Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Radiation-Induced Damage of Silicon-Carbide Diodes by High-Energy Particles

The radiation hardness of three types of commercial Schottky rectifier diodes based on silicon carbide (4H-SiC, base layer doping level (3–7) × 10{sup 15} cm{sup –3}) under electron (0.9 or 3.5 MeV electrons) and proton irradiation (15 MeV protons) is studied. The forward and reverse current–voltage characteristics of the diodes are monitored. In the initial state, the diodes have a breakdown voltage of 1–2 kV and an almost ideal forward current–voltage characteristic. It is found that the series resistance of the diodes is the most sensitive to radiation and governs the radiation hardness. This resistance grows by nearly 10 orders of magnitude and reaches a value of 10{sup 9} Ω at high doses. The threshold doses of electron irradiation fall within the range D{sub th} ≈ (0.5–2) × 10{sup 16} cm{sup –2} and depend on the electron energy and doping level of the base layer, and those of proton irradiation, D{sub th} ≈ 5 × 10{sup 13} cm{sup –2}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Filamentation and Self-Focusing of Electron Beams in Vacuum and Gas Diodes

In this paper, we experimentally studied pulsed electron beams with a high local density. The conditions in which the energy density cumulation is observed during the interaction of electrons with the anode are shown to develop in vacuum and gas diodes at nanosecond and subnanosecond durations of a beam current pulse and a decrease in the interelectrode gap. The average electron energy in filamentation and self-focusing of an electron beam in a vacuum diode of an accelerator at a current of ~2 kA and a no-load voltage of ~400 kV was established to be 50–100 keV while the energy density was 10{sup 9}–10{sup 10} J/cm{sup 3}. It is confirmed that the beam current density in a gas diode can exceed 1 kA/cm{sup 2}. It is hypothesized that superdense electron beams in vacuum and gas diodes are formed as a result of avalanche multiplication of runaway electrons in the cathode–anode gap plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Non-Reciprocal Geometric Wave Diode by Engineering Asymmetric Shapes of Nonlinear Materials

Unidirectional nonreciprocal transport is at the heart of many fundamental problems and applications in both science and technology. Here we study how to design the novel wave diode devices to realize the non-reciprocal wave propagations. Analytical results reveal that such non-reciprocal wave propagation can be purely induced by asymmetric geometry in nonlinear materials. The detailed numerical simulations are performed for a more realistic geometric wave diode model with typical asymmetric shape, where good non-reciprocal wave diode effect has been demonstrated. The results open a way for making wave diodes efficiently simply through shape engineering.

36 MATERIALS SCIENCE↗

Analysis of the IBL and LBNL irradiated PIN and PN diodes

This report is a follow-up to the previous report on the difference between high fluence, high and low flux irradiations. There was a discrepancy in the data for the LBNL irradiated S5821 PIN diodes. There were diodes irradiated in the two batches (high and low flux) with the same flux and fluence for reference (lell ions/cm 2 /shot and 5, 10, and 20 ions/cm 2 total flux). Although these diodes should have the same electrical characteristics their leakage currents were different by a factor of 5-6 (batch 2 was larger). Also, the C-V measurements showed drastically different results. It was speculated that these discrepancies were due to one of the following two reasons: 1. Different times elapsed between radiation and characterization. 2. Different areas were irradiated (roughly half of the diodes were covered during irradiation). To address the first concern, we annealed the devices according to the ASTM standard [1]. The differences remained the same. To determine the irradiated area, we performed large area IBIC scans on several devices. Error! Reference source not found. below shows the IBIC maps of two devices one from each batch. The irradiated areas are approximately the same.

42 ENGINEERING↗

Synthesis and Characterization of Superconductor Diodes

In the era of modern computing, quantum bits (or qubits) are extensively researched due to their ability to perform computations exponentially faster than classical computers. One promising method for synthesizing qubits on a macroscopic scale is through superconductor diodes (SDs). Unfortunately, SDs are currently limited by their dependence on extremely low temperatures (T ≈ 0K), which restricts their practical usability at larger scales. To address this limitation, researchers are exploring new materials and methods to identify superconductors with higher critical temperatures. My research at the Lawrence Livermore National Laboratory (LLNL) focuses on synthesizing and characterizing superconductor diodes to determine their efficiency for quantum computing applications. Bismuth thin films were synthesized with magnetron sputtering with separate thicknesses which provides information on methods to alter their resistivity. Bismuth was characterized as the topological insulator used in the diode, and its resistivity was measured using a standard four-point probe technique with 1 mA current. Bismuth (99.99% pure) was then purified in a tubular furnace at 400C to use within a Josephson junction as a topological insulator. Niobium and Tantalum Josephson junctions were then synthesized, and they were characterized using a lock-in amplifier four-point probe technique. Materials such as niobium and tantalum are used in high-entropy alloy research, which is a relatively new class of material that has little research within the superconductor diode community, yet the current research shows promise. We anticipate that testing high-entropy superconductors will reveal crucial factors, potentially leading to the development of high-temperature superconductors in the future.

36 MATERIALS SCIENCE↗

Fabricating Graphene Oxide/h-BN Metal Insulator Semiconductor Diodes by Nanosecond Laser Irradiation

To employ graphene’s rapid conduction in 2D devices, a heterostructure with a broad bandgap dielectric that is free of traps is required. Within this paradigm, h-BN is a good candidate because of its graphene-like structure and ultrawide bandgap. We show how to make such a heterostructure by irradiating alternating layers of a-C and a-BN film with a nanosecond excimer laser, melting and zone-refining constituent layers in the process. With Raman spectroscopy and ToF-SIMS analyses, we demonstrate this localized zone-refining into phase-pure h-BN and rGO films with distinct Raman vibrational modes and SIMS profile flattening after laser irradiation. Furthermore, in comparing laser-irradiated rGO-Si MS and rGO/h-BN/Si MIS diodes, the MIS diodes exhibit an increased turn-on voltage (4.4 V) and low leakage current. The MIS diode I-V characteristics reveal direct tunneling conduction under low bias and Fowler-Nordheim tunneling in the high-voltage regime, turning the MIS diode ON with improved rectification and current flow. This study sheds light on the nonequilibrium approaches to engineering h-BN and graphene heterostructures for ultrathin field effect transistor device development.

2D materials↗

MicroPulse DIAL (MPD) – a diode-laser-based lidar architecture for quantitative atmospheric profiling

Abstract. Continuous water vapor and temperature profiles are critically needed for improved understanding of the lower atmosphere and potential advances in weather forecasting skill. Ground-based, national-scale profiling networks are part of a suite of instruments to provide such observations; however, the technological method must be cost-effective and quantitative. We have been developing an active remote sensing technology based on a diode-laser-based lidar technology to address this observational need. Narrowband, high-spectral-fidelity diode lasers enable accurate and calibration-free measurements requiring a minimal set of assumptions based on direct absorption (Beer–Lambert law) and a ratio of two signals. These well-proven quantitative methods are known as differential absorption lidar (DIAL) and high-spectral-resolution lidar (HSRL). This diode-laser-based architecture, characterized by less powerful laser transmitters than those historically used for atmospheric studies, can be made eye-safe and robust. Nevertheless, it also requires solar background suppression techniques such as narrow-field-of-view receivers with an ultra-narrow bandpass to observe individual photons backscattered from the atmosphere. We discuss this diode-laser-based lidar architecture's latest generation and analyze how it addresses a national-scale profiling network's need to provide continuous thermodynamic observations. The work presented focuses on general architecture changes that pertain to both the water vapor and the temperature profiling capabilities of the MicroPulse DIAL (MPD). However, the specific subcomponent testing and instrument validation presented are for the water vapor measurements only. A fiber-coupled seed laser transmitter optimization is performed and shown to meet all of the requirements for the DIAL technique. Further improvements – such as a fiber-coupled near-range receiver, the ability to perform quality control via automatic receiver scanning, advanced multi-channel scalar capabilities, and advanced processing techniques – are discussed. These new developments increase narrowband DIAL technology readiness and are shown to allow higher-quality water vapor measurements closer to the surface via preliminary intercomparisons within the MPD network itself and with radiosondes.

Spuler, Scott M.↗

Circuit model for characterizing the nearly linear behavior of avalanche diodes in amplifier circuits

A nonlinear circuit model for avalanche diodes is proposed. The model was derived by assuming that the bias dependence of the elements in a known small-signal equivalent-circuit model for existing diodes arises in a manner consistent with the theory of an idealized Read-type device. The model contains a nonlinear R-L branch, a controlled source, and a linear depletion capacitance. The model is used in the nearly linear sense to predict intermodulation distortion and gain compression in avalanche diode amplifiers. Computed results for amplifiers with existing diodes are shown to be in good agreement with experiment.

Penfield, P., Jr.↗

Development of a thermal diode heat pipe for the advanced thermal control flight experiment /ATFE/.

Description of the analysis, design, fabrication, and test of the engineering model of the ATFE diode. Included is a review of several diode concepts that led to selection of the liquid blockage technique for shut-off. The diode is made of stainless steel, 26 in. long, 0.375-in. nominal OD, with self-filling spiral artery wick and ammonia working fluid. In the normal heat pipe mode, at ambient temperatures, the diode capacity is 85 W. For flight, the pipe will deliver 20 W with a 9 F temperature difference between the external evaporator and condenser surfaces. Reverse mode conduction is less than 1.5 W with a 260 F temperature difference.

Swerdling, B.↗

High-efficiency, low-temperature cesium diodes with lanthanum-hexaboride electrodes

Lanthanum hexaboride electrodes in 1700 K cesium diodes may triple power outputs compared with those demonstrated for nuclear thermionic space applications. Still greater relative gains seem possible for emitters below 1700 K. Further improvements in cesium diode performance should result from the lower collector temperatures allowed for earth and low power space duties. Decreased temperatures will lessen thermal transport losses that attend thermionic conversion mechanisms. Such advantages will add to those from collector Carnot and electrode effects. If plasma ignition difficulties impede diode temperature reductions, recycling small fractions of the output power could provide ionization. So high efficiency, low temperature cesium diodes with lanthanum hexaboride electrodes appear feasible.

Morris, J. F.↗

High-efficiency, low-temperature cesium diodes with lanthanum-hexaboride electrodes

Lanthanum-hexaboride electrodes in 1700 K cesium diodes may triple power outputs compared with those demonstrated for nuclear thermionic space applications. Still greater relative gains seem possible for emitters below 1700 K. Further improvements in cesium-diode performance should result from the lower collector temperatures allowed for earth and low-power-space duties. Decreased temperatures will lessen thermal-transport losses that attend thermionic-conversion mechanisms. Such advantages will add to those from collector-Carnot and electrode effects. If plasma ignition difficulties impede diode temperature reductions, recycling small fractions of the output power could provide ionization. So high-efficiency, low-temperature cesium diodes with lanthanum-hexaboride electrodes appear feasible.

Morris, J. F.↗

Diode pumped Nd:YAG laser development

A low power Nd:YAG laser was constructed which employs GaAs injection lasers as a pump source. Power outputs of 125 mW TEM CW with the rod at 250 K and the pump at 180 K were achieved for 45 W input power to the pump source. Operation of the laser, with array and laser at a common heat sink temperature of 250 K, was inhibited by difficulties in constructing long-life GaAs LOC laser arrays. Tests verified pumping with output power of 20 to 30 mW with rod and pump at 250 K. Although life tests with single LOC GaAs diodes were somewhat encouraging (with single diodes operating as long as 9000 hours without degradation), failures of single diodes in arrays continue to occur, and 50 percent power is lost in a few hundred hours at 1 percent duty factor. Because of the large recent advances in the state of the art of CW room temperature AlGaAs diodes, their demonstrated lifetimes of greater than 5,000 hours, and their inherent advantages for this task, it is recommended that these sources be used for further CW YAG injection laser pumping work.

Reno, C. W.↗

Parametric Performance of a Spiral-Artery, Liquid-Trap-Diode Heat Pipe

A series of parametric investigations are described which determine the effect of various fluid charges on the performance of a 0.635-cm-diam spiral-artery, liquid-trap diode in both the forward and reverse modes. Specific parameters such as forward- and reverse-mode conductances, shutdown times and energies, and recovery to forward-model operation, are evaluated for ethane as a working fluid in the temperature range 170 K to 220 K. Results indicate that the heat pipe will not reliably start up in the forward mode. However, startup can be initiated when preceded by a diode reversal. Also included are data which show the susceptibility of the diode to fluid charge and tilt. The optimum fluid charge was found to be 2.67 g and transport capability at this charge was in excess of 1200 W-cm at 200 K. The diode in the reverse mode exhibited a rapid shutdown (within 9 min) with a shutdown energy of 1150 J (0.32 Wh).

Williams, R. J.↗

Investigation of a cryogenic thermal diode

This paper describes a series of parametric investigations to determine the effect of various fluid charges on the performance of a 0.635-cm-diameter spiral-artery, liquid-trap diode in both the forward and reverse modes. Specific parameters such as forward- and reverse-mode conductances, shutdown times and energies, and recovery to forward-mode operation, are evaluated for ethane as a working fluid in the temperature range 170 K to 220 K. Results indicate that the heat pipe will not reliably start up in the forward mode. However, startup can be initiated when preceded by a diode reversal. Also concluded are data which show the susceptibility of the diode to fluid charge and tilt. The optimum fluid charge was found to be 2.67 g, and transport capability at this charge was in excess of 1200 W-cm at 200 K. The diode in the reverse mode exhibited a rapid shutdown (within 9 min) with a shutdown energy of 1150 J (0.32 Wh).

Williams, R. J.↗

Cryogenic thermal diode heat pipes

The development of spiral artery cryogenic thermal diode heat pipes was continued. Ethane was the working fluid and stainless steel the heat pipe material in all cases. The major tasks included: (1) building a liquid blockage (blocking orifice) thermal diode suitable for the HEPP space flight experiment; (2) building a liquid trap thermal diode engineering model; (3) retesting the original liquid blockage engineering model, and (4) investigating the startup dynamics of artery cryogenic thermal diodes. An experimental investigation was also conducted into the wetting characteristics of ethane/stainless steel systems using a specially constructed chamber that permitted in situ observations.

Alario, J.↗

Shot-noise in resistive-diode mixers and the attenuator noise model

The representation of a pumped exponential diode, operating as a mixer, by an equivalent lossy network, is reexamined. It is shown that the model is correct provided the network has ports for all sideband frequencies at which (real) power flow can occur between the diode and its embedding. The temperature of the equivalent network is eta/2 times the physical temperature of the diode. The model is valid only if the series resistance and nonlinear capacitance of the diode are negligible. Expressions are derived for the input and output noise temperature and the noise-temperature ratio of ideal mixers. Some common beliefs concerning noise-figure and noise-temperature ratio are shown to be incorrect.

Kerr, A. R.↗

Application of tunable diode lasers as local oscillators in an Infrared Heterodyne Radiometer (IHR)

The utility of diode lasers as local oscillators (LOs) in a heterodyne receiver application was investigated. The CW power, spectral tunability, spectral stability, and spatial intensity distribution of the TDL outputs were measured. A tunable diode laser LO was incorporated into a laboratory Dicke-switched infrared heterodyne setup and used to measure radiometer sensitivity as well as spectroscopic characteristics of selected absorption lines of ammonia. The test results on one of the two tunable diode lasers are emphasized in an attempt to provide a comprehensive data package which may be useful for future planning purposes. The second tunable diode laser exhibits characteristics similar to the fully tested TDL with the exception that some changes in its performance characteristics as it was temperature cycled between room temperature and the operating temperature of approximately 50K occurred.

Savage, M. G.↗

Simple cryogenic temperature regulator - The Zener diode

For obtaining optimum performance from cooled infrared detectors used in astronomy, it is often necessary to operate the preamplifier transistor (usually a JFET) at a higher temperature than that provided by the cryogen. Various means of elevating the temperature of the FET above the temperature of its environment are considered. A description is presented of a method which uses a 10 V Zener diode (actually an avalanche diode) as a self-stabilizing heater element. The diode is mounted in good thermal contact with the FET, and both are isolated from the work surface by a link of poor conductivity. The diode is driven by a stable, constant voltage power supply.

Storey, J. W. V.↗