Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Bifurcation analysis of the onset of necking in an elastic/plastic cylinder under uniaxial tension

The bifurcation problem governing the onset of axisymmetric necking in a circular cylindrical specimen in uniaxial tension is analysed. The specimen is made of an incompressible elastic/plastic material. One end is subject to a prescribed uniform axial displacement relative to the other and both ends are shear free. The true stress at bifurcation is greater than the stress at which the maximum load is attained by an amount which depends on (a) the radius to length ratio of the specimen, (b) the ratio of the elastic shear modulus to the tangent modulus, and (c) the derivative of the tangent modulus with respect to the stress. Bifurcation takes place immediately following attainment of the maximum load when the specimen is sufficiently slender.

Hutchinson, J. W.↗
NASA NTRS1975

Composite impact strength improvement through a fiber/matrix interphase

Research was conducted to improve the impact strength and toughness of fiber/resin composites by means of a fiber coating interphase. Graphite fiber/epoxy resin composites were fabricated with four different fiber coating systems introduced in a matrix-fiber interphase. Two graphite fibers, a high strength and a high modulus type, were studied with the following coating systems: chemical vapor deposited boron, electroless nickel, a polyamide-imide resin and a thermoplastic polysulfone resin. Evaluation methods included the following tests: Izod, flexure, shear fracture toughness, longitudinal and transverse tensile, and transverse and longitudinal compression. No desirable changes could be effected with the high strength fiber, but significant improvements in impact performance were observed with the polyamide-imide resin coated high modulus fiber with no loss in composite modulus.

Cavano, P. J.↗
NASA NTRS1975

Determination of mechanical properties of polymer film materials

Five polymeric film materials, Tedlar, Teflon, Kapton H, Kapton F, and a fiberglass reinforced polyimide, PG-402, in thickness ranging from 0.002 to 0.005 inch, were tested over a temperature range of -195 to 200 C in the "machine" and transverse direction to determine: elastic modulus, Poisson's ratio, three percent offset yield stress, fracture stress, and strain to fracture. The elastic modulus, yield stress and fracture stress decreased with increasing temperature for all the materials while the fracture strain increased. Teflon and Tedlar had the greatest temperature dependence and PG-402 the least. At 200 C the Poisson ratio values ranged from 0.39 to 0.5; they diminished as the temperature decreased covering a range of 0.26 to 0.42 at -195 C. Shortening the gauge length from eight inches to one inch increased the strain to fracture and lowered the elastic modulus values.

Hughes, E. J.↗
NASA NTRS1976

Nonlinear effects in thermal stress analysis of a solid propellant rocket motor

Direct characterization procedures were used to determine the relaxation modulus as a function of time, temperature, and state of strain. Using the quasi-elastic method of linearviscoelasticity, these properties were employed in a finite element computer code to analyze a thick-walled, nonlinear viscoelastic cylinder in the state of plane strain bonded to a thin (but stiff) elastic casing and subjected to slow thermal cooling. The viscoelastic solution is then expressed as a sequence of elastic finite element solutions. The strain-dependent character of the relaxation modulus is included by replacing the single relaxation curve used in the linear viscoelastic theory by a family of relaxation functions obtained at various strain levels. These functions may be regarded as a collection of stress histories or responses to specific loads (in this case, step strains) with which the cooldown solution is made to agree by iterations on the modulus and strain level.

Francis, E. C.↗
NASA NTRS1977

Stiffness and damping characteristics of aluminum in creep

Tensile creep tests conducted at 200 C were performed on annealed commercially pure aluminum specimens in order to measure the dominant elevated temperature dislocation processes. Testing consisted of applying small lateral loads to measure flexural stiffness, and vibrating the specimens laterally in order to measure dynamic modulus and internal damping. It was concluded that (1) the strain hardening increased static stiffness and decreased internal damping during early creep, and (2) the dynamic modulus remained essentially constant at the elastic value during creep. These results imply that primary creep may constitute a mechanism of recovery of dislocatory disorder induced by yielding the material during loading, and that the inelastic modulus utilized as a mathematical concept in several creep buckling theories is not a directly measurable material property.

Berkovits, A.↗
NASA NTRS1977

Computer simulation of the motion of a straight dislocation line in concentrated solid solutions. II

An investigation was undertaken to determine if the size and modulus interaction of a solute atom with a screw dislocation and the modulus interaction with an edge dislocation contributed to strengthening, in addition to the size interaction with an edge dislocation. The results indicate that the size interaction between solute atom and an edge dislocation accounts for most of the solid solution strengthening in f.c.c. alloys. The contribution to the yield stress from the modulus interaction with an edge dislocation is less than 15%. The interaction between a solute atom and a screw dislocation is much less than that between a solute atom and an edge dislocation.

Kuo, C. T. K.↗
NASA NTRS1977

Reduced variable technique for predicting grain behavior

The use of reduced variables to account for the time-temperature dependence of the relaxation modulus is a standard and universally adopted technique in the stress analysis of solid propellant grains. Recent work has suggested that the reduced variable technique can also be used to account for the dependence of the relaxation modulus on the crosslink density of an elastomer system. By combining variables, it is now possible to determine the relaxation modulus as a function of both mechanical and chemical parameters over a long period of time. The problems involved, the pitfalls to be avoided, and suggested techniques to be used in acquiring data are discussed.

Lewis, G. W.↗
NASA NTRS1978

Mechanical and physical properties of modern boron fibers

The results of accurate measurements of the modern boron fiber's Young's modulus, flexural modulus, shear modulus, and Poisson's ratio are reported. Physical property data concerning fiber density, thermal expansion, and resistance obtained during the course of the mechanical studies are also given.

Dicarlo, J. A.↗
NASA NTRS1978

An evaluation of the sandwich beam in four-point bending as a compressive test method for composites

The experimental phase of the study included compressive tests on HTS/PMR-15 graphite/polyimide, 2024-T3 aluminum alloy, and 5052 aluminum honeycomb at room temperature, and tensile tests on graphite/polyimide at room temperature, -157 C, and 316 C. Elastic properties and strength data are presented for three laminates. The room temperature elastic properties were generally found to differ in tension and compression with Young's modulus values differing by as much as twenty-six percent. The effect of temperature on modulus and strength was shown to be laminate dependent. A three-dimensional finite element analysis predicted an essentially uniform, uniaxial compressive stress state in the top flange test section of the sandwich beam. In conclusion, the sandwich beam can be used to obtain accurate, reliable Young's modulus and Poisson's ratio data for advanced composites; however, the ultimate compressive stress for some laminates may be influenced by the specimen geometry.

Shuart, M. J.↗
NASA NTRS1978

Mechanical and physical properties of modern boron fibers

Measurements of the Young's modulus, flexural modulus, shear modulus and Poisson's ratio for boron fibers prepared by modern deposition techniques are reported. Physical properties of the boron fibers, including density, thermal expansion and resistance, are also surveyed. In addition, prediction of the total deformation strain in an anelastic boron fiber subjected to tensile or flexural stress is discussed.

Dicarlo, J. A.↗
NASA NTRS1979

On sound transmission into an orthotropic shell

A mathematical model is presented for the transmission of airborne noise through the walls of an orthotropic cylindrical shell. Parameters were varied to see how orthotropicity affected noise transmission. When compared to that for an isotropic shell, the cylinder transmission loss was found to be quite sensitive to the ratio of circumferential to axial modulus of elasticity. A modulus ratio greater than unity appears to enhance transmission loss in the mass-controlled region, while a ratio less than unity degrades it. Below the ring frequency, the trends appear to be reversed. The cylinder transmission loss appears to be relatively insensitive to changes in the shear modulus

Koval, L. R.↗
NASA NTRS1978

Elastic constants at low temperatures - Recent measurements on technological materials at NBS

Solid-state low-temperature elastic properties have been experimentally studied at the NBS Cryogenic Division for four years. Most studies were between room temperature and liquid-helium temperature; some were only to liquid-nitrogen temperature. Two dynamic (high-frequency) experimental methods were used, pulse-echo and resonance, resulting in adiabatic elastic constants. The present paper reviews these studies for 47 technological materials - metals, alloys, and composites. The elastic constants primarily discussed are Young's modulus, the shear modulus, the bulk modulus (reciprocal compressibility), and Poisson's ratio. A summary table is presented to show which base metals tend to exhibit regular, irregular, or anomalous behavior in their elastic constant/temperature curves.

Ledbetter, H. M.↗
NASA NTRS1980

Effect of High Energy Radiation on Mechanical Properties of Graphite Fiber Reinforced Composites

The flexural strength and average modulus of graphite fiber reinforced composites were tested before and after exposure to 0.5 Mev electron radiation and 1.33 Mev gamma radiation by using a three point bending test (ASTM D-790). The irradiation was conducted on vacuum treated samples. Graphite fiber/epoxy (T300/5208), graphite fiber/polyimide (C6000/PMR 15) and graphite fiber/polysulfone (C6000/P1700) composites after being irradiated with 0.5 Mev electron radiation in vacuum up to 5000 Mrad, show increases in stress and modulus of approximately 12% compared with the controls. Graphite fiber/epoxy (T300/5208 and AS/3501-6), after being irradiated with 1.33 Mev gamma radiation up to 360 Mrads, show increases in stress and modulus of approximately 6% at 167 Mrad compared with the controls. Results suggest that the graphite fiber composites studied should withstand the high energy radiation in a space environment for a considerable time, e.g., over 30 years.

Naranong, N.↗
NASA NTRS1981

Room temperature shear properties of the strain isolator pad for the shuttle thermal protection system

Tests were conducted at room temperature to determine the shear properties of the strain isolator pad (SIP) material used in the thermal protection system of the space shuttle. Tests were conducted on both the .23 cm and .41 cm thick SIP material in the virgin state and after fifty fully reversed shear cycles. The shear stress displacement relationships are highly nonlinear, exhibit large hysteresis effects, are dependent on material orientation, and have a large low modulus region near the zero stress level where small changes in stress can result in large displacements. The values at the higher stress levels generally increase with normal and shear force load conditioning. Normal forces applied during the shear tests reduces the low modulus region for the material. Shear test techniques which restrict the normal movement of the material give erroneous stress displacement results. However, small normal forces do not significantly effect the shear modulus for a given shear stress. Poisson's ratio values for the material are within the range of values for many common materials. The values are not constant but vary as a function of the stress level and the previous stress history of the material. Ultimate shear strengths of the .23 cm thick SIP are significantly higher than those obtained for the .41 cm thick SIP.

Sawyer, J. W.↗
NASA NTRS1981

Thermal shock resistance of silicon oxynitride

The thermal shock resistance of Si2N2O refractory material was studied. The thermal expansion coeff. is 3.55x10 to the -6th power at 20 to 800 C and 2.86x10 to the -6th power m/m/deg at 20 to 200 C. The breaking loads are high at high stress. Young's modulus E and the shear modulus G decrease linearly with increasing porosity. For dense material E sub o approx. = 216,500 N/mm2 and G approx = 90,600 N/mm2. The Vickers hardness of the dense material is comparable to that of sapphire. The results on thermal shock show that R, the breaking load, stays constant for T T sub c, the first cracks appear and R decreases sharply for T=T sub c. As the severity of the thermal shock is increased at T T sub c, a small no. of new, large-size cracks appears. The shock's cumulative effect is negligible, and repeated shocks do not change the cracks. The low values of the thermal expansion coefficient and Young's modulus and the high tension breaking load are considered. Sintered Si2N2O with 5% MgO shows excellent cracking resistance under thermal shock.

Glandus, J. C.↗
NASA NTRS1982

Tensile properties of SiC/aluminum filamentary composites - Thermal degradation effects

Aluminium metal matrix composites with a low cost fiber, e.g. SiC, provide for an attractive combination of high elastic modulus and longitudinal strengths coupled with a low density. SiC (volume fraction 0.55)-aluminum (6061) systems have been studied in order to optimize fiber composite strength and processing parameters. A comparison of two SiC/aluminum composites produced by AVCO and DWA is provided. Fiber properties are shown to alter composite tensile properties and fracture morphology. The room temperature tensile strengths appear to be insensitive to thermal exposures at 500 C up to 150 h. The elastic modulus of the composites also appears to be stable up to 400 C, however variations in the loss modulus are apparent. The fracture morphology reflects the quality of the interfacial bond, fiber strengths and fiber processing.

Skinner, A.↗
NASA NTRS1983

Dynamic mechanical characterization of cure of a polyimide-graphite fiber composite (PMR 15/Celion 6000)

Dynamic mechanical studies of thermosetting PMR 15 polyimide/Celion 6000 composites were used to characterize cure behavior. Variation in composite shear modulus with cure time for laminates partially cured under 3.45 MPa pressure was compared with that of laminates fully cured under pressure to select a partially cured system whose behavior corresponded with that of the pressure-cured composites. An empirical kinetic model was developed that relates relative composite shear moduli to cure time and temperature. This model, coupled with standard statistical techniques, was used in the determination of an overall activation energy, E = 145 kj/mole (35 kcal/mole) and order of reaction, n, for the cure reaction(s). The empirical relationship defining dynamic modulus as a function of time and temperature remained linear well into the glassy region. Changes in dynamic glass-transition temperature and in the breadth of the transition peaks with cure time are discussed. Shear modulus and damping were found to be more sensitive measures of relative extent of cure than Fourier transform infrared spectroscopy.

Hurwitz, F. I.↗
NASA NTRS1983

Mechanical Property Characterization of F-100/934 Graphite-Epoxy Composite Material

Procedures for quality control, fabrication techniques, specimen machining, test methodologies, and data collection and interpretation were defined using Thornel P-100 carbon fiber combined with Fiberite's 934 epoxy resin in unidirectional tape form. Tests on the prepreg material, including gel time, resin solids content, tack, volatile content, and flow are detailed. The steps of the fabrication and machining processes are described. Both destructive and nondestructive techniques were employed to assess the properties of the cured laminates. Tests to determine tensile strength and modulus, compressive strength and modulus, interlaminar and inplane shear strength, and flexural strength and modulus are discussed. The results of these experiments are compared with data generated by other researchers.

Clinton, R. G., Jr.↗