Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “single experiment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

An experimental study of adsorption interference in binary mixtures flowing through activated carbon

The isothermal transmission through activated carbon adsorber beds at 25 C of acetaldehyde-propane and acetylene-ethane mixtures in a helium carrier gas was measured. The inlet concentration of each component was in the range between 10 ppm and 500 ppm. The constant inlet volumetric flow rate was controlled at 200 cc (STP)/min in the acetaldehyde-propane experiments and at 50 cc (STP)/min in the acetaldehyde-ethane experiments. Comparison of experimental results with the corresponding single-component experiments under similar conditions reveals interference phenomena between the components of the mixtures as evidenced by changes in both the adsorption capacity and the dispersion number. Propane was found to displace acetaldehyde from the adsorbed state. The outlet concentration profiles of propane in the binary mixtures tend to become more diffuse than the corresponding concentration profiles of the one-component experiments. Similar features were observed with mixtures of acetylene and ethane; however, the displacement of acetylene by ethane is less pronounced.

Madey, R.↗

Status and Planned Experiments of the Hiradmat Pulsed Beam Material Test Facility at CERN SPS

HiRadMat (High Irradiation to Materials) is a facility at CERN designed to provide high-intensity pulsed beams to an irradiation area where material samples as well as accelerator component assemblies (e.g. vacuum windows, shock tests on high power targets, collimators) can be tested. The beam parameters (SPS 440 GeV protons with a pulse energy of up to 3.4 MJ, or alternatively lead/argon ions at the proton equivalent energy) can be tuned to match the needs of each experiment. It is a test area designed to perform single pulse experiments to evaluate the effect of high-intensity pulsed beams on materials in a dedicated environment, excluding long-time irradiation studies. The facility is designed for a maximum number of 1016 protons per year, in order to limit the activation of the irradiated samples to acceptable levels for human intervention. This paper will demonstrate the possibilities for research using this facility and go through examples of upcoming experiments scheduled in the beam period 2015/2016.

43 PARTICLE ACCELERATORS↗

HiRadMat at CERN SPS - A test facility with high intensity beam pulses to material samples

HiRadMat (High Irradiation to Materials) is a facility at CERN designed to provide high-intensity pulsed beams to an irradiation area where material samples as well as accelerator component assemblies (e.g. vacuum windows, shock tests on high power targets, collimators) can be tested. The beam parameters (SPS 440 GeV protons with a pulse energy of up to 3.4 MJ, or alternatively lead/argon ions at the proton equivalent energy) can be tuned to match the needs of each experiment. It is a test area designed to perform single pulse experiments to evaluate the effect of high-intensity pulsed beams on materials in a dedicated environment, excluding long-time irradiation studies. The facility is designed for a 10{sup 16} maximum number of protons per year, in order to limit the activation to acceptable levels for human intervention. This paper will demonstrate the possibilities for research using this facility and showing examples of upcoming experiments scheduled in the beam period 2014/2015. (authors)

43 PARTICLE ACCELERATORS↗

Absolute single photoionization cross-section measurements of Rb 2+ ions: experiment and theory

Absolute single photoionization cross-section measurements of Rb 2+ ions were performed at the Advanced Light Source at Lawrence Berkeley National Laboratory using synchrotron radiation and the photo-ion, merged-beams technique. Measurements were made at a photon energy resolution of 13.5 2.5 meV from 37.31 to 44.08 eV spanning the 2 P ground state and 2 P metastable state ionization thresholds. Multiple autoionizing resonance series arising from each initial state are identified using quantum defect theory. The measurements are compared to Breit-Pauli R-matrix calculations with excellent agreement between theory and experiment.

74 ATOMIC AND MOLECULAR PHYSICS↗

Quantifying Impacts of Biomass Pelletization on Fast Pyrolysis Using a Single-Particle Reactor, X-ray Computed Tomography, and Computational Modeling

The pore structure and density of lignocellulosic feedstocks dictate intraparticle transport phenomena and thereby play an important role in thermochemical conversion processes such as fast pyrolysis for biofuel and biochemical production. Variations in microstructure are inherent from different biomass species and can be introduced by preprocessing techniques such as cutting and pelletization. Morphological changes also occur during conversion and lead to vastly different pore structures and behavior during pyrolysis, which impact required conversion times and product distributions. The current work presents a comprehensive comparison of fast pyrolysis of neat and pelletized pine feedstocks, which includes single-particle experiments, modeling, and 3D imaging by X-ray computed tomography (XCT). The particle-scale model included anisotropic heat and mass transport in a shrinking particle with pyrolysis reactions based on the CRECK mechanism with boundary conditions informed by reactor-scale simulations of the single-particle reactor. The models were validated by measurements of the temperature and mass loss from single-particle pyrolysis experiments of neat and pelletized pine. Quantitative analysis of XCT geometries revealed that pyrolytic conversion yielded chars with increased porosity and permeability compared to the unpyrolyzed materials, along with decreased tortuosity and anisotropy. Pelletization of the pine feedstock resulted in a much denser, less permeable material, which converted slower and produced more residual char after pyrolysis compared to neat pine. The results from particle modeling revealed that accounting for the dynamic and anisotropic heat and mass transport caused by differences in pore structure is critical to achieving agreement with experimental results. Overall, this study highlights the dramatic differences in conversion behavior imparted by pelletization and the importance of capturing microstructural attributes in computational models to guide the design and optimization of pyrolysis processes for specific biomass feedstocks.

09 BIOMASS FUELS↗

Measurement of cavity perturbation to determine the microwave absorption of a sphere in a single mode resonator

Experiments have been conducted on materials in a single mode microwave resonator to test predictions of a new theory of microwave absorption by a lossy dielectric sphere. An analysis of cavity perturbation for verifying the new absorption model revealed a limitation of a standard form of cavity perturbation theory and led to a modification which generalized its application. The cavity perturbations of a nylon sphere were used to calculate the complex permittivity using the standard perturbation theory and the modified form. These permittivity values were compared to that determined from cavity perturbation using a thin nylon rod where the standard and modified forms agree. The results show that the modification is necessary to correctly apply perturbation theory to spherical samples. A second experiment confirmed the theoretical prediction that under certain sample conditions the power absorbed by a sphere in a resonant cavity can be maximum at a location in the cavity where the empty cavity electric field intensity is a minimum.

Watkins, J. L.↗

Design of a single-mode Rayleigh–Taylor instability experiment in the highly nonlinear regime

An experimental design, intended to investigate the evolution of the single mode Rayleigh–Taylor (RT) instability in the late time regime is proposed and theoretically analyzed. The goal of the experiment is to directly measure the evolution of the shape of the interface in time, for both low and high-Atwood numbers (A~0.0.15 and A~0.6). An objective of this study is to assess the degree to which, using 10-kJ-class lasers, one can expect to observe the predicted re-acceleration of the height of structures produced by RT, which occurs in low-A simulations. The specific design presented here shows no effects of x-ray preheat, and tolerable effects of 2D rarefactions. Observation of the reacceleration effect, at the 10-kJ scale, appears marginal for the design presented here. Finally, experiments could serve to test and validate the numerical results, and determine whether a larger-scale laser would be needed to actually observe the reacceleration effect.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Density of Additively-Manufactured, 316L SS Parts Using Laser Powder-Bed Fusion at Powers Up to 400W

Selective laser melting is a powder-based, additive-manufacturing process where a threedimensional part is produced, layer by layer, by using a high-energy laser beam to fuse the metallic powder particles. A particular challenge in this process is the selection of appropriate process parameters that result in parts with desired properties. In this study, we describe an approach to selecting parameters for high density (>99%) parts using 316L stainless steel. Though there has been significant success in achieving near-full density for 316L parts, this work has been limited to laser powers <225W. We discuss how we can exploit prior knowledge, design of computational experiments using a simple model of laser melting, and single-track experiments to determine the process parameters for use at laser powers up to 400W. Our results show that, at higher power values, there is a large range of scan speeds over which the relative density remains >99%, with the density reducing rapidly at high speeds due to insufficient melting, and less rapidly at low speeds due to the effect of voids created as the process enters keyhole mode.

316L stainless teel↗

Diamond sensors and polycapillary lenses for X-ray absorption spectroscopy

Diamond sensors are evaluated as incident beam monitors for X-ray absorption spectroscopy experiments. These single crystal devices pose a challenge for an energy-scanning experiment using hard X-rays due to the effect of diffraction from the crystalline sensor at energies which meet the Bragg condition. This problem is eliminated by combination with polycapillary lenses. The convergence angle of the beam exiting the lens is large compared to rocking curve widths of the diamond. A ray exiting one capillary from the lens meets the Bragg condition for any reflection at a different energy from the rays exiting adjacent capillaries. This serves to broaden each diffraction peak over a wide energy range, allowing linear measurement of incident intensity over the range of the energy scan. Extended X-ray absorption fine structure data are measured with a combination of a polycapillary lens and a diamond incident beam monitor. These data are of comparable quality to data measured without a lens and with an ionization chamber monitoring the incident beam intensity.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A Mechanistic Study of Nucleate Boiling Under Microgravity Conditions

The overall objective of this work is to study nucleate boiling heat transfer under microgravity conditions in such a way that while providing basic knowledge of the phenomena, it also leads to development of simulation models and correlations that can be used as design tools for a wide range of gravity levels. In the study a building block type of approach is used and both pool and low velocity flow boiling are investigated. Starting with experiments using a single bubble, the complexity of the experiments is increased to two or three inline bubbles, to five bubbles placed on a two-dimensional grid. Finally, experiments are conducted where a large number of prescribed cavities nucleate on the heater and when a commercial surface is used. So far experiments have been conducted at earth normal gravity and in the reduced gravity environment of the KC-135 aircraft whereas experiments on the space station are planned. Modeling/complete numerical simulation of the boiling process is an integral part of the total effort. Experiments conducted with single bubbles formed on a nucleation site microfabricated on a polished silicon wafer show that for gravity levels (g) varying from 1.5g(sub e) to 0.01g(sub e), the bubble diameter at departure varies approximately as (g(sub e)/g)(exp 1/2) and the growth period as (g(sub e)/g). When bubbles merge either inline or in a plane, the bubble diameter at departure is found to be smaller than that obtained for a single bubble and shows a weaker dependence on the level of gravity. The possible reason is that as the bubbles merge they create fluid circulation around the bubbles, which in turn induces a lift force that is responsible for the earlier departure of the bubbles. The verification of this proposition is being sought through numerical simulations. There is a merger of two inline, three inline, and several bubbles in a plane in the low gravity environment of the KC-135 aircraft. After merger and before departure, a mushroom type of bubble with several stems attached to the heater surface is clearly evident. Local heat fluxes during growth and departure of a single bubble were also measured. It was found that during most of the growth period of the bubble, generally the wall heat flux decreased with time because of the increased dry area under the bubble. However, the heat flux increased rapidly just prior to departure of the bubble because of the transient conduction into the cold liquid rushing to fill the space vacated by the bubble as the bubble base shrinks. The measured heat fluxes at various radial locations are found to be in qualitative agreement with the numerical predictions. Single bubble studies at earth normal gravity have also been performed on surfaces oriented at different angles to the gravitational acceleration with flow parallel to the surface. It is found that in all cases the bubbles slide along the surface before lift-off from the surface. The lift force generated as a result of the relative motion between the sliding bubbles and the imposed flow is found to play an important role when the normal force due to buoyancy is reduced. An experimental apparatus for the study of the bubble behavior with imposed flow under reduced gravity conditions has been developed and will soon be employed for experiments in the KC-135 aircraft.

Dhir, V. K.↗

Effect of dilute Rh on oxygen dissociation, spillover, and the oxidation of Cu across many orders of magnitude pressure

Knowledge of how trace amounts of more reactive metals influence the oxidation rate and mechanism of Cu surfaces is essential for developing strategies to optimize the performance of Cu-based catalysts. We find that the addition of 1% Rh to Cu(111) increases the initial O 2 dissociation rate by approximately 9-fold. CO poisoning experiments reveal that single Rh atoms activate O 2 and facilitate the spillover of atomic oxygen to Cu sites. Scanning tunneling microscopy (STM) and in situ X-ray photoelectron spectroscopy (XPS) support this mechanism, showing enhanced surface oxygen near Rh atoms. Here, a density functional theory (DFT)-based model demonstrates that Rh binds the O 2 precursor 0.15 eV more strongly than Cu(111) and lowers the O 2 dissociation barrier by 0.02 eV. Both single-crystal and nanoparticle experiments show that at low oxygen pressures, Rh enhances Cu oxidation, whereas at higher pressures, it inhibits deeper oxidation, as evidenced by in situ ultraviolet-visible (UV-vis) spectra.

36 MATERIALS SCIENCE↗

Robust light harvesting by a noisy antenna

Ultrafast bulk and single-molecule spectroscopy experiments described by a single theoretical model show how protein fluctuations influence photosynthetic light harvesting.

14 SOLAR ENERGY↗

Mechanism of the wurtzite to rocksalt phase transformation in cadmium sulfide single crystals shock compressed along the 𝑐-axis to elastic impact stresses of ∼ 5 GPa

Cadmium sulfide (CdS), which exhibits a wurzite (WZ) to rocksalt (RS) phase transformation at elevated stresses, is an ideal system to address the role of deformation on phase transformation mechanisms and kinetics. CdS has been shown to have very different elastic-inelastic behavior for shock propagation along the WZ 𝑐- and 𝑎-axes, and also exhibits significant differences in the time scale for the phase transformation when shocked along these different axes. As an important first step in examining the role of deformation in shock-induced phase transformations, here we present in situ, time-resolved x-ray diffraction (XRD) measurements in single-event, shock wave experiments on CdS single crystals shocked along the WZ 𝑐-axis to elastic impact stresses near or above ∼ 5 GPa, where a marked increase in the kinetics of this transformation has been reported. The XRD measurements are compared with forward diffraction simulations to evaluate different proposed phase transformation mechanisms and are shown to be consistent with a shearing mechanism that results in the RS [001] direction being aligned with the original WZ 𝑐-axis and the RS [110] direction being aligned with the original WZ 𝑎-axis. In order to reproduce all observed RS diffraction spots the forward diffraction simulations required three different RS crystalline domains, each with a [110] direction aligned with one of the three original WZ 𝑎-axes, and a significant mosaicity, particularly about the RS [001] direction (the direction of shock propagation). In conclusion, this large mosaicity is likely due to variations in the possible shearing mechanisms that connect the WZ and RS structures, which can create crystallites with up to ∼ ±10° of relative rotations about the RS [001] direction, as well as further rotation of these crystallites as they grow, merge, and coalesce.

Crystal structure↗

Validation of a fault-tolerant multiprocessor: Baseline experiments and workload implementation

In the future, aircraft must employ highly reliable multiprocessors in order to achieve flight safety. Such computers must be experimentally validated before they are deployed. This project outlines a methodology for validating reliable multiprocessors. The methodology begins with baseline experiments, which tests a single phenomenon. As experiments progress, tools for performance testing are developed. The methodology is used, in part, on the Fault Tolerant Multiprocessor (FTMP) at NASA-Langley's AIRLAB facility. Experiments are designed to evaluate the fault-free performance of the system. Presented are the results of interrupt baseline experiments performed on FTMP. Interrupt causing exception conditions were tested, and several were found to have unimplemented interrupt handling software while one had an unimplemented interrupt vector. A synthetic workload model for realtime multiprocessors is then developed as an application level performance analysis tool. Details of the workload implementation and calibration are presented. Both the experimental methodology and the synthetic workload model are general enough to be applicable to reliable multiprocessors beside FTMP.

Feather, Frank↗

Development of a verification program for deployable truss advanced technology

Use of large deployable space structures to satisfy the growth demands of space systems is contingent upon reducing the associated risks that pervade many related technical disciplines. The overall objectives of this program was to develop a detailed plan to verify deployable truss advanced technology applicable to future large space structures and to develop a preliminary design of a deployable truss reflector/beam structure for use a a technology demonstration test article. The planning is based on a Shuttle flight experiment program using deployable 5 and 15 meter aperture tetrahedral truss reflections and a 20 m long deployable truss beam structure. The plan addresses validation of analytical methods, the degree to which ground testing adequately simulates flight and in-space testing requirements for large precision antenna designs. Based on an assessment of future NASA and DOD space system requirements, the program was developed to verify four critical technology areas: deployment, shape accuracy and control, pointing and alignment, and articulation and maneuvers. The flight experiment technology verification objectives can be met using two shuttle flights with the total experiment integrated on a single Shuttle Test Experiment Platform (STEP) and a Mission Peculiar Experiment Support Structure (MPESS). First flight of the experiment can be achieved 60 months after go-ahead with a total program duration of 90 months.

Dyer, Jack E.↗

A Comparison of Metamodeling Techniques via Numerical Experiments

This paper presents a comparative analysis of a few metamodeling techniques using numerical experiments for the single input-single output case. These experiments enable comparing the models' predictions with the phenomenon they are aiming to describe as more data is made available. These techniques include (i) prediction intervals associated with a least squares parameter estimate, (ii) Bayesian credible intervals, (iii) Gaussian process models, and (iv) interval predictor models. Aspects being compared are computational complexity, accuracy (i.e., the degree to which the resulting prediction conforms to the actual Data Generating Mechanism), reliability (i.e., the probability that new observations will fall inside the predicted interval), sensitivity to outliers, extrapolation properties, ease of use, and asymptotic behavior. The numerical experiments describe typical application scenarios that challenge the underlying assumptions supporting most metamodeling techniques.

Crespo, Luis G.↗

Muon neutrino charged current single pion production on various targets in the MINERvA detector

Measurements of neutrino oscillation parameters at accelerator-based experiments require precise knowledge of neutrino interaction cross sections. A significant fraction of neutrino interactions observed in these experiments produce single charged pions. While single charged pion production has been measured on hydrocarbon and water, few precise measurements exist for heavier targets, and there are no high statistics measurements that directly compare pion production on different targets. This thesis measures differential cross sections of muon neutrino charged current single charged pion production with no other mesons in the final state in a neutrinobeam with a mean energy of ≈ 6 GeV. The pion production is studied on targets of scintillator, carbon, water, iron, and lead at MINERvA, a neutrino cross section experiment located in the NuMI beamline at Fermilab. These measured cross sections are differential in μ - and π + kinematics. A strong suppression of low Q 2 and an enhancement of low π are observed relative to commonly used neutrino interaction models in both the light and heavy nuclear targets. Incorporation of these observed effects in future neutrino oscillation experiments will improve their ability to measure energy of neutrino interactions, and therefore measure the parameters governing neutrino oscillations.

Bercellie, Aaron↗