Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “waveform analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Geomagnetically Induced Current Field Test on Large Grid-Connected Power Transformers: Analysis, Model Development, and Simulations

Geomagnetic-induced current (GIC) flow in power grids can cause undesirable effects such as transformer overheating, harmonics, higher reactive power demand, etc. Many simulation models have been developed to study these effects, but real-world verification on modern transformer designs is rare. Here, this paper presents the first long-duration GIC field test in the U.S. performed on high-voltage, grid-connected transformers featuring winding clamps and tie rods instead of conventional tie bars. Field measurements were taken to evaluate GIC effects. These measurements also aided in developing and validating thermal and electromagnetic transient (EMT) models of the transformers. During the test, significant current and voltage distortions were observed along with considerable transformer reactive power losses. Analysis of the field measurements showed that the transformers’ hottest spot was at the inner windings, and their k-factors were close to factory test and software default values. Thermal simulations indicated that the transformers would not violate their thermal limits even for a GIC waveform that peaks at about 200 A/phase. EMT simulations revealed that increased transformer loading may reduce GIC-induced reactive power demand and harmonics in certain scenarios. The study also highlighted potential inaccuracies in using the k-factor method to calculate transformer reactive power losses.

EMTDC↗
NASA NTRS1980

Incipient Failure Detection (IFD) of antifriction ball bearings

Two methods were investigated for retrieving the ball bearing signals buried by the overall signature of an operating large engine such as the main space shuttle engine. The signal averaging method averages n** signals over a time duration equaling the known period of the ball bearing defect frequency. With this method, the desired ball bearing defect signal will be enhanced over the noise by a factor of the square root of n. A second method is to perform a further frequency analysis on the logarithmic spectrum in order to detect and separate different families of harmonics and sidebands, thereby giving information about modulating frequencies. These two alternate IFD methods were carried out with a Norland 3001 waveform and data system. The obtained results are then compared with the power spectral density (PSD) of the overall machine signals and conclusions are made accordingly.

Wang, D. Y.↗
NASA NTRS1982

Pulsed multiwavelength laser ranging system

A pulsed multiwavelength laser ranging system for measuring atmospheric delay was built and tested, and its theoretical performance limits were calculated. The system uses a dye modelocked ND:YAG laser, which transmits 70 psec wide pulses simultaneously at 1064, 532, and 355 nm. The differential delay of the 1064 and 355 nm pulses is measured by a specially calibrated waveform digitizer to estimate the dry atmospheric delay. The delay time of the 532 nm pulse is used to measure the target distance. Static crossed field photomultipliers are used as detectors for all wavelengths. Theoretical analysis shows that path curvature and atmospheric turbulence are fundamental limits to the ranging accuracy of both single and multicolor systems operating over horizontal paths. For two color systems, an additional error is caused by the uncertainty in the path averaged water vapor. The standard deviation of the multicolor instrument's timing measurements is directly proportional to the laser pulse width plus photomultiplier jitter divided by the square root of the received photoelectron number. The prototype system's maximum range is km, which is limited by atmospheric and system transmission losses at 355 nm. System signal detection and false alarm calculations are also presented.

Abshire, J. B.↗
NASA NTRS1989

Blade surface pressure measurement on a pusher propeller in flight

Unsteady aerodynamics of a pusher propeller operating in the wake of a pylon is investigated through analysis of flight test data. Twenty-two surface-mounted miniature pressure transducers were installed at the 75 and 90 percent radius locations on a propeller blade on a test-bed aircraft. Twenty-six different flight conditions were flown to cover the range of speeds, rpm, altitudes, and flap positions encountered by an advanced turboprop general aviation aircraft. Preliminary analysis of the flight test data indicate a strong three-dimensionality to the perturbed flow at the 75 and 90 percent radii due to pylon wake encounter. Time-history of the pressure transducer waveforms recorded for 700 revolutions exhibit a one-per-cycle wave oscillation on the wake signature. No explanation is found for this behavior yet.

Farokhi, S.↗
NASA NTRS1992

Sea surface mean square slope from Ku-band backscatter data

A surface mean-square-slope parameter analysis is conducted for 14-GHz airborne radar altimeter near-nadir, quasi-specular backscatter data, which in raw form obtained by least-squares fitting of an optical scattering model to the return waveform show an approximately linear dependence over the 7-15 m/sec wind speed range. Slope data are used to draw inferences on the structure of the high-wavenumber portion of the spectrum. A directionally-integrated model height spectrum that encompasses wind speed-dependent k exp -5/2 and classical Phillips k exp -3 power laws subranges in the range of gravity waves is supported by the data.

Jackson, F. C.↗
NASA NTRS2008

Signal Analysis Algorithms for Optimized Fitting of Nonresonant Laser Induced Thermal Acoustics Damped Sinusoids

This study seeks a numerical algorithm which optimizes frequency precision for the damped sinusoids generated by the nonresonant LITA technique. It compares computed frequencies, frequency errors, and fit errors obtained using five primary signal analysis methods. Using variations on different algorithms within each primary method, results from 73 fits are presented. Best results are obtained using an AutoRegressive method. Compared to previous results using Prony s method, single shot waveform frequencies are reduced approx.0.4% and frequency errors are reduced by a factor of approx.20 at 303K to approx. 0.1%. We explore the advantages of high waveform sample rates and potential for measurements in low density gases.

Balla, R. Jeffrey↗
DOE OSTI2020

Applying Compression-Based Metrics to Seismic Data in Support of Global Nuclear Explosion Monitoring

The analysis of seismic data for evidence of possible nuclear explosion testing is a critical global security mission that relies heavily on human expertise to identify and mark seismic signals embedded in background noise. To assist analysts in making these determinations, we adapted two compression distance metrics for use with seismic data. First, we demonstrated that the Normalized Compression Distance (NCD) metric can be adapted for use with waveform data and can identify the arrival times of seismic signals. Then we tested an approximation for the NCD called Sliding Information Distance (SLID), which can be computed much faster than NCD. We assessed the accuracy of the SLID output by comparing it to both the Akaike Information Criterion (AIC) and the judgments of expert seismic analysts. Our results indicate that SLID effectively identifies arrival times and provides analysts with useful information that can aid their analysis process.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
NASA NTRS1981

Terrain profiling from Seasat altimetry

To determine their applicability for terrain profiling, Seasat altimeter measurements were analyzed for the following geographic areas: (1) Andean salars of southern Bolivia; (2) Alaska; (3) south-central Arizona; (4) imperial Valley of California; (5) Yuma Valley of Arizona; and (6) Great Salt Lake Desert. Analysis of the data over all of these geographic areas shows that the satellite altimeter servo did not respond quickly enough to changing terrain features. However, it is demonstrated that retracking of the archived surface return waveforms yields surface elevations over smooth terrain accurate to + or - 1 m when correlated with large scale maps. The retracking algorithm used and its verification over the salars of southern Bolivia are described. Results are presented for each of the six geographic areas.

Brooks, R. L.↗
NASA NTRSDate not supplied

Uncertainty Quantification of CFD Model Assumptions Against Sonic Boom Noise Prediction of a Commercial Supersonic Transport

This paper presents the results of uncertainty modeling of sonic boom noise generation from commercial supersonic transport considering the Spalart-Allmaras (SA) turbulence modeling parameters as well as Mach number, angle of attack and altitude. Sample generation and analysis for this uncertainty model was performed by UQPCE, which is a software package developed at the NASA Langley Research Center. To build the uncertainty model, 42 cases of sonic boom noise calculation were performed. Computation of the ground noise can be briefly summarized in two steps. First, the near field pressure waveforms are sampled from CFD calculation using the NASA Langley’s FUN3D solver. Second, this information is passed to an atmospheric propagation code, sBOOM, which solves an augmented Burger’s equation and simulates how the near field waveforms will change while passing through the atmosphere. The ground signature is further processed to obtain the perceived loudness, PLdB. Having a high spatial resolution near the shockwave in the CFD calculation is critical in sonic boom noise prediction. Because the variation in the input parameters for the current uncertainty quantification (UQ) study is likely to lead to change in shock location, angle and strength, the grid adaptation for shock capturing is independently applied for each condition. The final mesh used in the CFD calculation consists of approximately 420 million cells. The pressure signatures are sampled at three, four and five body lengths away from the aircraft to make sure the three dimensional effects around the aircraft are resolved. The results of the UQ analysis shows that within the three aleatory variables, the angle of attack had the most impact against ground noise, followed by the altitude and the Mach number. Between the two SA model parameters, the Kármán constant (𝜅) was significantly more important than the turbulent Prandtl number (𝜎), but these two parameters were only marginally significant in the overall prediction variance in ground noise. The UQ procedure explained in this paper can be widely applied to other model parameters.

Uncertainty Quantification↗
NASA NTRSDate not supplied

Uncertainty Quantification of CFD Model Assumptions Against Sonic Boom Noise Prediction of a Commercial Supersonic Transport

This paper presents the results of uncertainty modeling of sonic boom noise generation from commercial supersonic transport considering the Spalart-Allmaras (SA) turbulence modeling parameters as well as Mach number, angle of attack and altitude. Sample generation and analysis for this uncertainty model was performed by UQPCE, which is a software package developed at the NASA Langley Research Center. To build the uncertainty model, 42 cases of sonic boom noise calculation were performed. Computation of the ground noise can be briefly summarized in two steps. First, the near field pressure waveforms are sampled from CFD calculation using the NASA Langley’s FUN3D solver. Second, this information is passed to an atmospheric propagation code, sBOOM, which solves an augmented Burger’s equation and simulates how the near field waveforms will change while passing through the atmosphere. The ground signature is further processed to obtain the perceived loudness, PLdB. Having a high spatial resolution near the shock wave in the CFD calculation is critical in sonic boom noise prediction. Because the variation in the input parameters for the current uncertainty quantification (UQ) study is likely to lead to change in shock location, angle and strength, the grid adaptation for shock capturing is independently applied for each condition. The final mesh used in the CFD calculation consists of approximately 420 million cells. The pressure signatures are sampled at three, four and five body lengths away from the aircraft to make sure the three dimensional effects around the aircraft are resolved. The results of the UQ analysis shows that within the three aleatory variables, the angle of attack had the most impact against ground noise, followed by the altitude and the Mach number. Between the two SA model parameters, the Kármán constant (𝜅) was significantly more important than the turbulent Prandtl number (𝜎), but these two parameters were only marginally significant in the overall prediction variance in ground noise. The UQ procedure explained in this paper can be widely applied to other model parameters.

Uncertainty Quantifications↗
DOE OSTI2022

Strong Upper-Plate Heterogeneity at the Hikurangi Subduction Margin (North Island, New Zealand) Imaged by Adjoint Tomography

We use earthquake-based adjoint tomography to invert for three-dimensional structure of the North Island, New Zealand, and the adjacent Hikurangi subduction zone. The study area, having a shallow depth to the plate interface below the North Island, offers a rare opportunity for imaging material properties at an active subduction zone using land-based measurements. Starting from an initial model derived using ray tomography, we perform iterative model updates using spectral element and adjoint simulations to fit waveforms with periods ranging from 4–30 s. We perform 28 model updates using an L-BFGS optimization algorithm, improving data fit and introducing P- and S-wave velocity changes of up to ±30%. Resolution analysis using point spread functions show that our measurements are most sensitive to heterogeneities in the upper 30 km. The most striking velocity changes coincide with areas related to the active Hikurangi subduction zone. Lateral velocity structures in the upper 5 km correlate well with New Zealand geology. Here, the inversion reveals increased along-strike heterogeneity on the margin. In Cook Strait we observe a low-velocity zone interpreted as deep sedimentary basins. In the central North Island, low-velocity anomalies are linked to surface geology, and we relate velocity structures at depth to crustal magmatic activity below the Taupō Volcanic Zone.

58 GEOSCIENCES↗
NASA NTRS1983

SEASAT radar altimeter measurements over the Florida Everglades

The SEASAT satellite radar altimeter traversed the Florida Everglades on August 14, 1978. Analysis of the measurements disclosed that the altimeter pulses from 800 km above the Earth's surface penetrated the vegetation canopies to provide land and water surface elevations with accuracies better than + or - 50 cm. The altimeter waveforms required retracking over the specular Everglades surface. The altimeter-derived land elevations were correlated with large-scale topographic maps while the altimeter-derived water elevations were correlated with water gauge records of the U.S. Geological Survey. Examination of the altimeter waveforms also revealed reflections from the Everglades' surface occurring earlier than the surface reflections. These earlier surface reflections are interpreted to be from vegetation canopies, and may provide a measure of vegetation canopy heights. Future satellite radar altimeters could provide supplemental vertical control in relatively inaccessible swamp areas, could monitor water levels, and perhaps could monitor vegetation growth.

Brooks, R. L.↗
NASA NTRS1999

Acoustic Reflection and Transmission of 2-Dimensional Rotors and Stators, Including Mode and Frequency Scattering Effects

A reduced order modeling scheme has been developed for the unsteady acoustic and vortical coupling between blade rows of a turbomachine. The essential behavior of the system is governed by modal scattering coefficients (i.e., reflection and transmission coefficients) of the rotor, stator, inlet and nozzle, which are calculated as if they were connected to non-reflecting ducts. The objective of this report is to identify fundamental behavior of these scattering coefficients for a better understanding of the role of blade row reflection and transmission in noise generation. A 2D flat plate unsteady cascade model is used for the analysis with the expectation that the general behavior presented herein will carry over to models that include more realistic flow and geometry. It is shown that stators scatter input waves into many modes at the same frequency whereas rotors scatter on frequency, or harmonic order. Important cases are shown here the rotor reflection coefficient is greater than unity; a mode at blade passing frequency (BPF) traveling from the stator with unit sound power is reflected by the rotor with more than unit power at 2xBPF and 3xBPE Analysis is presented to explain this unexpected phenomenon. Scattering curves are presented in a format chosen for design use and for physical interpretation. To aid in interpretation of the curves, formulas are derived for special condition where waveforms are parallel to perpendicular to the rotor.

Hanson, Donald B.↗
NASA NTRS1996

An AWE Implementation for Electromagnetic Analysis

Although full wave electromagnetic systems are large and cumbersome to solve, typically only a few parameters, such as input impedance, S parameters, and far field pattern, are needed by the designer or analyst. A reduced order modeling of these parameters is therefore an important consideration in minimizing the the CPU requirements. The Asymptotic Waveform Evaluation (AWE) method is one approach to construct a reduced order model of the input impedance or other useful electromagnetic parameters. We demonstrate its application and validity when used in conjunction with the finite element method to simulate full wave electromagnetic problems.

Gong, Jian↗
DOE OSTI2021

Novel technique for the study of pileup events in cryogenic bolometers

Precise characterization of detector time resolution is of crucial importance for next-generation cryogenic-bolometer experiments searching for neutrinoless double-beta decay, such as CUPID, in order to reject background due to pile-up of two-neutrino double-beta decay events. In this paper, we describe a technique developed to study the pile-up rejection capability of cryogenic bolometers. Our approach, which consists of producing controlled pile-up events with a programmable waveform generator, has the benefit that we can reliably and reproducibly control the time separation and relative energy of the individual components of the generated pile-up events. The resulting data allow us to optimize and benchmark analysis strategies to discriminate between individual and pile-up pulses. We describe a test of this technique performed with a small array of detectors at the Laboratori Nazionali del Gran Sasso, in Italy; we obtain a 90% rejection efficiency against pulser-generated pile-up events with rise time of ~15 ms down to time separation between the individual events of 2 ms.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Characterization of Infrasonic Signatures of Earth-Grazing Fireballs as Analogues to Hypersonic Vehicles (Final Report)

Accurate detection, discrimination, and characterization of high-altitude hypersonic events using infrasonic monitoring are critical to planetary defense and global strategic surveillance. This report synthesizes recent advances achieved through rigorous analysis of infrasonic signatures from natural meteoroids, emphasizing shallow entry-angle meteoroids as essentially proxies for artificial hypersonic systems. Meteoroids naturally encompass diverse velocities, trajectories, altitudes, and fragmentation behaviors, enabling systematic validation of empirical period–yield relationships, waveform morphology classifiers, and trajectory-induced back-azimuth deviation models. Integration of adaptive array-processing enhancements within Cardinal software further extends infrasonic detection sensitivity and signal classification reliability. Collectively these advances, based solely on infrasonic signatures or limited optical data, offer robust methodologies for distinguishing natural from artificial hypersonic sources, significantly reducing event geolocation uncertainties and refining source-function determination. The outcomes detailed herein lay foundational groundwork for improved global hypersonic event-surveillance frameworks, supporting improved security preparedness and informing strategic monitoring and defense policies.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1983

Seismicity, fault plane solutions, depth of faulting, and active tectonics of the Andes of Peru, Ecuador, and southern Colombia

The long-period P waveforms observed for 17 earthquakes in the Peruvian Andes during 1963-1976 are compared with synthetic waveforms to obtain fault-plane solutions and focal depths. The morphological units of the Peruvian Andes are characterized: coastal plains, Cordillera Occidental, altiplano and central high plateau, Cordillera Oriental, and sub-Andes. The data base and analysis methodology are discussed, and the results are presented in tables, diagrams, graphs, maps, and photographs illustrating typical formations. Most of the earthquakes are shown to occur in the transition zone from the sub-Andes to the Cordillera Oriental under formations of about 1 km elevation at focal depths of 10-38 km. It is suggested that the sub-Andean earthquakes reflect hinterland deformation of a detached fold and thrust belt, perhaps like that which occurred in parts of the Canadian Rockies. From the total crustal shortening evident in Andean morphology and the shortening rate of the recent earthquakes it is estimated that the topography and crustal root of the Andes have been formed during the last 90-135 Myr.

Suarez, G.↗
NASA NTRS2006

High-Performance Scanning Acousto-Ultrasonic System

A high-performance scanning acousto-ultrasonic system, now undergoing development, is designed to afford enhanced capabilities for imaging microstructural features, including flaws, inside plate specimens of materials. The system is expected to be especially helpful in analyzing defects that contribute to failures in polymer- and ceramic-matrix composite materials, which are difficult to characterize by conventional scanning ultrasonic techniques and other conventional nondestructive testing techniques. Selected aspects of the acousto-ultrasonic method have been described in several NASA Tech Briefs articles in recent years. Summarizing briefly: The acousto-ultrasonic method involves the use of an apparatus like the one depicted in the figure (or an apparatus of similar functionality). Pulses are excited at one location on a surface of a plate specimen by use of a broadband transmitting ultrasonic transducer. The stress waves associated with these pulses propagate along the specimen to a receiving transducer at a different location on the same surface. Along the way, the stress waves interact with the microstructure and flaws present between the transducers. The received signal is analyzed to evaluate the microstructure and flaws. The specific variant of the acousto-ultrasonic method implemented in the present developmental system goes beyond the basic principle described above to include the following major additional features: Computer-controlled motorized translation stages are used to automatically position the transducers at specified locations. Scanning is performed in the sense that the measurement, data-acquisition, and data-analysis processes are repeated at different specified transducer locations in an array that spans the specimen surface (or a specified portion of the surface). A pneumatic actuator with a load cell is used to apply a controlled contact force. In analyzing the measurement data for each pair of transducer locations in the scan, the total (multimode) acousto-ultrasonic response of the specimen is utilized. The analysis is performed by custom software that extracts parameters of signals in the time and frequency domains. The computer hardware and software provide both real-time and postscan processing and display options. For example, oscilloscope displays of waveforms and power spectral densities are available in real time. Images can be computed while scanning continues. Signals can be digitally preprocessed and/or post-processed by filtering, windowing, time-segmenting, and running-waveform-averaging algorithms. In addition, the software affords options for off-line simulation of the waveform-data-acquisition and scanning processes. In tests, the system has been shown to be capable of characterizing microstructural changes and defects in SiC/SiC and C/SiC ceramic-matrix composites. Delaminations, variations in density, microstructural changes attributable to infiltration by silicon, and crack-space indications (defined in the next sentence) have been revealed in images formed from several time- and frequency-domain parameters of scanning acousto-ultrasonic signals. The crack-space indications were image features that were not revealed by other nondestructive testing methods and are so named because they turned out to mark locations where cracking eventually occurred.

Roth, Don↗