Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “scaled testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Ice-Accretion Scaling Using Water-Film Thickness Parameters

Studies were performed at INTA in Spain to determine water-film thickness on a stagnation-point probe inserted in a simulated cloud. The measurements were correlated with non-dimensional parameters describing the flow and the cloud conditions. Icing scaling tests in the NASA Glenn Icing Research Tunnel were then conducted using the Ruff scaling method with the scale velocity found by matching scale and reference values of either the INTA non-dimensional water-film thickness or a Weber number based on that film thickness. For comparison, tests were also performed using the constant drop-size Weber number and the average-velocity methods. The reference and scale models were both aluminum, 61-cm-span, NACA 0012 airfoil sections at 0 deg. AOA. The reference had a 53-cm-chord and the scale, 27 cm (1/2 size). Both models were mounted vertically in the center of the IRT test section. Tests covered a freezing fraction range of 0.28 to 1.0. Rime ice (n = 1.0) tests showed the consistency of the IRT calibration over a range of velocities. At a freezing fraction of 0.76, there was no significant difference in the scale ice shapes produced by the different methods. For freezing fractions of 0.40, 0.52 and 0.61, somewhat better agreement with the reference horn angles was typically achieved with the average-velocity and constant-film thickness methods than when either of the two Weber numbers was matched to the reference value. At a freezing fraction of 0.28, the four methods were judged equal in providing simulations of the reference shape.

Anderson, David N.↗
NASA NTRS2011

A Comparative Analysis of Two Full-Scale MD-500 Helicopter Crash Tests

Two full scale crash tests were conducted on a small MD-500 helicopter at NASA Langley Research Center fs Landing and Impact Research Facility. One of the objectives of this test series was to compare airframe impact response and occupant injury data between a test which outfitted the airframe with an external composite passive energy absorbing honeycomb and a test which had no energy absorbing features. In both tests, the nominal impact velocity conditions were 7.92 m/sec (26 ft/sec) vertical and 12.2 m/sec (40 ft/sec) horizontal, and the test article weighed approximately 1315 kg (2900 lbs). Airframe instrumentation included accelerometers and strain gages. Four Anthropomorphic Test Devices were also onboard; three of which were standard Hybrid II and III, while the fourth was a specialized torso. The test which contained the energy absorbing honeycomb showed vertical impact acceleration loads of approximately 15 g, low risk for occupant injury probability, and minimal airframe damage. These results were contrasted with the test conducted without the energy absorbing honeycomb. The test results showed airframe accelerations of approximately 40 g in the vertical direction, high risk for injury probability in the occupants, and substantial airframe damage.

Littell, Justin D.↗
NASA NTRS1925

Simplified propeller design for low-powered airplanes

The object of this report is to furnish the designer and builder of small airplanes a simple system for designing the propeller and making the drawing. An empirical design method is used, based on tests of model propellers in a wind tunnel and full scale tests of propellers in flight.

Weick, Fred E↗
NASA NTRS2010

Testing and Results of Vacuum Swing Adsorption Units for Spacesuit Carbon Dioxide and Humidity Control

A principal concern for extravehicular activity (EVA) space suits is the capability to control carbon dioxide (CO2) and humidity (H2O) for the crewmember. The release of CO2 in a confined or unventilated area is dangerous for human health and leads to asphyxiation; therefore, CO2 and H2O become leading factors in the design and development of the spacesuit. An amine-based CO2 and H2O vapor sorbent for use in pressure-swing re-generable beds has been developed by Hamilton Sundstrand. The application of solid-amine materials with vacuum swing adsorption technology has shown the capacity to concurrently manage CO2 and H2O levels through a fully regenerative cycle eliminating mission constraints imposed with non-regenerative technologies. Two prototype solid amine-based systems, known as rapid cycle amine (RCA), were designed to continuously remove CO2 and H2O vapor from a flowing ventilation stream through the use of a two-bed amine based, vacuum-swing adsorption system. The Engineering and Science Contract Group (ESCG) RCA is the first RCA unit implementing radial flow paths, whereas the Hamilton Sundstrand RCA was designed with linear flow paths. Testing was performed in a sea-level pressure environment and a reduced-pressure environment with simulated human metabolic loads in a closed-loop configuration. This paper presents the experimental results of laboratory testing for a full-size and a sub-scale test article. The testing described here characterized and evaluated the performance of each RCA unit at the required Portable Life Support Subsystem (PLSS) operating conditions. The test points simulated a range of crewmember metabolic rates. The experimental results demonstrate the ability of each RCA unit to sufficiently remove CO2 and H2O from a closed loop ambient or subambient atmosphere.

McMillin, Summer↗
NASA NTRS2011

Testing and Results of Vacuum Swing Adsorption Units for Spacesuit Carbon Dioxide and Humidity Control

A principal concern for extravehicular activity (EVA) spacesuits is the capability to control carbon dioxide (CO2) and humidity (H2O) for the crewmember. The release of CO2 in a confined or unventilated area is dangerous for human health and leads to asphyxiation; therefore, CO2 and H2O control become leading factors in the design and development of the spacesuit. An amine-based CO2 and H2O vapor sorbent for use in pressure-swing regenerable beds has been developed by Hamilton Sundstrand. The application of solidamine materials with vacuum swing adsorption technology has shown the capacity to concurrently manage CO2 and H2O levels through a fully regenerative cycle eliminating mission constraints imposed with nonregenerative technologies. Two prototype solid amine-based systems, known as rapid cycle amine (RCA), were designed to continuously remove CO2 and H2O vapor from a flowing ventilation stream through the use of a two-bed amine based, vacuum-swing adsorption system. The Engineering and Science Contract Group (ESCG) RCA implements radial flow paths, whereas the Hamilton Sundstrand RCA was designed with linear flow paths. Testing was performed in a sea-level pressure environment and a reduced-pressure environment with simulated human metabolic loads in a closed-loop configuration. This paper presents the experimental results of laboratory testing for a full-size and a sub-scale test article. The testing described here characterized and evaluated the performance of each RCA unit at the required Portable Life Support Subsystem (PLSS) operating conditions. The test points simulated a range of crewmember metabolic rates. The experimental results demonstrated the ability of each RCA unit to sufficiently remove CO2 and H2O from a closed loop ambient or sub-ambient atmosphere.

McMillin, Summer D.↗
NASA NTRS2008

An Experimental Investigation of the Dynamics of the MSL Rover Landing Event

A developmental test program was conducted for the touchdown event of the Mars Science Laboratory rover. The test hardware consisted of a full-size 3/8th mass scaled test rover, a descent stage mass mock-up, and a Vectran triple-bridle system over 6 meters in length. More than eighty landing tests were performed on terrains of various types, including level rigid surfaces, level and sloped sand surfaces, and level and sloped surfaces with rocks. Landing velocities ranged between 0.4 m/s and 1.4 m/s. A computational model of the landings was developed using the ADAMS analysis program, and validation of this model has been performed through test-analysis comparisons.

Planetary Landing↗
NASA NTRSDate not supplied

3D Woven Composite End Ring Structure: Design Development and Verification Testing

The National Aeronautics and Space Administration (NASA) Space Technology and Mission Directorate (STMD) is advancing composite technologies for exploration missions. The Composite Technology for Exploration (CTE) project goal is to advance lightweight joint concepts for Space Launch System (SLS) class structures. To this end CTE is developing and demonstrating a 3D woven carbon /epoxy composite joint design co-bonded in a circumferential end ring configuration, applied to a SLS sized conceptual payload attachment structure. This joint is a lightweight alternative to heavy and costly metallic joints. The 3D woven joint development advances lightweight joint technologies through material and structural design, material and joint analyses, and fabrication, as well as demonstration through building block testing. Prior limited building block tests are mentioned. In this paper, new sub-element-scale test results are described that demonstrate the structural capability well beyond design limit load. Then, results for a sub-component test article with a 889 mm joint subjected to combined loads are presented.

Kenneth N Segal↗
NASA NTRS2016

Terrestrial Testing of the CapiBRIC, a Microgravity Optimized Brine Processor

Utilizing geometry based static phase separation exhibited in the radial vaned capillary drying tray, a system was conceived to recover water from brine. This technology has been named the Capillary BRIC; abbreviated CapiBRIC. The CapiBRIC utilizes a capillary drying tray within a drying chamber. Water is recovered from clean water vapor evaporating from the free surface leaving waste brine solids behind. A novel approach of optimizing the containment geometry to support passive capillary flow and static phase separation provides the opportunity for a low power system that is not as susceptible to fouling as membranes or other technologies employing physical barriers across the free brine surface to achieve phase separation in microgravity. Having been optimized for operation in microgravity, full-scale testing of the CapiBRIC as designed cannot be performed on the ground as the force of gravity would dominate over the capillary forces. However, subscale units relevant to full-scale design were used to characterize fill rates, containment stability, and interaction with a variable volume reservoir in the PSU Dryden Drop Tower (DDT) facility. PSU also using tested units scaled such that capillary forces dominated in a 1-g environment to characterize evaporation from a free-surface in 1-g upward, sideways and downward orientations. In order to augment the subscale testing performed by PSU, a full scale 1-g analogue of the CapiBRIC drying unit was initiated to help validate performance predictions regarding expected water recovery ratio, estimated processing time, and interface definitions for inlets, outlets, and internal processes, including vent gas composition. This paper describes the design, development and test of the terrestrial CapiBRIC prototypes.

Sargusingh, Miriam J.↗
NASA NTRS1994

Large Scale Scramjet Propulsion Testing In The Mach 8 and 16 Regime At NASA Ames Research Center

The objective of this paper is to describe the affordable, large scale scramJet test capability for flight Mach numbers between 8 and 16 which has been developed at the NASA Ames Research Center. Details of the Direct Connect Arc Facility DCAF, which can produce combustor test conditions with fuel-on testing for 10 seconds at conditions representative of Mach 8 - 12 flight, are presented and typical test results are described. Likewise, a description of the full scale combustor test capability of the 16 inch shock tunnel is outlined. This facility is characterized by long run times (> 5 milliseconds) for an impulse facility, and it can provide conditions representative of flight conditions from Mach 12 - 16. Typical test results for this shock tunnel are discussed as well. Future upgrades to both facilities are outlined and new uses for their capabilities are discussed.

Arnold, James O.↗
NASA NTRS2019

A Single Stage to Orbit Design for a Hybrid Mars Ascent

A Single Stage to Orbit (SSTO) hybrid propulsion system has been previously studied as an option for a conceptual Mars Ascent Vehicle (MAV). The hybrid motor uses a wax-based fuel developed specifically for this application, so it can take advantage of a single port design. The oxidizer is Mixed Oxides of Nitrogen (MON-25). Higher Nitric Oxide concentrations have been discussed in the past, however, the lower temperature capability is no longer needed. The MAV Payload Assembly (MPA), which would house the Orbiting Sample (OS) has changed substantially from previous iterations and has become more compact. Benefits of the hybrid option include its predicted low temperature behavior, high performance and ability to restart (enabling the SSTO). However, the hybrid technology remained at a relatively low Technology Readiness Level (TRL). In an attempt to increase the TRL, a technology development program has been underway for the past four years. The results of the technology development program are now being incorporated to an updated concept for a hybrid Mars Ascent Vehicle, with the eventual goal of informing a hybrid propulsion design that closes under the guidelines currently envisioned for a potential Mars Sample Return campaign. This paper focuses on the hybrid propulsion system design and the preliminary results from the first part of the FY19 technology development program (October 2018 to July 2019) and includes some results from a Preliminary Architecture Assessment (PAA) study. In the PAA, experts from all relevant subsystems (propulsion, avionics, GN&C, structures, thermal, etc.) are brought together to determine an updated vehicle design. The PAA is being run out of Marshall Space Flight Center (MSFC) in coordination with the Mars Sample Return study lead by the Jet Propulsion Laboratory (JPL). Currently, it is thought that the Mars Ascent Vehicle would be housed in a Sample Retrieval Lander (SRL), along with a fetch rover. The SRL would be responsible for several crucial functions on the MAV including heating, erection and providing the ignition signal. This paper will also outline the future testing and path forward through the rest of the fiscal year. This includes full scale testing at Whittinghill Aerospace, hypergolic additive testing at Purdue, evaluation of adding hypergolic additives to a full-scale grain. A hybrid fuel formulation has been updated with a reduced regression rate, which again was developed by Space Propulsion Group. This design will be used to determine the benefits of a hybrid versus solid propulsion system for a MAV, as they fit into the larger vision for a potential Mars Sample Return campaign.

Story, George↗
NASA NTRS1992

Experimental investigation of an ejector-powered free-jet facility

NASA Lewis Research Center's (LeRC) newly developed Nozzle Acoustic Test Rig (NATR) is a large free-jet test facility powered by an ejector system. In order to assess the pumping performance of this ejector concept and determine its sensitivity to various design parameters, a 1/5-scale model of the NATR was built and tested prior to the operation of the actual facility. This paper discusses the results of the 1/5-scale model tests and compares them with the findings from the full-scale tests.

Long, Mary JO↗
NASA NTRS1977

Tenth-scale powered model test of a tilt-nacelle V/STOL airplane

Wind tunnel and ground static tests of a tenth scale powered model of a lift/cruise fan airplane have been conducted to define its low speed performances and handling qualities. The model was powered by three 5.5-in diameter turbopowered simulators; one located in the forebody while the remaining two were installed in tilting nacelles mounted on the aft body. Results are presented for static hover tests in ground effects with the model configured for VTOL operations and at forward speeds with the model configured for loiter, short takeoff, and VTOL operations.

Omar, M. E.↗
NASA NTRS2005

Aeroelastic Deformation: Adaptation of Wind Tunnel Measurement Concepts to Full-Scale Vehicle Flight Testing

The adaptation of a proven wind tunnel test technique, known as Videogrammetry, to flight testing of full-scale vehicles is presented. A description is presented of the technique used at NASA's Dryden Flight Research Center for the measurement of the change in wing twist and deflection of an F/A-18 research aircraft as a function of both time and aerodynamic load. Requirements for in-flight measurements are compared and contrasted with those for wind tunnel testing. The methodology for the flight-testing technique and differences compared to wind tunnel testing are given. Measurement and operational comparisons to an older in-flight system known as the Flight Deflection Measurement System (FDMS) are presented.

Burner, Alpheus W.↗
NASA NTRS2005

Aeroelastic Deformation: Adaptation of Wind Tunnel Measurement Concepts to Full-Scale Vehicle Flight Testing

The adaptation of a proven wind tunnel test technique, known as Videogrammetry, to flight testing of full-scale vehicles is presented. A description is presented of the technique used at NASA's Dryden Flight Research Center for the measurement of the change in wing twist and deflection of an F/A-18 research aircraft as a function of both time and aerodynamic load. Requirements for in-flight measurements are compared and contrasted with those for wind tunnel testing. The methodology for the flight-testing technique and differences compared to wind tunnel testing are given. Measurement and operational comparisons to an older in-flight system known as the Flight Deflection Measurement System (FDMS) are presented.

Burner, Alpheus W.↗
NASA NTRSDate not supplied

NASA’s Orion Crew Module Seakeeping Simulation and Test Comparisons in Ocean Wave Environments

The NASA Orion Crew Module (CM) post-landing seakeeping and uprighting capabilities are being evaluated across a variety of ocean wave conditions. This paper provides an overview of quarter-scale and full-scale test data and how it compares with the CM seakeeping dynamic simulation results evaluated using Wave Energy Convertor Simulator (WEC-Sim).This includes a discussion of the status of the dynamic modeling effort, correlation of model inputs with the wave field from the test, and a comparison of the results against the physical test data with emphasis on the full-scale results. Analysis in the frequency domain showed similar response characteristics between the model and the test and shows energy peaks corresponding to both the natural response and the forced response due to the wave environment. Time domain comparisons showed that the linear WEC-Sim model under predicted the amplitude of the pitch and roll motion of the test article, with improved matching for smaller, longer crested waves. An attempt was made to correlate the pitch/roll response to incident wave slope to account for a possible delay in the BTA’s response. The results did not show a strong relationship in the response characteristics to incident wave slope, but better correlation was seen by comparing responses in the frequency domain. Evaluation of the simulation’s ability to match test results aided in understanding the current fidelity of the CM model in WEC-Sim and identifying areas for model improvement

Abigail Lockard↗
NASA NTRS2009

Status of the Combined Cycle Engine Rig

Status for the past year is provided of the turbine-based Combined-Cycle Engine (CCE) Rig for the hypersonic project. As part of the first stage propulsion of a two-stage-to-orbit vehicle concept, this engine rig is designed with a common inlet that supplies flow to a turbine engine and a dual-mode ramjet / scramjet engine in an over/under configuration. At Mach 4 the inlet has variable geometry to switch the airflow from the turbine to the ramjet / scramjet engine. This process is known as inlet mode-transition. In addition to investigating inlet aspects of mode transition, the rig will allow testing of turbine and scramjet systems later in the test series. Fully closing the splitter cowl "cocoons" the turbine engine and increases airflow to the scramjet duct. The CCE Rig will be a testbed to investigate integrated propulsion system and controls technology objectives. Four phases of testing are planned to 1) characterize the dual inlet database, 2) collect inlet dynamics using system identification techniques, 3) implement an inlet control to demonstrate mode-transition scenarios and 4) demonstrate integrated inlet/turbine engine operation through mode-transition. Status of the test planning and preparation activities is summarized with background on the inlet design and small-scale testing, analytical CFD predictions and some details of the large-scale hardware. The final stages of fabrication are underway.

Saunders, Dave↗
NASA NTRS1974

Aerodynamics of jet flap and rotating cylinder flap STOL concepts

The aerodynamic effectiveness of various propulsive lift concepts to provide for the low speed performance and control required for short takeoff and landing aircraft is discussed. The importance of the interrelationship between the propulsion system and aerodynamic components of the aircraft is stressed. The relative effectiveness of different lift concepts was evaluated through static and wind tunnel tests of various aerodynamic models and propulsion components, simulations of aircraft, and in some cases, flight testing of research aircraft incorporating the concepts under study. Results of large scale tests of lift augmentation devices are presented. The results of flight tests of STOL research aircraft with augmented jet flaps and rotating cylinder flaps are presented to show the steeper approach flight paths at low forward speeds.

Cook, W. L.↗