Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION PHYSICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Movable fiber probe for gas-phase laser-induced breakdown spectroscopy

A movable probe that fiber couples both the beam delivery and the signal collection functions of gas-phase laser-induced breakdown spectroscopy (LIBS) measurements was evaluated. The adjustable probe was used to investigate the effect of delivery fiber curvature on plasma characteristics and the associated effect on LIBS spectra and to further identify issues remaining to facilitate fully fiber-coupled gas-phase LIBS measurements. LIBS data were collected from lean methane-air mixtures of various equivalence ratios and spectroscopically analyzed to establish the ability to determine relative fuel-air ratio. Measurements with straight delivery fiber were compared to those with the fiber curved at specific radii. Decreasing fiber radius of curvature decreased fiber transmission efficiency and reduced the spark formation probability by almost a factor of 2. For constant fiber input energy, this decreased transmission increased the percentage of failed spark formations and influenced the LIBS elemental ratio calculations. However, minimal difference was found between LIBS measurements with straight or curved fiber as long as the output energy and a constant laser beam spot diameter were maintained on the exit beam focusing lens. A significant reduction in data scatter and improved linearity were achieved by using the Balmer series H{alpha} and H{beta} hydrogen emission line ratio as a data selection criterion. Observed linear variation of H/N elemental ratio with equivalence ratio confirmed the possibility of a flexible, light-contained, fully fiber-coupled probe for remote gas-phase LIBS analysis.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Connecting Performance Analysis and Visualization to Advance Extreme Scale Computing

In the first week of January 2014 Dagstuhl hosted a Perspectives Workshop on “Connecting Performance Analysis and Visualization to Advance Extreme Scale Computing”. The event brought together two previously separate communities – from Visualization and HPC Performance Analysis – to discuss a long term joined research agenda. The goal was to identify and address the challenges in using visual representations to understand and optimize the performance of extreme-scale applications running on today’s most powerful computing systems like climate modeling, combustion, material science or astro-physics simulations.

97 MATHEMATICS AND COMPUTING↗

A Machine Learning-Genetic Algorithm (ML-GA) Approach for Rapid Optimization Using High-Performance Computing

A Machine Learning-Genetic Algorithm (ML-GA) approach was developed to virtually discover optimum designs using training data generated from multi-dimensional simulations. Machine learning (ML) presents a pathway to transform complex physical processes that occur in a combustion engine into compact informational processes. In the present work, a total of over 2000 sector-mesh computational fluid dynamics (CFD) simulations of a heavy-duty engine were performed. These were run concurrently on a supercomputer to reduce overall turnaround time. The engine being optimized was run on a low-octane (RON70) gasoline fuel under partially premixed compression ignition (PPCI) mode. A total of nine input parameters were varied, and the CFD simulation cases were generated by randomly sampling points from this nine-dimensional input space. These input parameters included fuel injection strategy, injector design, and various in-cylinder flow and thermodynamic conditions at intake valve closure (IVC). The outputs (targets) of interest from these simulations included five metrics related to engine performance and emissions. Over 2000 samples generated from CFD were then used to train an ML model that could predict these five targets based on the nine input features. A robust super learner approach was employed to build the ML model, where results from a collection of different ML algorithms were pooled together. Thereafter, a stochastic global optimization genetic algorithm (GA) was used, with the ML model as the objective function, to optimize the input parameters based on a merit function so as to minimize fuel consumption while satisfying CO and NOx emissions constraints. The optimized configuration from ML-GA was found to be very close to that obtained from a sequentially performed CFD-GA approach, where a CFD simulation served as the objective function. In addition, the overall turnaround time was (at least) 75% lower with the ML-GA approach, as the training data was generated from concurrent CFD simulations and employing the ML model as the objective function significantly accelerated the GA optimization. Finally, this study demonstrates the potential of ML-GA and high-performance computing (HPC) to reduce the number of CFD simulations to be performed for optimization problems without loss in accuracy, thereby providing significant cost savings compared to traditional approaches.

97 MATHEMATICS AND COMPUTING↗

COMOC: Three dimensional boundary region variant, programmer's manual

The three-dimensional boundary region variant of the COMOC computer program system solves the partial differential equation system governing certain three-dimensional flows of a viscous, heat conducting, multiple-species, compressible fluid including combustion. The solution is established in physical variables, using a finite element algorithm for the boundary value portion of the problem description in combination with an explicit marching technique for the initial value character. The computational lattice may be arbitrarily nonregular, and boundary condition constraints are readily applied. The theoretical foundation of the algorithm, a detailed description on the construction and operation of the program, and instructions on utilization of the many features of the code are presented.

Orzechowski, J. A.↗

Feasibility of automated dropsize distributions from holographic data using digital image processing techniques

An automated technique for measuring particle diameters and their spatial coordinates from holographic reconstructions is being developed. Preliminary tests on actual cold-flow holograms of impinging jets indicate that a suitable discriminant algorithm consists of a Fourier-Gaussian noise filter and a contour thresholding technique. This process identifies circular as well as noncircular objects. The desired objects (in this case, circular or possibly ellipsoidal) are then selected automatically from the above set and stored with their parametric representations. From this data, dropsize distributions as a function of spatial coordinates can be generated and combustion effects due to hardware and/or physical variables studied.

Feinstein, S. P.↗

Aspects of the mechanisms of smoke generation by burning materials

An investigation of smoke generation during the burning of natural and synthetic solid materials (relevant to fire safety problems), under simulated fire conditions, is presented. Smoke formation mechanisms, including flaming and nonflaming combustion, are reviewed, and the complex physical, chemical, and electrical processes, important in smoke particulate production, are identified. With reference to the smoke formation mechanisms, measured experimental data are discussed, and include effects of ventilation gas temperature, dependence on material composition, and chemical analysis of smoke particulates. Significant differences in smoke characteristics are observed between flaming and nonflaming conditions, which is attributed to specific differences in controlling mechanisms and resultant ways leading to particulate formation. The effects of polymer substrate properties and effects of additives for a given substrate on smoke properties are also discussed in terms of basic processes. It is shown that many of the measured trends can be interpreted by considering postulated mechanisms of particulate formation.

Bankston, C. P.↗

Behavior Of Evaporating Liquid Drops In Clusters

Report presents critical analysis of methods, developed for calculating behavior of evaporating liquid drops in dense and dilute clusters. Essential to understanding variety of physical and chemical phenomena occurring in combustion of sprayed fuels and in sprays used in agriculture, food industry, and painting. Presents insights on important aspects of two-phase flow.

Bellan, Josette↗

Theoretical performance of some rocket propellants containing hydrogen, nitrogen, and oxygen

Theoretical performance data including nozzle-exit temperature, specific impulse, volume specific impulse and composition, temperature, and mean molecular weight of reaction products based on frozen equilibrium and isentropic expansion are presented for 13 propellant combinations at reaction pressure of 300 pounds per square inch absolute and expansion ratio of 20.4. On basis of maximum specific impulse alone, five fuels had the following order for any given oxidant: liquid hydrogen, hydrazine, liquid ammonia, and either hydrazine hydrate or hydroxylamine. Three oxidants with a given fuel had the following order: liquid ozone, liquid oxygen, and 100-percent hydrogen peroxide.

FUELS - PHYSICAL PROPERTIES↗

Variation of pressure limits of flame propagation with tube diameter for various isooctane-oxygen-nitrogen mixtures

An investigation was made of the change in the pressure limits of flame propagation with tube diameter for various isooctane-oxygen-nitrogen mixtures. Pressure limits were measured in cylindrical glass tubes of four different inside diameters at six different oxygen-nitrogen ratios. Under the experimental conditions, flame propagation was found to be impossible in isooctane-oxygen mixtures with oxygen concentrations less than 11 to 12 percent. Critical tube diameters for flame propagation were calculated and the effect of pressure was determined and compared with the effect of pressure on quenching distance. Critical diameters were related to flame speeds for various isooctane-oxygen-nitrogen mixtures.

FUELS-PROPERTIES,PHYSICAL AND CHEMICAL↗

Ignition-delay Characteristics in Modified Open-cup Apparatus of Several Fuels with Nitric Acid Oxidants Within Temperature Range 70 to 105 Degrees F

Fluid properties and low-temperature ignition delays were obtained for approximately 90 fuel-oxidant combinations. A red fuming nitric acid containing approximately 3 percent water and 19 percent nitrogen tetroxide froze at approximately -87 degrees F and ignited several low-viscosity fuel blends of aromatic amines in triethylamine at -76 degrees F and lower. With this acid, the following average ignition delays were obtained with a blend of 30 percent o-toluidine in triethylamine: ...

FUEL SYSTEMS - ENGINES, ROCKET↗

A thermodynamic study of the turbine-propeller engine

Equations and charts are presented for computing the thrust, the power output, the fuel consumption, and other performance parameters of a turbine-propeller engine for any given set of operating conditions and component efficiencies. Included are the effects of the pressure losses in the inlet duct and the combustion chamber, the variation of the physical properties of the gas as it passes through the system, and the change in mass flow of the gas by the addition of fuel.

Pinkel, Benjamin↗

STS-75 Flight Day 12

On this twelfth day of the STS-75 mission, the flight crew, Cmdr. Andrew Allen, Pilot Scott Horowitz, Payload Cmdr. Franklin Chang-Diaz, Payload Specialist Umberto Guidoni (Italy), and Mission Specialists Jeffrey Hoffman, Maurizio Cheli (ESA) and Claude Nicollier (ESA), are shown being interviewed via satellite hookup by reporters. Cheli, through the demonstration of a simple experiment, explains a simple acceleration physics concept. Middeck Glovebox burn and combustion experiments are also shown. Earth views include Italy, other land masses, some cloud cover, a sunrise, and horizon shots.

Source record↗

Thermal Model of the Promoted Combustion Test

Flammability of metals in high pressure, pure oxygen environments, such as rocket engine turbopumps, is commonly evaluated using the Promoted Combustion Test (PCT). The PCT emphasizes the ability of an ignited material to sustain combustion, as opposed to evaluating the sample's propensity to ignite in the first place. A common arrangement is a rod of the sample material hanging in a chamber in which a high pressure, pure oxygen environment is maintained. An igniter of some energetically combusting material is fixed to the bottom of the rod and fired. This initiates combustion, and the sample burns and melts at its bottom tip. A ball of molten material forms, and this ball detaches when it grows too large to be supported by surface tension with the rod. In materials which do not sustain combustion, the combustion then extinguishes. In materials which do sustain combustion, combustion re-initiates from molten residue left on the bottom of the rod, and the melt ball burns and grows until it detaches again. The purpose of this work is development of a PCT thermal simulation model, detailing phase change, melt detachment, and the several heat transfer modes. Combustion is modeled by a summary rate equation, whose parameters are identified by comparison to PCT results. The sensitivity of PCT results to various physical and geometrical parameters is evaluated. The identified combustion parameters may be used in design of new PCT arrangements, as might be used for flammability assessment in flow-dominated environments. The Haynes 214 nickel-based superalloy, whose PCT results are applied here, burns heterogeneously (fuel and oxidizer are of different phases; combustion takes place on the fuel surface). Heterogeneous combustion is not well understood. (In homogeneous combustion, the metal vaporizes, and combustion takes place in an analytically treatable cloud above the surface). Thermal modeling in heterogeneous combustion settings provides a means for linking test results more directly to detailed combustion mechanics, leading to improved data analysis, and improved understanding of heterogeneous combustion phenomena.

Jones, Peter D.↗

Catalyzed Ignition of Bipropellants in Microtubes

This paper addresses the need to understand the physics and chemistry involved in propellant combustion processes in micro-scale combustors for propulsion systems on micro-spacecraft. These spacecraft are planned to have a mass less than 50 kilograms with attitude control estimated to be in the 10 milli-Newton thrust class. These combustors are anticipated to be manufactured using Micro Electrical Mechanical Systems (MEMS) technology and are expected to have diameters approaching the quenching diameter of the propellants. Combustors of this size are expected to benefit significantly from surface catalysis processes. Miniature flame tube apparatus is chosen for this study because microtubes can be easily fabricated from known catalyst materials and their simplicity in geometry can be used in fundamental simulations to more carefully characterize the measured heat transfer and pressure losses for validation purposes. Experimentally, we investigate the role of catalytically active surfaces within 0.4 and 0.8 mm internal diameter micro-tubes, with special emphases on ignition and extinction processes in fuel rich gaseous hydrogen and gaseous oxygen. Flame thickness and reaction zone thickness calculations predict that the diameters of our test apparatus are below the quenching diameter of the propellants in sub-atmospheric tests. Temperature and pressure rises in resistively heated platinum and palladium micro-tubes are used as an indication of exothermic reactions. Specific data on mass flow versus preheat temperature required to achieve ignition are presented.

Schneider, Steven J.↗

The Microgravity Science Glovebox (MSG), a Resource for Gravity-Dependent Phenomena Research on the International Space Station (ISS)

The Microgravity Science Glovebox (MSG) is a double rack facility aboard the International Space Station (ISS) designed for gravity-dependent phenomena investigation handling. The MSG has been operating in the ISS US Laboratory Module since July 2002. The MSG facility provides an enclosed working area for investigation manipulation and observation in the ISS. The MSG s unique design provides two levels of containment to protect the ISS crew from hazardous operations. Research investigations operating inside the MSG are provided a large 255 liter work volume, 1000 watts of dc power via a versatile supply interface (120,28, +/-12, and 5 Vdc), 1000 watts of cooling capability, video and data recording and real time downlink, ground commanding capabilities, access to ISS Vacuum Exhaust and Vacuum Resource Systems, and gaseous nitrogen supply. With these capabilities, the MSG is an ideal platform for research required to advance the technology readiness levels (TRL) needed for the Crew Exploration Vehicle and the Exploration Initiative. Areas of research that will benefit from investigations in the MSG include thermal management, fluid physics, spacecraft fire safety, materials science, combustion and reacting control systems, in situ fabrication and repair, and advanced life support technologies. This paper will provide a detailed explanation of the MSG facility, a synopsis of the research that has already been accomplished in the MSG, an overview of investigations planning to operate in the MSG, and possible augmentations that can be added to the MSG facility to further enhance the resources provided to investigations.

Spivey, Reggie A.↗

The Microgravity Science Glovebox (MSG), a Resource for Gravity-Dependent Phenomena Research on the International Space Station (ISS)

The Microgravity Science Glovebox (MSG) is a double rack facility aboard the International Space Station (ISS) designed for gravity-dependent phenomena investigation handling. The MSG has been operating in the ISS US Laboratory Module since July 2002. The MSG facility provides an enclosed working area for investigation manipulation and observation in the ISS. The MSG's unique design provides two levels of containment to protect the ISS crew from hazardous operations. Research investigations operating inside the MSG are provided a large 255 liter work volume, 1000 watts of dc power via a versatile supply interface (120,28, plus or minus 12, and 5 Vdc), 1000 watts of cooling capability, video and data recording and real time downlink, ground commanding capabilities, access to ISS Vacuum Exhaust' and Vacuum Resource 'Systems, and gaseous nitrogen supply. With these capabilities, the MSG is an ideal platform for research required to advance the technology readiness levels (TRL) needed for the Crew Exploration Vehicle and the Exploration Initiative. Areas of research that will benefit from investigations in the MSG include thermal management, fluid physics, spacecraft fire safety, materials science, combustion and reacting control systems, in situ fabrication and repair, and advanced life support technologies. This paper will provide a detailed explanation of the MSG facility, a synopsis of the research that has already been accomplished in the MSG, an overview of investigations planning to operate in the MSG, and possible augmentations that can be added to-the MSG facility to further enhance the resources provided to investigations.

Spivey, Reggie A.↗

An Overview of the Microgravity Science Glovebox (MSG) Facility, and the Gravity-Dependent Phenomena Research Performed in the MSG on the International Space Station (ISS)

The Microgravity Science Glovebox (MSG) is a double rack facility aboard the International Space Station (ISS) designed for gravity-dependent phenomena investigation handling. The MSG has been operating in the ISS US Laboratory Module since July 2002. The MSG facility provides an enclosed working area for investigation manipulation and observation, The MSG's unique design provides two levels of containment to protect the ISS crew from hazardous operations. Research investigations operating inside the MSG are provided a large 255 liter work volume, 1000 watts of dc power via a versatile supply interface (120, 28, +/-12, and 5 Vdc), 1000 watts of cooling capability, video and data recording and real time downlink, ground commanding capabilities, access to ISS Vacuum Exhaust and Vacuum Resource Systems, and gaseous nitrogen supply. With these capabilities, the MSG is an ideal platform for research required to advance the technology readiness levels (TRL) needed for the Crew Exploration Vehicle and the Exploration Initiative. Areas of research that will benefit from investigations in the MSG include thermal management, fluid physics, spacecraft fire safety, materials science, combustion, reaction control systems, in situ fabrication and repair, and advanced life support technologies. This paper will provide a detailed explanation of the MSG facility, a synopsis of the research that has already been accomplished in the MSG and an overview of investigations planning to operate in the MSG. In addition, this paper will address possible changes to the MSG utilization process that will be brought about by the transition to ISS as a National Laboratory.

Spivey, Reggie A.↗