Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Three-Dimensional Heat Flux and Thermal Analysis of Angled Tungsten Samples on DIII-D

ITER-grade tungsten and dispersoid-strengthened tungsten samples with the top surface angled at ~15° towards the incident plasma flux were exposed to 9 H-mode discharges with edge-localized modes (ELMs) in the lower divertor of DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Surface damage included cracking and flaking of material on the two samples farthest away from the plasma strike point, and significant melting of the two samples closest to the strike point. Heat flux and thermal analysis tools new to DIII-D have been applied to better understand this material response and to help optimize the exposure conditions for future experiments. SMITER field-line tracing simulations based on IRTV data and EFIT equilibria estimate an average inter-ELM perpendicular heat flux, 𝑞⊥,𝑖nter−𝐸LM , on the angled surfaces of 10.1 – 19.6 MW/m² for a majority of the 9 discharges, increasing to 15.6 – 24.5 MW/m² for the single, higher-power shot where samples melted. Fast camera data showed shallow intra-ELM melting and re-solidification, which transitioned to bulk inter-ELM melting with melt motion in the 𝐽⃗ 𝑥 𝐵⃗ direction. About 50% of the protruding volume of the most affected sample was displaced via melt-motion. SIERRA thermal modeling software was able to reproduce an onset time of melting consistent with fast camera data and final sample conditions, within < 200 ms. Maximum surface temperatures of 3122 K and 2787 K are estimated for the samples farthest away from the strike point, while the closest samples achieve melting at 4067 ms and 4750 ms into the ~5000 ms plasma exposure. A +10% increase in both the SMITER 𝑞⊥,𝑖nter−𝐸LM calculations and the estimated ELM heat loads 𝑞⊥, 𝐸LM was required to achieve this result, which is within the uncertainty of the diagnostic data but likely accounts for non-ideal geometry effects plus other physics uncertainties not included in this first iteration of modeling. This work provided valuable estimates of the 3D temperature evolution to help better understand the observed surface morphology and internal recrystallization of samples, which are discussed in detail in a complementary manuscript [1]. Benchmarking efforts with more diagnosed DIII-D experiments are underway to further refine the SMITER and SIERRA models for DiMES. Future use of these tools will enable researchers to precisely target heat flux exposure conditions in DIII-D to test, but not exceed, the thermomechanical limitations of novel plasma-facing materials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

State densities of heavy nuclei in the static-path plus random-phase approximation

We report that nuclear state densities are important inputs to statistical models of compound-nucleus reactions. State densities are often calculated with self-consistent mean-field approximations that do not include important correlations and must be augmented with empirical collective enhancement factors. Here, we benchmark the static-path plus random-phase approximation (SPA + RPA) to the state density in a chain of samarium isotopes 148–155 Sm against exact results (up to statistical errors) obtained with the shell-model Monte Carlo (SMMC) method. The SPA + RPA method incorporates all static fluctuations beyond the mean field together with small-amplitude quantal fluctuations around each static fluctuation. Using a pairing plus quadrupole interaction, we show that the SPA + RPA state densities agree well with the exact SMMC densities for both the even- and odd-mass isotopes. For the even-mass isotopes, we also compare our results with mean-field state densities calculated with the finite-temperature Hartree-Fock-Bogoliubov (HFB) approximation. We find that the SPA + RPA repairs the deficiencies of the mean-field approximation associated with broken rotational symmetry in deformed nuclei and with the violation of particle-number conservation in the pairing condensate. In particular, in deformed nuclei the SPA + RPA reproduces the rotational enhancement of the state density relative to the mean-field state density.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

K ∗ (892) ± resonance production in Pb−Pb collisions at $\sqrt{s_{NN}}$ = 5.02 TeV

The production of K *⁢(892) ± meson resonance is measured at midrapidity (| y |<0.5) in Pb-Pb collisions at $\sqrt{^sNN}$ = 5.02 TeV using the ALICE detector at the CERN Large Hadron Collider. The resonance is reconstructed via its hadronic decay channel K *⁢(892) ± → K $^0_S$⁢π ± . The transverse momentum distributions are obtained for various centrality intervals in the p T range of 0.4-16 GeV/ c . Measurements of integrated yields, mean transverse momenta, and particle yield ratios are reported and found to be consistent with previous ALICE measurements for K *⁢(892) 0 within uncertainties. The p T -integrated yield ratio 2 K *⁢(892) ± ⁢/(⁢ K + + K - ) in central Pb-Pb collisions shows a significant suppression at a level of 9.3σ⁢ relative to pp collisions. Thermal model calculations result in an overprediction of the particle yield ratio. Although both hadron resonance gas in partial chemical equilibrium (HRG-PCE) and MUSIC + SMASH simulations consider the hadronic phase, only HRG-PCE accurately represents the measurements, whereas MUSIC + SMASH simulations tend to overpredict the particle yield ratio. These observations, along with the kinetic freeze-out temperatures extracted from the yields measured for light-flavored hadrons using the HRG-PCE model, indicate a finite hadronic phase lifetime, which decreases with increasing collision centrality percentile. The p T-differential yield ratios 2 K *⁢(892) ±⁢ /(⁢ K + + K - ) and 2 K *⁢(892) ± ⁢/(⁢π + +π - ) are presented and compared with measurements in pp collisions at $\sqrt{s}$ = 5.02 TeV. Both particle ratios are found to be suppressed by up to a factor of five at p T <2.0 GeV/ c in central Pb-Pb collisions and are qualitatively consistent with expectations for rescattering effects in the hadronic phase. The nuclear modification factor ( R AA ) shows a smooth evolution with centrality and is found to be below unity at p T >8 GeV/ c , consistent with measurements for other light-flavored hadrons. The smallest values are observed in most central collisions, indicating larger energy loss of partons traversing the dense medium.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Measurements of H Λ 3 and H Λ 4 Lifetimes and Yields in Au + Au Collisions in the High Baryon Density Region

We report precision measurements of hypernuclei $^3_ΛH$ and $^4_ΛH$ lifetimes obtained from Au + Au collisions at $\sqrt{sNN}$ = 3.0 GeV and 7.2 GeV collected by the STAR experiment at the Relativistic Heavy Ion Collider, and the first measurement of $^3_ΛH$ and $^4_ΛH$ midrapidity yields in Au + Au collisions at $\sqrt{sNN}$ = 3.0 GeV. $^3_ΛH$ and $^4_ΛH$, being the two simplest bound states composed of hyperons and nucleons, are cornerstones in the field of hypernuclear physics. Their lifetimes are measured to be 221 ± 15 (stat) ± 19 (syst) ps for $^3_ΛH$ and 218 ± 6 (stat) ± 13 (syst) ps for $^4_ΛH$. The p T -integrated yields of $^3_ΛH$ and $^4_ΛH$ are presented in different centrality and rapidity intervals. It is observed that the shape of the rapidity distribution of $4_ΛH$ is different for 0%–10% and 10%–50% centrality collisions. Thermal model calculations, using the canonical ensemble for strangeness, describes the $^3_ΛH$ yield well, while underestimating the $^4_ΛH$ yield. Transport models, combining baryonic mean-field and coalescence (jam) or utilizing dynamical cluster formation via baryonic interactions (phqmd) for light nuclei and hypernuclei production, approximately describe the measured $^3_ΛH$ and $^4_ΛH$ yields. Our measurements provide means to precisely assess our understanding of the fundamental baryonic interactions with strange quarks, which can impact our understanding of more complicated systems involving hyperons, such as the interior of neutron stars or exotic hypernuclei.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Beam Energy Dependence of Triton Production and Yield Ratio $N_t \times N_p / N^2_d$ in Au+Au Collisions at RHIC

We report the triton (t) production in midrapidity (|y| < 0.5) Au + Au collisions at $\sqrt{s_{NN}} = 7.7-200$ GeV measured by the STAR experiment from the first phase of the beam energy scan at the Relativistic Heavy Ion Collider. The nuclear compound yield ratio ($N_t \times N_p / N^2_d$), which is predicted to be sensitive to the fluctuation of local neutron density, is observed to decrease monotonically with increasing charged-particle multiplicity ($dN_{ch}/dη$) and follows a scaling behavior. The $dN_{ch}/dη$ dependence of the yield ratio is compared to calculations from coalescence and thermal models. Enhancements in the yield ratios relative to the coalescence baseline are observed in the 0%-10% most central collisions at 19.6 and 27 GeV, with a significance of 2.3σ and 3.4σ, respectively, giving a combined significance of 4.1σ. The enhancements are not observed in peripheral collisions or model calculations without critical fluctuation, and decreases with a smaller $p_T$ acceptance. The physics implications of these results on the QCD phase structure and the production mechanism of light nuclei in heavy-ion collisions are discussed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Observation of the Ω⁡(2012) baryon at the LHC

A signal consistent with the Ω⁡(2012) baryon has been observed with a significance of 15⁢𝜎 in pp collisions at $\sqrt{𝑠}$ = 13 TeV at the LHC. In this paper, the analysis technique is described and measurements of the mass and width of the Ω⁡(2012) are reported, along with the first measurement of its transverse-momentum spectrum and yield. This paper corroborates the observation by the Belle Collaboration of this excited Ω state and the observation that the Ω⁡(2012) has a rather narrow width for a strongly decaying resonance. The yield measurement is combined with a statistical thermal model calculation of strange baryon yield ratios to obtain estimates of the Ω⁢(2012) − → $Ξ⁢\bar{\textrm{K}}$ branching ratios. These results will improve our understanding of the internal structure and mass spectrum of excited baryon states and serve as a baseline for searches regarding modifications of these properties in high-temperature media.

Acharya, S. [INFN] (ORCID:0000000292135329)↗
DOE OSTI2025

On the Quantum Mechanics of Entropic Forces

It was conjectured 30 years ago that gravity could arise from the entropic rearrangement of information. We offer a set of microscopic quantum models which realize this idea in detail. In particular, we suggest a simple mechanism by which Newton’s law of gravity arises from extremization of the free energy of a collection of qubits or oscillators, rather than from the exchange of virtual quanta of a fundamental field. We give both a local and a nonlocal version of the construction and show how to distinguish a range of these entropic models from ordinary perturbative quantum gravity using existing observations and near-term experiments.

quantum fluctuations↗
DOE OSTI2022

3D Frequency Domain Reflectometry Digital Twin of an Electrical Cable: A First Glance

Electrical cables within nuclear power plants (NPPs) are critical components required for power, control, and instrumentation systems which may be exposed to stressors, such as elevated temperatures and gamma radiation. Such stressors can lead to a reduction in the remaining useful life of electrical cables, jeopardizing the safety of NPP systems. To evaluate the effect of stressors on the degradation of electrical cables, electrical reflectometry methods are commonly employed. Frequency domain reflectometry (FDR) is a non-destructive electrical reflectometry method that uses transmission line theory to detect degradation or impedance changes within electrical cables. However, in most cases FDR is only applied to de-energized cables, limiting the application in NPPs as the cable system must be taken offline. In this work, we explore the development of an FDR digital twin to predict the degradation of an electrical cable exposed to elevated temperature, which is expected to reduce the need for offline FDR. A 3-conductor low-voltage electrical cable was selected for evaluation of the digital twin. The fully three-dimensional digital twin was developed in COMSOL using the RF module. A cable length of 30-m and frequency bandwidth of 400 MHz was selected to mimic real-world application of FDR. Over a 1-m region, the permittivity of the insulation was varied by up to 20% to model thermal degradation. The results demonstrate accurate detection of the insulation damage region, supporting further investigation of the FDR digital twin using real-world data and machine learning for predictive damage estimation or remaining lifetime.

Spencer, Mychal P.↗
DOE OSTI2020

Characterization and Analysis of Insulated Metal Substrate-Based SiC Power Module for Traction Application

This paper presents the electrical characterization and drive cycle--based thermal analysis of an insulated metal substrate (IMS)--based silicon carbide power module for high-power traction inverters. The substrate was constructed using a thin layer of polymer--ceramic blend dielectric material with a thick copper core to improve transient thermal performance. The cooling performance of this module has already been validated with promising results. In this paper, an experimental test bed was set up to evaluate the dynamic and static electrical performance of the designed module under a wide range of operating conditions. The characterization results were then used to develop a drive cycle--based thermal model to validate the performance compared to the traditional direct bonded copper--based power module. The results indicate that the IMS-based power module is a suitable solution for high-power traction applications.

Chowdhury, Shajjad↗
DOE OSTI2021

Optimal Energy Scheduling and Sensitivity Analysis for Integrated Power-Water-Heat Systems

The conventionally independent power, water, and heating networks are becoming more tightly connected, which motivates their joint optimal energy scheduling to improve the overall efficiency of an integrated energy system. However, such a joint optimization is known as a challenging problem with complex network constraints and couplings of electric, hydraulic, and thermal models that are nonlinear and nonconvex. We formulate an optimal power-water-heat flow (OPWHF) problem and develop a computationally efficient heuristic to solve it. The proposed heuristic decomposes OPWHF into subproblems, which are iteratively solved via convex relaxation and convex-concave procedure. Simulation results validate that the proposed framework can improve operational flexibility and social welfare of the integrated system, wherein the water and heating networks respond as virtual energy storage to time-varying energy prices and solar photovoltaic generation. Moreover, we perform sensitivity analysis to compare two modes of heating network control: by flow rate and by temperature. Our results reveal that the latter is more effective for heating networks with a wider space of pipeline parameters.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Development of a 250 Degree C 15kV Supercascode Switch Using SiC JFET Technology

Tetra Corporation is developing a pulsed power drilling system for the geothermal industry. The system requires a high temperature switching technology to replace the existing technology based on Si thyristors with a temperature limit of 150 degrees C. This work focuses on the development of such switch based on a Supercascode configuration using SiC JFET technology. The development presented contains thermal models, packaging design and processes, circuit simulations and prototypes of both the Supercascode switch and the high temperature packaged SiC JFETs.

cascaded switch↗
DOE OSTI2020

Light-nuclei production and search for the QCD critical point

We discuss the potential of light-nuclei measurements in heavy-ion collisions at intermediate energies for the search of the hypothetical QCD critical end-point. A previous proposal based on neutron density fluctuations has brought appealing experimental evidences of a maximum in the ratio of the number of tritons times protons, divided over deuterons square, $\mathcal{O}_{tpd}$. However these results are difficult to reconcile with the state-of-the-art statistical thermal model predictions. Based on the idea that the QCD critical point can lead to a substantial attraction among nucleons, we propose new light-nuclei multiplicity ratios involving 4 He in which the maximum would be more noticeable. We argue that the experimental extraction is feasible by presenting these ratios formed from actual measurements of total and differential yields at low and high collision energies from FOPI and ALICE experiments, respectively. We also illustrate the possible behavior of these ratios at intermediate energies applying a semiclassical method based on flucton paths using the preliminary NA49 and STAR data for $\mathcal{O}_{tpd}$ as input.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Production of pions, kaons, (anti-)protons and &straightphi; mesons in Xe–Xe collisions at $\sqrt{s_{NN}}$ = 5.44 TeV

The first measurement of the production of pions, kaons, (anti-)protons and &straightphi; mesons at midrapidity in Xe–Xe collisions at $\sqrt{s_{NN}}$ = 5.44 TeV is presented. Transverse momentum (p T ) spectra and p T -integrated yields are extracted in several centrality intervals bridging from p–Pb to mid-central Pb–Pb collisions in terms of final-state multiplicity. The study of Xe–Xe and Pb–Pb collisions allows systems at similar charged-particle multiplicities but with different initial geometrical eccentricities to be investigated. A detailed comparison of the spectral shapes in the two systems reveals an opposite behaviour for radial and elliptic flow. In particular, this study shows that the radial flow does not depend on the colliding system when compared at similar charged-particle multiplicity. In terms of hadron chemistry, the previously observed smooth evolution of particle ratios with multiplicity from small to large collision systems is also found to hold in Xe–Xe. In addition, our results confirm that two remarkable features of particle production at LHC energies are also valid in the collision of medium-sized nuclei: the lower proton-to-pion ratio with respect to the thermal model expectations and the increase of the &straightphi;-to-pion ratio with increasing final-state multiplicity.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

SNF Interim Storage Canister Corrosion and Surface Environment Investigations (FY2020 Status Report)

This progress report describes work performed during FY20 at Sandia National Laboratories (SNL) to assess the localized corrosion performance of container/cask materials used in the interim storage of spent nuclear fuel (SNF). Of particular concern is stress corrosion cracking (SCC), by which a through-wall crack could potentially form in a canister outer wall over time intervals that are shorter than possible dry storage times. Work in FY20 further defined our understanding of the potential chemical and physical environment present on canister surfaces, evaluated the relationship between the environment and the resultant corrosion that occurs, and initiated crack growth rate testing under relevant environmental conditions. In FY20, work to define dry storage canister surface environments included several tasks. First, collection of dust deposition specimens from independent spent fuel storage installation (ISFSI) site locations helped to establish a more complete understanding of the potential chemical environment formed on the canister. Second, the predicted evolution of canister surface relative humidity RH) values was estimated using ISFSI site weather data and the horizontal canister thermal model used by the SNL probabilistic SCC model. These calculations determined that for typical ISFSI weather conditions, seasalt deliquescence to produce MgCl2-rich brines could occur in less than 20 years at the coolest locations on the canister surface, and, even after nearly 300 years, conditions for NaCl deliquescence (75% RH) are not reached. This work illustrates the importance of understanding the stability of MgCl2-rich brines on the heated canister surface, and the potential impact of brine composition on corrosion processes, including pitting and stress corrosion cracking. In an additional study, the description of the canister surface environment was refined in order to define more realistic corrosion testing environments including diurnal cycles, soluble salt chemistries, and inert mineral particles. The potential impacts of these phenomena on canister corrosion are being evaluated experimentally. Finally, work over the past few years to evaluate the stability of magnesium chloride brines continued in FY20. MgCl2 degassing experiments were carried out, confirming that MgCl2 brines slowly degas HCl on heated surfaces, converting to less deliquescent magnesium hydroxychloride phases and potentially leading to brine dryout.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Low Temperature Time-to-Explosion Experiments on HMX in the LLNL's ODTX/P-ODTX System (FY 2020 Annual Report)

Over the last few decades, there has been a considerable research effort on the thermal decomposition and thermal explosion violence of energetic materials at elevated temperatures in different sample geometries and confinements. Thermal explosion studies on various energetic materials in two-dimensional geometry such as the Scaled-Thermal-Explosion-Experiment (STEX) system and the Sandia-Instrumented-Thermal-Ignition (SITI) system have been reported. The One-Dimensional Time to Explosion (ODTX) system, designed and built by LLNL, has been used since 1970s for thermal explosion studies. The system is attractive because of the one-dimensional geometry and minimal sample requirement. With the recent integration of a pressure monitoring element, the system can study pressure behavior of materials subjected to and during thermal exposure. Rapid pressure monitoring in µsec intervals allow for enhanced pressure determination in the time right before thermal explosion. The test data can be used for the validation of existing thermal models, particularly for introducing pressure terms. This report summarizes the efforts in performing small-scale safety tests, particle size measurements and conducting 7 ODTX/P-ODTX experiments on the Cl5 HMX material that Hunting uses for oil field applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Sound Speed as a Candidate for Internal Temperature Monitoring During Solid Phase Processing of Materials

Internal temperature is an important parameter for understanding the solid phase processing (SPP) of materials and improving feedback control of these processes. Friction stir processes, shear assisted processing and extrusion (ShAPE ™ ), and ultrahigh velocity (UHV) cold spray are examples of such processes. Simple thermal models based on temperatures measured at the boundary of the deforming body cannot capture the dynamic nature of temperature generation within the deforming solid. One possibly way of understanding internal temperature is by measuring sound speed, which varies as a function of temperature for materials and directing ultrasonic wave propagation through selected material volumes of interest. In this project, longitudinal wave speed is estimated for aluminum 6061. Piezoelectric materials bonded to a specimen provided data from which longitudinal wave speed was estimated. A discussion evaluated the linear relationship of wave speed versus temperature and postulated how wave speed measurements could be used to estimate the internal temperature of selected material volumes for feedback during SPP of materials. Instrumentation, data and analysis, and a discussion are reviewed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

An asymptotic approach for the statistical thermodynamics of certain model systems

In classical statistical thermodynamics, calculating the configuration integral is both vital and elusive. Analytic relations for configuration integrals are desirable for modeling purposes, but it is typically impossible to obtain them. Certain systems become analytically tractable after replacing steep potential energies with harmonic potentials or athermal rigid constraints, but these approximations are often inadequate, especially when modeling the stretching of molecules. It is therefore necessary to develop a systematic approach to improve upon the approximations provided by these reference systems. Here, a general asymptotic approach is introduced, where the configuration integral for the full system is obtained in terms of that of the reference system and several corrections. This asymptotic approach is first demonstrated using the simple example of a classical three-dimensional oscillator. Next, the approach is applied to modeling the stretching of single polymer chains and to modeling thermally assisted crack growth, where results are verified with respect to numerical calculations. Overall, this asymptotic approach is a valid and effective tool for statistical thermodynamics in general.

Buche, Michael Robert↗