Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data bias”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Calibration and Performance of the ICARUS Detector at Fermilab

ICARUS is the largest Liquid Argon Time Projection Chamber (LArTPC) in operation and serves as the Far Detector of the Short Baseline Neutrino (SBN) program at Fermilab. Precise detector calibration is essential for reliable energy reconstruction and for maximizing the physics reach of the experiment. In this talk, I will describe the energy and timing calibration procedures developed at ICARUS. Thanks to the abundant flux of cosmic ray muons at the surface, the TPC response to ionization charge has been equalized across the detector, removing non-uniformities and in-transparency effects. A novel data-driven procedure has been used to tune the simulation of ionization signals and electronics noise yielding close agreement between Monte Carlo and data with minimal residual bias in reconstructed charge. In addition, the light detection system has been calibrated to sub-nanosecond timing resolution. This precision enables efficient cosmic background rejection and accurate synchronization of neutrino interactions with the time structure of both the Booster Neutrino Beam (BNB) and Neutrinos at the Main Injector (NuMI) beam. Together, these efforts demonstrate the robust performance of the detector and provide critical experience for future large LArTPCs, such as DUNE.

Vicenzi, Matteo [Brookhaven]↗
NASA NTRS1974

C-band station coordinate determination for the Geos-C altimeter calibration area

Dynamical orbital techniques were employed to estimate the center-of-mass station coordinates of six C-band radars located in the designated primary Geos-C radar altimeter calibration area. This work was performed in support of the planned Geos-C mission (December 1974 launch). The sites included Bermuda, Grand Turk, Antigua, Wallops Island (Virginia), and Merritt Island (Florida). Two sites were estimated independently at Wallops Island yielding better than 40 cm relative height recovery, with better than 10 cm and 1m (relative) recovery for phi and lambda, respectively. The tracking data used in this analysis were taken during 1969 when the radars tracked the Geos-II transponder. In all, over 120 passes of data were used. Range biases were estimated. Error analysis and comparisons with other investigators indicate that better than 2m (1 sigma) relative recovery has been achieved at all sites.

Klosko, S. M.↗
NASA NTRS1979

Modeling of the geosynchronous plasma environment

An analytic simulation of the geosynchronous environment in terms of local time and the daily A sub P index is presented. The simulation is compared with actual statistical data from approximately 50 days of ATS 5 plasma data and 50 days of ATS 6 plasma data. At low levels of activity the model adequately simulates the local time variations of the plasma parameters. At high values of geomagnetic activity, the predicted magnitudes of the plasma parameters agree with the statistical results but the effects of multiple injections are evident in both the data and the simulation, biasing the local time variations.

Garrett, H. B.↗
NASA NTRS1979

Evaluation and analysis of Seasat-A scanning multichannel Microwave Radiometer (SMMR) Antenna Pattern Correction (APC) algorithm

The brightness temperature data produced by the SMMR final Antenna Pattern Correction (APC) algorithm is discussed. The algorithm consisted of: (1) a direct comparison of the outputs of the final and interim APC algorithms; and (2) an analysis of a possible relationship between observed cross track gradients in the interim brightness temperatures and the asymmetry in the antenna temperature data. Results indicate a bias between the brightness temperature produced by the final and interim APC algorithm.

Kitzis, J. L.↗
NASA NTRS1981

Prospects for TLRS baseline accuracies in the western USA

One of the main goals of the LAGEOS satellite mission is the detection of regional geotectonic movements. A parametric study with the intention to obtain the optimal baseline precision from dynamic solutions of laser ranging to LAGEOS is presented. The varied parameters are: length of reduced arc, number of tracking stations, data noise and rate, biases, refraction errors, system efficiency, gravity model errors in the value of GM. The baseline precisions are 1-10 cm depending upon the set of parameters adopted. General principles obtained are also presented.

Christodoulidis, D.↗
NASA NTRS1981

Magnetic fields and charged particles around major planets and their satellites

It is noted that whereas Jupiter and Saturn have magnetospheres whose large-scale structure can be understood by analogy with earth, the ways in which the magnetospheres differ are of great interest. At earth, large-scale processes are dominated by convective flows of plasma driven by the solar wind. At Jupiter, centrifugal effects that are driven by planetary rotation are critical. Magnetic particle sources include not only the ionosphere and solar wind (as at earth) but also satellites and rings. The internal planetary magnetic moments controlling the scale of the magnetosphere differ by orders of magnitude between Jupiter and earth. It is pointed out that where the magnetic moments have been modeled from spacecraft data, the restricted spatial sampling has biased the results and limited confidence in details of the models. Voyager data suggest that Io may itself be magnetized and surrounded by an entirely unfamiliar type of magnetosphere.

Kivelson, M. G.↗
NASA NTRS1982

Seasat altimeter timing bias estimation

A technique developed for the solution of time lag bias based on the analysis of sea surface height discrepancies at ground track intersections, prompted by the presence of a time calibration bias in Seasat altimeter data that produced measurement errors in excess of 1 m, is shown to yield a separation of the dominant, once-per-revolution ephemeris error amounting to about 1.5 m rms from the timing error signature. The technique does not depend on precise geoid data, and in application to a global Seasat altimeter data set covering July 28-August 9, 1978, has yielded a time lag value of -81.0 + or - 2 msec. This corroborates the -79.4 msec revised value derived from a reexamination of internal instrument time delays.

Marsh, J. G.↗
NASA NTRS1982

Measurements of the properties of solar wind plasma relevant to studies of its coronal sources

Interplanetary measurements of the speeds, densities, abundances, and charge states of solar wind ions are diagnostic of conditions in the source region of the solar wind. The absolute values of the mass, momentum, and energy fluxes in the solar wind are not known to an accuracy of 20%. The principal limitations on the absolute accuracies of observations of solar wind protons and alpha particles arise from uncertain instrument calibrations, from the methods used to reduce the data, and from sampling biases. Sampling biases are very important in studies of alpha particles. Instrumental resolution and measurement ambiguities are additional major problems for the observation of ions heavier than helium. Progress in overcoming some of these measurement inadequacies is reviewed.

Neugebauer, M.↗
NASA NTRS1984

Shuttle payload dynamic environments - Update

This paper represents a brief summary of a report titled, 'Shuttle Payload Bay Dynamic Environments Summary and Conclusion Report' prepared by the Jet Propulsion Laboratory for the NASA Office of Aeronautics and Space Technology (OAST). The report provides a summary of the dynamic environmental data taken during the first five Space Shuttle flights. The present paper is concerned with a brief synopsis of the report's acoustic and high frequency data evaluation, taking into account also an example acoustic prediction method. Attention is given to an acoustic data summary, a vibration data summary, environmental uncertainties, data reduction errors, spatial bias errors, payload effects, spatial variation, flight to flight variation, payload prediction, and an example prediction.

Oconnell, M.↗
NASA NTRS1982

Computer program for post-flight evaluation of the control surface response for an attitude controlled missile

A FORTRAN IV coded computer program is presented for post-flight analysis of a missile's control surface response. It includes preprocessing of digitized telemetry data for time lags, biases, non-linear calibration changes and filtering. Measurements include autopilot attitude rate and displacement gyro output and four control surface deflections. Simple first order lags are assumed for the pitch, yaw and roll axes of control. Each actuator is also assumed to be represented by a first order lag. Mixing of pitch, yaw and roll commands to four control surfaces is assumed. A pseudo-inverse technique is used to obtain the pitch, yaw and roll components from the four measured deflections. This program has been used for over 10 years on the NASA/SCOUT launch vehicle for post-flight analysis and was helpful in detecting incipient actuator stall due to excessive hinge moments. The program is currently set up for a CDC CYBER 175 computer system. It requires 34K words of memory and contains 675 cards. A sample problem presented herein including the optional plotting requires eleven (11) seconds of central processor time.

Knauber, R. N.↗
NASA NTRS1987

An eigensystem realization algorithm using data correlations (ERA/DC) for modal parameter identification

A modification to the Eigensystem Realization Algorithm (ERA) for modal parameter identification is presented in this paper. The ERA minimum order realization approach using singular value decomposition is combined with the philosophy of the Correlation Fit method in state space form such that response data correlations rather than actual response values are used for modal parameter identification. This new method, the ERA using data correlations (ERA/DC), reduces bias errors due to noise corruption significantly without the need for model overspecification. This method is tested using simulated five-degree-of-freedom system responses corrupted by measurement noise. It is found for this case that, when model overspecification is permitted and a minimum order solution obtained via singular value truncation, the results from the two methods are of similar quality.

Juang, Jer-Nan↗
NASA NTRS1987

Punch stretching process monitoring using acoustic emission signal analysis. II - Application of frequency domain deconvolution

The coloring effect on the acoustic emission signal due to the frequency response of the data acquisition/processing instrumentation may bias the interpretation of AE signal characteristics. In this paper, a frequency domain deconvolution technique, which involves the identification of the instrumentation transfer functions and multiplication of the AE signal spectrum by the inverse of these system functions, has been carried out. In this way, the change in AE signal characteristics can be better interpreted as the result of the change in only the states of the process. Punch stretching process was used as an example to demonstrate the application of the technique. Results showed that, through the deconvolution, the frequency characteristics of AE signals generated during the stretching became more distinctive and can be more effectively used as tools for process monitoring.

Liang, Steven Y.↗
NASA NTRS1988

Laser Doppler anemometry

The material in this NASA TM is to appear as a chapter on Laser Doppler Anemometry (LDA) in the AGARDograph entitled, A Survey of Measurements and Measuring Techniques in Rapidly Distorted Compressible Turbulent Boundary Layers. The application of LDA (specifically, the dual-beam, burst-counter approach) to compressible flows is discussed. Subjects treated include signal processing, particle light scattering and tracking, data reduction and sampling bias, and three-dimensional measurements.

Johnson, Dennis A.↗
NASA NTRS1999

Epitaxial Ferroelectric Ba(0.5)Sr(0.5)TiO3 Thin Films for Room-Temperature High-Frequency Tunable Element Applications

Perovskite Ba(0.5)SR(0.5)TiO3 thin films have been synthesized on (001) LaAl03 substrates by pulsed laser ablation. Extensive X-ray diffraction, rocking curve, and pole-figure studies suggest that the films are c-axis oriented and exhibit good in-plane relationship of <100>(sub BSTO)//<100>(sub LAO). Rutherford Backscattering Spectrometry studies indicate that the epitaxial films have excellent crystalline quality with an ion beam minimum yield chi(sub min) Of only 2.6 %. The dielectric property measurements by the interdigital technique at 1 MHz show room temperature values of the relative dielectric constant, epsilon(sub r), and loss tangent, tan(sub delta), of 1430 and 0.007 with no bias, and 960 and 0.001 with 35 V bias, respectively. The obtained data suggest that the as-grown Ba(0.5)SR(0.5)TiO3 films can be used for development of room-temperature high-frequency tunable elements.

Chen, C. L.↗
NASA NTRS2000

Passive, Direct-Read Monitoring System for Selective Detection and Quantification of Hydrogen Chloride

Monitoring the exposure of an employee to hydrogen chloride or hydrochloric acid in the presence of other acids has been a challenge to the industrial hygiene community. The capability of a device to differentiate the levels of acid vapors would allow for more accurate determinations of exposure and therefore improved occupational health. In this work, a selective direct-read colorimetric badge system was validated for Short Term Exposure Limit (STEL) monitoring of hydrogen chloride. The passive colorimetric badge system consists of a direct reading badge and a color scale. The badge has a coated indicator layer with a diffusive resistance in the shape of an exclamation mark. An exclamation mark will appear if hydrogen chloride is present in the atmosphere at concentrations at or above 2.0 ppm. By using the color scale, the intensity of the color formed on the badge can be further quantified up to 25 ppm. The system was validated according to a protocol based on the NIOSH Protocol for the Evaluation of Passive Monitors. The badge was exposed to relative humidities ranging from 11% to 92%, temperatures ranging from 7 C to 400 C and air velocities ranging from 5 cm/sec to 170 cm/sec. All experiments were conducted in a laboratory vapor generation system. Hydrofluoric acid, nitric acid, sulfuric acid, chlorine, hydrogen sulfide and organic acids showed no effect on the performance of the hydrogen chloride monitoring system. The passive badge and color scale system exceeded the accuracy requirements as defined by NIOSH. At ambient conditions, the mean coefficient of variation was 10.86 and the mean bias was 1.3%. This data was presented previously at the American Industrial Hygiene Conference and Exposition in Toronto, Canada in June 1999.

Chapman, K. B.↗
NASA NTRS2000

Use of Geostationary Satellite Data to Force Land Surface Schemes within Atmospheric Mesoscale Models

A technique has been developed for assimilating GOES-derived skin temperature tendencies and insolation into the surface energy budget equation of a mesoscale model so that the simulated rate of temperature change closely agrees with the satellite observations. A critical assumption of the technique is that the availability of moisture (either from the soil or vegetation) is the least known term in the model's surface energy budget. Therefore, the simulated latent heat flux, which is a function of surface moisture availability, is adjusted based upon differences between the modeled and satellite-observed skin temperature tendencies. An advantage of this technique is that satellite temperature tendencies are assimilated in an energetically consistent manner that avoids energy imbalances and surface stability problems that arise from direct assimilation of surface shelter temperatures. The fact that the rate of change of the satellite skin temperature is used rather than the absolute temperature means that sensor calibration is not as critical. The technique has been employed on a semi-operational basis at the GHCC within the PSU/NCAR MM5. Assimilation has been performed on a grid centered over the Southeastern US since November 1998. Results from the past year show that assimilation of the satellite data reduces both the bias and RMSE for simulations of surface air temperature and relative humidity. These findings are based on comparison of assimilation runs with a control using the simple 5-layer soil model available in MM5. A significant development in the past several months was the inclusion of the detailed Oregon State University land surface model (OSU/LSM) as an option within MM5. One of our working hypotheses has been that the assimilation technique, although simple, may provide better short-term forecasts than a detailed LSM that requires significant number initialized parameters. Preliminary results indicate that the assimilation out performs the OSU/LSM as it is incorporated in MM5. Details will be presented at the symposium.

Lapenta, William M.↗
NASA NTRS1992

Rotating shift work, sleep, and accidents related to sleepiness in hospital nurses

A hospital-based survey on shift work, sleep, and accidents was carried out among 635 Massachusetts nurses. In comparison to nurses who worked only day/evening shifts, rotators had more sleep/wake cycle disruption and nodded off more at work. Rotators had twice the odds of nodding off while driving to or from work and twice the odds of a reported accident or error related to sleepiness. Application of circadian principles to the design of hospital work schedules may result in improved health and safety for nurses and patients.

Non-NASA Center↗
NASA NTRS2006

Measuring Extended Structure in Stars Using the Keck Interferometer Nuller

The Keck Interferometer Nuller is designed to detect faint off-axis mid-infrared light a few tens to a few hundreds of milliarcseconds from a bright central star. The starlight is suppressed by destructive combination along the long (85 m) baseline, which produces a fringe spacing of 25 mas at a wavelength of 10 m, with the central null crossing the position of the star. The strong, variable mid-infrared background is subtracted using interferometric phase chopping along the short (5 m) baseline. This paper presents an overview of the observing and data reduction strategies used to produce a calibrated measurement of the off-axis light. During the observations, the instrument cycles rapidly through several calibration and measurement steps, in order to monitor and stabilize the phases of the fringes produced by the various baselines, and to derive the fringe intensity at the constructive peak and destructive null along the long baseline. The data analysis involves removing biases and coherently demodulating the short-baseline fringe with the long-baseline fringe tuned to alternate between constructive and destructive phases, combining the results of many measurements to improve the sensitivity, and estimating the part of the null leakage signal which is associated with the finite angular size of the central star. Comparison of the results of null measurements on science target and calibrator stars permits the instrumental leakage - the "system null leakage" - to be removed and the off-axis light to be measured.

nulling interferometry↗