SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Here, a novel all-fiber, hybrid pulse-shaping system based on the temporal stacking of discrete optical picket pulses combined with continuously shaped optical pulses provides 100-ps resolution with the high dynamic range and flexibility required for laser fusion.
Here, this paper describes the fabrication, modeling, and dynamic testing of laser powder bed fusion stainless steel walls with captured powder cores. The purpose of the study is to determine the increased structural damping, or energy dissipation, and mode shape modification caused by the inclusion of the unmelted powder core within the solid walls. It is shown experimentally that the damping increases with larger powder core width and that the damping addition is mode dependent. Damping increases over the solid wall values by factors of 2.9–225 are reported depending on the mode number and core width. It is also seen that the mode shapes are distorted relative to the solid wall results as the core width is increased and wall thickness is decreased. Comparisons with finite element models confirm this trend.
We use molecular dynamics simulations to characterize the tensile deformation and failure of shape memory alloy-bulk metallic glass composites (BMGCs). As the failure in BMGCs shifts from the MG matrix to the second phase different strategies are required to further improve their mechanical properties. Results show that a staggered brick BMGC displays enhanced ductility with mild strength loss following a homogeneously distributed plasticity. This demonstrates that judiciously designed BMGCs can effectively synergize the mechanical properties of metallic glasses and shape memory alloys by effectively distributing stress and preventing the generation of critical shear bands and premature failure while preserving strength.
Bisphenol A-based epoxies are much used in a wide range of composite and coating applications due to their excellent thermomechanical properties. However, their 3D printability remains a challenge with most reported materials suffering from high brittleness and low toughness. In this work, we have described especially modified epoxy resins that enable 3D printing with both fast and slow curing rates. These materials exhibit greatly enhanced toughness, tunable thermomechanical properties, and excellent shape memory behavior. Two different printing systems, including a two-part static mixing printhead and a single extrusion printhead, were developed for fast- and slow-curing epoxies, respectively. The rheology of inks in both systems has been modified into printable thixotropic fluids with the aid of silica nanoparticles and other additives. Epoxide-functionalized telechelic polybutadiene was added into the resins, which are then introduced inside the epoxy network after cross-linking. The addition of polybutadiene rubber significantly improves the toughness (over 135%), fracture strain (over 200%), and shape memory behavior. By adding different amounts of the rubber telechelic, thermomechanical properties, including modulus, elongation, and Tg of epoxy, can be well controlled in a wide range to satisfy different applications.
Abstract Integration of transient and steady-state divertor heat fluxes control with a high-performance core is necessary for future fusion reactors. In recent DIII-D high- β p experiments, divertor detachment and simultaneous edge localized mode (ELM) suppression are demonstrated while the plasma confinement quality is maintained high in ITER-similar shape. By optimizing the neon injection in high- β p scenario with ITER-similar shape, deep detachment and ELM suppression are achieved with a high-performance core ( β N ∼ 2.8, β p ∼ 2.3) at q 95 ∼ 7.5. Partial divertor detachment and suppression of large ELMs are achieved at q 95 ∼ 6. The stability analyses suggest that with low neon injection, the density pedestal becomes higher and steeper and the T i profile also increases, therefore the increased edge pressure and higher current density destabilize the Peeling-Ballooning mode (PBM), which would lead to a large ELM collapse. With strong neon gas puffing, the significantly reduced pedestal pressure and current density, due to the degraded T e pedestal, lead to the stabilization of PBM and ELMs are suppressed. For both cases, the coupling between the large radius internal transport barrier (ITB) and edge pedestal is the key reason for maintaining high global performance. The formation of large radius ITB compensates for pedestal degradation. Such results could provide an attractive scenario to well control the transient and steady-state heat flux onto the divertor plates while maintaining good plasma performance, which is an important step toward the steady-state operation of future fusion reactors.
Wind turbine blade design is a highly multidisciplinary process that involves aerodynamics, structures, controls, manufacturing, costs, and other considerations. More efficient blade designs can be found by controlling the airfoil cross-sectional shapes simultaneously with the bulk blade twist and chord distributions. Prior work has focused on incorporating panel-based aerodynamic solvers with a blade design framework to allow for airfoil shape control within the design loop in a tractable manner. Including higher fidelity aerodynamic solvers, such as computational fluid dynamics, makes the design problem computationally intractable. In this work, we couple an invertible neural network trained on high-fidelity airfoil aerodynamic data to a turbine design framework to enable the design of airfoil cross sections within a larger blade design problem. We detail the methodology of this coupled framework and showcase its efficacy by aerostructurally redesigning the IEA 15-MW reference wind turbine blade. The coupled approach reduces the cost of energy by 0.9% compared to a more conventional design approach. This work enables the inclusion of high-fidelity aerodynamic data earlier in the design process, reducing cycle time and increasing certainty in the performance of the optimal design.
Abstract Three different metamaterial structures were fabricated using stereolithography 3D printing and a shape recovering material. Mechanical properties and recovery efficiency were assessed after compression testing. All three structures exhibited similar initial specific compressive moduli, while the highest specific toughness was observed for the stretch-dominated structure. The three metamaterial structures were re-tested after shape recovery. Significant strengthening was observed for all structures, with the bend-stretch-dominated structure strengthening to the highest degree. This strengthening phenomenon was characterized as strain hardening. It was found that the strengthening is highly geometry dependent. The geometry with stretch-dominated behavior exhibited the highest mechanical properties after a second test was performed. Improvements in specific toughness of up to 67% were observed after the second compressive test.
Here, we consider the problem of controlling the frequency of low-inertia power systems via inverter-based resources (IBRs) that are weakly connected to the grid. We propose a novel grid-forming control strategy, the so-called frequency shaping control, that aims to shape the frequency response of synchronous generators (SGs) to load perturbations so as to efficiently arrest sudden frequency drops. Our solution relaxes several existing assumptions in the literature and is able to navigate trade-offs between peak power requirements and maximum frequency deviations. Finally, we analyze the robustness to imperfect knowledge of network parameters, while particularly highlighting the importance of accurate estimation of these parameters.
G2Aero is a Python package for the design and deformation of discrete planar curves and tubular surfaces using a geometric data-driven approach. G2Aero utilizes a topology of product manifolds: the Grassmannian, $\mathcal{G}$($\mathcal{n}$, 2) - the set of 2-dimensional subspaces in $\mathbb{R}$ $\mathcal{n}$ - and the symmetric positive-definite (SPD) manifold, $\mathcal{S}^{2}_{++}$ - the set of 2x2 SPD matrices. The package provides a novel framework for representing separable deformations to shapes, which consist of stretching, scaling, rotating, and translating - also known as affine deformations - and a set of complementary deformations - which we refer to as undulation-type deformations. We focus on airfoil and blade design applications to emphasize the utility of the methods in an environment where the separation of affine and undulation-type deformations is critical. Notable functionalities of the framework for blade design include: 1) generating novel 2D (airfoil) shapes informed by a database of physically relevant airfoils, 2) building 3D blades by interpolating sequences of 2D airfoil cross-sections, and 3) generating blades with consistent perturbations along the blade span. We discuss the framework and provide examples in the context of wind energy applications, specifically wind turbine blade design. Figure 1 shows the wire frame obtained by interpolating airfoils defining the IEA 15-MW wind turbine blade and applying affine transformations corresponding to twist, chordal scaling, and bending. This, and all other figures in the paper, can be reproduced following examples and referencing supporting documentation provided in the G2Aero package.
Shear Assisted Processing and Extrusion (ShAPE) was developed to manufacture non-circular multicell profiles from secondary aluminum. This was accomplished by integrating a porthole die approach within the rotating ShAPE process. Complexity of the profile geometry was deliberately advanced over the course of the project from round to square, to asymmetric trapezoidal, to two-cell asymmetric trapezoidal. Aluminum alloy 6063 in the form of briquettes (compacted shreddings and engineered machining chips) and castings from pre-consumer industrial scrap were utilized as the feedstock. Tensile properties were shown to exceed the ASTM minimum standard and ASM typical values with the best results reaching yield strength = 247 ± 10 MPa, ultimate tensile strength = 271 ± 10 MPa, and uniform elongation = 16.5 ± 2.4%. These values were achieved for porthole extrusion using unhomogenized castings made from 100% aluminum 6063 industrial scrap. The ability to extrude unhomogenized billet was made possible by in situ conversion of plate-like β-type Fe-rich intermetallics to more extrudable needle-like α-type which is not possible with conventional extrusion. By eliminating the need to dilute iron with primary aluminum during the recycling process, savings of >90% on lifecycle carbon footprint and >50% on embedded energy could ultimately result in lower cost, more environmentally friendly, automotive components.
Through this DOE funded 3.5-year research project, feasibility of fabricating supercritical carbon dioxide (sCO2) turbine components by powder metallurgy (PM) based near-net-shape (NNS) hot isostatic pressing (HIP) was demonstrated in a turbine nozzle ring, a turbine casing with Haynes 282 powder, and a bimetallic pipe with Haynes 282 and SS415 powder. As-HIP microstructure of various powders and HIP processing conditions was studied to downselect a condition for the prototype components. Tensile strength and low cycle fatigue (LCF) capability of PM HIP 282 was found to be superior to cast 282, despite a debit in creep stress capability that could be mitigated by component design modification. Near-Net-shape with minimal post machining was achieved by modeling the non-uniform shrinkage during HIP cycle and designing the HIP tooling to meet dimensional targets. The prototypes of turbine nozzle ring and bimetallic pipe were successful in achieving overall dimension, microstructure, and properties, despite dimensional tolerance affected by chemical milling rate. The prototype of a 1700lbs turbine casing was partially successful in achieving dimension, microstructure in as-HIP state, and providing consistent mechanical properties, however, cracking issue during post heat treatment required further investigation. The estimated manufacturing cost using NNS HIP was a ~50% reduction compared to forging with extensive machining, which translated into ~$100/kWe CAPEX cost reduction for concentrated solar power (CSP) power block.
The overarching objective of this project is to convert metal scraps, such as aluminum, titanium, and other alloys provided by the industry, into extruded tubing, wires, and rods. Upcycling of scrap will be accomplished using Shear Assisted Processing and Extrusion (ShAPE). This approach is a new solution for recycling. The specific aims of this project are as follows: 1. Receive metal scrap under a Material Transfer Agreement (MTA), in the form of billets, from select industry partners that meet the following requirements: outer diameter of 1.245 inches (+/-0.003 inches), inner diameter drilled with a 0.404-inch drill bit, and a length of 4.0 inches (+/-0.01 inches). The billet must be cast or compacted to greater than 98% density. If the industry partner does not have the capabilities to prepare the billets, PNNL can make introductions to third-party entities as needed. Industry partners will also provide a composition analysis as weight percent. 2. Extrude metal scrap via the ShAPE process at PNNL. 3. Evaluate and benchmark the extrudate material properties per the ASTM B557-15 – Testing Tubulars Standard or similar wire and rod standards. 4. Characterize the extrudate microstructure for any of the following: grain size, second phase composition, and texture. Additional testing may include corrosion per the ASTM B117 standard and electro-potential. 5. Deliver specimens to industry partners under an MTA for additional third-party evaluations. Industry partners will, in return, provide a non-proprietary report on any testing, including testing per the ASTM B557-15, ASTM B117, and other industry standards. 6. PNNL will develop data and insights to support intellectual property capture, a published non-proprietary technical report, research collaborations, and commercialization opportunities.
The use of porous adsorbents for the densification of H 2 under relatively mild pressures and temperatures has been long pursued through various avenues of synthetic organic frameworks, namely metal–organic frameworks. However, the overwhelming majority of these materials are macroscopically rigid, exhibiting adsorption–desorption profiles that require appreciable energetic input for their full payload capacity to be stored and subsequently delivered. This reduced “deliverable” capacity is a core inefficiency in the use of porous adsorbents for H 2 densification. Our core mission is to determine a material-based strategy that fundamentally alters the adsorption¬–desorption profile in a manner that obviates these deleterious energetic requirements. Towards this, we have focused on metal–organic frameworks that exhibit “cooperative flexibility”, wherein the material undergoes reversible macroscopic phase changes in response to changes to external temperature and/or adsorbate pressure (i.e., concentration). Where these reversible switches occur between states of disparate enough accessible porosity, cooperatively flexible frameworks can exhibit “step-shaped” adsorption–desorption profiles that enable use of the delivery gaseous payload without the aforementioned additional energy requirements. However, before our work, such the observation of this phenomenon with very weakly adsorbing H 2 had not been observed with the necessary profile and P/T conditions desired for H 2 storage and delivery. During this project we have leveraged a deep understanding of the phase change in family of cooperatively flexible metal–organic frameworks to systematically alter their adsorption–desorption profiles to achieve step-shaped adsorption and desorption of H 2 in a precise P/T regime that enables a high deliverable capacity. Specifically, the thermodynamics of the adsorption/desorption induced phase changes in the baseline framework CdIF-13 (sod–Cd(benzimidazolate) 2 ) were tuned using the mixed-linker, or multivariate, approach to framework derivatization. Follow this, we have pursued a similar approach to tuning the adsorption–desorption profile of a second framework family, MIL-53(Al), which contains only Al(III) and theoretically exhibits a much higher deliverable capacity. In total, our work demonstrates that by first understanding the structural consequences of phase changes in these materials, their behavior can be systematically altered through ligand substitutions, tuning the pressure and temperature conditions at which H 2 is adsorbed and desorbed. Thus, enabling high deliverable capacities of H 2 with minimized energetic requirements.
Soft magnetic composites (SMCs) offer a promising alternative to electrical steels and soft ferrites in high performance motors and power electronics. They are ideal for incorporation into passive electronic components such as inductors and transformers, which require a non-permanent magnetic core to rapidly switch magnetization. As a result, there is a need for materials with the right combination of low coercivity, low magnetic remanence, high relative permeability, and high saturation magnetization to achieve these goals. Iron nitride is an attractive soft magnetic material for incorporation into an amine/epoxy resin matrix. This permits the synthesis of net-shaped SMCs using a “bottom-up” approach for overcoming the limitations of current state-of-the-art SMCs made via conventional powder metal processing techniques. In this work we present the fabrication of various net-shaped, iron nitride-based SMCs using two different amine/epoxy resin systems and their magnetic characterization. The maximum volume loading of iron nitride reached was ~77% via hot pressing, which produced SMCs with a saturation magnetic polarization (J s ) of ~0.9 T, roughly 2–3 times the J s of soft ferrites.
We consider the problem of controlling the frequency of low-inertia power systems via inverter-based resources (IBRs) that are weakly connected to the grid. We propose a novel grid-forming control strategy, the so-called frequency shaping control, that aims to shape the frequency response of synchronous generators (SGs) to load perturbations so as to efficiently arrest sudden frequency drops. Our solution relaxes several existing assumptions in the literature and is able to navigate trade-offs between peak power requirements and maximum frequency deviations. Finally, we analyze the robustness to imperfect knowledge of network parameters, while particularly highlighting the importance of accurate estimation of these parameters.
We consider the problem of controlling the frequency response of weakly-coupled multi-machine multi-inverter low-inertia power systems via grid-forming inverter-based resources (IBRs). In contrast to existing methods, our approach relies on dividing the larger system into multiple strongly-coupled subsystems, without ignoring either the underlying network or approximating the subsystem response as an aggregate harmonic mean model. Rather, through a structured clustering and recursive dynamic shaping approach, the frequency response of the overall system to load perturbations is shaped appropriately. We demonstrate the proposed approach for a three-node triangular configuration and a small-scale radial network. Furthermore, for small-scale radial microgrids, we demonstrate the ability of IBRs to tune the effective transfer functions of synchronous machines. This enables us to relax the uniform turbine time-constant assumptions and widen the scope of existing synchronization results for proportionally heterogeneous machines.
Abstract High power conversion efficiency (PCE), long‐term stability, and mechanical robustness are prerequisites for the commercial applications of organic solar cells (OSCs). In this study, a new star‐shaped trimer acceptor (TYT‐S) is developed and high‐performance OSCs with a PCE of 19.0%, high photo‐stability (t 80% lifetime = 2600 h under 1‐sun illumination), and mechanical robustness with a crack‐onset strain (COS) of 21.6% are achieved. The isotropic molecular structure of TYT‐S affords efficient multi‐directional charge transport and high electron mobility. Furthermore, its amorphous structure prevents the formation of brittle crystal‐to‐crystal interfaces, significantly enhancing the mechanical properties of the OSC. As a result, the TYT‐S‐based OSCs demonstrate a significantly higher PCE (19.0%) and stretchability (COS = 21.6%) than the linear‐shaped trimer acceptor (TYT‐L)‐based OSCs (PCE = 17.5% and COS = 6.4%) and the small‐molecule acceptor (MYT)‐based OSCs (PCE = 16.5% and COS = 1.3%). In addition, the increased molecular size of TYT‐S, relative to that of MYT and dimer (DYT), suppresses the diffusion kinetics of the acceptor molecules, substantially improving the photostability of the OSCs. Finally, to effectively demonstrate the potential of TYT‐S, intrinsically stretchable (IS)‐OSCs are constructed. The TYT‐S‐based IS‐OSCs exhibit high device stretchability (strain at PCE 80% = 31%) and PCE of 14.4%.
For soft bodies, surface deformation and pressure provide proprioceptive and exteroceptive information, including body configuration, body compliance, and external forces. We develop a sheet sensor with a fully soft sensing surface that provides surface shape reconstruction using optical waveguide arrays. The waveguides are fabricated to achieve a tunable linear response to bi‐directional bending curvature, and the waveguide arrays are configured to differentiate between ambiguous shapes. We characterize the waveguide performance, relating curvature sensitivity to the core's surface roughness. Synergy of waveguide responses reduces the number of sensing elements required and achieves damage resilience. Using waveguide sensitivity to pressure, we also demonstrate feasibility for exteroception. We demonstrate the multifunctional sensing capability by wrapping the sheet around an upper arm, showcasing joint motion and external force sensing. Integrated into or applied onto surfaces of robotic or living systems, this design can be implemented in applications such as virtual reality, teleoperation, physical therapy, and soft robotics.