Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

LDRD 19A42-015, Multi-Wire Arc Additive Manufacturing

Additive manufacturing (AM) techniques can efficiently and cost-effectively fabricate components with both geometrical and compositional complexities, where functionally-graded compositions in a component allow multiple service requirements to be simultaneously addressed, such as corrosion and high temperature structural requirements. High cost alloy compositions need only be deposited in local areas where they are needed. A multi-wire arc additive manufacturing (m-WAAM) system was developed to enable functionally-graded, additively manufactured complex structures. The m-WAAM system utilizes multiple filler wire alloys, allowing control of composition and composition gradients in the component during additive fabrication. Ultimately, this project successfully developed a high deposition rate, arc-based, additive manufacturing process with the truly novel capability of enabling spatial composition tailoring during the build of the component. System capabilities and process science will be studied in a follow-on LDRD starting next year.

36 MATERIALS SCIENCE↗

Additive Engineering for Efficient and Stable Perovskite Solar Cells

Perovskite solar cells (PSCs) have reached a certified 25.2% efficiency in 2019 due to their high absorption coefficient, high carrier mobility, long diffusion length, and tunable direct bandgap. However, due to the nature of solution processing and rapid crystal growth of perovskite thin films, a variety of defects can form as a result of the precursor compositions and processing conditions. The use of additives can affect perovskite crystallization and film formation, defect passivation in the bulk and/or at the surface, as well as influence the interface tuning of structure and energetics. Here, recent progress in additive engineering during perovskite film formation is discussed according to the following common categories: Lewis acid (e.g., metal cations, fullerene derivatives), Lewis base based on the donor type (e.g., O-donor, S-donor, and N-donor), ammonium salts, low-dimensional perovskites, and ionic liquid. Various additive-assisted strategies for interface optimization are then summarized; additives include modifiers to improve electron- and hole-transport layers as well as those to modify perovskite surface properties. To conclude, an outlook is provided on research trends with respect to additive engineering in PSC development.

14 SOLAR ENERGY↗

Clinical Indication for Computed Tomography During Hepatic Arteriography (CTHA) in Addition to Dynamic CT Studies to Identify Hypervascularity of Hepatocellular Carcinoma

PurposeTo identify factors benefiting from computed tomography during hepatic arteriography (CTHA) in addition to dynamic CT studies at the preoperative evaluation of the hypervascularity of hepatocellular carcinoma (HCC).Materials and MethodsWe retrospectively divided 45 patients with HCC, who underwent both dynamic CT (dCT) and CTHA, into two groups based on the number of hypervascular HCCs identified on dCT and CTHA studies. In group A, the number of HCCs identified by dCT and CTHA was the same and additive CTHA had not been indicated. In group B, fewer HCCs were counted on dCT than on CTHA images, indicating that additive CTHA studies had been appropriate. We compared the patient characteristics, the serum alpha-fetoprotein level, and the tumor-liver contrast (TLC) of the main tumor on dCT scans of both groups. To identify factors alerting to the benefit of additional CTHA studies, we performed univariate logistic regression analysis. Statistically significant parameters were subjected to receiver operating characteristic analysis for obtaining the optimal cutoff value indicative of the benefit of CTHA.ResultsUnivariate analysis identified only the TLC of the main tumor on dCT images as a significant factor for the benefit of CTHA images (P < 0.01). At the optimal cutoff value for the TLC of the main tumor on dCT images (15.9 Hounsfield units), the sensitivity and specificity for the benefit of CTHA were 85.0 and 92.0%, respectively.ConclusionEvaluation of the TLC of the main tumor on dCT scans identifies patients in whom additive CTHA studies are beneficial.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

The Effects of Low Frequency on the Microstructure and Mechanical Properties of High-Strength Al-Mg Aluminum Alloys by Wire and Double-Pulsed Arc Additive Manufacturing

An innovative and high deposition efficiency process, the double-pulsed arc additive manufacturing process, is used to produce high-strength Al-Mg wall components. This dissertation investigates the electrical parameter acquisition, bead appearance, porosity morphology, microstructure and mechanical properties of additively manufactured high-strength Al-Mg wall components and how these are affected by the low frequency of the double-pulsed arc additive manufacturing process. Then, using this process at different low frequencies of 0, 1, 3, 5, 7 and 9 Hz, multilayer deposition experiments were performed. It can be observed that the deposit porosity is obviously eliminated compared with cold metal transfer (CMT) process. The bead appearance of the deposited aluminum wall varies clearly with low frequencies, and at a low frequency of 3 Hz, its appearance is the best of all. The optical observation of microstructure proves that the average grain size varies significantly with low frequency, and at a low frequency of 1 Hz, it is the smallest. In addition, the deposited wall showed maximum mean microhardness and maximum ultimate tensile strength at a low frequency of 3 Hz. Considering the deposited porosity and mechanical priorities, double-pulsed arc additive manufacturing with a frequency of 3 Hz is more suitable for making high-strength Al-Mg wall components than at other low frequencies.

36 MATERIALS SCIENCE↗

Additively Manufactured Single-Use Molds and Reusable Patterns for Large Automotive and Hydroelectric Components

Additive manufacturing (AM) has the potential to reduce costs in the casting industry, particularly for large parts (i.e., components with any dimension > 12 in.). In this study, pilot-scale production case studies of hydroelectric and automotive parts were used to evaluate two AM-enabled casting methods: the direct printing of sand molds by binder jet and printing of reusable cope and drag patterns for sand casting. An additional benefit was found when additively manufactured patterns were used in combination with heat-treat free aluminum alloys, to produce castings of complex hydrodynamic surfaces. These parts previously required production via subtractive machining due to part distortion induced by the quench step of heat treatments. The machine types used for the three case studies are sand-binder jet, high-resolution polymer fused deposition modeling (FDM), and big area additive manufacturing (BAAM) FDM in combination with CNC machining. Each method demonstrated distinct advantages over traditional casting practices in particular use cases. Single-use molds show great reductions in start-up cost to produce one-off or legacy parts, and additively manufactured impression patterns show promise for innovating the tooling design process for complex geometry and large castings.

36 MATERIALS SCIENCE↗

Geometrical effects on the measured neutron residual stress in additively manufactured cold spray AA6061

Aluminum cold spray additive builds were made with varying wall widths and geometries to explore the effects of build geometry on residual stress development in the additively sprayed material. Deposition rates of over 750 g/hr were achieved without any cracking or delamination of the additively manufactured components. Neutron residual stress measurements revealed a maximum tensile residual stress of 41 MPa at the interface of the substrate and a maximum compressive residual stress of −35 MPa in the cold sprayed material. While there was not found to be significant residual stress changes between the cold sprayed walls, the cold sprayed cylinder had varying residual stress throughout the diameter with the outer diameter having a higher tensile residual stress than the interior. The low residual stress and minimal geometrical dependency demonstrate further part size is possible without concerns for component failure in AA6061. The application of common coating residual stress models to full scale additive builds is evaluated and discussed. The lack of residual stress evolution was studied by in-situ coating property measurement that revealed that the deposition stress of the AA6061 sprays reduced with increased layer thickness. In conclusion, this study provides insight into the evolution of residual stress in cold spray additive components and how both the mechanics and material responses differ from coatings.

Additive manufacturing↗

Unique W-Shape Y6 isomer as effective solid additive for High-Performance PM6:Y6 polymer solar cells

The current top-performing polymer solar cell (PSC) systems are mostly based on PM6:Y6 host blend. To date, numerous materials have been explored as the third component for these systems to form ternary blends or as additives. Vitrification agents are a group of additives proved to be useful in affecting the morphology of organic semiconductors. Here to design a suitable vitrification agent for non-fullerene electron acceptor Y6, an isomer strategy was explored where the thienothiophene wings of the Y6 molecule were inversed to form a W-shaped Y6 isomer of i-Y6. It was found that i-Y6 crystallized poorly with a different packing style than Y6 and could blend well in amorphous phase of Y6. These properties enabled i-Y6 to finely tune the morphology of PM6:Y6 blend at low additive dosages. The power conversion efficiency (PCE) of PM6:Y6 based PSC was raised from 16.827% to 17.433% at a dosage of Y6:i-Y6 ratio of 24:1. This work demonstrated isomerization as a viable strategy for developing solid additives for high performance PSC blends and vitrification agents as effective additives for tuning morphology and improving performances of PSCs.

36 MATERIALS SCIENCE↗

Phase stability and mechanical properties of wire + arc additively manufactured H13 tool steel at elevated temperatures

Wire + arc additive manufacturing (WAAM) is considered an innovative technology that can change the manufacturing landscape in the near future. WAAM offers the benefits of inexpensive initial system setup and a high deposition rate for fabricating medium- and large-sized parts such as die-casting tools. Here, AISI H13 tool steel, a popular die-casting tool metal, is manufactured by cold metal transfer (CMT)-based WAAM and is then comprehensively analyzed for its microstructural and mechanical properties. Location-dependent phase combinations are observed, which could be explained by nonequilibrium thermal cycles that resulted from the layer-by-layer stacking mechanism used in WAAM. In addition, remelting and reheating of the layers reduces welding anomalies (e.g., pores and voids). The metallurgical characteristics of the H13 strongly correlate with the mechanical properties. The combinations of phases at different locations of the additively manufactured part exhibit a periodic microhardness profile. Martensite, Retained Austenite, Ferrite, and Carbide phases are found in combination at different locations of the part based on the part’s temperature distribution during additive deposition. Moreover, the tensile properties at elevated temperatures (23 °C, 300 °C, and 600 °C) are comparable to those from other WAAM and additive manufacturing (AM) processes. The X-ray diffraction results verify that the microstructural stability of the fabricated parts at high temperatures would allow them to be used in high temperatures.

36 MATERIALS SCIENCE↗

Heavy ion irradiation response of an additively manufactured 316LN stainless steel

Additive manufacturing has become an appealing technique to fabricate three-dimensional metallic materials and components for nuclear reactors. However, response of additively manufactured alloys to high-dose heavy ion irradiations at elevated temperatures is still not well understood. Here, an additively manufactured 316LN austenitic stainless steel with high-density solidification cells was irradiated using 3.5 MeV Fe ion to a peak dose of 220 dpa at 450 °C. Microscopy studies show a lower Frank loop density and smaller size in the additively manufactured sample compared with its cold worked counterpart, and the cellular structures may largely suppress the formation of perfect loops and dislocation networks and reduce the magnitude of solute segregations comparing with high angle grain boundaries. In conclusion, the present work advances the understanding on the high-temperature irradiation response of additively manufactured steels for nuclear reactor applications.

36 MATERIALS SCIENCE↗

Postirradiation characterization of palladium as an additive for fuel cladding chemical interaction mitigation in metallic fuel

This work describes the microstructural and elemental characterization of irradiated metallic fuels containing palladium as an additive. The use of additives has been proposed to control Fuel-Cladding Chemical Interaction (FCCI) and thus to promote higher fuel utilization (i.e., higher burnup). In this work, Pd has been investigated as a potential additive to metallic fuel to bind lanthanides, impeding their migration and attack on the cladding. The influence of Pd on the microstructure, chemistry and performance of metallic fuel has been characterized via scanning electron microscopy for two metallic fuel designs—namely, annular and solid fuel. Pd was observed to play an important role in the chemistry of the fuel. Indeed, the addition of Pd leads to the formation of new phases. Pd was detected to combine not only with the lanthanides, as intended, but also with Zr, a main element of the fuel matrix. While Pd proved to be effective in preventing lanthanide migration and their attack on the cladding, the Pd-Zr compound may potentially lead to other unexpected fuel-performance issues, such as the formation of low-melting point phases and increased unalloyed U available for FCCI interaction with Fe in the cladding. Even the increase of Zr to 13wt%. did not completely mitigate this adverse phenomenon generated by the Pd-Zr interaction. Furthermore, the efficacy of using this additive needs further investigation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

EBSD analysis of magnesium addition on inclusion formation in SS400 structural steel

In this study, the effect of magnesium addition on the inclusion formation in SS400 steel was investigated. The experimental specimens with and without Mg addition treatment were compared. The microstructure was observed using optical microscopy after etching with 3% nital. The morphology and chemical composition of the inclusions were analyzed via scanning electron microscopy and energy dispersive spectrometry. The lattice structure and orientation of the inclusions were identified by electron backscattering diffraction. The average size of inclusions in SS400 was between 0.67 and 0.75 μm, and between 0.65 and 0.68 μm in SS400 + Mg. The 2 ppm Mg addition resulted in the oxide formation change from Al{sub 2}O{sub 3} to MgO·Al{sub 2}O{sub 3} and in the inclusion formation change from Al{sub 2}O{sub 3}–MnS to MgO·Al{sub 2}O{sub 3}–MnS. Moreover, a simple-phase MnS with an average grain size of 1 μm to 2 μm was observed in rod-like, globular, and polyhedron forms. - Highlights: • The effect of magnesium addition was investigated for SS400 steel. • 2 ppm Mg addition changes the inclusion formation from Al2O3-MnS to MgO·Al2O3-MnS. • MnS observed in inclusions exhibits rod-like, globular, and polyhedron forms.

36 MATERIALS SCIENCE↗

Effects of boron addition on the morphology of silicon phases in Al-Si casting alloys

Highlights: • The influence of boron on Si phase was studied. • Boron addition reduces the length of eutectic Si plates in Al-11Si alloys. • Boron addition promotes the nucleation temperature of primary Si phases in Al-14Si alloys. • Boron addition increases the twin density in the <112>{sub Si} growth direction of eutectic Si in Al-11Si and Al-14Si alloys. - Abstract: The influence of B elements on the morphology of Si phases in Al-11Si and Al-14Si alloys has been investigated employing Optical Microscope, Scanning Electron Microscopy, Transmission Electron Microscopy and Differential Scanning Calorimetry. In Al-11Si alloy, the addition of B element not only refines the primary Al dendrites, but also reduces the length of eutectic Si plates. In Al-14Si alloys, the addition of B element promotes the nucleation temperature of primary Si phases, but shows weak influence on the nucleation temperature of eutectics. The effects of B element on the morphologies of both primary Si particle and eutectics can be attributed to the interaction between B and Si elements during the solidification process.

36 MATERIALS SCIENCE↗

Optimizing the impacts of solid additives on the operational stability and processing reliability of organic solar cells

Previous reports have revealed that by leveraging solid additives, organic solar cells (OSCs) can surpass the device’s performance beyond the intrinsic limitations of host photoactive molecules, a remarkable advancement. However, the impacts of more complex interactions introduced by solid additives are not yet well understood. Herein, optimizing the fabrication process based on the traditional efficiency-guided approach fails to represent the ideal and most practical devices. In particular, achieving superior operational stability while minimizing the device performance scattering was found to require processing solvent evaporation to be synchronized with the volatility of the chosen solid additive. However, this may be challenging since most organic photoactive materials display excellent efficiencies only with selected solvents. Accordingly, this work also demonstrates the potential of dual and complementary solvents selection, consisting of low boiling point (primary) and high boiling point (secondary). This strategy allows for the suppression of any potential trade-offs in efficiency. Meanwhile, the operational stability and precision of device performance are substantially enhanced. Additionally, solid additives have demonstrated that the singlet exciton dissociation rate does not limit the free charge generation yield. Finally, these findings are expected to reformulate OSC device fabrication strategies towards more practical devices.

36 MATERIALS SCIENCE↗

Creep suppression and fatigue in bio-based composites manufactured via conventional and large format additive manufacturing processes

The emergence of novel extrusion-based additive manufacturing (AM) processes has prompted the development of new thermoplastic composite feedstocks, and broadening sustainability initiatives have driven the development of bio-based and recyclable material for AM feedstocks. Poly(lactic acid) (PLA) with wood flour (WF) is one composite system that has been demonstrated in numerous AM applications, as well as traditional processing methods (i.e., compression and injection molding); however, there has been a need to understand how the variation in processing methodology impacts the material performance of these bio-based feedstocks from a fundamental perspective, with particular emphasis on creep for an extended application use-life. Herein, PLA/WF is explored as a feedstock material for large format additive manufacturing (LFAM) and the performance of additively manufactured materials is compared to those produced via more traditional processing methods. It is also demonstrated that the addition of WF decreases the material’s coefficient of thermal expansion (CTE) while increasing its Young’s modulus, susceptibility to water uptake, and creep fatigue resistance. Essentially, the addition of 20 wt% WF results in a 92 % decrease in rubbery regime CTE while simultaneously resulting in a 14 % increase in modulus, 190 % increase in water uptake, and a 31 % decrease in residual strain after cyclic creep tests. The processing method was also found to play a large role in the final part performance, with the printed material increasing the crystallinity by 183 % and 214 % compared to its compression and injection molded counterparts. Furthermore, the porosity of printed samples increased by two orders of magnitude compared to samples prepared via traditional processing methods.

36 MATERIALS SCIENCE↗

Structure of a stratified CH 4 flame with H 2 addition

To explore the effect of H 2 addition (20 percent by volume) on stratified-premixed methane combustion in a turbulent flow, an experimental investigation on a new flame configuration of the Darmstadt stratified burner is conducted here. Major species concentrations and temperature are measured with high spatial resolution by 1D Raman-Rayleigh scattering. A conditioning on local equivalence ratio (range from φ = 0.45 to φ = 1.25) and local stratification is applied to the large dataset and allows to analyze the impact of H 2 addition on the flame structure. The local stratification level is determined as Δφ/ΔT at the location of maximum CO mass fraction for each instantaneous flame realization. Due to the H 2 addition, preferential diffusion of H 2 is different than in pure methane flames. In addition to diffusing out of the reaction zone where it is formed, particularly in rich conditions, H 2 also diffuses from the cold reactant mixture into the flame front. For rich conditions (φ = 1.05 to φ = 1.15) H 2 mass fractions are significantly elevated within the intermediate temperature range compared to fully-premixed laminar flame simulations. This elevation is attributed to preferential transport of H 2 into the rich flame front from adjacent even richer regions of the flow. Additionally, when the local stratification across the flame front is taken into account, it is revealed that the state-space relation of H 2 is not only a function of the local stoichiometry but also the local stratification level. In these flames H 2 is the only major species showing sensitivity of the state-space relation to an equivalence ratio gradient across the flame front.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Additive and synergistic antiandrogenic activities of mixtures of azol fungicides and vinclozolin

Objective: Many pesticides including pyrethroids and azole fungicides are suspected to have an endocrine disrupting property. At present, the joint activity of compound mixtures is only marginally known. Here we tested the hypothesis that the antiandrogenic activity of mixtures of azole fungicides can be predicted by the concentration addition (CA) model. Methods: The antiandrogenic activity was assessed in MDA-kb2 cells. Following assessing single compounds activities mixtures of azole fungicides and vinclozolin were investigated. Interactions were analyzed by direct comparison between experimental and estimated dose–response curves assuming CA, followed by an analysis by the isobole method and the toxic unit approach. Results: The antiandrogenic activity of pyrethroids deltamethrin, cypermethrin, fenvalerate and permethrin was weak, while the azole fungicides tebuconazole, propiconazole, epoxiconazole, econazole and vinclozolin exhibited strong antiandrogenic activity. Ten binary and one ternary mixture combinations of five antiandrogenic fungicides were assessed at equi-effective concentrations of EC{sub 25} and EC{sub 50}. Isoboles indicated that about 50% of the binary mixtures were additive and 50% synergistic. Synergism was even more frequently indicated by the toxic unit approach. Conclusion: Our data lead to the conclusion that interactions in mixtures follow the CA model. However, a surprisingly high percentage of synergistic interactions occurred. Therefore, the mixture activity of antiandrogenic azole fungicides is at least additive. Practice: Mixtures should also be considered for additive antiandrogenic activity in hazard and risk assessment. Implications: Our evaluation provides an appropriate “proof of concept”, but whether it equally translates to in vivo effects should further be investigated. - Highlights: • Humans are exposed to pesticide mixtures such as pyrethroids and azole fungicides. • We assessed the antiandrogenicity of pyrethroids and azole fungizides. • Many azole fungicides showed significant antiandrogenic activity . • Many binary mixtures of antiandrogenic azole fungicides showed synergistic interactions. • Concentration addition of pesticides in mixtures should be considered.

60 APPLIED LIFE SCIENCES↗

Transformation of Cerium Oxide Nanoparticles from a Diesel Fuel Additive during Combustion in a Diesel Engine

Nanoscale cerium oxide is used as a diesel fuel additive to reduce particulate matter emissions and increase fuel economy, but its fate in the environment has not been established. Here, cerium oxide released as a result of the combustion of diesel fuel containing the additive Envirox TM , which utilizes suspended nanoscale cerium oxide to reduce particulate matter emissions and increase fuel economy, was captured from the exhaust stream of a diesel engine and was characterized using a combination of bulk analytical techniques and high resolution transmission electron microscopy. The combustion process induced significant changes in the size and morphology of the particles; ~15 nm aggregates consisting of 5 to 7 nm faceted crystals in the fuel additive became 50 to 300 nm, near-spherical, single crystals in the exhaust. Electron diffraction identified the original cerium oxide particles as cerium (IV) oxide (CeO 2 , standard FCC structure) with no detectable quantities of Ce(III), whereas in the exhaust the ceria particles had additional electron diffraction reflections indicative of a CeO 2 superstructure containing ordered oxygen vacancies. The surfactant coating present on the cerium oxide particles in the additive was lost during combustion, but in roughly 30% of the observed particles in the exhaust, a new surface coating formed, approximately 2 to 5 nm thick. The results of this study suggest 28 that pristine, laboratory-produced, nanoscale cerium oxide is not a good substitute for the cerium 29 oxide released from fuel borne catalyst applications and that future toxicity experiments and modeling will require the use/consideration of more realistic materials.

54 ENVIRONMENTAL SCIENCES↗

Mechanisms of Metal Additive-Induced Ordering During SNIPS Membrane Formation

Isoporous membranes can be fabricated by combining self-assembly with nonsolvent induced phase separation (SNIPS) using an amphiphilic block copolymer like polystyrene-b-poly(4-vinylpyridine) (SV). Poly(4-vinylpyridine) (V) is known to complex with metal salts, which are hypothesized to stabilize solution ordering and preserve structure during casting. We explored how the molar ratio of metal additive to the poly(4-vinylpyridine) block affected the final membrane morphology via scanning electron microscopy (SEM). Dynamic light scattering (DLS), small-angle X-ray scattering (SAXS), and in situ grazing-incidence SAXS were used to track changes in solution ordering and chain conformation as a function of the molar ratio of the additive to the V block. Additives induced aggregation, promoted the formation of more compact conformations in solution, and facilitated micelle ordering onto lattices at optimal ratios. Furthermore, these experimental results were supported by random phase approximation calculations, which helped explain how the thermodynamic order–disorder transition shifts with additive binding strength. Stronger additive–polymer interactions reduced the block copolymer volume fraction required for ordering in solution, allowing ordered domains to form at lower polymer concentrations.

Additives↗