SEARCH · Engineering Papers

Results for “AIRPLANES - STRENGTH CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

NASA NTRS1954

A Procedure for the Design of Air-Heated Ice-Prevention Systems

A procedure proposed for use in the design of air-heated systems for the continuous prevention of ice formation on airplane components is set forth. Required heat-transfer and air-pressure-loss equations are presented, and methods of selecting appropriate meteorological conditions for flight over specified geographical areas and for the calculation of water-drop-impingement characteristics are suggested. In order to facilitate the design, a simple electrical analogue was devised which solves the complex heat-transfer relationships existing in the thermal-system analysis. The analogue is described and an illustration of its application to design is given.

Neel, C. B.↗

NASA NTRS1930

The Effect of Wing Tip Floating Ailerons on the Autorotation of a Monoplane Wing Model

The preliminary tests described here were made to determine the extent to which wing tip floating ailerons might be effective in reducing airplane spinning tendencies. The tests showed that initial spinning tendencies and rates of stable spinning could doubtless be reduced by the use of tip floating ailerons on an airplane. It also appears to be desirable to reduce to a minimum the interference between wing and aileron. This would serve to maintain uniformity of action at all angles of attack and enable calculation of the aileron characteristics.

Knight, Montgomery↗

NASA NTRS1988

Calculating Rotor/Stator Interactions

Analysis procedure and associated computer code use Euler equations of fluid motion and patched coordinate grids to simulate fluid flow about rotor airfoil moving with respect to stator airfoil. Procedure useful in studies of interactions between rotors and stators in turbines, propellers and nacelles on airplanes, and rotors and fuselages on helicopters.

Rai, Man Mohan↗

NASA NTRS1990

Calculating Irradiance For Photosynthesis In The Ocean

Mathematical model predicts available and usable irradiances. Yields estimates of irradiance available for photosynthesis (Epar) and irradiance usable for photosynthesis (Epur) as functions of depth in ocean. Describes Epur and Epar in terms of spectral parameters measured remotely (from satellites or airplanes). These irradiances useful in studies of photosynthetic productivity of phytoplankton in euphotic layer.

Collins, Donald J.↗

NASA NTRS1959

Ground Measurements of the Shock-Wave Noise from Airplanes in Level Flight at Mach Numbers to 1.4 and at Altitudes to 45000 Feet

Time histories of noise pressures near ground level were measured during flight tests of fighter-type airplanes over fairly flat, partly wooded terrain in the e Mach number range between 1.13 and 1.4 and at altitudes from 25,000 to 45,000 feet. Atmospheric soundings and radar tracking studies were made for correlation with the measured noise data. The measured and calculated values of the pressure rise across the shock wave were generally in good agreement. There is a tendency for the theory to overestimate the pressure at locations remote from the track and to underestimate the pressures for conditions of high tailwind at altitude. The measured values of ground-reflection factor averaged about 1.8 f or the surface tested as compared to a theoretical value of 2.0. P o booms were measured in all cases. The observers also generally reported two booms; although, in some cases, only one boom was reported. The shock-wave noise associated with some of the flight tests was judged to be objectionable by ground observers, and in one case the cracking of a plate-glass store window was correlated in time with the passage of the airplane at an altitude of 25,000 feet.

Maglieri, Domenic J.↗

NASA NTRS1994

Simplified Aerodynamic and Structural Modeling for Oblique All-Wing Aircraft. Phase 2: Structures

Any aircraft preliminary design study requires a structural model of the proposed configuration. The model must be capable of estimating the structural weight of a given configuration, and of predicting the deflections which will result from foreseen flight and ground loads. The present work develops such a model for the proposed Oblique All Wing airplane. The model is based on preliminary structural work done by Jack Williams and Peter Rudolph at Mdng, and is encoded in a FORTRAN program. As a stand-alone application, the program can calculate the weight CG location, and several types of structural deflections; used in conjunction with an aerodynamics model, the program can be used for mission analysis or sizing studies.

Kroo, Ilan↗

NASA NTRS1960

Studies of the Retardation Force Developed on an Aircraft Tire Rolling in Slush or Water

A series of unbraked (freely rolling) taxi tests were conducted at the Langley landing-loads track with a 32 x 8.8, type 7, 22-ply-rating ribbed-tread aircraft tire to obtain data on tire retardation forces developed during rolling in both slush and water. The forward speeds of the tests ranged from 59 to 104 knots. Tire inflation pressures of 350 and 115 pounds per square inch were used. Results indicated a parabolic increase of retardation force with increasing forward velocity for both slush- and water-covered runway surfaces. The retardation force was found to increase approximately linearly with increasing water depth. Drag coefficients appropriate to the equations used are presented. Calculations made to determine the effect of slush on the take-off distance of a jet transport are in agreement with data obtained from an actual take-off in slush for this airplane. This is an interim report which deals with the effect of slush on the acceleration and the ground-run distance of airplanes during take-off.

Horne, Walter B.↗

NASA NTRS1937

Accelerations in Landing with a Tricycle-Type Landing Gear

In connection with the application of stable tricycle-type landing gears to transport airplanes, the question arises as to whether certain passengers may not experience relatively great accelerations in an emergency landing. Since the main landing wheels are behind the center of gravity in this type of gear, a hard-braked landing will cause immediate nosing down of the airplane and, when this motion is stopped due to the front wheel striking the ground, there will be some tendency for the rearmost passengers to be thrown out of their seats, The provided rough calculations are designed to show the magnitudes of the various reactions experienced in a severe landing under these circumstances.

Jones, Robert T.↗

NASA NTRS1921

Airplane Superchargers

Discussed here are the principles and operation of aircraft engine superchargers used to maintain and increase engine power as aircraft encounter decreases in the density of air as altitude rises. Details are given on the design and operation of the centrifugal compressors. A method is given for calculating the amount of power needed to drive a compressor. The effects of the use of a compressor on fuel system operation and design are discussed. Several specific superchargers that were in operation are described.

Noack, W G↗

NASA NTRS1977

Use of experimental separation limits in the theoretical design of V/STOL inlets

Experimental data from several model inlets are used to generate two parameters which are related to the limit of operation for inlet flow separation. One parameter, called the diffusion ratio, is the ratio of the peak velocity on the inlet surface to the velocity at the diffuser exit and is related to the boundary-layer separation at low throat Mach numbers. The other parameter, the peak Mach number on the inlet surface, is related to the separation at high throat Mach numbers. These parameters are easily calculated from potential flow solutions and thus can be used as a design tool in screening proposed inlet geometries. An illustrative example of an application to an inlet design study for a tilt nacelle VTOL airplane is presented. The value of contraction ratio required to meet the operating requirements yet allow the inlet to remain free of separation as indicated by the two separation parameters is shown.

Boles, M. A.↗

NASA NTRS1992

Thrust stand evaluation of engine performance improvement algorithms in an F-15 airplane

An investigation is underway to determine the benefits of a new propulsion system optimization algorithm in an F-15 airplane. The performance seeking control (PSC) algorithm optimizes the quasi-steady-state performance of an F100 derivative turbofan engine for several modes of operation. The PSC algorithm uses an onboard software engine model that calculates thrust, stall margin, and other unmeasured variables for use in the optimization. As part of the PSC test program, the F-15 aircraft was operated on a horizontal thrust stand. Thrust was measured with highly accurate load cells. The measured thrust was compared to onboard model estimates and to results from posttest performance programs. Thrust changes using the various PSC modes were recorded. Those results were compared to benefits using the less complex highly integrated digital electronic control (HIDEC) algorithm. The PSC maximum thrust mode increased intermediate power thrust by 10 percent. The PSC engine model did very well at estimating measured thrust and closely followed the transients during optimization. Quantitative results from the evaluation of the algorithms and performance calculation models are included with emphasis on measured thrust results. The report presents a description of the PSC system and a discussion of factors affecting the accuracy of the thrust stand load measurements.

Conners, Timothy R.↗

NASA NTRS1944

NACA investigation of a jet-propulsion system applicable to flight

Following a brief history of the NACA investigation of jet propulsion, a discussion is given of the general investigation and analysis leading to the construction of the jet-propulsion ground-test mock-up. The results of burning experiments and of test measurements designed to allow quantitative flight performance predictions of the system are presented and correlated with calculations. These calculations are then used to determine the performance of the system on the ground and in the air at various speeds and altitudes under various burning conditions. The application of the system to an experimental airplane is described and some performance predictions for this airplane are made.

Ellis, Macon C , Jr↗

NASA NTRS1943

NACA Investigation of a Jet-Propulsion System Applicable to Flight

Ellis, Macon C.↗

NASA NTRS1947

A Method for Calculating the Heat Required for Windshield Thermal Ice Prevention Based on Extensive Flight Tests in Natural Icing Conditions

An equation is presented for calculating the heat flow required from the surface of an internally heated windshield in order to prevent the formation of ice accretions during flight in specified icing conditions. To ascertain the validity of the equation, comparison is made between calculated values of the heat required and measured values obtained for test windshields in actual flights in icing conditions. The test windshields were internally heated and provided data applicable to two common types of windshield configurations; namely the V-type and the type installed flush with the fuselage contours. These windshields were installed on a twin-engine cargo airplane and the icing flights were conducted over a large area of the United States during the winters of 1945-46 and 1946-47. In addition to the internally heated windshield investigation, some test data were obtained for a windshield ice-prevention system in which heated air was discharged into the windshield boundary layer. The general conclusions resulting from this investigation are as follows: 1) The amount of heat required for the prevention of ice accretions on both flush- and V-type windshields during flight in specified icing conditions can be calculated with a degree of accuracy suitable for design purposes. 2) A heat flow of 2000 to 2500 Btu per hour per square foot is required for complete and continuous protection of a V-type windshield in fight at speeds up to 300 miles per hour in a moderate cumulus icing condition. For the same degree of protection and the same speed range, a value of 1000 Btu per hour per square foot suffices in a moderate stratus icing condition. 3) A heat supply of 1000 Btu per hour per square foot is adequate for a flush windshield located well aft of the fuselage stagnation region, at speeds up to 300 miles per hour, for flight in both stratus and moderate cumulus icing conditions. 4) The external air discharge system of windshield thermal ice prevention is thermally inefficient and requires a heat supply approximately 20 times that required for an internal system having the same performance.

ICE FORMATION↗

NASA NTRS1980

Optical measurements of degradation in aircraft boundary layers

Visible wavelength measurements of the degradation of optical beams when transmitted through the thin aerodynamic boundary layers around an aircraft are reviewed. The measured results indicated degradation levels for the KC-135 airplanes between 0.10 to 0.13 lambda increasing to 0.18 lambda (rms wavefront distortion). For the Lear Jet, degradation with a 25 mm diameter optics was roughly 0.07 lambda. The corresponding infinite aperture degradation levels are also calculated. The corresponding measured correlation lengths of roughly 12 mm for the KC-135 aircraft and 6 mm for the Lear Jet scale to roughly 20 and 25 mm, respectively, for infinite apertures. These boundary layer correlation lengths do not appear to reflect the different boundary layer thicknesses on the two different aircraft.

Kelsall, D.↗

NASA NTRS1930

Contribution to the theory of propeller vibrations

This report presents a calculation of the torsional frequencies of revolving bars with allowance for the air forces. Calculation of the flexural or bonding frequencies of revolving straight or tapered bars in terms of the angular velocity of revolution. Calculation on the basis of Rayleigh's principle of variation. There is also a discussion of error estimation and the accuracy of results. The author then provides an application of the theory to screw propellers for airplanes and the discusses the liability of propellers to damage through vibrations due to lack of uniform loading.

Liebers, F↗

NASA NTRS1986

Wake shape and its effects on aerodynamic characteristics

The wake shape under symmetrical flight conditions and its effects on aerodynamic characteristics are examined. In addition, the effect of wake shape in sideslip and discrete vortices such as strake or forebody vortex on lateral characteristics is presented. The present numerical method for airplane configurations, which is based on discretization of the vortex sheet into vortex segments, verified the symmetrical and asymmetrical roll-up process of the trailing vortices. Also, the effect of wing wake on tail planes is calculated. It is concluded that at high lift the assumption of flat wake for longitudinal and lateral-directional characteristics should be reexamined.

Emdad, H.↗

NASA NTRS1925

Recent progress in the theoretical deduction of airplane wings

The designing of an airplane requires an accurate knowledge of the aerodynamic properties of its wings, as expressed in the polar diagram. It is important to continue the theoretical researches on the aerodynamic phenomena of wings, in order to determine by calculation, their fundamental characteristics and to increase and formulate our knowledge in this field.

WINGS - CHARACTERISTICS↗