Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CASTINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Search for Dark Matter Axions with CAST-CAPP

The CAST-CAPP axion haloscope, operating at CERN inside the CAST dipole magnet, has searched for axions in the 19.74 μeV to 22.47 μeV mass range. The detection concept follows the Sikivie haloscope principle, where Dark Matter axions convert into photons within a resonator immersed in a magnetic field. The CAST-CAPP resonator is an array of four individual rectangular cavities inserted in a strong dipole magnet, phase-matched to maximize the detection sensitivity. Here we report on the data acquired for 4124 h from 2019 to 2021. Each cavity is equipped with a fast frequency tuning mechanism of 10 MHz/ min between 4.774 GHz and 5.434 GHz. In the present work, we exclude axion-photon couplings for virialized galactic axions down to g aγγ = 8 × 10 –14 GeV –1 at the 90% confidence level. The here implemented phase-matching technique also allows for future large-scale upgrades.

79 ASTRONOMY AND ASTROPHYSICS↗

Corrosion evaluation of Al-Cu-Mn-Zr cast alloys in 3.5% NaCl solution

Corrosion behavior of cast Al-Cu-Mn-Zr (ACMZ) and RR350 alloys was compared to a cast 319 alloy in 3.5 wt.% NaCl. After 168 h immersion, ACMZ and RR350 alloys suffered from preferential attack adjacent to intermetallic particles decorated at grain boundaries while the attack in 319 occurred in eutectic Al-Si dendritic boundaries. Electrochemical data allowed semiquantitative comparison of alloy resistance to corrosion initiation, and ACMZ type alloys, including RR350 and three alloys with higher Cu, were considered more resistant than 319 due to the absence of deleterious Si particles. In case of 319, such Si particles presumably drove higher micro-galvanic influence to initiate and sustain Al corrosion. With lower susceptibility to corrosion initiation, ACMZ alloys should exhibit higher or at minimum similar resistance compared to cast 319.

36 MATERIALS SCIENCE↗

CAST: An Inspiring Axion Helioscope ala Sikivie

CAST is a data taking axion helioscope using a recycled LHC test magnet, CERN's detector technology and cryogenics expertise. An imaging X-ray telescope improves substantially the detection sensitivity and axion-ID. Massive axion-like particles of the Kaluza-Klein type were first introduced to explain the paradox of the hot corona, which is even hotter at locations overlying magnetic spots. This is suggesting that the CAST detection principle might be at work there, but being somehow modified and performing better. Remarkably, the density profile of the Sun allows for resonance crossing (m{sub axion}c{sup 2{approx_equal}}h{omega}{sub plasma}), which axion helioscopes are aiming to reach. The restless Sun favours this occasionally even further. Then, such processes can give rise to a chimera of converted axions or the like, making the Sun appear, within known physics, as mysterious and unpredictable as it is. CAST axion limits were used to conclude also for the hidden sector paraphotons. This is then suggestive for novel helioscopes for exotica like paraphotons, chameleons, etc. Pierre Sikivie's pioneering idea was to use a magnetic field as a catalyst to transform particles from the dark sector to ours, and vice versa.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Importance of microstructural features in mechanical response of cast-cured HMX formulations

We report that cast-cure formulations of plastic-bonded explosives (PBX) present some advantages in manufacturing and application compared to traditional pressed slurry formulated materials. For example, these formulations can be cast to specific shapes and then cured in place, avoiding the need for machining precision parts. However, the microstructure of these materials can be greatly affected by the specific manufacturing process. Here, we evaluate the effect of minor changes to the formulation and manufacturing process on several cyclotetramethylene-tetranitramine (HMX) PBXs. The binders were based on hydroxyl-terminated polybutadiene (HTPB) and cast-cured using diphenylmethane diisocyanate (isonate) as a curing agent. We examined the materials using X-ray computed tomography (CT) imaging and uniaxial compression testing. The isonate content was found to significantly affect the modulus and strength of the binder. The presence of significant void content could be controlled by adding a centrifuging step during the curing process, but the resulting effect on mechanical properties was relatively minor. Finally, mesoscale simulations showed that differences in the mechanical strength of the binder were not sufficient to describe the differences observed in mechanical testing, indicating that the HMX-binder adhesion was also being changed by the manufacturing process.

36 MATERIALS SCIENCE↗

Microstructural stability and mechanical properties of the as-cast and heat-treated newly developed TiNbCrTa refractory complex concentrated alloy

In this study, a TiNbCrTa refractory complex concentrated alloy (RCCA) was prepared using vacuum arc remelting. The microstructural evolution and mechanical properties of both as-cast and heat-treated RCCA samples were analyzed. Heat treatment (HT) was performed at 800–1200 °C for 1 h in a vacuum-sealed environment. These samples exhibited a formation of Cr 2 Nb and Cr 2 Ti Laves phases. A variation in elemental distribution was observed, with interdendritic (ID) regions showing higher fractions of Ti and Cr, while the dendritic regions had a greater concentration of Ta and Nb. Micro-segregation at the IDs was confirmed through energy dispersive x-ray spectroscopy mapping, which inferred the formation of Cr- and Ti-rich phases during HT at 800–1200 °C. High-temperature HT at 1200 °C for 1 h led to the evolution of the hcp omega phase. Prolonged HT at 1200 °C for 96 h resulted in the evolution of a Cr-rich Laves phase (Cr 2 Ta), which was homogeneously distributed within the microstructure, indicating an unstable microstructure. Furthermore, despite prolonged HT, a variation in the elemental distribution persisted due to the presence of dendritic and ID regions. Electron backscattered diffraction analysis revealed the presence of bcc and hcp phases in the dendritic and ID regions, respectively, of the as-cast and HTed samples. The as-cast samples demonstrated a high compressive strength of approximately 2 GPa. Micro-hardness values increased with the HT temperature up to 1000 °C. Further increases under HT conditions did not significantly reduce the microhardness value, whereas prolonged HT at 1200 °C led to an increase in the microhardness value. Overall, the newly developed TiNbCrTa RCCA exhibited high-strength behavior even after the phase transformation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Temperature-dependent thermal expansion of cast and hot-pressed LAST (Pb-Sb-Ag-Te) thermoelectric materials

The thermal expansion for two compositions of cast and hot-pressed LAST (Pb Sb Ag Te) n-type thermoelectric materials has been measured between room temperature and 673K via thermomechanical analysis (TMA). In addition, using high-temperature X-ray diffraction (HT-XRD), the thermal expansion for both cast and hot-pressed LAST materials was determined from the temperature-dependent lattice parameters measured between room temperature and 623 K. The TMA and HT-XRD determined values of the coefficient of thermal expansion (CTE) for the LAST compositions ranged between 20106K1 and 24106K1, which is comparable to the CTE values for other thermoelectric materials including PbTe and Bi2Te3. The CTE of the LAST specimens with a higher Ag content (Ag0.86Pb19Sb1.0Te20) exhibited a higher CTE value than that of the LAST material with a lower Ag content (Ag0.43Pb18Sb1.2Te20). In addition, a peak in the temperature-dependent CTE was observed between room temperature and approximately 450K for both the cast and hot-pressed LAST with the Ag0.86Pb19Sb1.0Te20 composition, whereas the CTE of the Ag0.43Pb18Sb1.2Te20 specimen increased monotonically with temperature.

36 MATERIALS SCIENCE↗

The pathfinder X-Ray axion telescope for the International Axion Observatory (IAXO) and axion searches at the CERN Axion Solar Telescope (CAST)

The axion, a hypothetical pseudo-scalar particle proposed by Peccei and Quinn to resolve the strong CP problem in quantum chromodynamics, remains one of the most compelling dark matter candidates. Axions and Axion-Like Particles (ALPs) are characterized by a broad and largely unconstrained parameter space in mass and coupling strength, motivating extensive experimental searches. The International Axion Observatory (IAXO) is a next-generation axion helioscope designed to achieve over an order of magnitude improvement in sensitivity to the axion-photon coupling constant gaγ relative to previous experiments such as the CERN Axion Solar Telescope (CAST). IAXO will employ large-scale superconducting magnets, precision x-ray optics, and ultra-low-background detectors to search for solar axions produced primarily via the Primakoff effect. This work presents the design and performance of the IAXO pathfinder x-ray optic, a technological demonstrator that validated the optical concepts for IAXO through axion searches at CAST. Comprehensive ray-tracing simulations and experimental measurements were conducted to assess the optic's effective area, detection efficiency, and background suppression capabilities. Deployed at CAST in conjunction with Micromegas and GridPix detectors, the Pathfinder demonstrated record-setting sensitivity to both gaγ and the axion-electron coupling gae, establishing the most stringent laboratory constraints on solar axions to date. These results confirm the viability of the IAXO optical design and detector concept, providing a critical technological benchmark that informs the ongoing development of the BabyIAXO and full-scale IAXO telescopes.

47 OTHER INSTRUMENTATION↗

Comparison of dielectric properties of additively manufactured vs. solvent cast polyimide dielectrics

The permittivity, dielectric loss, and DC dielectric breakdown strength of additively manufactured, solvent-cast, and commercial polyimide films are reported As expected, commercial films performed better than both AM and solvent-cast lab-made films. Solvent-cast films generally performed better than AM films, although performance depended on the optimization of the material for the specific deposition technique. The most significant degradation of performance in all the lab-made films was in the dispersion of both the x/Df measurements and the dielectric breakdown strength (Weibull β). Commercial films had a breakdown strength of 4891 kV/cm and β = 13.0 whereas the highest performing lab-made films had a breakdown strength of 4072 kV/cm and β = 3.8. Furthermore, this increase in dispersion in all the lab-made samples is attributed to higher variability in the preparation, a higher defect level related to fabrication in the lab environment and, for some AM samples, to morphology/topology features resulting from the deposition technique.

36 MATERIALS SCIENCE↗

Hanford's Simulated Low Activity Waste Cast Stone Processing

Cast Stone is undergoing evaluation as the supplemental treatment technology for Hanford’s (Washington) high activity waste (HAW) and low activity waste (LAW). This report will only cover the LAW Cast Stone. The programs used for this simulated Cast Stone were gradient density change, compressive strength, and salt waste form phase identification. Gradient density changes show a favorable outcome by showing uniformity even though it was hypothesized differently. Compressive strength exceeded the minimum strength required by Hanford and greater compressive strength increase seen between the uses of different salt solution The salt waste form phase is still an ongoing process as this time and could not be concluded.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Engineering scale demonstration of a prospective Cast Stone process

This report documents an engineering-scale demonstration with non-radioactive simulants that was performed at SRNL using the Scaled Continuous Processing Facility (SCPF) to fill an 8.5 ft container with simulated Cast Stone grout. The Cast Stone formulation was chosen from the previous screening tests. Legacy salt solution from previous Hanford salt waste testing was adjusted to correspond to the average composition generated from the Hanford Tank Waste Operation Simulator (HTWOS). The dry blend materials, ordinary portland cement (OPC), Class F fly ash, and ground granulated blast furnace slag (GGBFS or BFS), were obtained from Lafarge North America in Pasco, WA. Over three days, the SCPF was used to fill a 1600 gallon container, staged outside the facility, with simulated Cast Stone grout. The container, staged outside the building approximately 60 ft from the SCPF, was instrumented with x-, y-, and z-axis thermocouples to monitor curing temperature. The container was also fitted with two formed core sampling vials. For the operation, the targeted grout production rate was 1.5 gpm. This required a salt solution flow rate of approximately 1 gpm and a premix feed rate of approximately 580 lb/h. During the final day of operation, the dry feed rate was increased to evaluate the ability of the system to handle increased throughput. Although non-steady state operational periods created free surface liquids, no bleed water was observed either before or after operations. The final surface slope at a fill height of 39.5 inches was 1-1.5 inches across the 8.5 foot diameter container, highest at the final fill point and lowest diametrically opposed to the fill point. During processing, grout was collected in cylindrical containers from both the mixer discharge and the discharge into the container. These samples were stored in a humid environment either in a closed box proximal to the container or inside the laboratory. Additional samples collected at these sampling points were analyzed for rheological properties and density. Both the rheological properties (plastic viscosity and yield strength) and density were consistent with previous and later SCPF runs.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Fan Fuel Casting Final Report

LANL was approached to provide material and design guidance for a fan-shaped fuel element. A total of at least three castings were planned. The first casting is a simple billet mold to be made from high carbon DU-10Mo charge material. The second and third castings are for optimization of the actual fuel plate mold. The experimental scope for optimization is only broad enough for a second iteration of the mold design. It is important to note that partway through FY17, this project was cancelled by the sponsor. This report is being written in order to capture the knowledge gained should this project resume at a later date.

42 ENGINEERING↗

Prototyping and Manufacturing of Magnetic Gearbox Components using Innovations in Castings

This project combines additive manufacturing with the broadly deployed practice of metal casting. Combining these methods will unlock new design possibilities while reducing the economic burden of early stage prototyping while leveraging well established high throughput sand casting. Two main approaches are evaluated: direct printing of single use sand molds and printing of reusable impression patterns used to create sand molds. Reusable impression molds typically can be used to produce hundreds to several thousands of casting thereby amplifying the function of the 3D printed replica mold. Emrgy’s newly developed and tested proprietary magnetic gearbox system for low head hydroelectricity generation was the subject part of this study. Leveraging ORNL’s additive manufacturing capability and expertise, a pattern impression was produced and used to create multiple sand molds of the gearbox during phase 1. Even before considering the cost savings possible once rigging and pattern mounting is optimized through repetition and improved design, final part costs using this combined method resulted in an 80% cost reduction over EMRGY’s previous method of subtractive manufacturing for gearbox production.

36 MATERIALS SCIENCE↗

Off-Gas Condensate and Cast Stone Analysis Results

A sample of off-gas condensate produced during a demonstration test of the direct-feed low-activity waste (DFLAW) Radioactive Waste Test Platform using waste retrieved from Hanford storage tank AP-105 waste was analyzed for major cations, anions, total cyanide, Resource Conservation and Recovery Act (RCRA) metals, selected radionuclides, and selected organic compounds. The remaining off-gas condensate was concentrated through evaporation and then used to produce Cast Stone waste forms. After the solid waste forms cured for 28 days, U.S. Environmental Protection Agency (EPA) Method 1311 (EPA 1992) Toxicity Characteristic Leach Procedure (TCLP) tests were conducted on two samples. The TCLP leachates were analyzed for RCRA metals, fluoride, and total cyanide. These chemical analyses were conducted to collect data on the waste form performance and to determine if the waste form will meet the disposal requirements of the Waste Control Specialists LLC (WCS) Federal Waste Disposal Facility (FWF) in Texas (WCS 2015) and the Integrated Disposal Facility at Hanford. The radionuclide results in the off-gas condensate were used to estimate concentrations in the Cast Stone waste forms; these estimates were then compared to Class C limits (30 TAC 336.362 Appendix E). With the possible exception of U-232, all measured radionuclides were determined to be below their respective Class C limits. Inductively coupled plasma-mass spectrometry (ICP-MS) was used to measure most of the radionuclides. It is not possible to differentiate the isotope measured at mass 232 between U 232 and Th-232 by mass spectroscopy. Class C limit comparisons were made by assuming two maximum possible scenarios; one in which all the isotope at mass 232 occurred as Th-232, and another assigning the entire mass contribution to U-232. If the isotope at mass 232 is all Th-232 then the waste form is well below its Class C limit; however, if the isotope at mass 232 is all U-232, then the Class C limit would be exceeded by more than a factor of 8. A chemical procedure to separate uranium from thorium followed by reanalysis by ICP-MS would be required to resolve this issue. A similar issue occurs at mass 238, which could be U-238 or Pu-238; however, in this case Pu-238 can be ruled out as a contributor to the isotope measured at mass 238 for the following reasons. Pu-238 has a half-life of 87.7 years and its daughter product (U-234) has a half-life of 2.5 × 105 years and a measured concentration of < 0.002 µg/L. If significant concentrations of Pu-238 were present in this waste, then the amount of measurable U 234 would have increased over the decades of storage in the Hanford tanks. Because this was not observed, it is concluded that the isotope measured at mass 238 is all U-238. A total of 68 organic compounds were targeted for analysis in the off-gas condensate. Of these compounds, only nine were measured above their respective minimum reportable concentration. These compounds were acenaphthene, acetone, n-butyl alcohol, p,p’-DDT, methyl ethyl ketone, nitrobenzene, o nitrophenol, pyridine, and toluene. Of the detectable compounds, only acenaphthene, acetone, o nitrophenol, and pyridine were above wastewater standards (40 CFR 268.48 - Universal Treatment Standards). None of the organic compounds exceeded the non-wastewater standards (40 CFR 268.48 - Universal Treatment Standards). Analysis of the TCLP leachates from the Cast Stone waste forms indicated that none of the analytes exceeded the Universal Treatment Standard and, in general, all were well below the standards.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Secondary Phase Objects in As-cast U-10 wt% Zr

U-10Zr castings have shown secondary phase objects when the as-cast material was examined using optical metallography and/or scanning electron microscopy. Attempts to identify these objects indicated they were rich in zirconium, but not in uranium. Exams of other U-10Zr castings in the past had indicated that these were likely Zr-carbides. Because of potential interferences in EDS spectra for carbon and uranium,a more detailed examination is necessary.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Castings and Processing of Uranium and Uranium Alloys

Presentation Outline: Production of DU Derby; DU Casting and Processing; Vacuum Induction Melting (VIM); Cast DU Microstructure / U-C(-N) Phase Diagram; Wrought DU; DU Hydro Plate and DU Specifications; Enriched Uranium; Wrought U-6Nb; Vacuum Arc-Remelting (VAR); U-6Nb Ingot Production (and Variations); Wrought Processing; U-Nb Macrostructure; Direct Cast U-6Nb; Plasma Arc Melting (PAM)

36 MATERIALS SCIENCE↗

Development of Casting Techniques for d-phase Uranium-Zirconium Alloys: CRADA 524 [Abstract only]

Casting of d-phase HALEU UZr2 alloy is an early milestone in the fabrication process for Lightbridge Fuel™. The Radiochemical Processing Laboratory at PNNL has been identified as having both the capability and expertise to perform the necessary high temperature casting of samples of Lightbridge’s alloy. The necessary equipment, facility licensing, and shipping capabilities for special nuclear material coupled with its expertise in uranium casting techniques makes PNNL uniquely suited to this project.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Cast Components for High Temperature Concentrated Solar Power Thermal Systems

Concentrating Solar-Thermal Power (CSP) components such as piping, valves fittings are required for use at temperatures up to 800°C. These are anticipated to be made using Nickel-based alloys such as Haynes ® 230 ® , Haynes ® 282 ® , or IN ® 740H ® and can contribute significantly to the cost of a CSP Gen 3 plant. Thus, there is a significant motivation to lower the cost of materials and components so that the capital costs can be minimized. In all these cases, the cost of the component has two contributions: 1. Materials cost, and 2. Manufacturing cost. Both materials cost and manufacturing costs must be kept low to attain the lowest possible cost. Materials cost can be lowered by using materials that have the ideal combination of properties at the lowest cost. Another avenue to lower cost is chose a manufacturing process that has the potential to lower the cost. Traditionally tubes are made from billets through a wrought process and can be expensive. An alternative process to consider is the centrifugal casting process where the tube is directly fabricated from molten metal. In this case, the molten metal is poured inside a cylindrical metallic mold with an insulating layer and is spun rapidly. A wide range of sizes (diameter, wall thickness, and length) can be cast using this process. The objective of this project was to develop the process for fabricating pipes and related components using a centrifugal casting process and to measure the properties of alloys fabricated using this process.

14 SOLAR ENERGY↗

Evaluation of the Mechanical Properties of Cast and Wrought CF8C-Plus Relevant to ASME Code Case Qualification

The mechanical behavior of a cast form of an advanced austenitic stainless steel, CF8C-Plus, is compared with that of its wrought equivalent in terms of both tensile and creep-rupture properties and estimated allowable stress values for pressurized service at temperatures up to about 850°C. A traditional Larson-Miller parametric model is used to analyze the creep-rupture data and to predict long-term lifetimes for comparison of the two alloy types. The cast CF8C-Plus exhibited lower yield and tensile strengths, but higher creep strength compared to its wrought counterpart. Two welding methods, shielded-metal-arc welding (SMAW) and gas-metal-arc welding, met the weld qualification acceptance criteria in ASME BPVC Section IX for the cast CF8C-Plus. However, for the wrought CF8C-Plus, while SMAW and gas-tungsten-arc welding passed the tensile acceptance criteria, they failed the side bend tests due to lack of fusion or weld metal discontinuities.

Chen, Xiang↗