Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AG”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Influence of annealing and Ag doping on structural and optical properties of indium tin oxide thin films

Indium tin oxide (ITO) and Ag (1.2{+-}0.1 at. %)-ITO films with the thickness of 130 nm were deposited on glass substrates at room temperature by dc magnetron sputtering and postannealed at the temperature range of 200-400 deg. C. By calculating the x-ray diffraction data, the lattice constants of all samples were obtained and the results show that the annealing led to the smaller lattice constants and the Ag doping resulted in the further lattice distortion. The refractive index n and extinction coefficient k of all samples were extracted from the transmittance spectra by means of the spectroscopic ellipsometry optimization method. Ag-ITO film annealed at 400 deg. C has the high transmittance of 80%-90% in the visible wavelength range. Ag doping dramatically increased the extinction coefficient k of ITO films in UV wavelength range but almost without change in it in visible band. Meanwhile, by contrast with ITO films, Ag-ITO films show much higher n values than that of ITO films. Finally, the optical band gaps of all samples were determined, and it has been found that there is almost no difference of band gaps between ITO and Ag-ITO films. The reasons of the influence of annealing and Ag doping on structural and optical properties of ITO thin films are discussed.

36 MATERIALS SCIENCE↗

Ag films grown by remote plasma enhanced atomic layer deposition on different substrates

Silver (Ag) layers were deposited by remote plasma enhanced atomic layer deposition (PALD) using Ag(fod)(PEt{sub 3}) (fod = 2,2-dimethyl-6,6,7,7,8,8,8-heptafluorooctane-3,5-dionato) as precursor and hydrogen plasma on silicon substrate covered with thin films of SiO{sub 2}, TiN, Ti/TiN, Co, Ni, and W at different deposition temperatures from 70 to 200 °C. The deposited silver films were analyzed by x-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) with energy dispersive x-ray spectroscopy, four point probe measurement, ellipsometric measurement, x-ray fluorescence (XRF), and x-ray diffraction (XRD). XPS revealed pure Ag with carbon and oxygen contamination close to the detection limit after 30 s argon sputtering for depositions made at 120 and 200 °C substrate temperatures. However, an oxygen contamination was detected in the Ag film deposited at 70 °C after 12 s argon sputtering. A resistivity of 5.7 × 10{sup −6} Ω cm was obtained for approximately 97 nm Ag film on SiO{sub 2}/Si substrate. The thickness was determined from the SEM cross section on the SiO{sub 2}/Si substrate and also compared with XRF measurements. Polycrystalline cubic Ag reflections were identified from XRD for PALD Ag films deposited at 120 and 200 °C. Compared to W surface, where poor adhesion of the films was found, Co, Ni, TiN, Ti/TiN and SiO{sub 2} surfaces had better adhesion for silver films as revealed by SEM, TEM, and AFM images.

36 MATERIALS SCIENCE↗

Green Synthesis of Ag and Pd Nanospheres, Nanowires, and Nanorods Using Vitamin B 2 : Catalytic Polymerisation of Aniline and Pyrrole

For the first time, we report green chemistry approach using vitamin B 2 in the synthesis of silver (Ag) and palladium (Pd), nanospheres, nanowires, and nanorods at room temperature without using any harmful reducing agents, such as sodium borohydride ( NaBH 4 ) or hydroxylamine hydrochloride and any special capping or dispersing agent. Vitamin B 2 was used as reducing agent as well as capping agent due to its high-water solubility, biodegradability, and low-toxicity compared with other reducing agents. The average particle size of nanoprticle was found to be Ag (average size 6.1 ± 0.1 nm) and Pd (average size 4.1 ± 0.1 nm) nanoparticles in ethylene glycol and Ag (average size 5.9 ± 0.1 nm, and average size 6.1 ± 0.1) nanoparticles in acetic acid and NMP, respectively. The formation of noble multiple shape nanostructures and their self assembly were dependent on the solvent employed for the preparation. When water was used as solvent media, Ag and Pd nanoparticles started to self-assemble into rod-like structures and in isopropanol Ag and Pd nanoparticles yielded wire-like structures with a thickness in the range of 10 to 20 nm and several hundred microns in length. In acetone and acetonitrile medium, the Ag and Pd nanoparticles are self-assembled into a regular pattern making nanorod structures with thicknesses ranging from 100 to 200 nm and lengths of a few microns. The so-synthesized nanostructures were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray (EDX) analysis, and UV spectroscopy. The ensuing Ag and Pd nanoparticles catalyzed the reactions of aniline and pyrrole to generate polyaniline and polypyrrole nanofibers and may find various technological and biological applications. This single-step greener approach is general and can be extended to other noble metals and transition metal oxides.

Nadagouda, Mallikarjuna N.↗

Simulations of Merging and Squeezing Bunches in Booster and AGS

During the 2012 RHIC run, uranium, gold, and copper ions from EBIS were accelerated in Booster and AGS and delivered to RHIC for the physics program. In order to achieve the desired number of ions per bunch in RHIC, it was necessary to merge bunches in both Booster and AGS. After the bunches are merged in AGS, they need to be squeezed into harmonic 12 buckets for subsequent acceleration. In this note we carry out simulations of bunch merging and squeezing in Booster and AGS. These are meant to serve as benchmarks for what can be achieved in practice. In Booster the total longitudinal emittance of the 4 bunches to be merged is taken to be 0.15 eV s per nucleon. In AGS the total for each group of 4 bunches to be merged is taken to be 0.60 eV s per nucleon. The simulations show that the RF voltages currently available in Booster and AGS are sufficient for merging and holding the merged bunches in RF buckets. The voltages available in AGS are not sufficient for completely squeezing the merged bunches into harmonic 12 buckets. The merging of bunches is treated in sections 9 through 12. The required squeezing into harmonic 12 buckets is treated in sections 13 and 14. Debunching and rebunching beam as an alternative to merging bunches in Booster is treated in section 15. For completeness, sections 1 through 8 give a derivation of the turn-by-turn equations of longitudinal motion at constant magnetic field. The derivation is based on the work of MacLachlan. The reader may wish to skip over these sections and start with section 9.

43 PARTICLE ACCELERATORS↗

Simulations of Merging and Squeezing Bunches in Booster and AGS

During the 2012 RHIC run, uranium, gold, and copper ions from EBIS were accelerated in Booster and AGS and delivered to RHIC for the physics program. In order to achieve the desired number of ions per bunch in RHIC, it was necessary to merge bunches in both Booster and AGS. After the bunches are merged in AGS, they need to be squeezed into harmonic 12 buckets for subsequent acceleration. In this note we carry out simulations of bunch merging and squeezing in Booster and AGS. These are meant to serve as benchmarks for what can be achieved in practice. In Booster the total longitudinal emittance of the 4 bunches to be merged is taken to be 0.15 eV s per nucleon. In AGS the total for each group of 4 bunches to be merged is taken to be 0.60 eV s per nucleon. The simulations show that the RF voltages currently available in Booster and AGS are sufficient for merging and holding the merged bunches in RF buckets. The voltages available in AGS are not sufficient for completely squeezing the merged bunches into harmonic 12 buckets. The merging of bunches is treated in sections 9 through 12. The required squeezing into harmonic 12 buckets is treated in sections 13 and 14. Debunching and rebunching beam as an alternative to merging bunches in Booster is treated in section 15. For completeness, sections 1 through 8 give a derivation of the turn-by-turn equations of longitudinal motion at constant magnetic field. The derivation is based on the work of MacLachlan. The reader may wish to skip over these sections and start with section 9.

43 PARTICLE ACCELERATORS↗

The AGS with four helical magnets

The idea of using multiple partial helical magnets was applied successfully to the AGS synchrotron, to preserve the proton beam polarization. In this paper we explore in details the idea of using four helical magnets placed symmetrically in the AGS ring. This modification provides many advantages over the present setup of the AGS that uses two partial helical magnets. First, it provides a larger 'spin tune gap' for the placement of the vertical betatron tune of the AGS during acceleration, second, the vertical spin direction during the beam injection and extraction is closer to vertical, third, the symmetric placement of the snakes allows for a better control of the AGS optics, and for reduced values of the beta and eta functions, especially near injection, fourth, the optical properties of the helical magnets also favor the placement of the horizontal betatron tune in the 'spin tune gap', thus eliminating the horizontal spin resonances. In this paper we provide results on the spin tune and on the optics of the AGS with four partial helical magnets, and we compare these results with the present setup of the AGS that uses two partial helical magnets.

43 PARTICLE ACCELERATORS↗

Crystalline Structure-Dependent Mechanical and Thermoelectric Performance in Ag 2 Se 1–x S x System

Self-powered wearable electronics require thermoelectric materials simultaneously with a high dimensionless figure of merit (zT) and good flexibility to convert the heat discharged by the human body into electricity. Ag 2 (S,Se)-based semiconducting materials can well satisfy these requirements, and thus, they are attracting great attention in thermoelectric society recently. Ag 2 (S,Se) crystalizes in an orthorhombic structure or monoclinic structure, depending on the detailed S/Se atomic ratio, but the relationship between its crystalline structure and mechanical/thermoelectric performance is still unclear to date. In this study, a series of Ag 2 Se 1–x S x (x = 0, 0.1, 0.2, 0.3, 0.4, and 0.45) samples were prepared and their mechanical and thermoelectric performance dependence on the crystalline structure was systematically investigated. x = 0.3 in the Ag 2 Se 1–x S x system was found to be the transition boundary between orthorhombic and monoclinic structures. Mechanical property measurement shows that the orthorhombic Ag 2 Se 1–x S x samples are brittle while the monoclinic Ag 2 Se 1–x S x samples are ductile and flexible. In addition, the orthorhombic Ag 2 Se 1–x S x samples show better electrical transport performance and higher zT than the monoclinic samples under a comparable carrier concentration, most likely due to their weaker electron-phonon interactions. This study sheds light on the further development of flexible inorganic TE materials.

36 MATERIALS SCIENCE↗

KGML-ag: a modeling framework of knowledge-guided machine learning to simulate agroecosystems: a case study of estimating N<sub>2</sub>O emission using data from mesocosm experiments

Abstract. Agricultural nitrous oxide (N2O) emission accounts for a non-trivial fraction of global greenhouse gas (GHG) budget. To date, estimating N2O fluxes from cropland remains a challenging task because the related microbial processes (e.g., nitrification and denitrification) are controlled by complex interactions among climate, soil, plant and human activities. Existing approaches such as process-based (PB) models have well-known limitations due to insufficient representations of the processes or uncertainties of model parameters, and due to leverage recent advances in machine learning (ML) a new method is needed to unlock the “black box” to overcome its limitations such as low interpretability, out-of-sample failure and massive data demand. In this study, we developed a first-of-its-kind knowledge-guided machine learning model for agroecosystems (KGML-ag) by incorporating biogeophysical and chemical domain knowledge from an advanced PB model, ecosys, and tested it by comparing simulating daily N2O fluxes with real observed data from mesocosm experiments. The gated recurrent unit (GRU) was used as the basis to build the model structure. To optimize the model performance, we have investigated a range of ideas, including (1) using initial values of intermediate variables (IMVs) instead of time series as model input to reduce data demand; (2) building hierarchical structures to explicitly estimate IMVs for further N2O prediction; (3) using multi-task learning to balance the simultaneous training on multiple variables; and (4) pre-training with millions of synthetic data generated from ecosys and fine-tuning with mesocosm observations. Six other pure ML models were developed using the same mesocosm data to serve as the benchmark for the KGML-ag model. Results show that KGML-ag did an excellent job in reproducing the mesocosm N2O fluxes (overall r2=0.81, and RMSE=3.6 mgNm-2d-1 from cross validation). Importantly, KGML-ag always outperforms the PB model and ML models in predicting N2O fluxes, especially for complex temporal dynamics and emission peaks. Besides, KGML-ag goes beyond the pure ML models by providing more interpretable predictions as well as pinpointing desired new knowledge and data to further empower the current KGML-ag. We believe the KGML-ag development in this study will stimulate a new body of research on interpretable ML for biogeochemistry and other related geoscience processes.

54 ENVIRONMENTAL SCIENCES↗

Near integer tune for polarization preservation in the AGS

The high energy (T = 250 GeV) polarized proton beam experiments performed in RHIC, require high polarization of the beam. In order to preserve the polarization of the proton beam, during the acceleration in the AGS, which is the pre-injector to RHIC, we have installed in AGS two partial helical magnets which minimize the loss of the beam polarization caused by the various intrinsic spin resonances occurring during the proton acceleration. The minimization of the polarization loss during the acceleration cycle, requires that the vertical tune of the AGS is between the values of 8.97 and 8.985 during the acceleration. With the AGS constrained to run at near integer tune {approx}8.980, the perturbations to the beam caused by the partial helical magnets are large and also result in large beta and dispersion waves. To mitigate the adverse effect of the partial helices on the optics of the AGS, we have installed in specified straight sections of the AGS compensation quads and we have also generated a beam bump at the location of the cold partial helix. In this paper we present the beam optics of the AGS which ameliorates the adverse effect of the two partial helices on the beam optics.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Progress in Solving the Elusive Ag Transport Mechanism in TRISO Coated Particles: What is new?

The TRISO particle for HTRs has been developed to an advanced state where the coating withstands internal gas pressures and retains fission products during irradiation and under postulated accidents. However, one exception is Ag that has been found to be released from high quality TRISO coated particles when irradiated and can also during high temperature accident heating tests. Although out- of- pile laboratory tests have never hither to been able to demonstrate a diffusion process of Ag in SiC, effective diffusion coefficients have been derived to successfully reproduce measured Ag-110m releases from irradiated HTR fuel elements, compacts and TRISO particles It was found that silver transport through SiC does not proceed via bulk volume diffusion. Presently grain boundary diffusion that may be irradiation enhanced either by neutron bombardment or by the presence of fission products such as Pd, are being investigated. Recent studies of irradiated AGR-1 TRISO fuel using scanning transmission electron microscopy (STEM), transmission kukuchi diffraction (TKD) patterns and high resolution transmission electron microscopy (HRTEM) have been used to further the understanding of Ag transport through TRISO particles. No silver was observed in SiC grains, but Ag was identified at triple-points and grain boundaries of the SiC layer in the TRISO particle. Cadmium was also found in some of the very same triple junctions, but this could be related to silver behavior as Ag-110m decays to Cd-110. Palladium was identified as the main constituent of micron-sized precipitates present at the SiC grain boundaries and in most SiC grain boundaries and the potential role of Pd in the transport of Ag will be discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

RRR and thermal conductivity of Ag and Ag0.2wt%Mg alloy in Ag/Bi-2212 wires

The residual resistivity ratio (RRR) and thermal conductivity of metal matrix in metal/superconductor composite wires are important parameters for designing superconducting magnets. However, the resistivity of silver in reacted Ag/Bi-2212 wires has yet to be determined over temperature range from 4.2 K to 80 K because Bi-2212 filaments have a critical transition temperature Tc of ~ 80 K, and because it is unknown whether the RRR of Ag/Bi-2212 degrades with Cu diffusing from Bi-2212 filaments into silver sheathes at elevated temperatures and to what degree it varies with heat treatment. We measured the resistivity of stand-alone Ag and AgMg (Ag-0.2wt%Mg) wires as well as the resistivity of Ag and Ag- 0.2wt%Mg in the state-of-the-art Ag/Bi-2212 round wires reacted in 1 bar oxygen at 890 °C for 1, 8, 24 and 48 hours and quickly cooled to room temperature. The heat treatment was designed to reduce the critical current Ic of Bi-2212 wires to nearly zero while allowing Cu loss to fully manifest itself. We determined that pure silver exhibits a RRR of ~ 220 while the oxide-dispersion strengthened AgMg exhibits a RRR of ~ 5 in stand-alone samples. A surprising result is that the RRR of silver in the composite round wires doesn’t degrade with extended time at 890 °C for up to 48 hours. This surprising result may be explained by our observation that the Cu that diffuses into the silver tends to form Cu2O precipitates in oxidizing atmosphere, instead of forming Ag-Cu solution alloy. We also measured the thermal conductivity and the magneto-resistivity of pure Ag and Ag-0.2 wt%Mg from 4.2 K to 300 K in magnetic fields up to 14.8 T and summarized them using a Kohler plot.

43 PARTICLE ACCELERATORS↗

Screen-Printed Complex Ag Inks for Si HJT Metallization

Metallization using reactive metal inks has recently attracted significant research interest due to its advantages in cost of materials and manufacturing, while still achieving performance comparable to traditional fire-through particle pastes. Here, we present for the first time the use of reactive silver (Ag) inks via industrial screen-printing and inkjet printing methods for the metallization of different Si surfaces used in tunneling oxide passivating contacts (TOPCon) and Silicon heterojunction (SHJ) solar cells. Printed Ag lines exhibit a conductivity of ~5 Mu O·cm, which is approximately 3 times that of bulk Ag (1.59 µO·cm). The printed metal has a thickness of ~0.5-1.5 Mu m, an order of magnitude smaller than the current fire-through metal finger thickness (~15 Mu m). Contact resistivity measurements of the screen-printed and inkjet-printed samples on a transparent conducting oxide (TCO) surface show a very low value of ~0.2-12 mO·cm 2. Photoluminescence images of the metallized samples demonstrate minimal surface passivation degradation compared to the non-metallized areas (?iVoc <3.5 mV). Scanning electron microscopy images (SEM) reveal the structure of the printed metals on the Si surfaces as porous but much denser than fire-through Ag by nanoparticle paste. In the final presentation, we will showcase our results of printing these reactive Ag inks on high-efficiency heterojunction and TOPCon solar cells with full-area M6 wafers. Additionally, the adhesion of these reactive Ag inks on different Si surfaces according to ASTM D3359-17, as well as the performance of solar cells after standard IEC 61215 freeze/thaw and damp heat tests, will be presented. These new metal inks show promising potential as an alternative to the currently dominant particle-based pastes, offering lower Ag consumption and lower processing temperatures without compromising performance.

heterojunction solar cells↗

Bifunctional Ag@SiO 2 /Au Nanoparticles for Probing Sequential Catalytic Reactions by Surface-Enhanced Raman Spectroscopy

Here, we report the synthesis of bifunctional Ag@SiO 2 /Au nanoparticles with an “islands in the sea” configuration by titrating HAuCl 4 solution into an aqueous suspension of Ag@SiO 2 core–shell nanocubes in the presence of NaOH, ascorbic acid, and poly(vinyl pyrrolidone) at pH 11.9. The NaOH plays an essential role in generating small pores in the SiO 2 shell in situ, followed by the epitaxial deposition of Au from the Ag surface through the pores, leading to the formation of Au islands (6–12 nm in size) immersed in a SiO 2 sea. Furthermore, by controlling the amount of HAuCl 4 titrated into the reaction system, the Au islands can be made to pass through and protrude from the SiO 2 shell, embracing catalytic activity toward the reduction of 4-nitrophenol to 4-aminophenol by NaBH4. And while the Ag in the core provides a strong surface-enhanced Raman scattering activity, the SiO 2 sea helps maintain the Au component as compact, isolated, and stabilized islands. The Ag@SiO 2 /Au nanoparticles can serve as a bifunctional probe to monitor the stepwise Au-catalyzed reduction of 4-nitrothiophenol to 4-aminothiophenol by NaBH 4 and Ag-catalyzed oxidation of 4-aminothiophenol to trans-4,4'-dimercaptoazobenzene by the O 2 from air in the same reaction system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Materials Data on Ag(TeMo)6 by Materials Project

AgMo6Te6 crystallizes in the monoclinic C2/m space group. The structure is two-dimensional and consists of one AgMo6Te6 sheet oriented in the (0, 0, 1) direction. there are three inequivalent Mo sites. In the first Mo site, Mo is bonded in a 10-coordinate geometry to six Mo and four Te atoms. There are a spread of Mo–Mo bond distances ranging from 2.67–2.78 Å. There are a spread of Mo–Te bond distances ranging from 2.82–2.90 Å. In the second Mo site, Mo is bonded in a 11-coordinate geometry to six Mo, one Ag, and four Te atoms. There are one shorter (2.66 Å) and two longer (2.78 Å) Mo–Mo bond lengths. The Mo–Ag bond length is 3.26 Å. There are a spread of Mo–Te bond distances ranging from 2.83–2.89 Å. In the third Mo site, Mo is bonded in a 10-coordinate geometry to six Mo and four Te atoms. There are a spread of Mo–Te bond distances ranging from 2.80–2.87 Å. Ag is bonded in a 8-coordinate geometry to two equivalent Mo and six Te atoms. There are two shorter (2.90 Å) and four longer (3.13 Å) Ag–Te bond lengths. There are three inequivalent Te sites. In the first Te site, Te is bonded in a 4-coordinate geometry to four Mo atoms. In the second Te site, Te is bonded in a distorted hexagonal planar geometry to four Mo and two equivalent Ag atoms. In the third Te site, Te is bonded in a 5-coordinate geometry to four Mo and one Ag atom.

36 MATERIALS SCIENCE↗

Materials Data on Ag(BCl)6 by Materials Project

Ag(BCl)6 is alpha-like structured and crystallizes in the cubic Pa-3 space group. The structure is zero-dimensional and consists of eight Ag(BCl)6 clusters. Ag is bonded in a 6-coordinate geometry to six Cl atoms. There are three shorter (2.87 Å) and three longer (2.88 Å) Ag–Cl bond lengths. There are two inequivalent B sites. In the first B site, B is bonded in a single-bond geometry to one Cl atom. The B–Cl bond length is 1.79 Å. In the second B site, B is bonded in a single-bond geometry to one Cl atom. The B–Cl bond length is 1.80 Å. There are two inequivalent Cl sites. In the first Cl site, Cl is bonded in a distorted single-bond geometry to one Ag and one B atom. In the second Cl site, Cl is bonded in a distorted water-like geometry to one Ag and one B atom.

36 MATERIALS SCIENCE↗

Reversible function switching of Ag catalyst in Mg/S battery with chloride-containing electrolyte

Rechargeable Mg/S batteries suffer from fast capacity decay because of the difficult re-oxidation of MgS. To tackle this problem, we used Ag catalyst in Mg/S cells with Cl- containing electrolyte, and achieved a greatly improved specific capacity of ~1200 mAh•g -1 and a long cycling life of 100 cycles. To understand the mechanism behind this improvement, we employed in-situ synchrotron radiation X-ray diffraction and in-situ X-ray absorption spectroscopy tools to study the reversible phase transitions during charge/discharge cycling. Additionally, the in-situ experiment results revealed that, at deeply charged state, Ag reacted with Cl- in the electrolyte to form the AgCl interfacial layer which prevented the physical contact of Ag with elemental S and avoided the formation of Ag 2 S; at early discharged state, AgCl transformed back to metallic Ag, which guaranteed its catalytic effectiveness for MgS decomposition. This reversible function switching mechanism of Ag catalyst is completely different from that in Mg/S cells using other catalysts or electrolytes.

25 ENERGY STORAGE↗

On the image of AGS 3 He 2+ $\vec{n}$ 0 in the blue

This note addresses the transport of Helion spin $\vec{n}$ 0 vector, from its periodic orientation in the AGS to RHIC Blue ring injection kicker, via the AGS extraction system and the AtR line. The goal is to investigate optimal injection energy into RHIC, in the matter of Helion spin matching, in the hypothesis of equal warm and cold snake strengths in the AGS. The study uses recently computed OPERA 3-D field maps of the AGS cold snake, including possibility of independent solenoid and helix settings (as discussed in Tech. Note C-A/AP/485), together with the machinery of the AGS and AtR models developed in the stepwise ray-tracing code Zgoubi. Computing tools and methods employed are discussed as well, in order to facilitate possible further checks or investigations. They are however similar to those used in an earlier study regarding the image in RHIC Blue and Yellow of AGS $\vec{n}$ 0 via the AtR in the case of proton beam (Tech. Note C-A/AP/502), which can be referred to for additional details.

43 PARTICLE ACCELERATORS↗

Simulation of 6 to 3 to 1 merge and squeeze of Au77+ bunches in AGS

In order to increase the intensity per Au77+ bunch at AGS extraction, a 6 to 3 to 1 merge scheme was developed and implemented by K. Zeno during the 2016 RHIC run. For this scheme, 12 Booster loads, each consisting of a single bunch, are delivered to AGS per AGS magnetic cycle. The bunch from Booster is itself the result of a 4 to 2 to 1 merge which is carried out on a flat porch during the Booster magnetic cycle. Each Booster bunch is injected into a harmonic 24 bucket on the AGS injection porch. In order to fit into the buckets and allow for the AGS injection kicker rise time, the bunch width must be reduced by exciting quadrupole oscillations just before extraction from Booster. The bunches are injected into two groups of six adjacent harmonic 24 buckets. In each group the 6 bunches are merged into 3 by bringing on RF harmonic 12 while reducing harmonic 24. This is a straightforward 2 to 1 merge (in which two adjacent bunches are merged into one). One ends up with two groups of three adjacent bunches sitting in harmonic 12 buckets. These bunches are accelerated to an intermediate porch for further merging. Doing the merge on a porch that sits above injection energy helps reduce losses that are believed to be due to the space-charge force acting on the bunched particles. (The 6 to 3 merge is done on the injection porch because the harmonic 24 frequency on the intermediate porch would be too high for the AGS RF cavities.) On the intermediate porch each group of 3 bunches is merged into one by bringing on RF harmonics 8 and 4 and then reducing harmonics 12 and 8. One ends up with 2 bunches, each the result of a 6 to 3 to 1 merge and each sitting in a harmonic 4 bucket. This puts 6 Booster loads into each bunch. Each merged bunch needs to be squeezed into a harmonic 12 bucket for subsequent acceleration. This is done by again bringing on harmonic 8 and then harmonic 12. Results of simulations of the 6 to 3 to 1 merge and the subsequent squeeze into harmonic 12 buckets are presented in this note. In particular, they provide a benchmark for what can be achieved with the available RF voltages.

43 PARTICLE ACCELERATORS↗