SEARCH · Engineering Papers

Results for “smoothing technique”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Optimization of self-acting herringbone-grooved journal bearings for maximum stability

Groove parameters were determined to maximize the stability of herringbone-grooved journal bearings. Parameters optimized were groove depth, width, length, and angle. Optimization was performed by using a small-eccentricity, infinite-groove analysis in conjunction with a previously developed Newton-Raphson procedure for bearings with the smooth member rotating or with the grooved member rotating at low compressibility numbers, and a newly developed vector technique for bearings with the grooved member rotating at high compressibility numbers. The design curves in this report enable one to choose the optimum bearing for a wide range of operating conditions. Compared with bearings optimized to maximize load capacity, bearings optimized for stability allow a thousandfold increase in bearing-supported mass in some cases before onset of instability, and lose no more than 77 percent of their load capacity in any case studied. Stability is much greater when the grooved member rotates.

Fleming, D. P.↗

NASA NTRS1976

Chemiluminescent prediction of service life

Technique can be used to predict polymer degradation under actual expected-use conditions, without imposing artificial conditions. Smooth or linear correlations are obtained between chemiluminescence and physical properties of purified polymer gums.

Hassell, J. A.↗

NASA NTRS1981

Optimum structural design with plate bending elements - A survey

A survey is presented of recently published papers in the field of optimum structural design of plates, largely with respect to the minimum-weight design of plates subject to such constraints as fundamental frequency maximization. It is shown that, due to the availability of powerful computers, the trend in optimum plate design is away from methods tailored to specific geometry and loads and toward methods that can be easily programmed for any kind of plate, such as finite element methods. A corresponding shift is seen in optimization from variational techniques to numerical optimization algorithms. Among the topics covered are fully stressed design and optimality criteria, mathematical programming, smooth and ribbed designs, design against plastic collapse, buckling constraints, and vibration constraints.

Haftka, R. T.↗

NASA NTRS1982

Analysis of general-aviation accidents using ATC radar records

It is pointed out that general aviation aircraft usually do not carry flight recorders, and in accident investigations the only available data may come from the Air Traffic Control (ATC) records. A description is presented of a technique for deriving time-histories of aircraft motions from ATC radar records. The employed procedure involves a smoothing of the raw radar data. The smoothed results, in combination with other available information (meteorological data and aircraft aerodynamic data) are used to derive the expanded set of motion time-histories. Applications of the considered analytical methods are related to different types of aircraft, such as light piston-props, executive jets, and commuter turboprops, as well as different accident situations, such as takeoff, climb-out, icing, and deep stall.

Wingrove, R. C.↗

NASA NTRS1982

Automatic evaluation of interferograms

A system for the evaluation of interference patterns was developed. For digitizing and processing of the interferograms from classical and holographic interferometers a picture analysis system based upon a computer with a television digitizer was installed. Depending on the quality of the interferograms, four different picture enhancement operations may be used: Signal averaging; spatial smoothing, subtraction of the overlayed intensity function and the removal of distortion-patterns using a spatial filtering technique in the frequency spectrum of the interferograms. The extraction of fringe loci from the digitized interferograms is performed by a foating-threshold method. The fringes are numbered using a special scheme after the removal of any fringe disconnections which appeared if there was insufficient contrast in the holograms. The reconstruction of the object function from the fringe field uses least squares approximation with spline fit. Applications are given.

Becker, F.↗

NASA NTRS1987

Investigation of PTFE transfer films by infrared emission spectroscopy and phase-locked ellipsometry

When a PTFE sheet was rubbed unidirectionally over a smooth surface of stainless steel an essentially monomolecular transfer film was formed. By ellipsometric and emission infrared spectroscopic techniques it was shown that the film was 10 to 15 A thick and birefringent. From the intensity differences of infrared bands obtained with a polarizer passing radiation polarized in mutually perpendicular planes, it was possible to deduce transfer film orientation with the direction of rubbing. After standing in air for several weeks the transfer films apparently increased in thickness by as much as threefold. At the same time both the index of refraction and the absorption index decreased. Examination of the surfaces by optical and electron microscopies showed that the films had become porous and flaky. These observations were consistent with previous tribological measurements. The coefficients of friction decreased with the formation of the transfer film but increased again as the film developed breaks. The applicability of the ellipsometric and polarized infrared emission techniques to the identification of monomolecular tribological transfer films of polymers such as PTFE has been demonstrated.

Lauer, James L.↗

NASA NTRS1988

Investigation of PTFE transfer films by infrared emission spectroscopy and phase-locked ellipsometry

When a PTFE sheet was rubbed unidirectionally over a smooth surface of stainless steel an essentially monomolecular transfer film was formed. by ellipsometric and emission infrared spectroscopic techniques it was shown that the film was 10 to 15 A thick and birefringent. From the intensity differences of infrared bands obtained with a polarizer passing radiation polarized in mutually perpendicular planes, it was possible to deduce transfer film orientation with the direction of rubbing. After standing in air for several weeks the transfer films apparently increased in thickness by as much as threefold. At the same time both the index of refraction and the absorption index decreased. Examination of the surfaces by optical and electron microscopies showed that the films had become porous and flaky. These observations were consistent with previous tribological measurements. The coefficients of friction decreased with the formation of the transfer film but increased again as the film developed breaks. The applicability of the ellipsometric and polarized infrared emission techniques to the identification of monomolecular tribological transfer films of polymers such as PTFE has been demonstrated.

Lauer, James L.↗

NASA NTRS1993

Improved Blending-Function Algebraic Generation Of Grids

Method of algebraic generation of grids used in computing flows incorporates blending-function techniques to obtain high degree of orthogonality of each grid on its bounding surfaces and to blend grid smoothly, making it conform to all boundaries. Demonstrated in two dimensions, and applied in continuing development of software for real-time interactive generation of three-dimensional grids with color graphical displays. Software used routinely in generating grids for computing flows of practical interest.

Ching-Chung Luh, Raymond↗

NASA NTRS1993

Adjoint methods for aerodynamic wing design

A model inverse design problem is used to investigate the effect of flow discontinuities on the optimization process. The optimization involves finding the cross-sectional area distribution of a duct that produces velocities that closely match a targeted velocity distribution. Quasi-one-dimensional flow theory is used, and the target is chosen to have a shock wave in its distribution. The objective function which quantifies the difference between the targeted and calculated velocity distributions may become non-smooth due to the interaction between the shock and the discretization of the flowfield. This paper offers two techniques to resolve the resulting problems for the optimization algorithms. The first, shock-fitting, involves careful integration of the objective function through the shock wave. The second, coordinate straining with shock penalty, uses a coordinate transformation to align the calculated shock with the target and then adds a penalty proportional to the square of the distance between the shocks. The techniques are tested using several popular sensitivity and optimization methods, including finite-differences, and direct and adjoint discrete sensitivity methods. Two optimization strategies, Gauss-Newton and sequential quadratic programming (SQP), are used to drive the objective function to a minimum.

Grossman, Bernard↗

NASA NTRS1996

Development of an Automatic Grid Generator for Multi-Element High-Lift Wings

The procedure to generate the grid around a complex wing configuration is presented in this report. The automatic grid generation utilizes the Modified Advancing Front Method as a predictor and an elliptic scheme as a corrector. The scheme will advance the surface grid one cell outward and the newly obtained grid is corrected using the Laplace equation. The predictor-corrector step ensures that the grid produced will be smooth for every configuration. The predictor-corrector scheme is extended for a complex wing configuration. A new technique is developed to deal with the grid generation in the wing-gaps and on the flaps. It will create the grids that fill the gap on the wing surface and the gap created by the flaps. The scheme recognizes these configurations automatically so that minimal user input is required. By utilizing an appropriate sequence in advancing the grid points on a wing surface, the automatic grid generation for complex wing configurations is achieved.

Eberhardt, Scott↗

NASA NTRS1985

The X-ray halo of Cygnus X-1

Four Einstein HRI images of Cygnus X-1 were examined for the presence of a halo due to scattering of X-rays by interstellar grains. The analysis technique exploits the intrinsic aperiodic variability of the source to map the point response function of the optics. A residual, nonvariable component to the surface brightness distribution (comprising approximately more than 12 percent of the source flux) is interpreted as a scattered halo. The halo flux does not reflect the short term time variability of the central source as it is smoothed by differential time delays of order days. The Cygnus X-1 halo is consistent with those of other sources derived in previous studies using different techniques. Comparison is made with a scattering model, and the sensitivity of the halo flux to maximal grain size is demonstrated.

Bode, M. F.↗

NASA NTRS1989

Numerical simulation of flow over a hypersonic aircraft using an explicit upwind PNS solver

A hypersonic flow field over a generic airplane configuration is simulated by solving the Parabolized Navier-Stokes (PNS) equations. The finite difference solution of the PNS equations is calculated using a noniterative space marching, explicit, upwind scheme recently developed by the authors. Special gridding techniques are used which allowed the sharp changes in surface geometry of the airplane configuration to be modelled without smoothing of corners. Comparisons of the PNS results to a solution of the Navier-Stokes equations demonstrates a good agreement of the numerical results in approximately 1/6 of the cpu time. This paper demonstrates that the explicit upwind algorithm for solving the PNS equations is an efficient method for simulating hypersonic flow fields about complete airplane configurations and should be considered as an alternative to solving the Navier-Stokes equations for flow fields where the PNS equations are valid.

Korte, John J.↗

NASA NTRS1991

Photographic Image Restoration

Deblurring capabilities would significantly improve the Flight Science Support Office's ability to monitor the effects of lift-off on the shuttle and landing on the orbiter. A deblurring program was written and implemented to extract information from blurred images containing a straight line or edge and to use that information to deblur the image. The program was successfully applied to an image blurred by improper focussing and two blurred by different amounts of blurring. In all cases, the reconstructed modulation transfer function not only had the same zero contours as the Fourier transform of the blurred image but the associated point spread function also had structure not easily described by simple parameterizations. The difficulties posed by the presence of noise in the blurred image necessitated special consideration. An amplitude modification technique was developed for the zero contours of the modulation transfer function at low to moderate frequencies and a smooth filter was used to suppress high frequency noise.

Hite, Gerald E.↗

NASA NTRS1992

Analysis of scattering behavior and radar penetration in AIRSAR data

A technique is presented to physically characterize changes in radar backscatter with frequency in multifrequency single polarization radar images that can be used as a first step in the analysis of the data and the retrieval of geophysical parameters. The technique is automatic, relatively independent of the incidence angle, and only requires a good calibration accuracy between the different frequencies. The technique reveals large areas where scattering changes significantly with frequency and whether the surface has the characteristics of a smooth, slightly rough, rough, or very rough surface.

Rignot, Eric↗

NASA NTRS2008

Effect of the Inhomogeneity of Ice Crystals on Retrieving Ice Cloud Optical Thickness and Effective Particle Size

Spherical or spheroidal air bubbles are generally trapped in the formation of rapidly growing ice crystals. In this study the single-scattering properties of inhomogeneous ice crystals containing air bubbles are investigated. Specifically, a computational model based on an improved geometric-optics method (IGOM) has been developed to simulate the scattering of light by randomly oriented hexagonal ice crystals containing spherical or spheroidal air bubbles. A combination of the ray-tracing technique and the Monte Carlo method is used. The effect of the air bubbles within ice crystals is to smooth the phase functions, diminish the 22deg and 46deg halo peaks, and substantially reduce the backscatter relative to bubble-free particles. These features vary with the number, sizes, locations and shapes of the air bubbles within ice crystals. Moreover, the asymmetry factors of inhomogeneous ice crystals decrease as the volume of air bubbles increases. Cloud reflectance lookup tables were generated at wavelengths 0.65 m and 2.13 m with different air-bubble conditions to examine the impact of the bubbles on retrieving ice cloud optical thickness and effective particle size. The reflectances simulated for inhomogeneous ice crystals are slightly larger than those computed for homogenous ice crystals at a wavelength of 0.65 microns. Thus, the retrieved cloud optical thicknesses are reduced by employing inhomogeneous ice cloud models. At a wavelength of 2.13 microns, including air bubbles in ice cloud models may also increase the reflectance. This effect implies that the retrieved effective particle sizes for inhomogeneous ice crystals are larger than those retrieved for homogeneous ice crystals, particularly, in the case of large air bubbles.

Xie, Yu↗

NASA NTRS1982

On conforming mixed finite element methods for incompressible viscous flow problems

The application of conforming mixed finite element methods to obtain approximate solutions of linearized Navier-Stokes equations is examined. Attention is given to the convergence rates of various finite element approximations of the pressure and the velocity field. The optimality of the convergence rates are addressed in terms of comparisons of the approximation convergence to a smooth solution in relation to the best approximation available for the finite element space used. Consideration is also devoted to techniques for efficient use of a Gaussian elimination algorithm to obtain a solution to a system of linear algebraic equations derived by finite element discretizations of linear partial differential equations.

Gunzburger, M. D↗

NASA NTRS1983

Surfaces

Techniques for the characterization of surface cleanliness and roughness for predicting the quality of an adhesive bond are outlined. Generally, smooth surfaces are only available from cleavage of crystalline materials along a natural cleavage plane. Films must be deposited on metal surfaces to achieve the same smoothness. Once the surfaces are clean, however, reaction with the ambient atmosphere becomes likely through diffusive and absorption processes, producing asperities. Electron diffraction, Auger electron, and X ray emission spectroscopy are used to characterize surface condition. Once the surface is observed to be clean, the application of an adhesive will usually prohibit separation along the adhesive; separation is then confined to the weaker of the two materials. Finally, the use of polytetrafluorothylene adhesive to test the adhesion between polymers and metal surfaces is described.

Buckley, D. H.↗

NASA NTRS1986

Thrust imbalance of solid rocket motor pairs on Space Shuttle flights

This analysis extends the investigation presented at the 17th Joint Propulsion Conference in 1981 to include fifteen sets of Space Shuttle flight data. The previous report dealt only with static test data and the first flight pair. The objective is to compare the authors' previous theoretical analysis of thrust imbalance with actual Space Shuttle performance. The theoretical prediction method, which involves a Monte Carlo technique, is reviewed briefly as are salient features of the flight instrumentation system and the statistical analysis. A scheme for smoothing flight data is discussed. The effects of changes in design parameters are discussed with special emphasis on the filament wound motor case being developed to replace the steel case. Good agreement between the predictions and the flight data is demonstrated.

Foster, W. A., Jr.↗