Results for “test configuration” — Page 20

NASA NTRS2005

A Computational Study of a New Dual Throat Fluidic Thrust Vectoring Nozzle Concept

A computational investigation of a two-dimensional nozzle was completed to assess the use of fluidic injection to manipulate flow separation and cause thrust vectoring of the primary jet thrust. The nozzle was designed with a recessed cavity to enhance the throat shifting method of fluidic thrust vectoring. Several design cycles with the structured-grid, computational fluid dynamics code PAB3D and with experiments in the NASA Langley Research Center Jet Exit Test Facility have been completed to guide the nozzle design and analyze performance. This paper presents computational results on potential design improvements for best experimental configuration tested to date. Nozzle design variables included cavity divergence angle, cavity convergence angle and upstream throat height. Pulsed fluidic injection was also investigated for its ability to decrease mass flow requirements. Internal nozzle performance (wind-off conditions) and thrust vector angles were computed for several configurations over a range of nozzle pressure ratios from 2 to 7, with the fluidic injection flow rate equal to 3 percent of the primary flow rate. Computational results indicate that increasing cavity divergence angle beyond 10 is detrimental to thrust vectoring efficiency, while increasing cavity convergence angle from 20 to 30 improves thrust vectoring efficiency at nozzle pressure ratios greater than 2, albeit at the expense of discharge coefficient. Pulsed injection was no more efficient than steady injection for the Dual Throat Nozzle concept.

Deere, Karen A.↗

NASA NTRS1981

Model aerodynamic test results for two variable cycle engine coannular exhaust systems at simulated takeoff and cruise conditions. Comprehensive data report. Volume 2: Tabulated aeroynamic data book 1

Tabulated data from wind tunnel tests conducted to evaluate the aerodynamic performance of an advanced coannular exhaust nozzle for a future supersonic propulsion system are presented. Tests were conducted with two test configurations: (1) a short flap mechanism for fan stream control with an isentropic contoured flow splitter, and (2) an iris fan nozzle with a conical flow splitter. Both designs feature a translating primary plug and an auxiliary inlet ejector. Tests were conducted at takeoff and simulated cruise conditions. Data were acquired at Mach numbers of 0, 0.36, 0.9, and 2.0 for a wide range of nozzle operating conditions. At simulated supersonic cruise, both configurations demonstrated good performance, comparable to levels assumed in earlier advanced supersonic propulsion studies. However, at subsonic cruise, both configurations exhibited performance that was 6 to 7.5 percent less than the study assumptions. At takeoff conditions, the iris configuration performance approached the assumed levels, while the short flap design was 4 to 6 percent less. Data are provided through test run 25.

Nelson, D. P.↗

NASA NTRS1971

Aerodynamic characteristics of the MSFC pressure fed boosters at high angles of attack (M equals 0.6 to 5.0)

Experimental aerodynamic investigations were conducted in the 14 x 14 inch trisonic wind tunnel during early December 1971 on 0.003366 scale models of the space shuttle pressure fed booster configurations. The basic configurations tested were a 40 deg cone/cylinder/13 deg flare designated the pressure fed booster and a 35 deg cone/cylinder designated the pressure fed booster configuration x. Six component aerodynamic force and moment data were recorded over a Mach number range from 0.6 to 5.0 at angles of attack from +20 to +60 deg at 0 deg sideslip and over a sideslip range from -10 to +10 deg at 31 and 52 deg angles of attack. Primary configuration variables for the two basic pressure fed booster configurations were fin size and fin dihedral position.

Baker, J.↗

NASA NTRS1987

Wind-tunnel free-flight investigation of a 0.15-scale model of the F-106B airplane with vortex flaps

An investigation to determine the effects of vortex flaps on the flight dynamic characteristics of the F-106B in the area of low-speed, high-angle-of-attack flight was undertaken on a 0.15-scale model of the airplane in the Langley 30- by 60-Foot Tunnel. Static force tests, dynamic forced-oscillation tests, as well as free-flight tests were conducted to obtain a data base on the flight characteristics of the F-106B airplane with vortex flaps. Vortex flap configurations tested included a full-span gothic flap, a full-span constant-chord flap, and a part-span gothic flap.

Yip, Long P.↗

NASA NTRS2006

Noise Radiation from Single and Multiple Rod Configurations

Acoustic measurements were performed on single and multiple rod configurations to study the effect of Reynolds number, surface roughness, freestream turbulence, proximity and wake interference on the radiated noise. The Reynolds number ranged from 3.8 x 10(exp 3) to 10(exp 5). Directivity measurements were performed to determine how well the dipole assumption for the radiation of vortex shedding noise holds for the different model configurations tested. The dependence of the peak Sound Pressure Level on velocity was also examined. Several concepts for the reduction of the noise radiating from cylindrical rods were tested. It was shown that wire wraps and collar distributions could be used to significantly reduce the noise radiating from rods in tandem configurations.

Hutcheson, Florence V.↗

NASA NTRS2017

Electrically Heated Testing of the Kilowatt Reactor Using Stirling Technology (KRUSTY) Experiment Using a Depleted Uranium Core

The Kilopower project aims to develop and demonstrate scalable fission-based power technology for systems capable of delivering 110 kW of electric power with a specific power ranging from 2.5 - 6.5 Wkg. This technology could enable high power science missions or could be used to provide surface power for manned missions to the Moon or Mars. NASA has partnered with the Department of Energys National Nuclear Security Administration, Los Alamos National Labs, and Y-12 National Security Complex to develop and test a prototypic reactor and power system using existing facilities and infrastructure. This technology demonstration, referred to as the Kilowatt Reactor Using Stirling TechnologY (KRUSTY), will undergo nuclear ground testing in the summer of 2017 at the Nevada Test Site. The 1 kWe variation of the Kilopower system was chosen for the KRUSTY demonstration. The concept for the 1 kWe flight system consist of a 4 kWt highly enriched Uranium-Molybdenum reactor operating at 800 degrees Celsius coupled to sodium heat pipes. The heat pipes deliver heat to the hot ends of eight 125 W Stirling convertors producing a net electrical output of 1 kW. Waste heat is rejected using titanium-water heat pipes coupled to carbon composite radiator panels. The KRUSTY test, based on this design, uses a prototypic highly enriched uranium-molybdenum core coupled to prototypic sodium heat pipes. The heat pipes transfer heat to two Advanced Stirling Convertors (ASC-E2s) and six thermal simulators, which simulate the thermal draw of full scale power conversion units. Thermal simulators and Stirling engines are gas cooled. The most recent project milestone was the completion of non-nuclear system level testing using an electrically heated depleted uranium (non-fissioning) reactor core simulator. System level testing at the Glenn Research Center (GRC) has validated performance predictions and has demonstrated system level operation and control in a test configuration that replicates the one to be used at the Device Assembly Facility (DAF) at the Nevada National Security Site. Fabrication, assembly, and testing of the depleted uranium core has allowed for higher fidelity system level testing at GRC, and has validated the fabrication methods to be used on the highly enriched uranium core that will supply heat for the DAF KRUSTY demonstration.

Briggs, Maxwell H.↗

NASA NTRSDate not supplied

Updating High-Order Aeroservoelastic Models from Low-Order System Identification Results

Estimating aircraft models from test data requires several simplifying assumptions that introduce biases into the parameter estimates. In this paper, these biases are defined and a method for estimating the biases is discussed. Having an estimate of the bias allows the parameters estimated from test to be integrated into a high-order model. The Integrated Adaptive Wing Technology Maturation (IAWTM) wind tunnel model is discussed and the bias is demonstrated for one of the testing configurations. The methodology was able to estimate these biases and apply corrections to high-order aeroelastic models to improve the fit to test data. The consideration of the biases allows more meaningful comparisons and avoids the erroneous differences between pretest predictions and the fitted model.

Jeffrey Ouellette↗

NASA NTRSDate not supplied

Updating High-Order Aeroservoelastic Models from Low-Order System Identification Results

Estimating aircraft models from test data requires several simplifying assumptions that introduce biases into the parameter estimates. In this paper, these biases are defined and a method for estimating the biases is discussed. Having an estimate of the bias allows the parameters estimated from test to be integrated into a high-order model. The Integrated Adaptive Wing Technology Maturation (IAWTM) wind tunnel model is discussed and the bias is demonstrated for one of the testing configurations. The methodology was able to estimate these biases and apply corrections to high-order aeroelastic models to improve the fit to test data. The consideration of the biases allows more meaningful comparisons and avoids the erroneous differences between pretest predictions and the fitted model.

Jeffrey Ouellette↗

NASA NTRS1975

Unsteady loads due to propulsive lift configurations

The flow of a jet over an airfoil representative of upper surface blowing was studied using laser techniques. Experimental techniques were developed for the investigation of unsteady pressures behind a cold model jet. Construction of a 1/4 scale model of the 'Beach' test configuration was completed along with construction of a portable detector. The portable detector is used in conjunction with a laser to measure jet flows during tests on the 'Beach' facility. The detector incorporates both optical and electronic components.

Morton, J. B.↗

NASA NTRS1989

The effect of solidity on propeller normal force

Propeller normal force is a major contributor to pitch and yaw stability on propeller driven aircraft. While it is well known that propeller normal force is a function of the number of blades, there are no published data for the high numbers of blades that are used in the new designs such as the UDF. This paper presents the results of a test conducted in the NASA Langley 14- x 22-foot Subsonic Tunnel using a sting-mounted counter-rotation propeller and nacelle. The configurations tested were combinations of 0, 4, and 8 blades per hub. Tests were conducted for blade angle settings of 31.34, 36.34, and 41.34 deg over an angle-of-attack range from -10 to 90 deg and over a range of advance ratios from 0.8 to 1.4. The results show that propeller normal force varies with both solidity and angle of attack.

Dunham, Dana Morris↗

NASA NTRS2007

Computational Analyses of Offset Stream Nozzles for Noise Reduction

The Wind computational fluid dynamics code was used to perform a series of simulations on two offset stream nozzle concepts for jet noise reduction. The first concept used an S-duct to direct the secondary stream to the lower side of the nozzle. The second concept used vanes to turn the secondary flow downward. The analyses were completed in preparation of tests conducted in the NASA Glenn Research Center Aeroacoustic Propulsion Laboratory. The offset stream nozzles demonstrated good performance and reduced the amount of turbulence on the lower side of the jet plume. The computer analyses proved instrumental in guiding the development of the final test configurations and giving insight into the flow mechanics of offset stream nozzles. The computational predictions were compared with flowfield results from the jet rig testing and showed excellent agreement.

Dippold, Vance, III↗

NASA NTRS2018

Two-Speed Rotorcraft Research Transmission Power-Loss Associated with the Lubrication and Hydraulic Rotating Feed-Through Design Feature

An investigation was completed into the power loss associated with a rotating feed-through (RFT) design feature used to transfer lubrication and a hydraulic control signal from the static reference frame to a rotating reference frame in the NASA GRC two-speed transmission tests conducted in the Variable-Speed Drive Test Rig. The RFT feature, not commercially available, was created specifically for this research project and is integral to all two-speed transmission configurations tested, as well as a variant concept design for a geared variable-speed transmission presented at AHS Forum 71 in 2015. The experimental set-up and results from measurements in the isolated rotating-feed-through (RFT) experiments are presented. Results were used in an overall power loss assessment for a scaled conceptual 1,000 horsepower inline concentric two-speed transmission to support a NASA Revolutionary Vertical Lift Technologies (RVLT) Technical Challenge, demonstrating 50% speed change with less than 2% power loss while maintaining current power-to-weight ratios.

Rotorcraft↗

NASA NTRS2018

Two-Speed Rotorcraft Research Transmission Power-Loss Associated with the Lubrication and Hydraulic Rotating Feed-Through Design Feature

An investigation was completed into the power loss associated with a rotating feed-through (RFT) design feature used to transfer lubrication and a hydraulic control signal from the static reference frame to a rotating reference frame in the NASA GRC two-speed transmission tests conducted in the Variable-Speed Drive Test Rig. The RFT feature, not commercially available, was created specifically for this research project and is integral to all two-speed transmission configurations tested, as well as a variant concept design for a geared variable-speed transmission presented at AHS Forum 71 in 2015. The experimental set-up and results from measurements in the isolated rotating-feed-through (RFT) experiments are presented. Results were used in an overall power loss assessment for a scaled conceptual 1,000 horsepower inline concentric two-speed transmission to support a NASA Revolutionary Vertical Lift Technologies (RVLT) Technical Challenge, demonstrating 50% speed change with less than 2% power loss while maintaining current power-to-weight ratios.

Rotorcraft↗

NASA NTRS2018

Two-Speed Rotorcraft Research Transmission Power-Loss Associated with the Lubrication and Hydraulic Rotating Feed-Through Design Feature

An investigation was completed into the power loss associated with a rotating feed-through (RFT) design feature used to transfer lubrication and a hydraulic control signal from the static reference frame to a rotating reference frame in the NASA GRC two-speed transmission tests conducted in the Variable-Speed Drive Test Rig. The RFT feature, not commercially available, was created specifically for this research project and is integral to all two-speed transmission configurations tested, as well as a variant concept design for a geared variable-speed transmission presented at AHS Forum 71 in 2015. The experimental set-up and results from measurements in the isolated rotating-feed-through (RFT) experiments are presented. Results were used in an overall power loss assessment for a scaled conceptual 1,000 horsepower inline concentric two-speed transmission to support a NASA Revolutionary Vertical Lift Technologies (RVLT) Technical Challenge, demonstrating 50% speed change with less than 2% power loss while maintaining current power-to-weight ratios.

Rotorcraft↗

DOE OSTI2021

Prediction of Aluminum to Steel RSW Joint Failure (CRADA 405)

General Motors, LLC has developed a resistance spot welding process to join aluminum sheet to steel for body-in-white manufacturing. Efforts to develop the process for any one joint configuration (combination of alloy and thicknesses) is intensive. To aid in process understanding and eventual reduction in process development efforts, an initiative was created to develop an finite element model of the various destructive test configurations (lap shear, cross-tension, and coach peel) to help predict the failure mode and load displacement curves under tensile testing. This report describes the finite element modeling approach, the means by which local material properties were determined, as well as model validation and refinement efforts.

36 MATERIALS SCIENCE↗

NASA NTRS2003

Design and test of a 2m x 4m DART system

A 2 meter by 4 meter DART (dual anamorphic reflector telescope) system has been designed and fabricated using thin stretched mesh reflectors. This report documents the structural configuration, test preparation, test results, and analysis correlation.

TPF Terrestrial Planet Finder life detection extra↗

NASA NTRS1972

Wind tunnel investigation of aerodynamic characteristics of scale models of three rectangular shaped cargo containers

Wind tunnel tests were conducted on scale models of three rectangular shaped cargo containers to determine the aerodynamic characteristics of these typical externally-suspended helicopter cargo configurations. Tests were made over a large range of pitch and yaw attitudes at a nominal Reynolds number per unit length of 1.8 x one million. The aerodynamic data obtained from the tests are presented.

Laub, G. H.↗

NASA NTRS1984

Effect of Impact Damage and Open Holes on the Compression Strength of Tough Resin/high Strain Fiber Laminates

Tests to assess the performance of composite structures damaged by impact or containing local discontinuities such as cutouts are discussed. In particular, two plate specimen test configurations which were developed to define the serverity of compression strength reduction are described; one for impact damage and the other open hole specimens. The test technique for impact specimens involves damaging the plate at selected energies, measuring the size of damage by ultrasonic C-scan techniques and measuring the residual strength in a compression load test. Open-hole specimen compression tests are conducted for several different hole diameters and the failure strain and load and mode of failure recorded. The plate specimen used in these tests is designed with length, width, thickness and laminate stiffness to ensure that overall plate buckling is not responsible for initiating failure.

Williams, J. G.↗