Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Materials descriptors for advanced water dissociation catalysts in bipolar membranes

The voltage penalty driving water dissociation (WD) at high current density is a major obstacle in the commercialization of bipolar membrane (BPM) technology for energy devices. Here, in this study, we show that three materials descriptors, that is, electrical conductivity, microscopic surface area and (nominal) surface-hydroxyl coverage, effectively control the kinetics of WD in BPMs. Using these descriptors and optimizing mass loading, we design new earth-abundant WD catalysts based on nanoparticle SnO 2 synthesized at low temperature with high conductivity and hydroxyl coverage. These catalysts exhibit exceptional performance in a BPM electrolyser with low WD overvoltage (η wd ) of 100 ± 20 mV at 1.0 A cm -2 . The new catalyst works equivalently well with hydrocarbon proton-exchange layers as it does with fluorocarbon-based Nafion, thus providing pathways to commercializing advanced BPMs for a broad array of electrolysis, fuel-cell and electrodialys is applications.

Sasmal, Sayantan↗
DOE OSTI2024

Extended Application of State LiDAR Datasets in Locating Orphaned Wells in Appalachian Region

Location inaccuracies in historical and state oil and gas well databases present a major challenge in locating these orphaned wells. To address this, modern scientific methods such as Light Detection and Ranging (LiDAR), aerial magnetic remote sensing, and digital GIS products have been employed. LiDAR technology uses light to detect surface area changes, providing detailed surface views. This is a workflow to process LiDAR data for use in locating orphaned wells.

Gorantla, Vijaya [NETL Site Support Contractor, Na↗
DOE OSTI2021

Ocean Energy Systems Wave Energy Modeling Task 10.4: Numerical Modeling of a Fixed Oscillating Water Column

This paper reports on an ongoing international effort to establish guidelines for numerical modeling of wave energy converters, initiated by the International Energy Agency Technology Collaboration Program for Ocean Energy Systems. Initial results for point absorbers were presented in previous work, and here we present results for a breakwater-mounted Oscillating Water Column (OWC) device. The experimental model is at scale 1:4 relative to a full-scale installation in a water depth of 12.8 m. The power-extracting air turbine is modeled by an orifice plate of 1–2% of the internal chamber surface area. Measurements of chamber surface elevation, air flow through the orifice, and pressure difference across the orifice are compared with numerical calculations using both weakly-nonlinear potential flow theory and computational fluid dynamics. Both compressible- and incompressible-flow models are considered, and the effects of air compressibility are found to have a significant influence on the motion of the internal chamber surface. Recommendations are made for reducing uncertainties in future experimental campaigns, which are critical to enable firm conclusions to be drawn about the relative accuracy of the numerical models. It is well-known that boundary element method solutions of the linear potential flow problem (e.g., WAMIT) are singular at infinite frequency when panels are placed directly on the free surface. This is problematic for time-domain solutions where the value of the added mass matrix at infinite frequency is critical, especially for OWC chambers, which are modeled by zero-mass elements on the free surface. A straightforward rational procedure is described to replace ad-hoc solutions to this problem that have been proposed in the literature.

16 TIDAL AND WAVE POWER↗
DOE OSTI2024

Coupling of Infrared Active Colloidal Quantum Dots and Amorphous Selenium for Fast and Sensitive Photodetection

Colloidal quantum dot (CQD) based infrared (IR) photodetectors offer facile wavelength tunability in the IR and low-cost fabrication. However, owing to their large surface areas, CQDs intrinsically have significant surface traps critically affecting the speed of CQD photodetectors, typically mediated through tedious surface passivation efforts. In this report, an alternative strategy involving coupling of near-IR photoactive lead sulfide CQDs with a thermally evaporated amorphous selenium (a-Se) hole transport layer is proposed. By separating the detector into a photon absorbing CQD region and a charge transport a-Se region, the study takes advantage of the extremely low noise, predominantly hole-only transport process in a-Se. Here, a high 3 dB bandwidth of 2.5 MHz and a competitive specific detectivity of 2.5 × 10 11 Jones at room temperature are demonstrated at 980 nm. This report serves as a first demonstration of strong coupling between an IR active CQD absorber and a-Se, which paves the path to obtain fast and highly photoresponsive IR photodetection in the future.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In–Depth Analysis of the Degradation Mechanisms of High–Nickel, Low/No–Cobalt Layered Oxide Cathodes for Lithium–Ion Batteries

A rational compositional design of high-nickel, cobalt-free layered oxide materials for high-energy and low-cost lithium-ion batteries would be expected to further propel the widespread adoption of electric vehicles (EVs), yet a composition with satisfactory electrochemical properties has yet to emerge. The previous work has demonstrated a promising LiNi 0.883 Mn 0.056 Al 0.061 O 2 (NMA-89) composition that outperformed high-nickel, cobalt-containing analogs in cycling stability and maintained a comparable rate performance and thermal stability. Herein, the capacity fading mechanism of NMA-89 in a pouch full cell with a 4.2 V cutoff is compared to that of its cobalt-containing analogs. The results reveal that particle cracking in LiNi 0.89 Mn 0.055 Co 0.055 O 2 (NMC-89) and LiNi 0.883 Co 0.053 Al 0.064 O 2 (NCA-89) leads to a loss of active material and an increase in surface area, thereby exacerbating structural and surface instabilities, accelerating impedance and polarization growth, and ultimately reducing their capacity retentions. LiNi 0.89 Mn 0.044 Co 0.042 Al 0.013 Mg 0.011 O 2 (NMCAM-89) and NMA-89 experience subdued surface reactions and maintain spherical particle structures, both of which are conducive to their capacity retentions during long-term cycling. Furthermore, this investigation offers insights into how specific transition-metal ions dictate the electrochemical stability of high-Ni layered oxide cathode materials, highlights the benefit of Mn-Al combination in NMA-89, and presents potential strategies to further enhance the performance of this novel class of cathode materials.

degradation mechanisms↗
DOE OSTI2022

An experimental approach for crown to whole-canopy defoliation in forests

Canopy defoliation is an important source of disturbance in forest ecosystems that has rarely been represented in large-scale manipulation experiments. Scalable crown to canopy level experimental defoliation is needed to disentangle the effects of variable intensity, timing, and frequency on forest structure, function, and mortality. We present a novel pressure-washing-based defoliation method that can be implemented at the canopy-scale, throughout the canopy volume, targeted to individual leaves or trees, and completed within a timeframe of hours or days. Pressure washing proved successful at producing consistent leaf-level and whole-canopy defoliation, with 10%–20% reduction in leaf area index and consistent leaf surface area removal across branches and species. This method allows for stand-scale experimentation on defoliation disturbance in forested ecosystems and has the potential for broad application. Studies utilizing this standardized method could promote mechanistic understanding of defoliation effects on ecosystem structure and function and development of synthetic understanding across forest types, ecoregions, and defoliation sources.

Forestry↗
DOE OSTI2024

NIST: Soil Respiration, Moisture, Temperature, Chemistry; and Fine Root Measurements from a Transect Through a Forest Edge, Gaithersburg, Maryland, 2017-2021

This dataset contains soil respiration, moisture, temperature, and chemistry, as well as fine root measurements from the National Institute of Standards and Technology (NIST) Forested Optical Reference for Evaluating Sensor Technology (FOREST) research facility at Gaithersburg, Maryland. Measurements were taken at an existing transect array that begins in a grassy meadow, crosses a sharp forest edge, then a small stream, and finally extends upwards in the interior of the forest at the top of a ridge. There are 6 different landscape positions replicated across three transects in the array. Soil respiration was measured during growing seasons in 2017-2019 (2017-06-02 to 2020-02-27). Pedons (1 m3) were isolated from surrounding tree roots using trenching and a fabric to inhibit root ingrowth. Flux measurements inside the pedons were thus assumed to represent heterotrophic only respiration in 2019, and these fluxes were paired with nearby fluxes assumed to represent total respiration. Deep vertical probes measured volumetric moisture content and temperature at the same points in the array every 10 cm in depth to either 90 cm or 120 cm total depth, at 15 minute intervals, from 2019-2021 (2019-07-09 to 2021-09-10). Soil core samples were collected from each of the array points for three different months in early- to mid-2019 (2019-03-19 to 2019-07-10), at three depths each. Soils were analyzed for gravimetric moisture content; pH; total carbon, nitrogen, and phosphorus; texture; microbial biomass carbon, nitrogen, and phosphorus; extractable dissolved organic carbon, nitrogen, and phosphorus; extractable nitrate and ammonia; and extracellular hydrolytic enzyme activities. The fine roots were separated from the cores and segregated by plant functional type (grass or tree species) and if they were dead or alive. Fine roots were then measured for length, surface area, diameter, and dry mass. This dataset contains four data files in comma separated (*.csv) format. These data serve to deepen our understanding of root and soil processes at forest edges and in transitional zones.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Structural Changes in Films of Pulmonary Surfactant Induced by Surfactant Vesicles

When compressed by the shrinking alveolar surface area during exhalation, films of pulmonary surfactant in situ reduce surface tension to levels, at which surfactant monolayers collapse from the surface in vitro. Vesicles of pulmonary surfactant added below these monolayers slow collapse. X-ray scattering here determined the structural changes that improve stability. Grazing incidence X-ray diffraction on monolayers of extracted calf surfactant detected an ordered phase. Mixtures of dipalmitoyl phosphatidylcholine and cholesterol, but not the phospholipid alone, mimic that structure. At concentrations that stabilize the monolayers, vesicles in the subphase had no effect on the unit cell, and the film remained monomolecular. The added vesicles, however, produced a concentration-dependent increase in the diffracted intensity. These results suggest that the enhanced resistance to collapse results from components of an ordered interfacial phase which partition from subphase to the surface, increasing the area of the ordered structure.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

An Analysis of the Impact of Particle Growth on Transport Losses in Polymer-Electrolyte Fuel Cells

Voltage cycling causes catalyst nanoparticles in polymer-electrolyte fuel cells to grow. The concomitant loss of interfacial area results in larger kinetic, transport, and possibly ohmic overpotentials. This paper uses recently published experimental data and mathematical models to investigate the evolutions of transport and ohmic resistances to platinum nanoparticles located on the surface and inside the micropores of carbon black supports. Resistance to oxygen transport rises as surface area declines primarily because the flux to each remaining larger platinum particle increases. The path lengths governing oxygen diffusion to surface and buried platinum sites also increase as nanoparticles grow. Platinum nanoparticles on the surface become relatively less favorable as voltage cycling proceeds because they grow faster than platinum in micropores. Because voltage cycling causes total interfacial area to decline, and the fraction located inside micropores to increase, nanoscale ohmic losses increase as a catalyst layer decays. The practical importance of this effect is difficult to discern because proton conductivity in carbon micropores is not well characterized.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2023

Review of particle deposition to and removal from clothing, skin, and hair after a radioactive airborne dispersal event

Explosive Radiological Dispersal Devices (RDD) – aka dirty bombs – are seen as a credible method to carry out a radiological terror attack. After exploding a radioactive source, the radionuclide-laden plume will be blown downwind of ground zero, with particles falling out and potentially depositing on people caught in and under the cloud. Some of these people may not show any sign of radiation sickness and therefore not realize they have been contaminated and may take the radioactive particulate with them on their daily activities, thus spreading the radioactive particulate outside the initially contaminated area. This paper reviews the scientific literature to better understand the rate at which particulate deposits on and is removed from the different “surfaces” of a person, i.e., hair, skin, and clothing. Prior research indicates that: 1) particle deposition is usually higher on skin than on hair and clothing; 2) particle deposition is greater for a person with higher skin moisture, 3) stronger wind increases the deposition flux onto a person, and 4) the fraction of particulate deposited on the hair, skin, and clothing respectively depends on the length of the hair, assuming all the hair surface is available for deposition. The studies taken into consideration show that the largest uncertainty in particulate deposition onto a person is due to clothing type because of the different possible weave arrangements and tightness which translate into differences in actual surface area and surface roughness. A factor of 2-to-20 variation in deposition rate was found. Removal of the particulate from the contaminated person may be due to wind, a person's movement, and/or contact transfer, i.e., by touching a different clean surface. Experiments show that the majority of the particulate is resuspended within 2–6 h mostly depending on the intensity of physical activity. The largest uncertainty in particulate removal from skin depends on the skin moisture, transfer rate of single-contact, and how many objects/people a person touches per hour. No data for hair were found for particle removal and resuspension. The studies considered did not utilize radionuclides directly; however, data on adhesion of radioactive vs. their non-radioactive counterpart have shown that the uncertainty due to the radioactivity of the particles is lower than that due to other factors. In conclusion, an idealized scenario involving a single building in the path of the cloud showed the impact of building-influenced flow on the cloud transport path and mixing, which affects the radiological dose the downwind population is exposed to and consequently the health effects.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2025

Depolymerization as a Design Strategy: Depolymerization Etching of Polymerization-Induced Microphase Separations

Thermally triggered depolymerization has traditionally been viewed through the lens of sustainability and recycling, not as a constructive tool for materials design. Herein, we show that selective, thermally triggered depolymerization to gaseous monomer serves as a solvent-free strategy for generating porosity in nanostructured polymer materials, offering a means to bypass the mass transport limitations inherent in conventional solution-based etching. As a demonstration platform, we employed polymerization-induced microphase separation (PIMS) to generate disordered bicontinuous block copolymer structures with embedded depolymerizable domains. By incorporating a methacrylate block susceptible to thermal depolymerization within a cross-linked, depolymerization-resistant styrenic matrix, we developed a process we term depolymerization etching of polymerization-induced microphase separations (DEPIMS). This approach enables highly selective and efficient domain removal via reversion to monomer to produce mesoporous materials with high surface areas (>200 m 2 /g). Subsequent surface functionalization yielded mesoporous adsorbents with tunable uptake kinetics and among the highest dye adsorption capacities reported for PIMS-derived materials, demonstrating the adaptability of the DEPIMS platform for chemical separations. DEPIMS can also be extended to a gram-scale, one-pot approach to yield mesoporous materials with recoverable monomer in under 12 h. These findings reposition thermal depolymerization from a sustainability tool to a broadly enabling strategy for scalable, on-demand fabrication of functional nanostructured materials.

Depolymerization↗
DOE OSTI2023

Bulk Transfer Coefficients Estimated From Eddy-Covariance Measurements Over Lakes and Reservoirs

The drag coefficient, Stanton number and Dalton number are of particular importance for estimating the surface turbulent fluxes of momentum, heat and water vapor using bulk parameterization. Although these bulk transfer coefficients have been extensively studied over the past several decades in marine and large-lake environments, there are no studies analyzing their variability for smaller lakes. Here, we evaluated these coefficients through directly measured surface fluxes using the eddy-covariance technique over more than 30 lakes and reservoirs of different sizes and depths. Our analysis showed that the transfer coefficients (adjusted to neutral atmospheric stability) were generally within the range reported in previous studies for large lakes and oceans. All transfer coefficients exhibit a substantial increase at low wind speeds (<3 m s -1 ), which was found to be associated with the presence of gusts and capillary waves (except Dalton number). Stanton number was found to be on average a factor of 1.3 higher than Dalton number, likely affecting the Bowen ratio method. At high wind speeds, the transfer coefficients remained relatively constant at values of 1.6·10 -3 , 1.4·10 -3 , 1.0·10 -3 , respectively. We found that the variability of the transfer coefficients among the lakes could be associated with lake surface area. In flux parameterizations at lake surfaces, it is recommended to consider variations in the drag coefficient and Stanton number due to wind gustiness and capillary wave roughness while Dalton number could be considered as constant at all wind speeds.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Evaluating Contributions of Pitch-Carbon Coating to Improved Stability of Si Anodes Through Voltage-Resolved Multi-Phase Characterization

Silicon nanoparticles have emerged as a promising alternative to graphite to improve the energy density of next-generation lithium-ion battery anodes. Nano-sized Si domains facilitate rapid ion transport and minimize particle-scale mechanical degradation, but also exhibit increased (electro)chemical reactivity with Li-ion electrolyte components due to their high surface area. We have previously demonstrated that surface modification of Si nanoparticles with pitch-carbon is an effective strategy to reduce these parasitic reactions. In the present work, we holistically evaluate the mechanistic contribution of pitch-carbon coating to the observed stability improvement over uncoated Si. We utilize coupled in situ and ex situ methods to probe changes to solid-surface, volatile headspace, and gas-phase chemistry occurring during initial cycling. Measurements taken at targeted potentials associated with electrolyte species reduction enables the decoupling of specific reaction pathways tied to interfacial stability. Further, we demonstrate the non-trivial role of gas reconsumption in dictating the nature of the passivating surface layer evolved on both uncoated and pitch-coated Si. This multi-phase analysis offers insights into the mechanism of effective surface passivation, which may be applied to inform future Si material development.

ENERGY STORAGE↗
DOE OSTI2023

Study of dielectric breakdown in liquid xenon with XeBrA: The xenon breakdown apparatus

Maintaining the electric fields necessary for the current generation of noble liquid time projection chambers (TPCs), with drift lengths exceeding 1 m, requires a large negative voltage applied to their cathode. Delivering such high voltage is associated with an elevated risk of electrostatic discharge and electroluminescence, which would be detrimental to the performance of the experiment. The Xenon Breakdown Apparatus (XeBrA) is a 5-l, high voltage test chamber built to investigate the contributing factors to electrical breakdown in noble liquids. Here, in this work, we present the main findings after conducting scans over stressed electrode areas, surface finish, pressure, and high voltage ramp speed in the medium of liquid xenon. Area scaling and surface finish were observed to be the dominant factors affecting breakdown, whereas no significant changes were observed with varying pressure or ramp speed. A general rise in both the anode current and photon rate was observed in the last 30 s, leading up to a breakdown, with a marked increase in the last couple of seconds. In addition, the position of breakdowns was reconstructed with a system of high-speed cameras and a moderate correlation with the Fowler–Nordheim field emission model was found. Tentative evidence for bubble nucleation being the originating mechanism of breakdown in the liquid was also observed. We deem the results presented in this work to be of particular interest for the design of future, large TPCs, and practical recommendations are provided.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Effects of blended cements and carbonation on chloride-induced corrosion propagation

Highlights: • Corrosion propagation of blended cements was investigated for 1 year. • Carbonated and non‑carbonated mortars were evaluated. • Galvanostatic pulse and ER sensors were used to monitor corrosion. • Mortar properties were correlated with corrosion rates and corrosion damage. • Relationships between mortar properties and corrosion behaviour were established. Supplementary cementitious materials are known to refine the pore structure of concrete and accelerate the carbonation progress. The combination of the two processes can have both beneficial and disadvantageous effects on corrosion, especially when chlorides are also involved. In this study the corrosion properties of multiple blended cements were evaluated in carbonated and non‑carbonated states, with chlorides introduced through cyclic ponding. The examination involved monitoring the propagation phase, determining the microstructural properties of cements, and assessing the final corrosion damage. The results showed that the steel in the blended cements initially had a relatively high corrosion activity, which later decreased compared to the OPC. This stabilisation was presumably due to the beneficial changes to the pore structure. Carbonation had a significant impact on the corrosion, with carbonated mortars revealing shallower damage over a larger surface area. This effect was more pronounced for blended cements that exhibited greater susceptibility to carbonation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Impact of limestone fineness on cement hydration at early age

This study compares the influence of two limestone fineness on strength development and cement hydration. The replacement of clinker by 20% of fine limestone (d{sub v,50} = 2 μm and SSA = 4,21 m{sup 2}/g) gives similar strength development to PC up to 7 days. Fine limestone enhances cement hydration and offsets the dilution effect caused by the decrease of clinker amount. The accelerating effect of the limestone was explained by a higher degree of undersaturation with respect to C{sub 3}S. The influence of coarse limestone (d{sub v,50} = 130 μm and SSA = 0,46 m{sup 2}/g) on cement hydration is limited to dilution effect. The combination of fine and coarse limestone was also studied. A linear correlation was obtained between strength and gel space ratio for all investigated systems. Furthermore, the results showed that despite the similarity of specific surface area, limestone is more effective than quartz for the enhancement of cement hydration.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Upgrading the Performance and Stability of Lithium, Manganese-Rich Layered Oxide Cathodes with Combined-Formic Acid and Spinel Coating Treatment

We report improving sluggish rate performance and cycling stability of Li, Mn-rich cathode materials (LMR) is of great importance for practical implementation. Here, dual surface modification on LMR particles with formic acid washing and spinel coating improves the electrochemical performance. Dilute formic acid can remove the Li2CO3 surface impurities and selectively reduce Ni while significantly increasing specific surface area by ~32 %, unlocking more electrochemically active surfaces. Spinel coating enhances cycle stability by suppressing detrimental side reactions at electrode-electrolyte interfaces at high voltage. Post-annealing temperature was found to significantly affect the cathode performance. Higher temperature favors diffusion of transition metal (TM)/Li ions of the spinel coating from surface to the bulk, removing the coating by possible reconstruction into the layered structure and thus degrading the performance. The spinel coating also appears to increase Co 3+ segregation on the particle surface. Compared to the original material, the optimized sample demonstrates 47 % higher capacity retention at 3C and retains 89 % of initial capacity after 150 cycles at 0.5C. Besides, the specific energy density of 523 Wh kg -1 can be attained after 150 cycles at 0.5C. Moreover, the post-cycling analysis of modified sample verifies a better structural integrity with less particle cracking. Altogether, this study portrays an alternative strategy to overcome the shortcomings of LMR cathode materials.

25 ENERGY STORAGE↗