Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FUELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Performance of Vehicle Fuel System Elastomers and Plastics with Test Fuels Representing Gasoline Blended with 10% Ethanol (E10) and 16% Isobutanol (iBu16)

The compatibilities of fuel system elastomers and plastics were evaluated for test fuels containing 16 vol.% isobutanol (iBu16) and 10 vol.% ethanol (E10). Elastomers included two fluorocarbons, four acrylonitrile butadiene rubbers (NBRs), and one type of fluorosilicone, neoprene, and epichlorohydrin/ethylene oxide. Plastic materials included four nylon grades, three polyamides, polytetrafluoroethylene (PTFE), polyvinylidene fluoride (PVDF), ethylene tetrafluoroethylene (ETFE), polyphenylene sulfide (PPS), high-density polyethylene (HDPE), polybutylene terephthalate (PBT), polyoxymethylene (POM), flexible polyvinylchloride (PVC), polyetherimide (PEI), polyetheretherketone (PEEK), and a phenol formaldehyde reinforced with glass fiber (GFPF). For each polymer material, the volume, mass, and hardness were measured before and after drying. Dynamic mechanical analysis (DMA) measurements were also performed on the dried specimens.For the elastomer materials the measured properties were similar for both fuels. The fluorocarbons and fluorosilicone swelled the least (~20%), while more moderate (20-45%) expansion occurred for the two NBR hose grades and (ECO). HNBR, neoprene, and silicone exhibited high swelling and softening, which likely precludes their use in many fuel systems. For the plastic materials, the observed swell was low; Nylon 11 swelled around 15%, but otherwise, their measured swell was <10%. Many of the plastics also showed sensitivity to alcohol type, as the E10 test fuel often imparted appreciably higher swell than iBu16. In general, the plastic materials showed good compatibility with the iBu16 and E10 test fuels. Here, the sole exception was the PVC material, which was structurally degraded from exposure to either fuel type. Compositional analysis showed high fuel retention in Nylon 12 and PVC. PVC also experienced a significant reduction in plasticizer compounds following exposure, which resulted in embrittlement and an increase in the glass-to-rubber transition temperature.

33 ADVANCED PROPULSION SYSTEMS↗

Optimizing Long Term Hydrogen Fueling Infrastructure Plans on Freight Corridors for Heavy Duty Fuel Cell Electric Vehicles

The development of a future hydrogen energy economy will require the development of several hydrogen market and industry segments including a hydrogen based commercial freight transportation ecosystem. For a sustainable freight transportation ecosystem, the supporting fueling infrastructure and the associated vehicle powertrains making use of hydrogen fuel will need to be co-established. This paper develops a long-term plan for refueling infrastructure deployment using the OR-AGENT (Optimal Regional Architecture Generation for Electrified National Transportation) tool developed at the Oak Ridge National Laboratory, which has been used to optimize the hydrogen refueling infrastructure requirements on the I-75 corridor for heavy duty (HD) fuel cell electric commercial vehicles (FCEV). This constraint-based optimization model considers existing fueling locations, regional specific vehicle fuel economy and weight, vehicle origin and destination (OD), vehicle volume by class and infrastructure costs to characterize in-mission refueling requirements for a given freight corridor. The authors applied this framework to determine the ideal long term public access locations for hydrogen refueling (constrained by existing fueling stations and dispensing technology), the minimal viable cost to deploy sufficient hydrogen fuel dispensers, and associated equipment, to accommodate a growing population of hydrogen fuel cell trucks. So the framework discussed in this paper can be expanded and applied to additional electrified powertrains as well as a larger interstate system, expanded regional corridor, or other transportation networks.

08 HYDROGEN↗

Effect of hydrocarbon fuel type on fuel

A modified jet fuel thermal oxidation tester (JFTOT) procedure was used to evaluate deposit and sediment formation for four pure hydrocarbon fuels over the temperature range 150 to 450 C in 316-stainless-steel heater tubes. Fuel types were a normal alkane, an alkene, a naphthene, and an aromatic. Each fuel exhibited certain distinctive deposit and sediment formation characteristics. The effect of aluminum and 316-stainless-steel heater tube surfaces on deposit formation for the fuel n-decane over the same temperature range was investigated. Results showed that an aluminum surface had lower deposit formation rates at all temperatures investigated. By using a modified JFTOT procedure the thermal stability of four pure hydrocarbon fuels and two practical fuels (Jet A and home heating oil no. 2) was rated on the basis of their breakpoint temperatures. Results indicate that this method could be used to rate thermal stability for a series of fuels.

Wong, E. L.↗

Fuel-rich catalytic combustion: A fuel processor for high-speed propulsion

Fuel-rich catalytic combustion of Jet-A fuel was studied over the equivalence ratio range 4.7 to 7.8, which yielded combustion temperatures of 1250 to 1060 K. The process was soot-free and the gaseous products were similar to those obtained in the iso-octane study. A carbon atom balance across the catalyst bed calculated for the gaseous products accounted for about 70 to 90 percent of the fuel carbon; the balance was condensed as a liquid in the cold trap. It was shown that 52 to 77 percent of the fuel carbon was C1, C2, and C3 molecules. The viability of using fuel-rich catalytic combustion as a technique for preheating a practical fuel to very high temperatures was demonstrated. Preliminary results from the scaled up version of the catalytic combustor produced a high-temperature fuel containing large amounts of hydrogen and carbon monoxide. The balance of the fuel was completely vaporized and in various stages of pyrolysis and oxidation. Visual observations indicate that there was no soot present.

Brabbs, Theodore A.↗

Fuel-rich catalytic combustion - A fuel processor for high-speed propulsion

Fuel-rich catalytic combustion of Jet-A fuel was studied over the equivalence ratio range 4.7 to 7.8, which yielded combustion temperatures of 1250 to 1060 K. The process was soot-free and the gaseous products were similar to those obtained in the iso-octane study. A carbon atom balance across the catalyst bed calculated for the gaseous products accounted for about 70 to 90 percent of the fuel carbon; the balance was condensed as a liquid in the cold trap. It was shown that 52 to 77 percent of the fuel carbon was C1, C2, and C3 molecules. The viability of using fuel-rich catalytic combustion as a technique for preheating a practical fuel to very high temperatuers was demonstrated. Preliminary results from the scaled up version of the catalytic combustor produced a high-temperature fuel containing large amounts of hydrogen and carbon monoxide. The balance of the fuel was completely vaporized and in various stages of pyrolysis and oxidation. Visual observations indicate that there was no soot present.

Brabbs, Theodore A.↗

Turbine combustor with fuel nozzles having inner and outer fuel circuits

A combustor cap assembly for a turbine engine includes a combustor cap and a plurality of fuel nozzles mounted on the combustor cap. One or more of the fuel nozzles would include two separate fuel circuits which are individually controllable. The combustor cap assembly would be controlled so that individual fuel circuits of the fuel nozzles are operated or deliberately shut off to provide for physical separation between the flow of fuel delivered by adjacent fuel nozzles and/or so that adjacent fuel nozzles operate at different pressure differentials. Operating a combustor cap assembly in this fashion helps to reduce or eliminate the generation of undesirable and potentially harmful noise.

33 ADVANCED PROPULSION SYSTEMS↗

Separate Effects Miniature Fuel Irradiation Testing to Support Fuel Safety

The recent interest in advanced fuel forms that offer increased thermal conductivity and uranium density, as well as modifications (e.g., use of dopants or additives) to traditional UO2 fuel, necessitates a vehicle for performing high-throughput irradiation testing of these fuels before they can be safely deployed. This interest, combined with the recent decommissioning of the Halden Reactor, places a strong burden on the remaining test reactors to provide the scientific data needed to advance these fuels toward commercialization. Oak Ridge National Laboratory is actively working to alleviate some of this burden by commissioning a new “MiniFuel” test facility that will provide a vehicle for performing accelerated separate-effects irradiation testing of sub-sized nuclear fuel specimens. The small size of the fuel allows for a flexible irradiation vehicle capable of exploring a wide range of fuel performance variables within a reasonable time and cost. This paper describes the experiment facility, and the initial irradiation experiments being performed including uranium nitride (UN) kernels, coated tristructural-isotropic (TRISO) UN particles, doped and un-doped (reference) UO2 disks, U3Si2 disks, and fully ceramic microencapsulated (FCM) pellets with UN kernels and a SiC matrix. A focus is placed on the performance of miniature FCM pellets, which are being considered as the ultimate accident tolerant fuel for light water reactors. The experiments described in this paper will provide basic scientific data (e.g., swelling, fission gas release) regarding irradiation performance under well-characterized conditions.

Petrie, Christian↗

Insights on fuel performance in advanced compression ignition engines: combining engine thermodynamic trajectory and fuel ignition delay iso-contour

With the development of various low temperature engine combustion strategies, the behavior of gasoline-type fuels under compression ignition conditions has attracted extensive research interest. In this study, gasoline surrogates based on toluene primary reference fuel blends (TPRF) with different research and motor octane numbers (i.e., RON and MON) and fuel octane sensitivity (OS) have been strategically designed using a recently established surrogate model, and their combustion chemistry is further described using a well-validated kinetic mechanism. Based on a typical advanced compression ignition engine configuration, the crank angle corresponding to 50% total heat release (CA50) was utilized as an indicator of the overall fuel reactivity, and representative engine operating conditions have been selected based on the regime exhibited from the CA50 iso-contours. By combining the thermodynamic trajectory and ignition delay isocontours, useful insights on the fuel reactivity and sensitivity have been obtained to evaluate the fuel performance under various engine operating regimes with distinct chemistry, accounting for the effects of equivalence ratio and ratio of exhaust gas recirculation (EGR). This study provides useful insight on the different effects of engine operating conditions on a fuel’s performance following different engine trajectories, based on the different controlling fuel chemistry.

Tao, Mingyuan↗

A U. S. Perspective on Fast Reactor Fuel Fabrication Technology and Experience Part I: Metal Fuels and Assembly Design

This paper is Part I of a review focusing on the United States experience with metallic fast reactor fuel fabrication and assembly design for the Experimental Breeder Reactor-II and the Fast Flux Test Facility, and it also refers to the impact of development in other nations. Experience with metal fuel fabrication in the United States is extensive, including over 60 years of research conducted by the government, national laboratories, industry, and academia. This experience has culminated into a foundation of research and resulted in significant improvements to the technologies employed to fabricate metallic fast reactor fuel. This part of the review documents the current state of fuel fabrication technologies for metallic fuels, some of the challenges faced by previous researchers, and how these were overcome. Knowledge gained from reviewing previous investigations will aid both researchers and policy makers in forming future decisions relating to nuclear fuel fabrication technologies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A U. S. Perspective on Fast Reactor Fuel Fabrication Technology and Experience Part II: Ceramic Fuels

This paper is Part II of a review focusing on the United States experience with mixed oxide, carbide, and nitride fast reactor fuel fabrication, and it also refers to the impact of development in other nations. Over 60 years of research in fuel fabrication by government, national laboratories, industry, and academia has culminated into a foundation of research and resulted in significant improvements to the technologies employed to fabricate mixed oxide, carbide, and nitride fast reactor fuel. This part of the review documents the current state of fuel fabrication technologies in the United States for each of these fuel types, some of the challenges faced by previous researchers, and how these were overcome. Knowledge gained from reviewing previous investigations will aid both researchers and policy makers in forming future decisions relating to nuclear fuel fabrication technologies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fuel Properties of Oxymethylene Ethers with Terminating Groups from Methyl to Butyl

Oxymethylene ethers (OMEs) have been studied as possible additives or replacements for diesel fuels. Typically, studies have considered only methyl-terminated OMEs. Recent structure-property relationship models suggest that extended-alkyl OMEs may provide improvements to many of the properties of methyl-terminated OMEs that make them less suitable as diesel fuel blendstocks. In this work, we describe the synthesis and characterization of 16 different OMEs with methyl, ethyl, propyl, butyl, isopropyl, and isobutyl terminating alkyl groups with varying oxymethylene chain length. Indicated Cetane Number, Lower Heating Value, Flash Point, Density, Viscosity, Vapor Pressure, and Oxidative Stability are tested via ASTM standard methods. Additionally, Water Solubility, Boiling Point, seal material compatibility, and sooting propensity (via the Yield Sooting Index) are measured for these fuels. For diesel compatibility, all tested OMEs except smaller methyl and ethyl OMEs, and the branched isopropyl OME, meet cetane number requirements. Further, extending the alkyl end group increases the heating value, but all OMEs, due to their oxygen content, have heating values less than diesel; despite this, all OMEs show significant reductions in soot production per unit heating value. Only the heaviest OMEs meet diesel viscosity requirements, and most are higher density than diesel. OMEs with larger alkyl groups show the highest stability under accelerated auto-oxidation conditions. Increases in alkyl group length cause order of magnitude reduction in water solubility, from hundreds of g/L for methyl terminated OMEs to hundreds of mg/L for butyl terminated OMEs. Limited seal material testing indicates that PEEK polymers are unaffected by OMEs; while extended alkyl groups may improve compatibility with FKM (Viton), other common elastomers (NBR, silicone) remain incompatible with all tested OMEs. Overall, it is found that methyl-terminated OMEs exhibit the most potential for soot reduction, but OMEs with larger propyl and butyl terminating alkyl groups show improved compatibility with existing diesel systems.

09 BIOMASS FUELS↗

Evaluation of Tellurium as a Fuel Additive in Neodymium-Containing U-Zr Metallic Fuel

Phase-stability in a U-Zr-Te-Nd multi-component metallic fuel for advanced nuclear reactors is systematically investigated by taking into account binary, ternary and quaternary interactions between elements involved. Historically, the onset of fuel-cladding chemical interactions (FCCI) greatly limits the burnup potential of U-Zr fuels primarily due to interactions between lanthanide fission products and cladding constituents. Tellurium (Te) is evaluated as a potential additive for U-Zr fuels to bind with lanthanide fission products, e.g. neodymium (Nd), negating or mitigating the FCCI effect. Potential fresh fuel alloy compositions with the Te additive, U-Zr-Te, are characterized. Te is found to completely bind with Zr within the U-Zr matrix. Alloys simulating the formation of the lanthanide element Nd within U-Zr-Te are also evaluated, where the Te-Nd binary interaction dominates and NdTe is found to form as a high temperature stable compound. The experimental observations agree well with the trends obtained from density functional theory calculations. According to the calculated enthalpy of mixing, Zr-Te compound formation is favored in the U-Zr-Te alloy whereas NdTe compound formation is favored in the U-Zr-Te-Nd alloy. Further, the calculated charge density distribution and density of states provide sound understanding of the mutual chemical interactions between elements and phase-stability within the multi-component fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Technoeconomic and Life-Cycle Analysis of Single-Step Catalytic Conversion of Wet Ethanol into Fungible Fuel Blendstocks

Technoeconomic and life-cycle analyses are presented for catalytic conversion of ethanol to fungible hydrocarbon fuel blendstocks, informed by advances in catalyst and process development. Whereas prior work toward this end focused on 3-step processes featuring dehydration, oligomerization, and hydrogenation, the consolidated alcohol dehydration and oligomerization (CADO) approach described here results in 1-step conversion of wet ethanol vapor (40 wt% in water) to hydrocarbons and water over a metal-modified zeolite catalyst. A development project increased liquid hydrocarbon yields from 36% of theoretical to >80%, reduced catalyst cost by an order of magnitude, scaled up the process by 300-fold, and reduced projected costs of ethanol conversion 12-fold. Current CADO products conform most closely to gasoline blendstocks, but can be blended with jet fuel at low levels today, and could potentially be blended at higher levels in the future. Operating plus annualized capital costs for conversion of wet ethanol to fungible blendstocks are estimated at $2.00/GJ for CADO today and $1.44/GJ in the future, similar to the unit energy cost of producing anhydrous ethanol from wet ethanol ($1.46/GJ). Including the cost of ethanol from either corn or future cellulosic biomass but not production incentives, projected minimum selling prices for fungible blendstocks produced via CADO are competitive with conventional jet fuel when oil is $100 per barrel but not at $60 per barrel. However, with existing production incentives, the projected minimum blendstock selling price is competitive with oil at $60 per barrel. Life-cycle greenhouse gas emission reductions for CADO-derived hydrocarbon blendstocks closely follow those for the ethanol feedstock.

09 BIOMASS FUELS↗

Time-Spectral Analysis Methods for Spent Fuel Assay Using Lead Slowing-Down Spectroscopy of Spent Fuel

Nondestructive techniques for measuring the mass of fissile isotopes in spent nuclear fuel is a considerable challenge in the safeguarding of nuclear fuel cycles. A nondestructive assay technology that could provide direct measurement of fissile mass, particularly for the plutonium (Pu) isotopes, and improve upon the uncertainty of today’s confirmatory methods is needed. Lead slowing-down spectroscopy (LSDS) has been studied for the spent fuel application previously, but the nonlinear effects of assembly self shielding (of the interrogating neutron population) have led to discouraging assay accuracy for realistic pressurized water reactor fuels. In this paper, we describe the development of time-spectral analysis algorithms for LSDS intended to overcome these self-shielding effects. The algorithm incorporates the tabulated energy-dependent cross sections from key fissile and absorbing isotopes, but leaves their mass as free variables. Multi-parameter regression analysis is then used to directly calculate not only the mass of fissile isotopes in the fuel assembly (e.g., Pu-239, U-235, and Pu-241), but also the mass of key absorbing isotopes such as Pu-240 and U-238. Modeling-based assay results using a first-order self-shielding relationship indicate that LSDS has the potential to directly measure fissile isotopes with less than 5% average relative error, over a wide fuel burnup range. Shortcomings in the first-order self-shielding model and methods to improve the formulation are described.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Advanced Fuels Campaign: Light Water Reactor Accident Tolerant Fuel Performance Metrics

The safe, reliable and economic operation of the nation’s nuclear power reactor fleet has always been a top priority for the United States’ nuclear industry. As a result, continual improvement of technology, including advanced materials and nuclear fuels, remains central to industry’s success. Decades of research combined with continual operation have produced steady advancements in technology and yielded an extensive base of data, experience, and knowledge on light water reactor (LWR) fuel performance under both normal and accident conditions. In 2011, following the Great East Japan Earthquake, resulting tsunami, and subsequent damage to the Fukushima Daiichi nuclear power plant complex, enhancing the accident tolerance of LWRs became a topic of serious discussion. As a result of direction from the U.S. Congress, the U.S. Department of Energy Office of Nuclear Energy (DOE-NE) initiated an Accident Tolerant Fuel (ATF) Development program. The complex multiphysics behavior of LWR nuclear fuel makes defining specific material or design improvements difficult; as such, establishing qualitative attributes is critical to guide the design and development of fuels and cladding with enhanced accident tolerance. This report summarizes a common set of technical evaluation metrics to aid in the optimization and down selection of candidate designs. As used herein, “metrics” describe a set of technical bases by which multiple concepts can be fairly evaluated against a common baseline and against one another. Furthermore, this report describes a proposed technical evaluation methodology that can be applied to assess the ability of each concept to meet performance and safety goals relative to the current UO 2 – zirconium alloy system and relative to one another. The resultant ranked evaluation can then inform concept down-selection, such that the most promising accident tolerant fuel design option(s) can continue to be developed for lead test rod or lead test assembly insertion into a commercial reactor within the desired timeframe (by 2022).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Assessment of transition fuel cycle performance with and without a modified-open fuel cycle

The impacts of a modified-open fuel cycle (MOC) option as a transition step from the current once-through cycle (OTC) to a full-recycle fuel cycle (FRC) were assessed using the nuclear systems analysis code DANESS. The MOC of interest for this study was mono-recycling of plutonium in light water reactors (LWR-MOX). Two fuel cycle scenarios were evaluated with and without the MOC option: a 2-stage scenario with a direct path from the current fleet to the final FRC, and a 3-stage scenario with the MOC option as a transition step. The FRC reactor (fast reactor) was assumed to deploy in 2050 for both scenarios, and the MOC reactor in the 3-stage scenario was assumed to deploy in 2025. The last LWRs (using either UOX or MOX fuels) come online in 2050 and are decommissioned by 2110. Thus, the FRC is achieved after 2110. The reprocessing facilities were assumed to be available 2 years prior to the deployment of the MOC and FRC reactors with maximum reprocessing capacities of 2000 tHM/yr and 500 tHM/t for LWR-UOX and LWR-MOX used nuclear fuels (UNFs), respectively. Under a 1% nuclear energy demand growth assumption, both scenarios were able to sustain a full transition to the FRC without delay. For the 3-stage scenario, the share of LWR-MOX reactors reaches a peak of 15% of installed capacity, which resulted in 10% lower cumulative uranium consumption and SWU requirements compared to the 2-stage scenario during the transition period. The peak UNF storage requirement decreases by 50% in the 3-stage scenario, largely due to the earlier deployment of the reprocessing plants to support the MOC fuel cycle. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

New Approach to Eccentric Positioning of Fuel Assemblies in a Spent Fuel Pool

Criticality analyses of a spent fuel pool (SFP) typically assume the fuel assemblies are centered in the cells. In reality fuel assemblies are not constrained to be centered but can be placed anywhere within the available space. For SFPs with absorber panels it has been shown that the most reactive condition is with the fuel assemblies centered. However, for SFPs without absorber panels eccentric positioning of assemblies increases reactivity. Historically, it was common practice to analyze eccentric positioning by modeling a 2x2 arrangement of the fuel where each assembly is positioned toward the center (with reflective or periodic bounding conditions). The delta k between the eccentric model and the center model was taken as an uncertainty which was then statistically combined with other uncertainties. This historical approach had two problems. First, arrangement of more than 4 assemblies placed toward the center of the model produced higher k's. Second, in a large pool it was likely that 4 assemblies collocated toward each other would exist so asymmetry should be treated as a bias rather than an uncertainty. The number of collocated assemblies is important to the magnitude of the effect. Since spent fuel pools are large it is expected that some collocated eccentrically placed assemblies will occur so the eccentric placement reactivity should be accounted for by a bias. The magnitude of this bias depends greatly on the number of eccentrically placed assemblies that are collocated. A simple probability model assuming random placement can be used to establish the number of collated eccentric assemblies. It has been shown that for a SFP with 800 cells there is less than a 5% probability that more than 16 eccentric assemblies will be collocated. The eccentricity bias using 16 eccentric assemblies collocated is small (on the order of 0.001 in delta k or less) and should be easy to add as a bias in the SFP criticality analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Swelling of Uranium Dioxide–Silumin Dispersion Fuel Composition in Experimental Fuel Elements of the SM Reactor

A variant of experimental dispersion fuel elements with a displacer and uranium dioxide-silumin fuel composition, which were proposed for modernizing the core of the SM reactor, was investigated. The fuel elements were irradiated in a wide spectrum of neutron- and thermophysical parameters of the reactor’s reflector channel. The fuel elements showed satisfactory radiation resistance at thermal flux density 5.8–8 MW/m{sup 2} and burnup to 45%. The swelling of the fuel composition was analyzed. It is shown that of three possible components of the swelling the one due to gaseous fission products makes the main contribution, approximately 3/4 of the total amount. The interaction of the fuel components results in compaction of the kernel and promotes some compensation of the swelling, increasing as the interaction increases. These investigations show that the depth of burnup at the achieved thermal flux density for fuel elements with a displacer is not the limit.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗