Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “use cases”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Software For Analysis Of Reliability, Redundancy, And Cost

CARRAC is software tool for combined analysis of reliability, redundancy, and cost of alternative choices of subsystem that is part of larger system. Uses various parameters entered from computer keyboard to determine subsystem and redundancy method (if any) that minimizes cost. Also, calculation selected from five different mathematical models that enable application of CARRAC to wide variety of cases. Uses parameters to calculate and compare total expected cost for alternatives of a chosen subsystem. Written in Microsoft Quick-Basic v4.5.

Patterson, R. L.↗
NASA NTRS1994

Navier-Stokes Calculations for a Highly-Twisted Rotor Near Stall

The viscous flow field near the surface of a hovering rotor blade was studied for blade twist distributions typical of a till rotor blade and a conventional helicopter rotor blade. Three blade geometries were studied, including a tilt rotor blade twist distribution (baseline), conventional helicopter rotor blade twist distribution, and the baseline twist distribution with 2 deg of precone. The results give insight into the delayed stall phenomenon often observed for highly twisted rotors. Calculations were performed for a high thrust condition near stall using the thin-layer Navier-Stokes CFD code TURNS. Effects of built-in twist on section force coefficients, skin friction, velocities, surface pressures, and boundary layer shape factor are discussed. Although the rotor thrust coefficient was nominally the same for the cases using the two twist distributions, large differences were found in the section in-plane and normal force coefficients. These preliminary results imply that the blade outboard region, rather than the inboard region, provides the majority of the performance advantage of the baseline case over the low twist case. Skin friction, velocities near the blade, and surface pressures for the two twist distributions reveal significant differences in the blade outboard region.

Yamauchi, Gloria K.↗
NASA NTRS1992

Analysis of an RNG based turbulence model for separated flows

A two-equation turbulence model of the K-epsilon type was recently derived by using Renormalization Group (RNG) methods. It was later reported that this RNG based model yields substantially better predictions than the standard K-epsilon model for turbulent flow over a backward facing step - a standard test case used to benchmark the performance of turbulence models in separated flows. The improvements obtained from the RNG K-epsilon model were attributed to the better treatment of near wall turbulence effects. In contrast to these earlier claims, it is shown in this paper that the original version of the RNG K-epsilon model substantially underpredicts the reattachment point in the backstep problem. This is a deficiency that is traced to the modeling of the production of dissipation term. However, with the most recent improvements in the RNG K-epsilon model, excellent results for the backstep problem are now obtained.

Speziale, C. G.↗
NASA NTRS1996

TPS Sizing for Access-to-Space Vehicles

A study was carried out to identify, develop, and benchmark simulation techniques needed for optimum thermal protection system (TPS) material selection and sizing for reusable launch vehicles. Fully viscous, chemically reacting, Navier-Stokes flow solutions over the Langley wing-body single stage to orbit (SSTO) configuration were generated and coupled with an in-depth conduction code. Results from the study provide detailed TPS heat shield materials selection and thickness sizing for the wing-body SSTO. These results are the first ever achieved through the use of a complete, trajectory based hypersonic, Navier-Stokes solution database. TPS designs were obtained for both laminar and turbulent entry trajectories using the Access-to-Space baseline materials such as tailorable advanced blanket insulation. The TPS design effects (materials selection and thickness) of coupling material characteristics to the aerothermal environment are illustrated. Finally, a sample validation case using the shuttle flight database is included.

Henline, William↗
NASA NTRS1995

SSBRP User Operations Facility (UOF) Overview and Development Strategy

This paper will present the Space Station Biological Research Project (SSBRP) User Operations Facility (UOF) architecture and development strategy. A major element of the UOF at NASA Ames Research Center, the Communication and Data System (CDS) will be the primary focus of the discussions. CDS operational, telescience, security, and development objectives will be discussed along with CDS implementation strategy. The implementation strategy discussions will include: Object Oriented Analysis & Design, System & Software Prototyping, and Technology Utilization. A CDS design overview that includes: CDS Context Diagram, CDS Architecture, Object Models, Use Cases, and User Interfaces will also be presented. CDS development brings together "cutting edge" technologies and techniques such as: object oriented development, network security, multimedia networking, web-based data distribution, JAVA, and graphical user interfaces. Use of these "cutting edge" technologies and techniques translates directly to lower development and operations costs.

Picinich, Lou↗
NASA NTRSDate not supplied

The LuNaMaps Project: Advancing Capabilities for Developing and Validating Digital Elevation Models of Rocky Surfaces from Orbital Data

Both navigation and surface science can benefit from the ability to generate high resolution and accurate maps of the surface of the Moon and other solar system bodies. The primary way these maps are generated is through the use of orbital imagery and ranging data. Traditionally, the process of using orbital imagery and ranging data is tedious and labor-intensive. Additionally, once maps have been built, there has generally been limited effort in developing standards by which to verify the accuracy and quality of the generated maps. The Lunar Navigation Maps (LuNaMaps) project is a NASA Game Changing Development (GCD) project which over the last 4 years has aimed to address these issues both for the Moon and for other rocky solar system bodies. This has been accomplished through development of new and existing capabilities including: a suite of methods and tools to combine all sources of orbital imagery; a benchmark data set as well as basic requirements for high-fidelity simulations of precision landing functions; tools to synthetically enhance map products with lander-scale features for use in the development and testing of hazard detection systems; methods and tools to evaluate the accuracy of developed digital elevation maps (DEMs) and their quality for use in terrain relative navigation scenarios; and tools to realistically render image and lidar data. In this work, we provide an overview of the capabilities developed through LuNaMaps, demonstrating its use for processing existing lunar data, and describing how it can be applied to other use cases. We additionally provide preliminary results showing the application of the developed tools and processes to the generation of elevation maps of the Lunar Surface Proving Grounds (LSPG) lunar analog at Astrobotic’s Mojave testing facility using “orbital imagery” captured by a drone. In this terrestrial demonstration, we have the benefit of being able to compare the results to a ground truth model of the LSPG. We finally describe plans to use the newly created maps in a terrestrial terrain relative navigation demonstration over the LSPG in early 2025.

optical navigation↗
NASA NTRS2012

Programmatic Impact of SDRAM SEFI

The Elpida EDS5104(08)ABTA 512Mb SDRAM is examined for programmatic impact of SEE. Use cases for the devices including EDAC and mode register reload are examined. Results indicate some SEE mitigation methods require careful application to achieve system-level benefits, while some event types are essentially mitigated by the application use. In the studied devices MBE and SEFI are identified and investigated as mechanisms requiring special consideration.

Single Event Functionality Interrupt (SEFI)↗
NASA NTRSDate not supplied

Optimization Algorithms as Quantum Performance Benchmarks

Combinatorial optimization is anticipated to be one of the primary use cases for quantum computation in the coming years. The Quantum Approximate Optimization Algorithm (QAOA) and Quantum Annealing (QA) have the potential to demonstrate significant run-time performance benefits over current state-of-the-art solutions. Using existing methods for characterizing classical optimization algorithms, we analyze solution quality obtained by solving Max-Cut problems using a quantum annealing device and gate-model quantum simulators and devices. This is used to guide the development of an advanced benchmarking framework for quantum computers designed to evaluate the trade-off between run-time execution performance and the solution quality for iterative hybrid quantum-classical applications. The framework generates performance profiles through effective visualizations that show performance progression as a function of time for various problem sizes and illustrates algorithm limitations uncovered by the benchmarking approach. The framework is an enhancement to the existing open-source QED-C Application-Oriented Benchmark suite and can connect to the open-source analysis libraries. The suite can be executed on various quantum simulators and quantum hardware systems.

benchmarking↗
NASA NTRS1983

Space Shuttle propulsion parameter estimation using optimal estimation techniques

This fourth monthly progress report again contains corrections and additions to the previously submitted reports. The additions include a simplified SRB model that is directly incorporated into the estimation algorithm and provides the required partial derivatives. The resulting partial derivatives are analytical rather than numerical as would be the case using the SOBER routines. The filter and smoother routine developments have continued. These routines are being checked out.

Source record↗
NASA NTRS2005

High Resolution Aerospace Applications using the NASA Columbia Supercomputer

This paper focuses on the parallel performance of two high-performance aerodynamic simulation packages on the newly installed NASA Columbia supercomputer. These packages include both a high-fidelity, unstructured, Reynolds-averaged Navier-Stokes solver, and a fully-automated inviscid flow package for cut-cell Cartesian grids. The complementary combination of these two simulation codes enables high-fidelity characterization of aerospace vehicle design performance over the entire flight envelope through extensive parametric analysis and detailed simulation of critical regions of the flight envelope. Both packages. are industrial-level codes designed for complex geometry and incorpor.ats. CuStomized multigrid solution algorithms. The performance of these codes on Columbia is examined using both MPI and OpenMP and using both the NUMAlink and InfiniBand interconnect fabrics. Numerical results demonstrate good scalability on up to 2016 CPUs using the NUMAIink4 interconnect, with measured computational rates in the vicinity of 3 TFLOP/s, while InfiniBand showed some performance degradation at high CPU counts, particularly with multigrid. Nonetheless, the results are encouraging enough to indicate that larger test cases using combined MPI/OpenMP communication should scale well on even more processors.

Mavriplis, Dimitri J.↗
NASA NTRS2018

Adaptive Load Control of Flexible Aircraft Wings Using Fiber Optic Sensing

Over the past century aircraft wing design has transformed from the morphing wing used on the Wright Flyer to rigid wings with little to no shape-tailoring abilities. Modern day wings are designed to fly at a single trim condition and optimized to have a maximum aerodynamic efficiency at only this condition. Shape morphing wings on the other hand have the potential to undergo geometric changes allowing them to adapt to their mission profiles. Several flight demonstrations have been conducted over the decades using morphing-wing technologies. Active wing-twist control was demonstrated on the X-53 Active Aeroelastic Wing (AAW) research project by utilizing multiple leading- and trailing-edge control surfaces. Passive morphing technology has been demonstrated on the Rockwell RPRV-870 Highly Maneuverable Aircraft Technology (HiMAT) aircraft. In the current study, the wings of a small unmanned aerial system (sUAS) were modified to have segmented control surfaces (SCS). The modifications include segmenting the original wing control surfaces (one flap and one aileron per wing) into 44 individual sections, each section having its own independent servo control motor. The wings were also instrumented with a network of over 1800 fiber-optic strain sensors (on four sensing fibers distributed over the top and bottom surfaces of the wing) monitoring the strain response of the wing to aerodynamic loading. The SCS positions were manipulated in real time to modify the spanwise lift distribution of the wings on the sUAS. The change in the structural response of the wings caused by load redistribution was quantified by measuring the bending strains on the upper and lower wing surfaces using an on-board compact fiber-optic strain sensing (cFOSS) system. A feedback controller was developed to control the SCS positions using strain-based shape estimations from the Displacement Transfer Function (DTF). Post-processing of the strain data allowed for the transverse displacement distributions and load distributions to be compared for the conventional and segmented control surface cases using displacements and loads algorithms developed by Richards and Ko at AFRC (refs. 5-10). While the current study focused on the shifting of the spanwise aerodynamic loads as quantified by displacements, future applications for loads or displacement control might include active gust alleviation and flutter suppression.

Pena, Francisco↗
NASA NTRSDate not supplied

Openet: Applications of Satellite-Based Evapotranspiration Data for Water Resources Management in the Western United States

Advancing water security in overallocated river basins globally requires consistent and reproducible information on consumptive use of water that can anchor the development of data-driven solutions to the challenge of balancing water supply and demand. OpenET is a fully automated system for field-scale (30 m), satellite-based mapping of evapotranspiration (ET) at daily, monthly and annual timesteps. OpenET currently provides spatially contiguous data throughout the 23 westernmost states in the continental US, and includes both current information as well as multi-year timeseries of ET. The OpenET consortium has implemented an ensemble of satellite-based ET models (ALEXI/DisALEXI, eeMETRIC, PT-JPL, geeSEBAL, SIMS and SSEBop) on Google Earth Engine, which provides a shared computing platform for collaboration on processing of data from Landsat and other satellites, land cover and meteorological inputs, leading to increased consistency and accuracy across the ensemble of models. Earth Engine also facilitates hosting and distribution of data via open data collections and an application programming interface. We provide updates on the OpenET framework, open data services and data access tools, approach to geographic expansion, recent accuracy assessments, and describe how a user-driven design approach has facilitated successful applications of OpenET data for a wide range of water resource management activities. Applications to date include: use of ET data to improve quantification of ET and consumptive use in Oregon, Utah and the Upper Colorado River Basin; streamlining of water use reporting requirements in the California Delta; support for calculation of water budgets for the implementation of the Sustainable Groundwater Management Act in California; and integration into decision support tools for irrigation management. The use cases demonstrate how satellite-derived ET data that are easily accessed and seen as broadly accepted can accelerate adoption of innovative water management practices at scale, and support advances in the sustainability of water supplies. Uptake and use of data by the OpenET science community has also led to advances in our understanding of the impacts of landcover change, irrigation intensification and wildfire events on hydrology and the water security.

Applications↗
NASA NTRS1999

Testing and Analysis of Composite Skin/Stringer Debonding Under Multi-Axial Loading

Damage mechanisms in composite bonded skin/stringer constructions under uniaxial and biaxial (in-plane/out- of-plane) loading conditions were examined. Specimens consisted of a tapered composite flange bonded onto a composite skin. Tests were performed under monotonic loading conditions in tension, three-point bending, and combined tension/bending . For combined tension/bending testing, a unique servohydraulic load frame was used that was capable of applying both in-plane tension and out-of-plane bending loads simultaneously. Specimen edges were examined on the microscope to document the damage occurrence and to identify typical damage patterns. The observations showed that, for all three load cases, failure initiated in the flange, near the flange tip, causing the flange to almost fully debond from the skin. A two-dimensional plane-strain finite element model was developed to analyze the different test cases using a geometrically nonlinear solution. For all three loading conditions, principal stresses exceeded the transverse strength of the material in the flange area. Additionally, delaminations of various lengths were simulated in two locations where delaminations were observed. The analyses showed that unstable delamination propagation is likely to occur in one location at the loads corresponding to matrix ply crack initiation for all three load cases.

Krueger, Ronald↗
NASA NTRSDate not supplied

Comparison between Computational and Experimental Wall-Shear Stress and Pressure Measurements in a Supersonic Wind Tunnel

We study the performance of two selected RANS models (SST-$k$-$\omega$ and Baldwin-Lomax) to simulate the mean wall-shear and pressure data obtained from a distributed-roughness-related experimental campaign conducted at Ahmic Aerospace, LLC, located in Ohio, US. A structured compressible Navier-Stokes in-house solver, DPLR, is used to conduct the RANS simulations. As the final objective is to perform the studies under high-enthalpy flow conditions, such as inside the AHF facility at NASA-Ames Research Center (ARC), the current investigation focuses on the low-enthalpy cases using Ahmic's high-Reynolds-number supersonic wind tunnel as the initial step to simplify the flow physics. Furthermore, the wind tunnel simulations are conducted with perfectly-smooth walls to further simplify the problem and perform the initial testing of different solver-based RANS models. The Baldwin-Lomax model is observed to be more accurate than the SST model. However, when these RANS models and their roughness augmentation models are utilized to study their accuracy with respect to the experimental datasets, where the roughness effects are activated, both models perform well for a low roughness height case. However, as the roughness height increases, the SST model more accurately predicts the wall data (shear and pressure) than the Baldwin-Lomax model. Therefore, this present work has built a solid foundation for selecting the best RANS model to study the wall data under high-enthalpy flow conditions at the AHF facility soon.

Prakash Shrestha↗
NASA NTRS1982

Curve fitting and modeling with splines using statistical variable selection techniques

The successful application of statistical variable selection techniques to fit splines is demonstrated. Major emphasis is given to knot selection, but order determination is also discussed. Two FORTRAN backward elimination programs, using the B-spline basis, were developed. The program for knot elimination is compared in detail with two other spline-fitting methods and several statistical software packages. An example is also given for the two-variable case using a tensor product basis, with a theoretical discussion of the difficulties of their use.

Smith, P. L.↗
NASA NTRS1991

Minimum-fuel rescue trajectories for the Extravehicular Excursion Unit

The problem of determining minimum-fuel trajectories for rescuing astronauts or equipment which become separated from a Space Station is addressed. Using the Clohessy-Wiltshire equations of relative motion and assuming impulsive Delta-Vs, the minimum-fuel rescue problem is shown to be a parameter optimization problem. Minimum-fuel rescue trajectories are found for seventeen test cases using a recursive quadratic programming algorithm. The results are analyzed and general rules for astronaut rescue and equipment retrieval are developed.

Fowler, W. T.↗
NASA NTRS1990

Design sensitivity derivatives for isoparametric elements by analytical and semi-analytical approaches

This paper presents an analytical approach for incorporating design sensitivity calculations directly into the finite element analysis. The formulation depends on the implicit differentiation approach and requires few additional calculations to obtain the design sensitivity derivatives. In order to evaluate this approach, it is compared with the semi-analytical approach which is based on commonly used finite difference formulations. Both approaches are implemented to calculate the design sensitivities for continuum and structural isoparametric elements. To demonstrate the accuracy and robustness of the developed analytical approach compared to the semi-analytical approach, some test cases using different structural and continuum element types are presented.

Zumwalt, Kenneth W.↗
NASA NTRS1982

Fitting multidimensional splines using statistical variable selection techniques

This report demonstrates the successful application of statistical variable selection techniques to fit splines. Major emphasis is given to knot selection, but order determination is also discussed. Two FORTRAN backward elimination programs using the B-spline basis were developed, and the one for knot elimination is compared in detail with two other spline-fitting methods and several statistical software packages. An example is also given for the two-variable case using a tensor product basis, with a theoretical discussion of the difficulties of their use.

Smith, P. L.↗