Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Digital control hardware”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Distributed asynchronous microprocessor architectures in fault tolerant integrated flight systems

The paper discusses the implementation of fault tolerant digital flight control and navigation systems for rotorcraft application. It is shown that in implementing fault tolerance at the systems level using advanced LSI/VLSI technology, aircraft physical layout and flight systems requirements tend to define a system architecture of distributed, asynchronous microprocessors in which fault tolerance can be achieved locally through hardware redundancy and/or globally through application of analytical redundancy. The effects of asynchronism on the execution of dynamic flight software is discussed. It is shown that if the asynchronous microprocessors have knowledge of time, these errors can be significantly reduced through appropiate modifications of the flight software. Finally, the papear extends previous work to show that through the combined use of time referencing and stable flight algorithms, individual microprocessors can be configured to autonomously tolerate intermittent faults.

Dunn, W. R.↗

The SIFT hardware/software systems. Volume 1: A detailed description

This report contains a detailed description of the software implemented fault-tolerant computer's operating system and hardware subsystems. The Software Implemented Fault-Tolerant (SIFT) computer system was developed as an experimental vehicle for fault-tolerant systems research. The SIFT effort began with broad, in-depth studies stating the reliability and processing requirements for digital computers which would, in the aircraft of the 1990's, control flight-critical functions.

Palumbo, Daniel L.↗

On-board switching and processing

Findings from NASA's space electronics division's (SED's) advanced systems studies related to future communications satellite services that will require onboard switching and processing technology are reviewed. SED's digital signal switching and processing technology program is reviewed. This program responds to specific systems technology development needs for enabling commercial development of future satellite services. The technologies include: modulators, demodulators, and forward error-correction hardware for space- and ground-based applications; onboard information switching and processing, onboard network control, and health monitoring; and cost-efficient ground terminals. The in-house systems integration, test, and evaluation (SITE) project, which includes a laboratory testbed for evaluating technology in a simulated systems environment, is reviewed.

Harrold, Joseph L.↗

Space Acceleration Measurement System for Free Flyers

Experimenters from the fluids, combustion, materials, and life science disciplines all use the microgravity environment of space to enhance their understanding of fundamental physical phenomena caused by disturbances from events such as spacecraft maneuvers, equipment operations, atmospheric drag, and (for manned flights) crew movement. Space conditions reduce gravity but do not eliminate it. To quantify the level of these disturbances, NASA developed the Space Acceleration Measurement System (SAMS) series to collect data characterizing the acceleration environment on the space shuttles. This information is provided to investigators so that they can evaluate how the microgravity environment affects their experiments. Knowledge of the microgravity environment also helps investigators to plan future experiments. The original SAMS system flew 20 missions on the shuttle as well as on the Russian space station Mir. Presently, Lewis is developing SAMS-II for the International Space Station; it will be a distributed system using digital output sensor heads. The latest operational version of SAMS, SAMS-FF, was originally designed for free flyer spacecraft and unmanned areas. SAMS-FF is a flexible, modular system, housed in a lightweight package, and it uses advances in technology to improve performance. The hardware package consists of a control and data acquisition module, three different types of sensors, data storage devices, and ground support equipment interfaces. Three different types of sensors are incorporated to measure both high- and low-frequency accelerations and the roll rate velocity. Small, low-power triaxial sensor heads (TSH's) offer high resolution and selectable bandwidth, and a special low-frequency accelerometer is available for high-resolution, low-frequency applications. A state-of-the-art, triaxial fiberoptic gyroscope that measures extremely low roll rates is housed in a compact package. The versatility of the SAMS-FF system is shown in the three different types of missions SAMS-FF has supported.

Kacpura, Thomas J.↗

Real-Time Digital Simulation of Inertial Response with Hardware-in-the-Loop Implementation on the CART3 Wind Turbine at the National Wind Technology Center

With increasing penetrations of wind power on electric grids, the stability and reliability of interconnected power systems may be impacted. In some countries that have developed renewable energy sources and systems, grid codes have been revised to require wind power plants (WPPs) to provide ancillary services to support the power system frequency in case of severe grid events. To do this, wind turbine generators (WTGs) should be deloaded to reserve a certain amount of active power for primary frequency response; however, deloading curtails annual energy production, and the market for this type of service needs to be further developed. In this report, we focus on the temporary frequency support provided by WTGs through inertial response. WTGs have potential to provide inertial response, but appropriate control methods should be implemented. With the implemented inertial control methods, wind turbines are capable of increasing their active power output by releasing some of their stored kinetic energy when a frequency excursion occurs. Active power can be temporarily boosted above the maximum power points, after which the rotor speed decelerates, and subsequently an active power output reduction restores the kinetic energy. In this report, we develop two types of models for wind power systems: the first is common, based on the wind power aerodynamic equation, and the power coefficient can be regressed using nonlinear functions; the second is much more complicated, wherein the wind turbine system is modeled using the Fatigue, Aerodynamics, Structures, and Turbulence Modeling (FAST) tool with several degrees of freedoms. A nine-bus test power system is built in Simulink and the Real-Time Digital Simulator, respectively, which are used to evaluate the frequency support performance of the WPPs. We implement two distinct types of inertial control methods in the modeled wind turbines: frequency-based inertial control (FBIC) and stepwise inertial control (SIC). We compare the performances of the two methods in terms of their frequency nadirs, rates of change of frequency, and recovery times. We conclude the results under various wind speeds and penetration cases, which provide insight into designing the inertial response of WTGs. Further, we discuss the impact of the parameters on the performance of the inertial control methods. We evaluate both the scaling factors for the FBIC method and the slope values for the TLIC methods. The simulation work shows the characteristics of different inertial responses compared to conventional synchronous generators. Based on the simulation results, we modify, improve, and test the inertial control methods under a more realistic wind turbine model based on FAST. We then validate the inertial responses under highly turbulent wind conditions generated by TurbSim, and we examine their influences on the turbine mechanical components. The extensive simulation proves the effectiveness of the proposed inertial control methods as well as the nine-bus test power system. We then reconsider the parameters. We rebuild the same test power system using Real time Simulator Computer Aided Design (RSCAD), and we implement the inertial control methods in the real Controls Advanced Research Turbine (CART3), which is prepared for the hardware-in-the-loop field-test simulation. After the setups for the hardware and software hybrid simulation platform are complete, the inertial response is further tested on a real wind turbine for the first time, in which CART3 release the controlled inertial response against the emulated frequency excursion, provided by the real-time simulated power system test bed in RTDS.

17 WIND ENERGY↗

Failure detection and control-system reconfiguration: Past, present, and future

The history of failure detection and redundancy management in aircraft applications is reviewed. To date, techniques related to that subject have been based mainly on hardware duplication of like components with failure monitoring and switchover or averaging for redundancy management. Specific examples of these techniques are discussed as they have been applied to the NASA F-8 Digital Fly-by-Wire aircraft and are to be applied to the space shuttle vehicle in the near future.

Montgomery, R. C.↗

An Integrated Risk Assessment Process of Safety-Related Digital I&C Systems in Nuclear Power Plants

Upgrading the existing analog instrumentation and control (I&C) systems to state-of-the-art digital I&C (DI&C) systems will greatly benefit existing light water reactors. However, the issue of software common cause failure (CCF) remains an obstacle in terms of qualification for digital technologies. Existing analyses of CCFs in I&C systems mainly focus on hardware failures. With the application and upgrading of new DI&C systems, design flaws could cause software CCFs to become a potential threat to plant safety, considering that most redundancy designs use similar digital platforms or software in their operating and application systems. With complex multilayer redundancy designs to meet the single failure criterion, these I&C safety systems are of particular concern in U.S. Nuclear Regulatory Commission licensing procedures. In Fiscal Year 2019, the Risk-Informed Systems Analysis (RISA) Pathway of the U.S. Department of Energy’s Light Water Reactor Sustainability Program initiated a project to develop a risk assessment strategy for delivering a strong technical basis to support effective, licensable, and secure DI&C technologies for digital upgrades and designs. An integrated risk assessment for the DI&C process was proposed for this strategy to identify potential key digital-induced failures, implement reliability analyses of related digital safety I&C systems, and evaluate the unanalyzed sequences introduced by these failures (particularly software CCFs) at the plant level. Here this paper summarizes these RISA efforts in the risk analysis of safety-related DI&C systems at Idaho National Laboratory.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

LCLS-II Gun/Buncher LLRF System Design

For a free electron laser, the stability of injector is critical to the final electron beam parameters, e.g., beam energy, beam arrival time, and eventually it determines the photon quality. The LCLS-II project's injector contains a VHF copper cavity as the gun and a two-cell L-band copper cavity as its buncher. The cavity designs are inherited from the APEX design, but requires more field stability than demonstrated in APEX operation. The gun LLRF system design uses a connectorized RF front end and low noise digitizer, together with the same general purpose FPGA carrier board used in the LCLS-II SRF LLRF system. The buncher LLRF system directly adopts the SRF LLRF chassis design, but programs the controller to run the normal conducting cavities. In this paper, we describe the gun/buncher LLRF system design, including the hardware design, the firmware design and bench test.

43 PARTICLE ACCELERATORS↗

Triggering Klystrons

To determine if klystrons will perform to the specifications of the LCLS (Linac Coherent Light Source) project, a new digital trigger controller is needed for the Klystron/Microwave Department Test Laboratory. The controller needed to be programmed and Windows based user interface software needed to be written to interface with the device over a USB (Universal Serial Bus). Programming the device consisted of writing logic in VHDL (VHSIC (Very High Speed Integrated Circuits) hardware description language), and the Windows interface software was written in C++. Xilinx ISE (Integrated Software Environment) was used to compile the VHDL code and program the device, and Microsoft Visual Studio 2005 was used to compile the C++ based Windows software. The device was programmed in such a way as to easily allow read/write operations to it using a simple addressing model, and Windows software was developed to interface with the device over a USB connection. A method of setting configuration registers in the trigger device is absolutely necessary to the development of a new triggering system, and the method developed will fulfill this need adequately. More work is needed before the new trigger system is ready for use. The configuration registers in the device need to be fully integrated with the logic that will generate the RF signals, and this system will need to be tested extensively to determine if it meets the requirements for low noise trigger outputs.

Stefan, Kelton D.↗

Rotorcraft flight-propulsion control integration

The parallel development of digital engine and flight controls for U.S. Army helicopters has made possible the future derivation of a fully integrated digital flight/propulsion control system. A NASA/Army research program has been undertaken to exploit these possibilities, ultimately yielding a generation of helicopters with exceptional agility and maneuverability in military roles and low pilot workloads in all-weather civil aviation missions. The program's three phases respectively address system modeling and analysis, flight hardware and software development, and flight evaluations aboard a research vehicle.

Mihaloew, J. R.↗

Presentation on a Space Acceleration Measurement System (SAMS)

The primary objective of the Space Acceleration Measurement Systems (SAMS) project is to provide an acceleration measurement system capable of serving a wide variety of space experiments. The design of the system being developed under this project takes into consideration requirements for experiments located in the middeck, in the orbiter bay, and in Spacelab. In addition to measuring, conditioning, and recording accelerations, the system will be capable of performing complex calculations and interactive control. The main components consist of a remote triaxial optical storage device. In operation, the triaxial sensor head produces output signals in response to acceleration inputs. These signals are preamplified, filtered and converted into digital data which is then transferred to optical memory. The system design is modular, facilitating both software and hardware upgrading as technology advances. Two complete acceleration measurement flight systems will be build and tested under this project.

Chase, Theodore L.↗

Fault Detection and Correction for the Solar Dynamics Observatory Attitude Control System

The Solar Dynamics Observatory is an Explorer-class mission that will launch in early 2009. The spacecraft will operate in a geosynchronous orbit, sending data 24 hours a day to a devoted ground station in White Sands, New Mexico. It will carry a suite of instruments designed to observe the Sun in multiple wavelengths at unprecedented resolution. The Atmospheric Imaging Assembly includes four telescopes with focal plane CCDs that can image the full solar disk in four different visible wavelengths. The Extreme-ultraviolet Variability Experiment will collect time-correlated data on the activity of the Sun's corona. The Helioseismic and Magnetic Imager will enable study of pressure waves moving through the body of the Sun. The attitude control system on Solar Dynamics Observatory is responsible for four main phases of activity. The physical safety of the spacecraft after separation must be guaranteed. Fine attitude determination and control must be sufficient for instrument calibration maneuvers. The mission science mode requires 2-arcsecond control according to error signals provided by guide telescopes on the Atmospheric Imaging Assembly, one of the three instruments to be carried. Lastly, accurate execution of linear and angular momentum changes to the spacecraft must be provided for momentum management and orbit maintenance. In th~sp aper, single-fault tolerant fault detection and correction of the Solar Dynamics Observatory attitude control system is described. The attitude control hardware suite for the mission is catalogued, with special attention to redundancy at the hardware level. Four reaction wheels are used where any three are satisfactory. Four pairs of redundant thrusters are employed for orbit change maneuvers and momentum management. Three two-axis gyroscopes provide full redundancy for rate sensing. A digital Sun sensor and two autonomous star trackers provide two-out-of-three redundancy for fine attitude determination. The use of software to maximize chances of recovery from any hardware or software fault is detailed. A generic fault detection and correction software structure is used, allowing additions, deletions, and adjustments to fault detection and correction rules. This software structure is fed by in-line fault tests that are also able to take appropriate actions to avoid corruption of the data stream.

Starin, Scott R.↗

Return to Mercury: A Comparison of Solar Simulation and Flight Data for the MESSENGER Spacecraft

The MErcury, Surface, Space, ENvironment GEochemistry and Ranging (MESSENGER) spacecraft is a NASA Discovery Mission spacecraft developed and operated by the Johns Hopkins University Applied Physics Laboratory. It was launched on August 3, 2004 and is currently on a course for Mercury orbit insertion in March 2011. To date the mission trajectory has taken the spacecraft to minimum solar distances of 0.332 and 0.313 AU and on January 14, 2008 the first flyby of Mercury in 33 years. From launch through the latest perihelion passage temperature performance data has been collected for the sun facing Digital Sun Sensors (DSS), the sun facing phased array and low gain (omni) antennas, the solar arrays, the sunshade and the two sun facing attitude control 4.4 N thrusters. Prior to launch, extensive solar simulation testing was conducted at the Glenn Research Center, Tank 6 solar simulation facility in Cleveland Ohio. Flight hardware qualification units representing these Sun exposed components were tested in solar environments that represented near mission minimum solar distance as to verify the thermal designs and the material used in fabrication. The paper will review the thermal designs of these components and their thermal performance to date as compared to the solar simulation testing.

Ercol, Carl J.↗

OpenSQUID: A Flexible Open-Source Software Framework for the Control of SQUID Electronics

We report commercially available computer-controlled SQUID electronics are usually delivered with software providing a basic user interface for adjustment of SQUID tuning parameters, such as bias current, flux offset, and feedback loop settings. However, in a research context it would often be useful to be able to modify this code and/or to have full control over all these parameters from researcher-written software. In the case of the STAR Cryoelectronics PCI/PFL family of SQUID control electronics, the supplied software contains modules for automatic tuning and noise characterization, but does not provide an interface for user code. On the other hand, the Magnicon SQUIDViewer software package includes a public application programming interface (API), but lacks auto-tuning and noise characterization features. To overcome these and other limitations, we are developing an "open-source" framework for controlling SQUID electronics which should provide maximal interoperability with user software, a unified user interface for electronics from different manufacturers, and a flexible platform for the rapid development of customized SQUID auto-tuning and other advanced features. Finally, we have completed a first implementation for the STAR Cryoelectronics hardware and have made the source code for this ongoing project available to the research community on SourceForge (http://opensquid.sourceforge.net) under the GNU public license.

47 OTHER INSTRUMENTATION↗

Application of Optical Measurement Techniques During Fabrication and Testing of Liquid Rocket Nozzles

This paper presents a series of optical measurement techniques that were developed for use during large-scale fabrication and testing of nozzle components. A thorough understanding of hardware throughout the fabrication cycle and hotfire testing is critical to meet component design intent. Regeneratively cooled nozzles and associated tooling require tight control of tolerances during the fabrication process to ensure optimal performance. Additionally, changes in geometry during testing can affect performance of the nozzle and mating components. Structured light scanning and digital image correlation techniques were used to collect data during the fabrication and test of nozzles, in addition to other engine components. This data was used to analyze deformations data during machining, heat treatment, assembly and testing operations. A series of feasibility experiments were conducted for these techniques that led to use on full scale nozzles during the J-2X upper stage engine program in addition to other engine development programs. This paper discusses the methods and results of these measurement techniques throughout the nozzle life cycle and application to other components.

Gradl, Paul R.↗

Reference manual for the Langley Research Center flight simulation computing system

The researchers at the Langley Research Center Flight Simulation Computing System are provided with an advanced real-time digital simulation capability. This capability is controlled at the user interface level by the Real Time Simulation Supervisor. The Supervisor is a group of subprograms loaded with a simulation application program. The Supervisor provides the interface between the application program and the operating system, and coordinates input and output to and from the simulation hardware. The Supervisor also performs various utility functions as required by a simulation application program.

Cleveland, J. I., II↗

Development of an Optical Slice for an RF and Optical Software Defined Radio

A key component in the Integrated Radio and Optical Communications project at the National Aeronautics and Space Administration's (NASA) Glenn Research Center (GRC) is the radio frequency (RF) and optical software defined radio (SDR). A NASA RF SDR might consist of a general purpose processor to run the Space Telecommunications Radio System (STRS) Architecture for radio command and control, a reconfigurable signal processing device such as a field programmable gate array (FPGA) which houses the waveform, and a digital to analog converter for (DAC) transmitting data. Prior to development, SDR architecture trades on how to combine the RF and optical elements were studied. A modular architecture with physically separate RF and optical hardware slices was chosen and the optical slice of an SDR was designed and developed. The Harris AppSTAR("TM") platform, which consists of an FPGA processing platform with a mezzanine card targeted for RF communications, was used as the base platform in prototyping the optical slice. A serially concatenated pulse position modulation (SCPPM) optical waveform was developed. The waveform follows the standard described in the Consultative Committee for Space Data Systems (CCSDS) Optical Communions Coding and Synchronization Red Book. A custom optical mezzanine printed circuit board card was developed at NASA GRC for optical transmission. The optical mezzanine card replaces the DAC, which is used in the transmission of RF signals. This paper describes RF and optical SDR architecture trades, the Harris AppSTAR("TM") platform, the design of the SCPPM waveform, and the development of the optical mezzanine card.

optical communications↗

Development of an Optical Slice for an RF and Optical Software Defined Radio

A key component in the Integrated Radio and Optical Communications project at the National Aeronautics and Space Administration's (NASA) Glenn Research Center (GRC) is the radio frequency (RF) and optical software defined radio (SDR). A NASA RF SDR might consist of a general purpose processor to run the Space Telecommunications Radio System (STRS) Architecture for radio command and control, a reconfigurable signal processing device such as a field programmable gate array (FPGA) which houses the waveform, and a digital to analog converter (DAC) for transmitting data. Prior to development, SDR architecture trades on how to combine the RF and optical elements were studied. A modular architecture with physically separate RF and optical hardware slices was chosen and the optical slice of an SDR was designed and developed. The Harris AppSTARTM platform, which consists of an FPGA processing platform with a mezzanine card targeted for RF communications, was used as the base platform in prototyping the optical slice. A serially concatenated pulse position modulation (SCPPM) optical waveform was developed. The waveform follows the standard described in the Consultative Committee for Space Data Systems (CCSDS) Optical Communications Coding and Synchronization Red Book. A custom optical mezzanine printed circuit board card was developed at NASA GRC for optical transmission. The optical mezzanine card replaces the DAC, which is used in the transmission of RF signals. This paper describes RF and optical SDR architecture trades, the Harris AppSTAR platform, the design of the SCPPM waveform, and the development of the optical mezzanine card.

Nappier, Jennifer M.↗