predominant precursors used in the production of carbon fibers. PAN-based carbon fibers consist of nanocrystalline graphitic domains typically 1.5 5 nm in size surrounded by amorphous carbon; in contrast, pitch-based carbon fibers are 10 50 nm crystallites with the graphitic (002) planes mostly aligned parallel to the fiber axis. It has been seen that the skin core structure of PAN-based carbon fibers plays a significant role in their mechanical properties. Designing a more homogenous carbon fiber microstructure by controlling the starting polymer and process parameters results in a different set of tensile strengths and elastic moduli. In this study the microstructural defect distribution (0.1 200 nm), measured by small-angle X-ray scattering, was shown to be directly related to the tensile strength of the carbon fibers. Here the formation of carbon structures from various polymer precursors is reviewed. Such a comprehensive understanding offers the opportunity to design carbon fiber microstructures with improved properties and to ultimately create new types of carbon fibers from alternative precursors at reduced cost.

Ozcan, Soydan↗

DOE OSTI2015

The MaNGA integral field unit fiber feed system for the Sloan 2.5 m telescope

We describe the design, manufacture, and performance of bare-fiber integral field units (IFUs) for the SDSS-IV survey Mapping Nearby Galaxies at Apache Point Observatory (MaNGA) on the the Sloan 2.5 m telescope at Apache Point Observatory. MaNGA is a luminosity-selected integral-field spectroscopic survey of 10{sup 4} local galaxies covering 360–1030 nm at R∼2200. The IFUs have hexagonal dense packing of fibers with packing regularity of 3 μm (rms), and throughput of 96 ± 0.5% from 350 nm to 1 μm in the lab. Their sizes range from 19 to 127 fibers (3–7 hexagonal layers) using Polymicro FBP 120:132:150 μm core:clad:buffer fibers to reach a fill fraction of 56%. High throughput (and low focal-ratio degradation (FRD)) is achieved by maintaining the fiber cladding and buffer intact, ensuring excellent surface polish, and applying a multi-layer anti-reflection (AR) coating of the input and output surfaces. In operations on-sky, the IFUs show only an additional 2.3% FRD-related variability in throughput despite repeated mechanical stressing during plate plugging (however other losses are present). The IFUs achieve on-sky throughput 5% above the single-fiber feeds used in SDSS-III/BOSS, attributable to equivalent performance compared to single fibers and additional gains from the AR coating. The manufacturing process is geared toward mass-production of high-multiplex systems. The low-stress process involves a precision ferrule with a hexagonal inner shape designed to lead inserted fibers to settle in a dense hexagonal pattern. The ferrule ID is tapered at progressively shallower angles toward its tip and the final 2 mm are straight and only a few microns larger than necessary to hold the desired number of fibers. Our IFU manufacturing process scales easily to accommodate other fiber sizes and can produce IFUs with substantially larger fiber counts. To assure quality, automated testing in a simple and inexpensive system enables complete characterization of throughput and fiber metrology. Future applications include larger IFUs, higher fill factors with stripped buffer, de-cladding, and lenslet coupling.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2019

Optimized Carbon Fiber Composites in Wind Turbine Blade Design

The objective of this study is to assess the commercial viability to develop cost-competitive carbon fiber composites specifically suited for the unique loading experienced by wind turbine blades. The wind industry is a cost-driven market, while carbon fiber materials have been developed for the performance-driven aerospace industry. Carbon fiber has known benefits for reducing wind turbine blade mass due to the significantly improved stiffness, strength, and fatigue resistance per unit mass compared to fiberglass; however, the high relative cost has prohibited broad adoption within the wind industry. Novel carbon fiber materials derived from the textile industry are studied as a potentially more optimal material for the wind industry and are characterized using a validated material cost model and through mechanical testing. The novel heavy tow textile carbon fiber is compared with commercial carbon fiber and fiberglass materials in representative land-based and offshore reference wind turbine models. Some of the advantages of carbon fiber spar caps are observed in reduced blade mass and improved fatigue life. The heavy tow textile carbon fiber is found to have improved cost performance over the baseline carbon fiber and performed similarly to the commercial carbon fiber in wind turbine blade design, but at a significantly reduced cost. This novel carbon fiber was observed to even outperform fiberglass when comparing material cost estimates for spar caps optimized to satisfy the design constraints. This study reveals a route to enable broader carbon fiber usage by the wind industry to enable larger rotors that capture more energy at a lower cost.

17 WIND ENERGY↗

DOE OSTI2026

Development Fiber Optic Distributed System for Direct Detection of Subsurface Gases Leakages

Carbon, natural gas, and hydrogen gas storage is an emerging solution to safeguard us against pollution, support goals of negative carbon emission, and protect sources of renewable energy. Properly constructed storage wells provide a virtually impervious barrier to any unintended subsurface transmission. The ability to ensure the long-term integrity of such wells is vital to the success of any storage operation and be successful in the public eyes. Therefore, robust monitoring of any gas migration into the subsurface is highly sought. A fiber-optic distributed chemical sensor (DCS) enables monitoring of long-term well integrity along its depth, ensuring the success of any storage operation and bolsters public acceptance of the safety of the reservoir via leak early detection. The same technique can be applied to gas monitoring in pipeline networks and nuclear stockpile monitoring applications. Fiber based Raman spectroscopy enables DCS, as optical fibers can be deployed in virtually any environment and relay spectroscopic information over long distances back to the user. Hollow core fibers (HCF) make excellent DCSs as the air core of the fiber allows gas from the environment to diffuse into the core, which interacts with the laser signal that is carried in the air core. This work builds upon the previous LDRD project, Fiber Optic System for Direct Detection of Carbon Dioxide Leakage in Carbon Storage Wells (21-FS-003), in which the feasibility of Raman spectroscopy detection of Carbon Dioxide (CO2) in HCF detection was demonstrated. We mitigated the risk of this DCS technology by establishing and completing five objectives. The first objective was to model and optically characterize HCF uptake of CO2, establishing the relationship between HCF length, gas diffusion time, detectable gas concentration, and measured Raman intensity. In objective two, we developed a fiber core drilling recipe to enable additional diffusion ports in the fiber core and established a method for maintaining fiber strength and integrity post drilling. Objective three characterized the drilled fibers against the undrilled fibers, establishing the differences in the gas mechanics and optical properties and provided parameters to iterate the drilling process. In objective four, a fusion splicing technique was developed to join the HCF to conventional single-mode fibers, localizing the gas detection point at the drilled HCF hole, emulating a DCS. Lastly, objective five was the testing of the sensor in Edgar Mines at Colorado School of Mines on a CO2 pipeline with a simulated leak, to showcase the ability to detect CO2 leaks. This capstone result showed CO2 leak detection in < 10 minutes, raising the technology readiness level of HCF segments as deployable DCS.

organic↗

DOE OSTI2019

Effect of surface treatment of microfiberlated cellulose fibers on biocomposite properties and additive manufacturing process

Polymer additive manufacturing (AM) is a rapidly growing technology and it is transitioning to become an advanced manufacturing technique with the introduction of fiberlar reinforcing materials such as carbon and glass fibers into polymer feedstock. As a result of increasing environmental and long-term sustainability concerns, there is an increasing interest in using bio-derived cellulose fibers to reinforce composites instead of carbon and glass fibers. Melt extrusion/fused filament fabrication method is the most commonly used polymer AM technique which enables direct digital manufacturing of parts with complex geometry with a controlled anisotropic distribution of reinforcing phase. However, there are multiple factors that affect the mechanical performance of the final part such as the dispersion and orientation of the reinforcing fibers, the adhesion between the fibers and the polymer matrix, and the porosity/defects present in the part. Chemical modification of the surface of the reinforcing fibers is an effective way of improving the fiber-polymer interaction. Furthermore, the improved adhesion between the fibers and the polymer can also enhance the fiber dispersion, improve the rheological behavior of the molten feedstock and minimize the formation of porosity during the printing process, which is one of the major issues in AM. In this study, we are investigating the effect of silane surface treatment of micro-cellulose fibers on the thermal, rheological and mechanical properties of cellulose-PLA biocomposites and on the 3D-printing process. X-ray photoelectron spectroscopy results confirmed the increase in amine and silane groups on the surface of modified fibers, indicating successful functionalization. Thermal and mechanical characterization of modified fiber-PLA composites showed significant increases in storage modulus, glass transition temperature, and complex viscosity compared to neat PLA.

Tekinalp, Halil↗

NASA NTRS1991

Oxynitride glass fibers

Research at the Army Materials Technology Laboratory (AMTL) and elsewhere has shown that many glass properties including elastic modulus, hardness, and corrosion resistance are improved markedly by the substitution of nitrogen for oxygen in the glass structure. Oxynitride glasses, therefore, offer exciting opportunities for making high modulus, high strength fibers. Processes for making oxynitride glasses and fibers of glass compositions similar to commercial oxide glasses, but with considerable enhanced properties, are discussed. We have made glasses with elastic moduli as high as 140 GPa and fibers with moduli of 120 GPa and tensile strengths up to 2900 MPa. AMTL holds a U.S. patent on oxynitride glass fibers, and this presentation discusses a unique process for drawing small diameter oxynitride glass fibers at high drawing rates. Fibers are drawn through a nozzle from molten glass in a molybdenum crucible at 1550 C. The crucible is situated in a furnace chamber in flowing nitrogen, and the fiber is wound in air outside of the chamber, making the process straightforward and commercially feasible. Strengths were considerably improved by improving glass quality to minimize internal defects. Though the fiber strengths were comparable with oxide fibers, work is currently in progress to further improve the elastic modulus and strength of fibers. The high elastic modulus of oxynitride glasses indicate their potential for making fibers with tensile strengths surpassing any oxide glass fibers, and we hope to realize that potential in the near future.

Patel, Parimal J.↗