SEARCH · Engineering Papers

Results for “Approximate boundary”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Euler solutions to nonlinear acoustics of non-lifting rotor blades

For the first time a computational fluid dynamics (CFD) method is used to calculate directly the high-speed impulsive (HSI) noise of a non-lifting hovering rotor blade out to a distance of over three rotor radii. In order to accurately propagate the acoustic wave in a stable and efficient manner, an implicit upwind-biased Euler method is solved on a grid with points clustered along the line of propagation. A detailed validation of the code is performed for a rectangular rotor blade at tip Mach numbers ranging from 0.88 to 0.92. The agreement with experiment is excellent at both the sonic cylinder and at 2.18 rotor radii. The agreement at 3.09 rotor radii is still very good, showing improvements over the results from the best previous method. Grid sensitivity studies indicate that with special attention to the location of the boundaries a grid with approximately 60,000 points is adequate. This results in a computational time of approximately 40 minutes on a Cray-XMP. The practicality of the method to calculate HSI noise is demonstrated by expanding the scope of the investigation to examine the rectangular blade as well as a highly swept and tapered blade over a tip Mach number range of 0.80 to 0.95. Comparisons with experimental data are excellent and the advantages of planform modifications are clearly evident. New insight is gained into the mechanisms of nonlinear propagation and the minimum distance at which a valid comparison of different rotors can be made: approximately two rotor radii from the center of rotation.

Baeder, J. D.↗

NASA NTRS1993

Supersonic flow visualization of a nacelle in close proximity to a simulated wing

A flow visualization study was made in the 9 x 9 inch supersonic wind tunnel at Wichita State University to examine shock and boundary layer flow interaction for a nacelle in close proximity to the lower surface of a simulated wing. The test matrix included variations of angle of attack from -2 degrees to +4 degrees, nacelle-wing gap from 0.5 to 3-nacelle inlet diameter (0.12 inch), and Reynolds number based on nacelle length (1.164 inch) from 1.16 x 10(exp 6) to 1.45 x 10(exp 6) at a nominal Mach number of 2. Schlieren pictures of wing and nacelle flowfield were recorded by a video camera during each tunnel run. Results show that the nacelle inlet shock wave remains attached to the inlet lip and its impingement does not significantly affect the wing boundary layer. At the nacelle trailing edge location, the wing boundary layer thickness is approximately one nacelle inlet diameter at alpha = 0 degrees and it decreases with increase of angle of attack.

Biber, Kasim↗

NASA NTRS1994

An axisymmetric analog two-layer convective heating procedure with application to the evaluation of Space Shuttle Orbiter wing leading edge and windward surface heating

A numerical procedure for predicting the convective heating rate of hypersonic reentry vehicles is described. The procedure, which is based on the axisymmetric analog, consists of obtaining the three-dimensional inviscid flowfield solution; then the surface streamlines and metrics are calculated using the inviscid velocity components on the surface; finally, an axisymmetric boundary layer code or approximate convective heating equations are used to evaluate heating rates. This approach yields heating predictions to general three-dimensional body shapes. The procedure has been applied to the prediction of the wing leading edge heating to the Space Shuttle Orbiter. The numerical results are compared with the results of heat transfer testing (OH66) of an 0.025 scale model of the Space Shuttle Orbiter configuration in the Calspan Hypersonic Shock Tunnel (HST) at Mach 10 and angles of attack of 30 and 40 degrees. Comparisons with STS-5 flight data at Mach 9.15 and angle of attack of 37.4 degrees and STS-2 flight data at Mach 12.86 and angle of attack of 39.7 degrees are also given.

Wang, K. C.↗

NASA NTRS1994

Microwave radiative transfer through horizontally inhomogeneous precipitating clouds

Recent advances in cloud microphysical models have led to realistic three-dimensional distributions of cloud constituents. Radiative transfer schemes can make use of this detailed knowledge in order to study the effects of horizontal as well as vertical inhomogeneities within clouds. This study looks specifically at the differences between three-dimensional radiative transfer results and those obtained by plane parallel, independent pixel approximations in the microwave spectrum. A three-dimensional discrete ordinates method as well as a backward Monte Carlo method are used to calculate realistic radiances emerging from the cloud. Analyses between these models and independent pixel approximations reveal that plane parallel approximations introduce two distinct types of errors. The first error is physical in nature and is related to the fact that plane parallel approximations do not allow energy to leak out of dense areas into surrouding areas. In general, it was found that these errors are quite small for emission-dominated frequencies (37 GHz and lower) and that physical errors are highly pronounced only at scattering frequencies (85 GHz) where large deviations and biases up to 8 K averaged over the entire cloud were found. The second error is more geometric in nature and is related to the fact that plane parallel approximations cannot accommodate physical boundaries in the horizontal dimension for off-nadir viewing angles. The geometric errors were comparable in magnitude for all frequencies. Their magnitude, however, depends on a number of factors including the scheme used to deal with the edge, the nature of the surface, and the viewing angle.

Roberti, Laura↗

NASA NTRS1999

Influence of Ply Waviness on Fatigue Life of Tapered Composite Flexbeam Laminates

Nonlinear tapered flexbeam laminates, with significant ply waviness, were cut from a full-size composite rotor hub flexbeam. The specimens were tested under combined axial tension and cyclic bending loads. All of the specimens had wavy plies through the center and near the surfaces (termed marcelled areas), although for some of the specimens the surface marcels were very obvious, and for others they were much smaller. The specimens failed by first developing cracks through the marcels at the surfaces, and then delaminations grew from those cracks, in both directions. Delamination failure occurred in these specimens at significantly shorter fatigue lives than similar specimens without waviness, tested in ref. 2. A 2D finite element model was developed which closely approximated the flexbeam geometry, boundary conditions, and loading. In addition, the FE model duplicated the waviness observed in one of the test specimens. The model was analyzed using a geometrically nonlinear FE code. Modifications were made to the original model to reduce the amplitude of the marcels near the surfaces. The analysis was repeated for each modification. Comparisons of the interlaminar normal stresses, sigma(sub n), in the various models showed that under combined axial-tension and cyclic-bending loading, for marcels of the same aspect ratio, sigma(sub n) stresses increased as the distance along the taper, from thick to thin end, increased. For marcels of the same aspect ratio and at the same X-location along the taper, sigma(sub n) stresses decreased as the distance from the surface into the flexbeam interior increased. A technique was presented for determining the smallest acceptable marcel aspect ratio at various locations in the flexbeam.

Murri, Gretchen B.↗

NASA NTRS2003

Performance of Goddard Earth Observing System GCM Column Radiation Models under Heterogeneous Cloud Conditions

We test the performance of the shortwave (SW) and longwave (LW) Column Radiation Models (CORAMs) of Chou and collaborators with heterogeneous cloud fields from a global single-day dataset produced by NCAR's Community Atmospheric Model with a 2-D CRM installed in each gridbox. The original SW version of the CORAM performs quite well compared to reference Independent Column Approximation (ICA) calculations for boundary fluxes, largely due to the success of a combined overlap and cloud scaling parameterization scheme. The absolute magnitude of errors relative to ICA are even smaller for the LW CORAM which applies similar overlap. The vertical distribution of heating and cooling within the atmosphere is also simulated quite well with daily-averaged zonal errors always below 0.3 K/d for SW heating rates and 0.6 K/d for LW cooling rates. The SW CORAM's performance improves by introducing a scheme that accounts for cloud inhomogeneity. These results suggest that previous studies demonstrating the inaccuracy of plane-parallel models may have unfairly focused on worst scenario cases, and that current radiative transfer algorithms of General Circulation Models (GCMs) may be more capable than previously thought in estimating realistic spatial and temporal averages of radiative fluxes, as long as they are provided with correct mean cloud profiles. However, even if the errors of the particular CORAMs are small, they seem to be systematic, and the impact of the biases can be fully assessed only with GCM climate simulations.

Oreopoulos, L.↗

NASA NTRS2002

Fatigue Life Analysis of Tapered Hybrid Composite Flexbeams

Nonlinear-tapered flexbeam laminates from a full-size composite helicopter rotor hub flexbeam were tested under combined constant axial tension and cyclic bending loads. The two different graphite/glass hybrid configurations tested under cyclic loading failed by delamination in the tapered region. A 2-D finite element model was developed which closely approximated the flexbeam geometry, boundary conditions, and loading. The analysis results from two geometrically nonlinear finite element codes, ANSYS and ABAQUS, are presented and compared. Strain energy release rates (G) obtained from the above codes using the virtual crack closure technique (VCCT) at a resin crack location in the flexbeams are presented for both hybrid material types. These results compare well with each other and suggest that the initial delamination growth from the resin crack toward the thick region of the flexbeam is strongly mode II. The peak calculated G values were used with material characterization data to calculate fatigue life curves and compared with test data. A curve relating maximum surface strain to number of loading cycles at delamination onset compared reasonably well with the test results.

Murri, Gretchen B.↗

NASA NTRS2006

Fatigue Life Methodology for Tapered Hybrid Composite Flexbeams

Nonlinear-tapered flexbeam specimens from a full-size composite helicopter rotor hub flexbeam were tested under combined constant axial tension and cyclic bending loads. Two different graphite/glass hybrid configurations tested under cyclic loading failed by delamination in the tapered region. A 2-D finite element model was developed which closely approximated the flexbeam geometry, boundary conditions, and loading. The analysis results from two geometrically nonlinear finite element codes, ANSYS and ABAQUS, are presented and compared. Strain energy release rates (G) associated with simulated delamination growth in the flexbeams are presented from both codes. These results compare well with each other and suggest that the initial delamination growth from the tip of the ply-drop toward the thick region of the flexbeam is strongly mode II. The peak calculated G values were used with material characterization data to calculate fatigue life curves for comparison with test data. A curve relating maximum surface strain to number of loading cycles at delamination onset compared well with the test results.

urri, Gretchen B.↗

NASA NTRS2012

Magnetic Helicity and Planetary Dynamos

A model planetary dynamo based on the Boussinesq approximation along with homogeneous boundary conditions is considered. A statistical theory describing a large-scale MHD dynamo is found, in which magnetic helicity is the critical parameter

Shebalin, John V.↗

NASA NTRS2012

Surface and Flow Field Measurements on the FAITH Hill Model

A series of experimental tests, using both qualitative and quantitative techniques, were conducted to characterize both surface and off-surface flow characteristics of an axisymmetric, modified-cosine-shaped, wall-mounted hill named "FAITH" (Fundamental Aero Investigates The Hill). Two separate models were employed: a 6" high, 18" base diameter machined aluminum model that was used for wind tunnel tests and a smaller scale (2" high, 6" base diameter) sintered nylon version that was used in the water channel facility. Wind tunnel and water channel tests were conducted at mean test section speeds of 165 fps (Reynolds Number based on height = 500,000) and 0.1 fps (Reynolds Number of 1000), respectively. The ratio of model height to boundary later height was approximately 3 for both tests. Qualitative techniques that were employed to characterize the complex flow included surface oil flow visualization for the wind tunnel tests, and dye injection for the water channel tests. Quantitative techniques that were employed to characterize the flow included Cobra Probe to determine point-wise steady and unsteady 3D velocities, Particle Image Velocimetry (PIV) to determine 3D velocities and turbulence statistics along specified planes, Pressure Sensitive Paint (PSP) to determine mean surface pressures, and Fringe Imaging Skin Friction (FISF) to determine surface skin friction (magnitude and direction). This initial report summarizes the experimental set-up, techniques used, data acquired and describes some details of the dataset that is being constructed for use by other researchers, especially the CFD community. Subsequent reports will discuss the data and their interpretation in more detail

Bell, James H.↗

NASA NTRS2018

Using Adaptive Mesh Refinement to Study Grid Resolution Effects for Shock/Boundary-Layer Interactions

Adaptive Mesh Refinement (AMR) promises a much more computationally efficient meansto obtain a discrete approximation to a continuous boundary value problem of a specifiedaccuracy than classic isotropic grid refinement. The AMR capability of OVERFLOW is utilizedto provide estimates of the exact analytical solutions to problems of interest to turbulencemodeling. Predictions of surface pressure and skin friction, essentially the state of stress at thesurface, shows little difference with grids believed to be "grid resolved." Velocity profiles, on theother hand, show marked differences in flows with shocks. The AMR method, as implementedin OVERFLOW2.2k, appears to provide the ability to produce arbitrarily accurate solutionsat a predictable cost much smaller than classic uniform mesh refinement.

Adaptive Mesh Refinement↗

NASA NTRSDate not supplied

Adaptive mesh refinement and turbulence modeling

Adaptive mesh refinement is shown to be essential in turbulence modeling. Adaptive Mesh Refinement (AMR) is a more computationally efficient means to obtain a discrete approximation to a continuous boundary value problem of a specified accuracy than classic isotropic grid refinement. Previous application of this methodology in the assessment of turbulence models suggested that the field variable solution on the interior of the domain was more sensitive to grid refinement than would be suggested by the sensitivity to grid refinement of surface quantities. Revisiting challenging high speed flow field revealed that issues believed to be fundamental turbulence model issues appear to be related to an under-resolved boundary layer edge – a flow detail previously considered unimportant.

Hypersonics↗

NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration

This paper reports the results of a comprehensive linear stability analysis of the boundary layer flow over the common research model with natural laminar flow (CRM-NLF) aircraft configuration. The flow conditions match selected test conditions from a recent wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. Previous work has shown that the measured onset of laminar-turbulent transition during the experiments can be correlated with the linear amplification of Tollmien-Schlichting (TS) and stationary crossflow (CF) instabilities in the swept wing boundary layer. However, a significant scatter ( N ∈ (4,9)) was observed in the values of the logarithmic amplification factor along the measured transition front. This previous analysis was based on an approximate basic state (based on a boundary layer code with conical flow approximation) and parallel stability computations without surface curvature effects. Here, we examine the effects of these various approximations with the goal of quantifying the resulting changes in the N-factor correlations. Specifically, both linear stability theory (LST) and the parabolized stability equations (PSE)are used in conjunction with an accurate definition of the laminar boundary layer flow as computed with a Navier-Stokes solver with a Reynolds-Averaged-Navier-Stokes (RANS) based turbulence model within the turbulent parts of the flow. Furthermore, the effects of instability wave propagation within a fully three-dimensional boundary layer are also evaluated by integrating the disturbance growth rates along suitably chosen, curvilinear (i.e., nonplanar) propagation trajectories. The results of this analysis are also used in an accompanying paper by Venkatachari et al. to develop improved, physics based transition predictions for the same CRM-NLF configuration.

Boundary layer transition↗

NASA NTRS1976

Compressible laminar boundary layers with large acceleration and cooling

The paper extends an approximate prediction method involving the integral form of the momentum equation to deduce the flow quantities of interest when compressibility effects become important and heat transfer may occur. The approximate method is applicable to a two-dimensional laminar boundary layer on an impermeable surface of negligible curvature for a specified integral momentum equation. The proposed approximate method involves the use of similar solutions in conjunction with the integral momentum equation for isentropic freestream flow of a perfect gas by assuming that viscosity is proportional to stagnation condition and Prandtl number is unity. The study pertains to larger values of acceleration (acceleration parameter to 20 rather than 2) than previously considered to account for rapidly accelerating flows such as in supersonic nozzles. A discussion of some applications confirms the advantages of the method in establishing better confidence in the predictions.

Back, L. H.↗

NASA NTRS1990

Comparison of 3-D viscous flow computations of Mach 5 inlet with experimental data

A time marching 3-D full Navier-Stokes code, called PARC3D, is validated for an experimental Mach 5 inlet configuration using the data obtained in the 10 x 10 ft supersonic wind tunnel at the NASA Lewis Research Center. For the first time, a solution is obtained for this configuration with the actual geometry, the tunnel conditions, and all the bleed zones modeled in the computation. Pitot pressure profiles and static pressures at various locations in the inlet are compared with the corresponding experimental data. The effect of bleed zones, located in different places on the inlet walls, in eliminating the low energy vortical flow generated from the 3-D shock-boundary layer interaction is simulated very well even though some approximations are used in applying the bleed boundary conditions and in the turbulence model. A further detailed study of the effect of individual bleed ports is needed to understand fully the actual mechanism of efficiently eliminating the vortical flow from the inlet. A better turbulence model would help to improve the accuracy even further in predicting the corner flow boundary layer profiles.

Reddy, D. R.↗

NASA NTRS1991

Numerical simulation of transition in wall-bounded shear flows

The current status of numerical simulation techniques for the transition to turbulence in incompressible channel and boundary-layer flows is surveyed, and typical results are presented graphically. The focus is on direct numerical simulations based on the full nonlinear time-dependent Navier-Stokes equations without empirical closure assumptions for prescribed initial and boundary conditions. Topics addressed include the vibrating ribbon problem, space and time discretization, initial and boundary conditions, alternative methods based on the triple-deck approximation, two-dimensional channel and boundary-layer flows, three-dimensional boundary layers, wave packets and turbulent spots, compressible flows, transition control, and transition modeling.

Kleiser, Leonhard↗

NASA NTRS1987

Approximation techniques for domain identification in two-dimensional parabolic systems under boundary observations

The identification of the geometrical structure of the system boundary for a two-dimensional diffusion system is considered. The domain identification treated is converted into an optimization problem based on a fit-to-data criterion and theoretical convergence results for approximate identification techniques are discussed. Results of numerical experiments to demonstrate the efficiency of the theoretical ideas are reported.

Banks, H. T.↗

NASA NTRS1988

Optimal reentry guidance for aeroassisted orbit transfer vehicles

A three-state model is presented for analyzing the problem of optimal changes in heading with minimum energy loss for a hypersonic gliding vehicle. A further model order reduction to a single state model is examined using singular perturbation theory. The optimal solution for the reduced problem defines an optimal altitude profile dependent on the current energy of the vehicle. A separate boundary-layer analysis is used to account for altitude and flight path angle dynamics, and to obtain lift and bank angle control solutions. By considering alternative approximations to solve the boundary-layer problem, three guidance laws are obtained, each having a feedback form. The guidance laws are evaluated for a hypothetical vehicle, and compared to an optimal solution obtained using a multiple shooting algorithm.

Calise, Anthony J.↗