SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Etchant containing chloroplatinous or chloroplatinic acid greatly reduces contact resistance between metallic surfaces. Etching results in a monolayer plating of platinum on the wafer surface, preventing oxide growth.
Impurities and interface states in silicon surface and oxide systems
Quasi-equilibrium treatment of heterogeneous reactions applied to flash desorption data for oxygen reaction with tungsten surface, discussing species desorption dependence on adsorption temperature
The characteristics of thin, pyrolytically deposited films for protection of surfaces from oxidation and abrasion are discussed. The limitations of depositing erosion resistant films are described. Environmental tests of first stage compressor blades in a T-58 engine after coating with a thin film were conducted. Photographic examples of the effectiveness of the thin films in protecting the turbine blades are provided. Methods for operating a sputtering system and the equipment used for film deposition are defined.
An experimental and theoretical investigation of the feasibility of using the MOS C-V (capacitance-voltage) technique to determine impurity and surface state concentrations on the diffused face of Si solar cells with Ta2O5 coatings. Impurity concentration 10 A from the diffused surface is found to be 2.9 times 10 to the 20th power per cu cm. Charge density in surface and oxide states is 2.1 times 10 to the 13th power per sq cm. These data agree with theoretical predictions.-
The operation of a turbine in the effluent of a pressurized fluidized bed (PFB) coal combustor presents serious materials problems. Synergistic erosion/corrosion and deposition/corrosion interactions may favor the growth of erosion-resistant oxides on blade surfaces, but brittle cracking of these oxides may be an important source of damage along heavy particle paths. Integrally cast alloy 713LC and IN792 + Hf superalloy turbine rotors in a single-stage turbine with 6% partial admittance have been operated in the effluent of a PFB coal combustor for up to 164 hr. The rotor erosion pattern exhibits heavy particle separation with severe erosion at the leading edge, pressure side center, and suction side trailing edge at the tip. The erosion distribution pattern gives a spectrum of erosion/oxidation/deposition as a function of blade position. The data suggest that preferential degradation paths may exist even under the targeted lower loadings (less than 20 ppm).
Inelastic electron tunneling spectroscopy is a useful technique for the study of vibrational modes of molecules adsorbed on the surface of oxide layers in a metal-insulator-metal tunnel junction. The technique involves studying the effects of adsorbed molecules on the tunneling spectrum of such junctions. The data give useful information about the structure, bonding, and orientation of adsorbed molecules. One of the major advantages of inelastic electron tunneling spectroscopy is its sensitivity. It is capable of detecting on the order of 10 to the 10th molecules (a fraction of a monolayer) on a 1 sq mm junction. It has been successfully used in studies of catalysis, biology, trace impurity detection, and electronic excitations. Because of its high sensitivity, this technique shows great promise in the area of solid-state electronic chemical sensing.
Photoyields and secondary electron emission (SEE) characteristics were determined under UHV conditions for a group of insulating materials used in spacecraft applications. The SEE studies were carried out with a pulsed primary beam while photoyields were obtained with a chopped photon beam from a Kr resonance source with major emission at 123.6 nm. This provides a photon flux close to that of the Lyman alpha in the space environment. Yields per incident photon are obtained relative to those from a freshly evaporated and air oxidized Al surface. Results are presented for Kapton, FEP Teflon, the borosilicate glass covering of a shuttle tile, and spacesuit outer fabric.
An investigation is conducted of the mechanisms by which nitrilotris methylene phosphonic acid (NTMP) and related compounds are adsorbed onto oxidized aluminum surfaces to inhibit hydration and increase the durability of adhesive bonds formed with inhibitor-treated panels. P - O - Al bonds are identified as the basis of adsorption, and it is found that water initially adsorbed onto the etched aluminum surfaces is displaced by the NTMP. The hydration of the NTMP-treated surfaces occurs in three stages, namely the reverisble physisorption of water, the slow dissolution of NTMP followed by rapid hydration of the freshly exposed Al2O3 to AlOOH and further hydration of the surface to Al(OH)3. Five properties of an ideal inhibitor are identified.
Prediction of electrical and thermal contact resistance for pressed, nominally flat contacts is complicated by the large number of variables which influence contact formation. This is reflected in experimental results as a wide variation in contact resistances, spanning up to six orders of magnitude. A series of experiments were performed to observe the effects of oxidation and surface roughness on contact resistance. Electrical contact resistance and thermal contact conductance from 4 to 290 K on OFHC Cu contacts are reported. Electrical contact resistance was measured with a 4-wire DC technique. Thermal contact conductance was determined by steady-state longitudinal heat flow. Corrections for the bulk contribution ot the overall measured resistance were made, with the remaining resistance due solely to the presence of the contact.
Results of studies utilizing normal and rare oxygen isotopes in the catalytic oxidation of carbon monoxide over a platinum-tin oxide catalyst substrate are presented. Chemisorption of labeled carbon monoxide on the catalyst followed by thermal desorption yielded a carbon dioxide product with an oxygen-18 composition consistent with the formation of a carbonate-like intermediate in the chemisorption process. The efficacy of a method developed for the oxygen-18 labeling of the platinum-tin oxide catalyst surface for use in closed cycle pulsed care isotope carbon dioxide lasers is demonstrated for the equivalent of 10 to the 6th power pulses at 10 pulses per second.
The fracture resistance of a commercial TiB 2 particle/SiC matrix composite was evaluated at temperatures ranging from 20 to 1400 °C. A laser interferometric strain gauge (LISG) was used to continuously monitor the crack mouth opening displacement (CMOD) of the chevron-notched and straight-notched, three-point bend specimens used. Crack growth resistance curves (R-curves) were determined from the load versus displacement curves and displacement calibrations. Fracture toughness, work-of-fracture, and R-curve levels were found to decrease with increasing temperature. Microstructure, fracture surface, and oxidation coat were examined to explain the fracture behavior.
The fracture resistance of a commercial TiB2 particle/SiC matrix composite was evaluated at temperatures ranging from 20 to 1400 C. A laser interferometric strain gauge (LiSG) was used to continuously monitor the crack mouth opening displacement (CMOD) of the chevron-notched and straight-notched, three-point bend specimens used. Crack growth resistance curves (R-curves) were determined from the load versus displacement curves and displacement calibrations. Fracture toughness, work-of-fracture, and R-curve levels were found to decrease with increasing temperature. Microstructure, fracture surface, and oxidation coat were examined to explain the fracture behavior.
The solar Xe elemental abundance is determined here using solar wind measurements from lunar ilmenites which are normalized to Si by spacecraft data. The results are compared with estimated abundances assuming no fractionation. When corrected for solar wind/photospheric fractionation, the Xe-130 abundance given by surface layer oxidation of ilmenite from solid 71501 exposed within the last 200 m.y. is 0.24 +/- 0.09 normalized to Si = 10 exp 6. This is indistinguishable from estimates made assuming no solid/gas fractionation. Results from breccia 79035 ilmenite exposed at least 1 Gyr ago indicate that the solar wind Xe flux may have been significantly higher relative to other noble gases, perhaps due to more efficient Xe ionization. If this is true, fluxes of C and S, which have first ionization potentials similar to Xe, should also be higher in the ancient solar wind from the same time period.
The feasibility of using polycrystalline CVD diamond films as temperature sensors in harsh aerospace environment associated with hypersonic flights was tested using patterned diamond resistors, fabricated on flat or curved oxidized Si surfaces, as temperature sensors at temperatures between 20 and 1000 C. In this temperature range, the measured resistance was found to vary over 3 orders of magnitude and the temperature coefficient of resistance to change from 0.017/K to 0.003/K. After an annealing treatment, the resistance change was reproducible within 1 percent on the entire temperature range for short measuring times.
Feasibility of using very thin CVD coatings to provide both protection against oxidation and surfaces of low catalytic activity for thin metallic heat-shield materials demonstrated. Use of aluminum in compositions increases emittances of coatings and reduces transport of oxygen through coatings to substrates. Coatings light in weight and applied to foil-gauge materials with minimum weight penalties.
Subglacial volcanic activity on Iceland has led to the formation of a variety of silicate and iron oxide-rich alteration products that may serve as a model for chemical alteration on Mars. Multiple palagonitic tuffs, altered pillow lavas, hydrothermal springs and alteration at glacial run-off streams were observed during a recent field trip in Iceland. Formation of alteration products and ferrihydrite in similar environments on Mars may have contributed to the ferric oxide-rich surface material there. The spectral and chemical properties of Icelandic alteration products and ferrihydrites are presented here.
Ferrihydrite samples were collected from a thermal spring and a cold stream in the Landmannalaugar region of Iceland. Chemical and spectroscopic analyses have been performed on the air-dried and fine-grained fractions of these samples. The ferrihydrite from the cold stream is a pure sample, containing small amounts of Ca, P and Si, which do not form minerals detectable with X-ray diffraction (XRD) or reflectance and transmittance spectroscopy. The ferrihydrite from the thermal pool is a less pure sample, containing larger amounts of amorphous Si and P. The XRD and spectral features for this sample are also consistent with a less crystalline structure. Some of the Si is incorporated in the structure of the ferrihydrite. The Ca, P and possibly some of the Si may be biogenic. The spectral character of these Icelandic ferrihydrites is compared with those of synthetic ferrihydrites and other iron oxide/oxyhydroxide minerals. Ferrihydrite is characterized by a broad Fe3+ excitation band near 0.92 microns (approx. 10900/cm) and a strong Fe-O absorption feature near 475/cm (approx. 21 microns) in transmittance spectra. Multiple bands due to H2O and OH are also present for ferrihydrite. Natural ferrihydrites frequently exhibit a band near 950-1050/cm (approx. 10 microns) that is typically not observed for synthetic ferrihydrites and may be due to some Si in the structure. An additional pair of spectral bands near 1400 and 1500/cm (approx. 7 microns) are characteristic of pure ferrihydrites from natural and synthetic sources. Hydrothermal springs may have been present at one time on Mars in association with volcanic activity. Ferrihydrite formation in such an environment may have contributed to the ferric oxide-rich surface material on Mars.