SEARCH · Engineering Papers

Results for “Attack localization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Phase Transfer‐Mediated Degradation of Ether‐Based Localized High‐Concentration Electrolytes in Alkali Metal Batteries

Abstract Localized high‐concentration electrolytes (LHCEs) have attracted interest in alkali metal batteries due to the advantages of forming stable solid‐electrolyte interphases (SEIs) on anodes and good chemical/electrochemical stability. Herein, a new degradation mechanism is revealed for ether‐based LHCEs that questions their compatibility with alkali metal anodes (Li, Na, and K). Specifically, the ether solvent reacts with alkali metals to generate solvated electrons (e s − ) that attack hydrofluoroether co‐solvents to form a series of byproducts. The ether solvent essentially acts as a phase‐transfer reagent that continuously transfers electrons from solid‐phase metals into the solution phase, thus inhibiting the formation of stable SEI and leading to continuous alkali metal corrosion. Switching to an ester‐based solvating solvent or intercalation anodes such as graphite or molybdenum disulfide has been shown to avoid such a degradation mechanism due to the absence of e s − .

Chen, Xiaojuan↗

DOE OSTI2023

Influence of native oxide film on corrosion behavior of additively manufactured stainless steel 316L

The influence of the native oxide film on passive film properties and localized corrosion of additively manufactured SS 316L was studied in 1 wt% HCl by XPS characterization, electrochemical polarization curves, and post-test morphology analysis by SEM. Increased Cr oxidation kinetics was observed in the as-polished sample with the native oxide film resulting in formation of an overall more protective and compact film compared to the cathodically-activated sample. Electrochemical analysis showed that corrosive attack varied between dislocation cell boundaries to cell interiors depending on the initial surface state and polarization conditions. In conclusion, a corrosion mechanism is proposed to explain this variation.

36 MATERIALS SCIENCE↗

NASA NTRS1980

Aerodynamic-structural analysis of dual bladed helicopter systems

The aerodynamic and structural feasibility of the birotor blade concept is assessed. The inviscid flow field about the dual bladed rotor was investigated to determine the aerodynamic characteristics for various dual rotor blade placement combinations with respect to blade stagger, gap, and angle of attack between the two blades. The boundary layer separation on the rotors was studied and three dimensional induced drag calculations for the dual rotor system are presented. The thrust and power requirements of the rotor system were predicted. NASTRAN, employed as the primary modeling tool, was used to obtain a model for predicting in plane bending, out of plane bending, and the torsional behavior of the birotors. Local hub loads, blade loads, and the natural frequencies for the birotor configuration are discussed.

Selberg, B. P.↗

NASA NTRS1993

Transition effects on compressible dynamic stall of transiently pitching airfoils

Experimental results and analysis of the effects of boundary layer tripping on dynamic stall of a transiently pitching airfoil are presented. At low Mach numbers, the tripped airfoil exhibits qualitative similarity with the behavior of the untripped airfoil. However, the local supersonic flow at Mach numbers greater than 0.3 is significantly modified by the trip leading to vastly different shock/boundary layer interactions, dynamic stall onset and vortex formation angles. The formation of the laminar separation bubble is found to have a favorable influence in delaying dynamic stall on the untripped airfoil flow. In both Mach number regimes, the tripped flow actually stalls at slightly lower angles of attack. Further experimentation with three trips on an oscillating airfoil showed that the dynamic stall process is very sensitive to the state of the turbulence in the boundary layer. This sensitivity points to a need for finer turbulence modeling techniques for use in dynamic stall computations.

Wilder, M. C.↗

DOE OSTI2022

Securing Solar for the Grid: Extreme Control Whitepaper

Emerging standards outlining desired behaviors for Distributed Energy Resources (DER), such as IEEE 1547-2018, define several device-level control functions to regulate DER power injections/consumptions in response to locally sensed grid conditions. The ability to adjust settings of aggregations of DER with standardized embedded control functionality constitutes a mechanism which can, potentially, create undesirable or deleterious effects on the power grid. The purpose of this white paper is to highlight unintended effects stemming from improperly tuned embedded control functions in Distributed Energy Resources (DER), which could be exploited by a malicious entity as a means to attack the power grid.

14 SOLAR ENERGY↗

NASA NTRS2007

Fluorescence Visualization of Hypersonic Flow over Rapid Prototype Wind-Tunnel Models

Reentry models for use in hypersonic wind tunnel tests were fabricated using a stereolithography apparatus. These models were produced in one day or less, which is a significant time savings compared to the manufacture of ceramic or metal models. The models were tested in the NASA Langley Research Center 31-Inch Mach 10 Air Tunnel. Most of the models did not survive repeated tests in the tunnel, and several failure modes of the models were identified. Planar laser-induced fluorescence (PLIF) of nitric oxide (NO) was used to visualize the flowfields in the wakes of these models. Pure NO was either seeded through tubes plumbed into the model or via a tube attached to the strut holding the model, which provided localized addition of NO into the model s wake through a porous metal cylinder attached to the end of the tube. Models included several 2-inch diameter Inflatable Reentry Vehicle Experiment (IRVE) models and 5-inch diameter Crew Exploration Vehicle (CEV) models. Various configurations were studied including different sting placements relative to the models, different model orientations and attachment angles, and different NO seeding methods. The angle of attack of the models was also varied and the location of the laser sheet was scanned to provide three-dimensional flowfield information. Virtual Diagnostics Interface technology, developed at NASA Langley, was used to visualize the data sets in post processing. The use of calibration "dotcards" was investigated to correct for camera perspective and lens distortions in the PLIF images. Lessons learned and recommendations for future experiments are discussed.

Alderfer, D. W.↗

DOE OSTI2026

In-Situ TEM Molten Salt Corrosion

Molten salt reactors (MSRs) offer a compelling pathway for next-generation nuclear energy, with advantages in thermal efficiency, inherent safety, and flexible fuel management. Yet, halide-based molten salts introduce significant materials challenges, particularly alloy corrosion. Alloy performance in these environments ultimately depends on understanding how corrosion initiates and progresses at the nanoscale, however most existing models rely on post-exposure characterization, leaving degradation mechanisms largely inferred rather than directly observed. NiCr alloys have garnered interest in MSRs applications as the Ni-based matrix provides strength and creep resistance, while Cr content offers oxidation resistance in air. However, NiCr corrosion resistance in chloride salts has proven poor due to preferential chromium dissolution, the formation of Cr-depleted pathways, and grain-boundary attack. This work aims to directly visualize corrosion of Ni-20Cr exposed to LiCl-KCl using in-situ Transmission Electron Microscopy (TEM) to capture real-time microstructural evolution during corrosion. Experiments will be performed at ~800 °C under controlled pressure conditions while utilizing Energy-Dispersive X-ray Spectroscopy (EDS) to analyze elemental redistribution. Observation of chromium depletion fronts, associated surface restructuring, and localized chloride enrichment are expected. Ultimately, this study is expected to provide a link between microscale processes and the macroscopic degradation behaviors relevant to MSR operation in advanced reactor environments. Simultaneously, this approach enables future in-situ investigations regarding alloy composition, salt chemistry, and their influence on corrosion pathways and long-term stability.?

36 - MATERIALS SCIENCE↗

DOE OSTI2023

Mapping the intrinsic photocurrent streamlines through micromagnetic heterostructure devices

Photocurrent in quantum materials is often collected at global contacts far away from the initial photoexcitation. This collection process is highly nonlocal. It involves an intricate spatial pattern of photocurrent flow (streamlines) away from its primary photoexcitation that depends sensitively on the configuration of current collecting contacts as well as the spatial nonuniformity and tensor structure of conductivity. Direct imaging to track photocurrent streamlines is challenging. Here, we demonstrate a microscopy method to image photocurrent streamlines through ultrathin heterostructure devices comprising platinum on yttrium iron garnet (YIG). We accomplish this by combining scanning photovoltage microscopy with a uniform rotating magnetic field. Here, local photocurrent is generated through a photo-Nernst type effect with its direction controlled by the external magnetic field. This enables the mapping of photocurrent streamlines in a variety of geometries that include conventional Hall bar-type devices, but also unconventional wing-shaped devices called electrofoils. In these, we find that photocurrent streamlines display contortion, compression, and expansion behavior depending on the shape and angle of attack of the electrofoil devices, much in the same way as tracers in a wind tunnel map the flow of air around an aerodynamic airfoil. This affords a powerful tool to visualize and characterize charge flow in optoelectronic devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

NASA NTRS2020

Aeroheating Measurements of BOLT Aerodynamic Fairings and Transition Module

The Air Force Office of Scientific Research (AFOSR) has sponsored the Boundary Layer Transition (BOLT) Experiments to investigate hypersonic boundary layer transition on a low-curvature, concave surface with swept leading edges. This paper presents aeroheating measurements on a subscale model of the BOLT Flight Geometry, aerodynamic fairings, and Transition Module (TSM) in the NASA Langley 20-Inch Mach 6 Air Tunnel. The purpose of the test was to investigate and identify any areas of localized heating on the TSM for inclusion in the BOLT Critical Design Review (CDR). Surface heating distributions were measured using global phosphor thermography, and data were obtained for a range of model attitudes and free stream Reynolds numbers. Measurements showed low heating on the fairings and TSM. Additional analysis was completed after the CDR to compare heating on the TSM for the nominal BOLT vehicle reentry angle-of-attack with heating on the TSM for possible reentry angle-of-attack excursions. The results of this analysis were used in conjunction with thermal analyses from Johns Hopkins Applied Physics Lab (JHU/APL) and the Air Force Research Laboratory (AFRL) to assess the need for thermal protection on the flight vehicle TSM.

Rieken, Elizabeth F.↗

NASA NTRS1974

Experimental investigation at Mach 8 of the effects of projections and cavities on heat transfer to a model of the Viking aeroshell

An experimental investigation into the aerodynamic heating on a Mars entry vehicle shape with several types of local surface distortion is presented. The configurations tested were 0.033-scale models of a spherically blunted 70 deg half-angle cone with two protuberances of different length, representing the tube leading to the gas chromograph mass spectrometer, and two aeroshell-bioshield attachment points of different size. These models were tested at free-stream Reynolds numbers per meter of 3.7 million and 17 million over an angle-of-attack range from 0 to 18 deg in the Langley Mach 8 variable density hypersonic tunnel. The phase change-coating technique was used to measure heat transfer coefficient. The long protuberance caused more severe interference heating than the short protuberance for the same conditions. When the short projection was located close to the edge of the aeroshell, the interference heating was greater than that on the same projection when located near the vertex. A significant increase in heat transfer coefficient was measured only on the larger aeroshell-bioshield attachment point.

Creel, T. R., Jr.↗

NASA NTRS1990

Aeolian Removal of Dust Types from Photovoltaic Surfaces on Mars

Dust elevated in local or global dust storms on the Martian surface could settle on photovoltaic (PV) surfaces and seriously hamper their performance. Using a recently developed technique to apply a uniform dust layer, PV surface materials were subjected to simulated Martian winds in an attempt to determine whether natural aeolian processes on Mars would sweep off the settled dust. Three different types of dust were used. The effects of wind velocity, angle of attack, height above the Martian surface, and surface coating material were investigated. It was found that arrays mounted on an angle of attack approaching 45 deg show the most efficient clearing. Although the angular dependence is not sharp, horizontally mounted arrays required much higher wind velocities to clear off the dust. From this test it appears that the arrays may be erected quite near the ground, but previous studies have suggested that saltation effects can be expected to cause such arrays to be covered by soil if they are set up less than about a meter from the ground. Particle size effect appear to dominate over surface chemistry in these experiments, but additional tests are required to confirm this.

Gaier, James R.↗

NASA NTRS2015

Effects of Vehicle Weight and True Versus Indicated Airspeed on BVI Noise During Steady Descending Flight

Blade-vortex interaction noise measurements are analyzed for an AS350B helicopter operated at 7000 ft elevation above sea level. Blade-vortex interaction (BVI) noise from four, 6 degree descent conditions are investigated with descents flown at 80 knot true and indicated airspeed, as well as 4400 and 3915 pound take-off weights. BVI noise is extracted from the acquired acoustic signals by way of a previously developed time-frequency analysis technique. The BVI extraction technique is shown to provide a better localization of BVI noise, compared to the standard Fourier transform integration method. Using this technique, it was discovered that large changes in BVI noise amplitude occurred due to changes in vehicle gross weight. Changes in BVI noise amplitude were too large to be due solely to changes in the vortex strength caused by varying vehicle weight. Instead, it is suggested that vehicle weight modifies the tip-path-plane angle of attack, as well as induced inflow, resulting in large variations of BVI noise. It was also shown that defining flight conditions by true airspeed, rather than indicated airspeed, provides more consistent BVI noise signals.

Stephenson, James H.↗

NASA NTRS2019

Aeroelastic Indicial Response Reduced-Order Modeling for Flexible Flight Vehicles

A reduced-order modeling method capable of providing computationally efficient predictions of the nonlinear, unsteady aerodynamics encountered by flexible flight vehicles under- going forced oscillations is presented. Models are developed using indicial response theory, which characterizes a vehicle’s dynamics through identification of time-accurate aerodynamic responses due to step changes in the vehicle-state parameters, e.g., angle-of-attack, pitch rate. A coupled computational fluid dynamics aeroelastic analysis is proposed for identifying step (indicial) responses of flexible vehicles. In this approach, aeroelastic indicial responses are simulated via prescribed rigid body motions, while fluid-structure interactions are captured at the subiterative level through coupling to a linear modal structural solver. A nonlinear extension of indicial response theory is applied through time-dependent linear interpolation of a database of locally linear aeroelastic step responses. Reduced-order models are then created using the mathematical principle of convolution applied to the interpolated aeroelastic indicial responses to predict the time-dependent aerodynamic response of a flexible vehicle to any arbitrary prescribed flight maneuver. The NASA FUN3D computational fluid dynamics solver is utilized for simulating full-order trajectories and indicial response functions. Aerodynamic predictions were generated for the X-56A aircraft undergoing a series of harmonic forced oscillations. The s are shown to provide a practical option for evaluating the unsteady aerodynamics of flexible vehicles using high-fidelity simulations.

Hiller, Brett↗

NASA NTRS1981

Metal and Bi/Pb microdistribution studies of an L3 chondrite - Their implications for a meteorite parent body

Strong localizations relative to bulk are reported of Bi, and to a lesser extent Pb, in some of the kamacite grains in Khohar, while other kamacite grains show no such enrichments. Distinctive and correlated differences in the Ni content are found in the two kamacite populations, with the Bi/Pb-rich kamacite grains having consistently lower Ni levels than the 6-7% typical of the Bi/Pb-poor kamacite. The Bi/Pb-rich kamacite grains also exhibit a highly reactive attack upon etching, which may be due to a finely polycrystaline microstructure. It is concluded that the trace element microdistributions were not established in the nebula, and that the enrichments were not likely to have occurred with slow cooling in the presence of a vapor phase during the kamacite-taenite phase transitions.

Woolum, D. S.↗

NASA NTRS1998

On the Circulation Manifold for Two Adjacent Lifting Sections

The circulation functional relative to two adjacent lifting sections is studied for two cases. In the first case we consider two adjacent circles. The circulation is computed as a function of the displacement of the secondary circle along the axis joining the two centers and of the angle of attack of the secondary circle, The gradient of such functional is computed by deriving a set of elliptic functions with respect both to their argument and to their Period. In the second case studied, we considered a wing-flap configuration. The circulation is computed by some implicit mappings, whose differentials with respect to the variation of the geometrical configuration in the physical space are found by divided differences. Configurations giving rise to local maxima and minima in the circulation manifold are presented.

Zannetti, Luca↗

NASA NTRS1999

Cone-Probe Rake Design and Calibration for Supersonic Wind Tunnel Models

A series of experimental investigations were conducted at the NASA Langley Unitary Plan Wind Tunnel (UPWT) to calibrate cone-probe rakes designed to measure the flow field on 1-2% scale, high-speed wind tunnel models from Mach 2.15 to 2.4. The rakes were developed from a previous design that exhibited unfavorable measurement characteristics caused by a high probe spatial density and flow blockage from the rake body. Calibration parameters included Mach number, total pressure recovery, and flow angularity. Reference conditions were determined from a localized UPWT test section flow survey using a 10deg supersonic wedge probe. Test section Mach number and total pressure were determined using a novel iterative technique that accounted for boundary layer effects on the wedge surface. Cone-probe measurements were correlated to the surveyed flow conditions using analytical functions and recursive algorithms that resolved Mach number, pressure recovery, and flow angle to within +/-0.01, +/-1% and +/-0.1deg , respectively, for angles of attack and sideslip between +/-8deg. Uncertainty estimates indicated the overall cone-probe calibration accuracy was strongly influenced by the propagation of measurement error into the calculated results.

Won, Mark J.↗

NASA NTRS1989

Time evolution of cloud fields from ISCCP observations

The time series of 280 km regional cloud amounts to characterize the evolution of the cloud fields is presented. New observations from the International Satellite Cloud Climatology Project (ISCCP) allow use of this data to attack the problem of simulating clouds and cloud changes from purely an empirical approach. It is shown that both persistence of cloud and cloud lifetimes indicate very long time scales to 40 hours for lifetime and weeks for persistent cloud systems. The simulation of these effects in GCM's requires more than attempting to simulate the variations of individual cloud elements. The tropical regions over the oceans show shorter lifetimes because there are basically local controls to the presence of clouds.

Campbell, G. G.↗

NASA NTRSDate not supplied

Implementation and Verification of the SST-𝜸 and SA-AFT Transition Models in FUN3D

The transition modeling capability in the NASA unstructured FUN3D suite of codes has been augmented by incorporating two additional transport-equation-based transition models, namely, the 𝜸 transition model coupled with Menter’s 2003 Shear-Stress Transport (SST) turbulence model and Coder’s Amplification Factor Transport (AFT) transition model combined with the Spalart-Allmaras (SA) turbulence model. Both of these models, SST-𝜸 and SA-AFT, are used to compute transition characteristics of several test cases from the literature. The selected test cases cover a range of transition scenarios including bypass transition over a flat plate (ERCOFTAC T3A and T3A- flow configurations), transition in the presence of separation bubbles (NLF-0416 airfoil at selected angles of attack), and natural transition due to Tollmien-Schlichting instabilities (flat-plate experiment by Schubauer and Klebanoff). To address the urgent need for model verification as highlighted in recent workshops on transition modeling, the drag, lift, surface pressure, and skin-friction coefficients from the FUN3D solutions for a sequence of meshes are compared with the results obtained with the same models implemented in the NASA structured grid flow solver OVERFLOW. Comparisons between the local and global surface coefficients from the FUN3D and OVERFLOW solvers for all test cases resulted in good agreement for the finest meshes.

Verification↗