Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

System technology analysis of aeroassisted orbital transfer vehicles. Moderate lift/drag (0.75-1.5). Volume 1A, part 1: Executive summary, phase 1

Activities and significant results of Phase 1 of a study to access aeroassisted orbit transfer vehicle (AOTV) system technology are summarized. Broad concept evaluations were performed and the technology requirements and sensitivities for ground based AOTV's over a range of vehicle hypersonic lift/drag (L/D) from 0.75 to 1.5 were systematically identified and assessed. The four major task areas included systems analysis, system/subsystem trades, technology payoff assessment and plan, and cost analysis. Findings indicate that substantial performance improvements and hence cost benefit can be obtained by developing enhanced technologies such as: (1) low thrust advanced expander LOX-hydrogen engines with specific impulse of 480 to 490 sec; (2) reducing the external thermal protection system weight and increasing the maximum allowable bond/structure temperature; and (3) reducing the structural shell weight by improving the quality of the design allowable data, or use of advanced structural materials. Results also show that use of mid L/D AOTV's provide significant aerodynamic plane change capability and control authority over trajectory dispersions and off-nominal atmospheres.

Source record↗
NASA NTRS1981

Orbital transfer vehicle - An overview

A summary is given of the concept definition phase of NASA's Orbital Transfer Vehicle (OTV) program. The mission requirements are threefold: (1) the ability to deliver payloads well beyond the capability of any current system at low acceleration levels, (2) the extension of the cost effectiveness from reusability and operational flexibility provided by the Shuttle at LEO to the geosynchronous altitude, and (3) the provision of the round trip capability needed to service and maintain this expanded and more valuable resource at GEO. The initial Shuttle-matched, reusable OTV is shown to be cost effective with low development cost, relatively short development period and high projected reliability. The performance enhancement provided by aero-assist is discussed, which will enable the difficult round trip to be flown in a single Shuttle launch. Two methods of reducing vehicle velocity are available: (1) aeromaneuvering, which uses vehicle lift to climb or descend and thereby correct for density variations, and (2) aerobraking which varies vehicle drag directly to correct for density.

Caluori, V. A.↗
NASA NTRS1985

Results of a M = 5.3 heat transfer test of the integrated vehicle using phase-change paint techniques on the 0.0175-scale model 56-OTS in the NASA/Ames Research Center 3.5-foot hypersonic wind tunnel

An experimental investigation was performed in the NASA/Ames Research Center 3.5-foot Hypersonic Wind Tunnel to obtain supersonic heat-distribution data in areas between the orbiter and external tank using phase-change paint techniques. The tests used Novamide SSV Model 56-OTS in the first and second-stage ascent configurations. Data were obtained at a nominal Mach number of 5.3 and a Reynolds number per foot of 5 x 10 to the 6th power with angles of attack of 0 deg, +/- 5 deg, and sideslip angles of 0 deg and +/- 5 deg.

Marroquin, J.↗
NASA NTRS2018

Advancing Torpor Inducing Transfer Habitats for Human Stasis to Mars: II - Phase

SpaceWorks Enterprises, Inc. (SEI) has conducted an evaluation of an advanced habitat system designed to transportcrews between the Earth and Mars. This new and innovative habitat concept is capable of placing crew members ininactive, torpor states during transit phases of a deep space mission. This substantially reduces the mass and size ofthe habitat, which ultimately leads to significant reductions in the overall architecture size.Our approach for achieving this is based on extending the current and evolving medical practice of TherapeuticHypothermia (TH) - a proven and effective treatment for various traumatic injuries. TH is a medical treatment thatlowers a patient's body temperature by just 5 to 10 degrees Fahrenheit causing human metabolic rate to decreasesignificantly and the body to enter an unconscious state. This method avoids the intractable challenges often associatedwith cell metabolic cessation through cryogenic freezing and other highly speculative approaches.The initial results obtained from the research and analysis conducted in the Phase I effort warranted further study ofthis concept and technology. The specific objectives of the continued work include:1. Addressing critical medical aspects and risks for inducing torpor via Therapeutic Hypothermia and theapproach for providing nutrition and hydration for the crew during torpor. 2. Focusing on mitigation aspects and technology potential for solving key human spaceflight challenges. 3. Addressing critical engineering aspects of the design that may impact the initial performance and cost resultsobtained in Phase I. 4. Examining the broader extensibility and enabling capabilities of this concept through applicability toadditional exploration missions beyond Mars. 5. Establishing a technology development roadmap, addressing both medical and engineering aspects, thatindicate a logical and scientifically achievable path forward for maturation of this technology.

Stasis↗
NASA NTRS1996

Experimental and Analytical Study of Two-Phase Flow in Microgravity

Design of the two-phase flow systems which are anticipated to be utilized in future spacecraft thermal management systems requires a knowledge of two-phase flow and heat transfer parameters in reduced gravities. A program has been initiated by NASA to design a two-phase test loop and to perform a series of experiments to study the effect of gravity on the Critical Heat Flux (CHF) and onset of instability. The test loop is also instrumented to generate data for two-phase pressure drop. In addition to low gravity airplane trajectory testing, the experimental program consisted of a set of laboratory tests which were intended to generate data under the bounding conditions (+1 g and -1 g) in order to plan the test matrix. One set of airplane trajectory tests has been performed and several modifications to the test set-up have been identified. Preliminary test results have been used to demonstrate the applicability of the earth gravity models for prediction of the two-phase friction pressure drop.

McQuillen, John B.↗
NASA NTRS2014

Crosstalk Cancellation for a Simultaneous Phase Shifting Interferometer

A method of minimizing fringe print-through in a phase-shifting interferometer, includes the steps of: (a) determining multiple transfer functions of pixels in the phase-shifting interferometer; (b) computing a crosstalk term for each transfer function; and (c) displaying, to a user, a phase-difference map using the crosstalk terms computed in step (b). Determining a transfer function in step (a) includes measuring intensities of a reference beam and a test beam at the pixels, and measuring an optical path difference between the reference beam and the test beam at the pixels. Computing crosstalk terms in step (b) includes computing an N-dimensional vector, where N corresponds to the number of transfer functions, and the N-dimensional vector is obtained by minimizing a variance of a modulation function in phase shifted images.

Olczak, Eugene↗
NASA NTRS1984

Heat transfer and oil flow studies on a single-stage-to-orbit control-configured winged entry vehicle

Results are presented for oil flow and phase change paint heat transfer tests conducted on a 0.006 scale model of a proposed single stage to orbit control configured vehicle. The data were taken at angles of attack up to 40 deg at a free stream Mach number of 10 for Reynolds numbers based on model length of 0.5 x 10 to the 6th power, 1.0 x 10 to the 6th power and 2.0 x 10 to the 6th power. The magnitude and distribution of heating are characterized in terms of angle of attack and Reynolds number aided by an analysis of the flow data which are used to suggest the presence of various three dimensional flow structures that produce the observed heating patterns. Of particular interest are streak heating patterns that result in high localized heat transfer rates on the wing windward surface at low to moderate angles of attack. These streaks are caused by the bow-shock/wing-shock interaction and formation of the wing-shock. Embedded vorticity was found to be associated with these interactions.

Helms, V. T., III↗
NASA NTRS2000

Helium Evolution from the Transfer of Helium Saturated Propellant in Space

Helium evolution from the transfer of helium saturated propellant in space is quantified to determine its impact from creating a two-phase mixture in the transfer line. The transfer line is approximately 1/2 inch in diameter and 2400 inches in length comprised of the Fluid Interconnect System (FICS), the Orbiter Propellant Transfer System (OPTS) and the International Space Station (ISS) Propulsion Module (ISSPM). The propellant transfer rate is approximately two to three gallons per minute, and the supply tank pressure is maintained at approximately 250 psig.

Nguyen, Bich N.↗
NASA NTRS2023

Experimental Investigation of Flow Orientation Effects on Cryogenic Flow Boiling

Cryogenic flow boiling physics is of paramount importance for future cryogenic space applications employing Cryogenic Fluid Management (CFM) technologies. This experimental study investigates the two-phase flow and heat transfer performance of LN 2 flow boiling across five distinct flow orientations: vertical upflow, vertical downflow, horizontal flow, 45° inclined upflow, and 45° inclined downflow. The study employed the steady- state heating method within a circular heated tube featuring an 8.5-mm inner diameter and a 680-mm heated length. High-speed video recordings were utilized to capture two-phase flow patterns and interfacial behaviors across various flow orientations. The experiments covered a wide range of operating conditions, including mass velocities ranging from 351.80 to 1572.77 kg/m 2 s and inlet pressures from 297.14 to 1032.97 kPa, primarily with near-saturated inlet subcooling. Distinct two-phase flow patterns and regime transitions were identified for each flow orientation. Symmetrical flow patterns were evident in vertical orientations, whereas non-vertical orientations exhibited asymmetric flow stratifications, primarily influenced by the buoyancy force in a terrestrial gravity environment. Bubble dynamic parameters were quantified, and bubble collision and dispersion phenomena were visualized. Analyzing heat transfer performance based on local flow boiling curves and variations in heat transfer coefficients (HTCs), it was observed that vertical upflow demonstrated the most enhanced heat transfer performance, while vertical downflow exhibited the lowest. As mass velocity exceeded 830 kg/ m 2 s, the differences in heat transfer among orientations became less distinct, emphasizing the role of flow inertia in mitigating the influence of flow orientation. A direct comparison of microgravity HTC data from a recent study by the authors against the 1-𝘨 e HTC data indicated enhanced heat transfer performance in microgravity for flow orientation configurations in terrestrial gravity. However, this enhancement progressively diminished as the heat flux increased. Distinct HTC trends were observed as mass velocity increased for different flow orientations and gravity levels.

Cryogens↗
NASA NTRS2011

Numerical Modeling of the Chilldown of Cryogenic Transfer Lines Using a Sinda/GFSSP Integrated Solver

An important first step in cryogenic propellant loading is the chilldown of transfer lines. During the chilldown of the transfer line, the flow is two-phase and unsteady, with solid to fluid heat transfer and therefore a coupled thermo-fluid analysis is necessary to model the system. This paper describes a numerical model of pipe chilldown that utilizes the Sinda/GFSSP Conjugate Integrator (SGCI). SGCI is a new analysis tool developed at NASA's Marshall Space Flight Center (MSFC). SGCI facilitates the solution of thermofluid problems in interconnected solid-fluid systems. The solid component of the system is modeled in MSC Patran and translated into an MSC Sinda thermal network model. The fluid component is modeled in GFSSP, the Generalized Fluid System Simulation Program. GFSSP is a general network flow solver developed at NASA/MSFC. GFSSP uses a finite-volume approach to model fluid systems that can include phase change, multiple species, fluid transients, and heat transfer to simple solid networks. SGCI combines the GFSSP Fortran code with the Sinda input file and compiles the integrated model. Sinda solves for the temperatures of the solid network, while GFSSP simultaneously solves the fluid network for pressure, temperature, and flow rate. The two networks are coupled by convection heat transfer from the solid wall to the cryogenic fluid. The model presented here is based on a series of experiments conducted in 1966 by the National Bureau of Standards (NBS). A vacuum-jacketed, 200 ft copper transfer line was chilled by liquid nitrogen and liquid hydrogen. The predictions of transient temperature profiles and chilldown time of the integrated Sinda/GFSSP model will be compared to the experimental measurements.

LeClair, Andre↗
NASA NTRS1990

The effect of catastrophic collisional fragmentation and diffuse medium accretion on a computational interstellar dust system

The effects of catastrophic collisional fragmentation and diffuse medium accretion on a the interstellar dust system are computed using a Monte Carlo computer model. The Monte Carlo code has as its basis an analytic solution of the bulk chemical evolution of a two-phase interstellar medium, described by Liffman and Clayton (1989). The model is subjected to numerous different interstellar processes as it transfers from one interstellar phase to another. Collisional fragmentation was found to be the dominant physical process that shapes the size spectrum of interstellar dust. It was found that, in the diffuse cloud phase, 90 percent of the refractory material is locked up in the dust grains, primarily due to accretion in the molecular medium. This result is consistent with the observed depletions of silicon. Depletions were found to be affected only slightly by diffuse cloud accretion.

Liffman, Kurt↗
NASA NTRS1995

The Relative Contribution of Interaural Time and Magnitude Cues to Dynamic Sound Localization

This paper presents preliminary data from a study examining the relative contribution of interaural time differences (ITDs) and interaural level differences (ILDs) to the localization of virtual sound sources both with and without head motion. The listeners' task was to estimate the apparent direction and distance of virtual sources (broadband noise) presented over headphones. Stimuli were synthesized from minimum phase representations of nonindividualized directional transfer functions; binaural magnitude spectra were derived from the minimum phase estimates and ITDs were represented as a pure delay. During dynamic conditions, listeners were encouraged to move their heads; the position of the listener's head was tracked and the stimuli were synthesized in real time using a Convolvotron to simulate a stationary external sound source. ILDs and ITDs were either correctly or incorrectly correlated with head motion: (1) both ILDs and ITDs correctly correlated, (2) ILDs correct, ITD fixed at 0 deg azimuth and 0 deg elevation, (3) ITDs correct, ILDs fixed at 0 deg, 0 deg. Similar conditions were run for static conditions except that none of the cues changed with head motion. The data indicated that, compared to static conditions, head movements helped listeners to resolve confusions primarily when ILDs were correctly correlated, although a smaller effect was also seen for correct ITDs. Together with the results for static conditions, the data suggest that localization tends to be dominated by the cue that is most reliable or consistent, when reliability is defined by consistency over time as well as across frequency bands.

Wenzel, Elizabeth M.↗
NASA NTRS2016

Physics Based Model for Cryogenic Chilldown and Loading. Part III: Correlations

In this report we discuss the details of the correlations used to recognize flow patterns and predict frictional losses, heat and mass transfer in the cryogenic two phase flow. The emphasis are put on the formulation of the correlation problem in terms of concise parametric and functional spaces allowing for efficient online search of the model parameters and accurate prediction of the phenomena observed during cryogenic loading. A special attention is paid to the discussion of the correlation dependence on the gravity. In this context the physics of stability, friction, and boiling in the two-phase flow that underlies the required correlations is discussed.

two-phase flow↗
NASA NTRS1991

In-space experiment on thermoacoustic convection heat transfer phenomenon-experiment definition

The definition phase of an in-space experiment in thermoacoustic convection (TAC) heat transfer phenomenon is completed and the results are presented and discussed in some detail. Background information, application and potential importance of TAC in heat transfer processes are discussed with particular focus on application in cryogenic fluid handling and storage in microgravity space environment. Also included are the discussion on TAC space experiment objectives, results of ground support experiments, hardware information, and technical specifications and drawings. The future plans and a schedule for the development of experiment hardware (Phase 1) and flight tests and post-flight analysis (Phase 3/4) are also presented. The specific experimental objectives are rapid heating of a compressible fluid and the measurement of the fluid temperature and pressure and the recording and analysis of the experimental data for the establishment of the importance of TAC heat transfer process. The ground experiments that were completed in support of the experiment definition included fluid temperature measurement by a modified shadowgraph method, surface temperature measurements by thermocouples, and fluid pressure measurements by strain-gage pressure transducers. These experiments verified the feasibility of the TAC in-space experiment, established the relevance and accuracy of the experimental results, and specified the nature of the analysis which will be carried out in the post-flight phase of the report.

Parang, M.↗
NASA NTRS1972

The effect of gravity induced free convection upon the melting phenomena of a finite paraffin slab for thermal control

Two theoretical models were developed to predict the thermal response of the phase change material to a given hot plate temperature. A two-dimensional pure conduction model was developed to predict the melting of the phase change material when heat transfer was a function of conduction. A combined conduction-convection model, also two-dimensional, was developed to predict the phase change phenomena when heat transfer was a function of conduction and gravity-induced free convection. Both models were solved using explicit finite difference approximations on a digital computer. The experimental equipment consisted of a rectangular cell utilizing a heat chamber, an expansion chamber, and a test chamber; a sixteen channel multipoint recorder, and a fluid flow system. The recorder monitered hot and cold plate temperatures and interior node temperatures at two second intervals. A comparison of theoretical temperature profiles and experimental temperature profiles is presented for six runs at various angles of inclination of the test cell with respect to the horizontal direction. A detailed discussion of results is presented.

Bain, R. L.↗