Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mixed effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Effects of streamwise vorticity injection on turbulent mixing layer development

This paper investigates the effect of injected strong streamwise vorticity on the structure and development of a plane mixing layer originating from tripped boundary layers. The experiments were conducted in a mixing layer wind tunnel consisting of two separate legs which were driven individually by centrifugal blowers. It was found that, while the vorticity injection increased the growth rate in the near-field, the asymptotic growth rate was reduced by a factor of about two, together with the peak Reynolds stress levels. The result is attributed to the effect of the relatively strong and short wavelength streamwise vorticity in making the spanwise structures more three-dimensional and slowing down their pairing process, thus reducing entrainment, and hence growth.

Bell, James H.↗
DOE OSTI2021

Investigation of Gallium–Boron Spin-On Codoping for poly-Si/SiO x Passivating Contacts

A doping technique for p-type poly-Si/SiOx passivating contacts using a spin-on method for different mixtures of Ga and B glass solutions is presented. Effects of solution mixing ratios on the contact performance (implied open circuit voltage iV oc , contact resistivity ..rho..c) are investigated. For all as-annealed samples at different drive-in temperatures, increasing the percentage of Ga in the solution shows a decrement in iV oc (from ~680 to ~610 mV) and increment in ..rho..c (from ~3 to ~800 mO cm 2 ). After a hydrogenation treatment by depositing a SiN x /AlO x stack followed by forming gas annealing, all samples show improved iVoc (~700 mV with Ga-B co-doped, and ~720 mV with all Ga). Interestingly, when co-doping Ga with B, even a small amount of B in the mixing solution shows negative effects on the surface passivation. Active and total dopant profiles obtained by electrical capacitance voltage and secondary-ion mass spectrometry measurements, respectively, reveal a relatively low percentage of electrically-active Ga and B in the poly-Si and Si layers. Overall, these results help understand the different features of the two dopants: a low ρ c with B, a good passivation with Ga, their degree of activation inside the poly-Si and Si layers, and the annealing effects.

14 SOLAR ENERGY↗
DOE OSTI2026

The impact of aerosol mixing state on immersion freezing: insights from classical nucleation theory and particle-resolved simulations

Immersion freezing, initiated by ice-nucleating particles (INPs) in supercooled aqueous droplets, plays an important role in the formation of ice crystals within clouds. The efficiency of immersion freezing depends strongly on INP composition and, crucially, on the mixing state – how chemical species are distributed across the particle population. Here, we quantify the impact of aerosol mixing state on immersion freezing using a combined theoretical and particle-resolved modeling approach. We derive analytical expressions for the frozen fraction of internally and externally mixed INP populations based on classical nucleation theory, showing that the frozen fraction is sensitive to whether ice-active species are present in all particles or only in a subset of the population. We introduce a multi-species immersion freezing scheme into the particle-resolved model PartMC, using the water activity-based immersion freezing model (ABIFM) to compute freezing probabilities for mixed-composition particles. To improve computational efficiency, we implement a Binned Tau-Leaping algorithm and demonstrate an order-of-magnitude speedup with minimal accuracy loss. Simulations reproduce the analytical trends in limiting cases and extend the analysis to more general aerosol populations, where mixing state continues to exert a substantial control on frozen fraction. Sensitivity analyses across particle size, species type, and cooling condition reveal that the mixing state effect is most pronounced when small amounts of highly efficient INPs are mixed with less efficient materials. These findings underscore the need to represent aerosol mixing state explicitly in models of heterogeneous ice nucleation to reduce uncertainty in cloud-phase partitioning.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1973

Solutions of the chemical kinetic equations for initially inhomogeneous mixtures.

Following the recent discussions by O'Brien (1971) and Donaldson and Hilst (1972) of the effects of inhomogeneous mixing and turbulent diffusion on simple chemical reaction rates, the present report provides a more extensive analysis of when inhomogeneous mixing has a significant effect on chemical reaction rates. The analysis is then extended to the development of an approximate chemical sub-model which provides much improved predictions of chemical reaction rates over a wide range of inhomogeneities and pathological distributions of the concentrations of the reacting chemical species. In particular, the development of an approximate representation of the third-order correlations of the joint concentration fluctuations permits closure of the chemical sub-model at the level of the second-order moments of these fluctuations and the mean concentrations.

Hilst, G. R.↗
NASA NTRS1991

Effect of velocity ratio on plane mixing layer development - Influence of the splitter plate wake

The effect of the velocity ratio on the approach of a plane mixing layer to self-similarity was investigated experimentally. In the experiment, plane mixing layers with velocity ratios 0.5, 0.6, 0.7, 0.8, and 0.9 were generated in a mixing-layer wind tunnel consisting of two individually driven legs, in which the two streams were allowed to merge at the sharp edge of a tappered splitter plate. The leg driven by the bigger blower was operated at a free-stream velocity in the test section of 21 m/s, while the flow speed in the other leg was varied to change the velocity ratio. For each velocity ratio, the mean flow- and turbulence measurements were carried out at eight streamwise locations. Results showed that, for velocity ratios between 0.5 and 0.7, self-similarity of the mixing layer was achieved, with the asymptotic states comparable; mixing layers with higher velocity ratios failed to achieve a self-similar state within the measurement domain.

Mehta, R. D.↗
NASA NTRS1986

Effect of adherend thickness and mixed mode loading on debond growth in adhesively bonded composite joints

Symmetric and unsymmetric double cantilever beam (DCB) specimens were tested and analyzed to assess the effect of: (1) adherend thickness, and (2) a predominantly mode I mixed mode loading on cyclic debond growth and static fracture toughness. The specimens were made of unidirectional composite (T300/5208) adherends bonded together with EC3445 structural adhesive. The thickness was 8, 16, or 24 plies. The experimental results indicated that the static fracture toughness increases and the cyclic debond growth rate decreases with increasing adherend thickness. This behavior was related to the length of the plastic zone ahead of the debond tip. For the symmetric DCB specimens, it was further found that displacement control tests resulted in higher debond growth rates than did load control tests. While the symmetric DCB tests always resulted in cohesive failures in the bondline, the unsymmetric DCB tests resulted in the debond growing into the thinner adherend and the damage progressing as delamination in that adherend. This behavior resulted in much lower fracture toughness and damage growth rates than found in the symmetric DCB tests.

Mangalgiri, P. D.↗
NASA NTRS1991

Mixing and non-equilibrium chemical reaction in a compressible mixing layer

The effects of compressibility, chemical reaction exothermicity, and non-equilibrium chemical modeling in a reacting plane mixing layer were investigated by means of two dimensional direct numerical simulations. The chemical reaction was irreversible and second order of the type A + B yields Products + Heat. The general governing fluid equations of a compressible reacting flow field were solved by means of high order finite difference methods. Physical effects were then determined by examining the response of the mixing layer to variation of the relevant non-dimensionalized parameters. The simulations show that increased compressibility generally results in a suppressed mixing, and consequently a reduced chemical reaction conversion rate. Reaction heat release was found to enhance mixing at the initial stages of the layer growth, but had a stabilizing effect at later times. The increased stability manifested itself in the suppression or delay of the formation of large coherent structures within the flow. Calculations were performed for a constant rate chemical kinetics model and an Arrhenius type kinetic prototype. The choice of the model was shown to have an effect on the development of the flow. The Arrhenius model caused a greater temperature increase due to reaction than the constant kinetic model. This had the same effect as increasing the exothermicity of the reaction. Localized flame quenching was also observed when the Zeldovich number was relatively large.

Steinberger, Craig J.↗
DOE OSTI2020

Material Characterization of Hierarchical Tunable Pore Size Polymer Foams Used in the MARBLE Mix Morphology Experiment

One of the great challenges of inertial confinement fusion and high energy density experiments is understanding the effects of mix on thermonuclear burn. The MARBLE campaign, conceived at Los Alamos National Laboratory, aims to gather new insights into this issue by utilizing unique target capsules containing polymer foams of variable pore sizes, tunable over an order of magnitude. Such capsules allow the degree of initial heterogeneity to be controlled experimentally for the first time. Here, we describe the various characterization efforts used to gain understanding of the chemical structure and behavior of the foam. Previous experiments were not sensitive to foam physical properties, and the MARBLE platform has aided in the development of techniques to measure foam properties such as deuterium content, density variation, hydrogen adsorption, and pore size and volume distribution.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2008

Mixing of Multiple Jets with a Confined Subsonic Crossflow: Part III--The Effects of Air Preheat and Number of Orifices on Flow and Emissions in an RQL Mixing Section

This study was motivated by a goal to understand the mixing and emissions in the Rich-burn/Quick-mix/Lean-burn (RQL) combustor scheme that has been proposed to minimize the formation of oxides of nitrogen (NOx) in gas turbine combustors. The study reported herein was a reacting jet-in-crossflow experiment at atmospheric pressure. The jets were injected from the perimeter of a cylindrical duct through round-hole orifices into a fuel-rich mainstream flow. The number of orifices investigated in this study gave over- to optimum to underpenetrating jets at a jet-to-mainstream momentum-flux ratio of J = 57. The size of individual orifices was decreased as the number of orifices increased to maintain a constant total area; the jet-to-mainstream mass-flow ratio was constant at MR = 2.5. The experiments focused on the effects of the number of orifices and inlet air preheat and were conducted in a facility that provided the capability for independent variation of jet and main inlet air preheat temperature. The number of orifices was found to have a significant effect on mixing and the distributions of species, but very little effect on overall NOx emissions, suggesting that an aerodynamically optimum mixer might not minimize NOx emissions. Air preheat was found to have very little effect on mixing and the distributions of major species, but preheating both main and jet air did increase NOx emissions significantly. Although the air jets injected in the quick-mix section of an RQL combustor may comprise over 70 percent of the total air flow, the overall NOx emission levels were found to be more sensitive to main stream air preheat than to jet stream air preheat.

Holdemann, James D.↗
NASA NTRS2014

Effect of Fuel Injection and Mixing Characteristics on Pulse-Combustor Performance at High-Pressure

Recent calculations of pulse-combustors operating at high-pressure conditions produced pressure gains significantly lower than those observed experimentally and computationally at atmospheric conditions. The factors limiting the pressure-gain at high-pressure conditions are identified, and the effects of fuel injection and air mixing characteristics on performance are investigated. New pulse-combustor configurations were developed, and the results show that by suitable changes to the combustor geometry, fuel injection scheme and valve dynamics the performance of the pulse-combustor operating at high-pressure conditions can be increased to levels comparable to those observed at atmospheric conditions. In addition, the new configurations can significantly reduce the levels of NOx emissions. One particular configuration resulted in extremely low levels of NO, producing an emission index much less than one, although at a lower pressure-gain. Calculations at representative cruise conditions demonstrated that pulse-combustors can achieve a high level of performance at such conditions.

Propulsion↗
NASA NTRS1989

Effect of velocity ratio on plane mixing layer development

An experimental study has been conducted to investigate the effect of velocity ratio on the development of a plane mixing layer to self-similarity. Plane mixing layers with five different velocity ratios (0.5, 0.6, 0.7, 0.8 and 0.9) were generated in a newly designed mixing layer wind tunnel with both initial boundary layers tripped. For each velocity ratio, mean flow and turbulence measurements were obtained at eight streamwise locations with a single cross-wire probe. The results indicate that the splittter plate wake plays a very dominant and, in some cases, a lasting role in the development of the mixing layer. For velocity ratios between 0.5 and 0.7, self-similarity of the mixing layer was observed with the asymptotic states comparable. Mixing layers with the higher velocity ratios failed to achieve a self-similar state within the measurement domain. The development distance decreased with increasing velocity ratio up to 0.7, after which it appeared to increase. Almost all of the observed effects may be attributed to the presence and subsequent behavior of the splitter plate wake.

Mehta, R. D.↗
NASA NTRS1993

Effects of small changes in initial conditions on mixing layer three-dimensionality

The effects of relatively small changes in the initial conditions of the development of the 3D structure of a plane mixing layer originating from laminar boundary layers were experimentally studied. It is found that, while the exact shapes and positions of the streamwise vortex structures are not the same for the two initial conditions, their overall distribution, reorganization, and decay are very similar. The results likely that while some of the specific details of the streamwise vortex structure may be facility-dependent, a relatively strong structure which produces significant three-dimensionality should form in all mixing layers originating from laminar boundary layers. After some initial readjustments, the structure will appear in the form of counterrotating pairs of streamwise vortices which in the mean, grow with the mixing layer and decay in strength. The results also serve to warn that small changes in initial conditions may significantly affect the Reynolds stress distributions in the near field.

Plesniak, M. W.↗
DOE OSTI2025

Advancing the Understanding of Cloud Microphysical Processes and Aerosol Indirect Effects in High-Latitude Mixed-Phase Clouds by Linking ARM Measurements with Climate Model Simulations (Final Report)

The key objectives of this project were to advance our understanding of cloud microphysical characteristics and aerosol indirect effects on mixed-phase clouds in high latitudes. To improve the representation of ice and mixed-phase clouds in Earth System Models (ESMs), we propose an integrated observation and modeling study of cloud macro- and microphysical properties, including spatial heterogeneities, mass partitioning between ice crystals and supercooled liquid water, effects of ice nucleating particles (INPs), and efficiency of secondary ice production (SIP), etc. Specifically, we took four main approaches in this project: (1) examining macro- and microphysical properties of ice and mixed-phase clouds based on in-situ and ground-based observations from multiple field campaigns funded by the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) program, including the Mixed-Phase Arctic Cloud Experiment (M-PACE), Indirect and Semi-Direct Aerosol Campaign (ISDAC), Ice Nucleating Particle Sources at Oliktok Point (INPOP), ARM West Antarctic Radiation Experiment (AWARE), Measurements of Aerosols, Radiation, and Clouds over the Southern Ocean (MARCUS), and Macquarie Island Cloud and Radiation Experiment (MICRE); (2) evaluating the DOE Energy Exascale Earth System Model (E3SM) simulations based on observations, particularly for ice and mixed-phase cloud microphysical properties; (3) examining the impacts of INPs on ice and mixed-phase clouds. Specifically, a series of comparisons were conducted using observations over the Arctic, Southern Ocean, and Antarctica, including comparisons between the lower and higher southern latitudes as well as comparisons between the northern and southern hemispheres. In addition, aerosol indirect effects from distinct sources of dust particles were examined; and (4) investigating the impacts of SIP. Ultimately, these results helped to improve cloud microphysics and aerosol-cloud interaction parameterizations in the E3SM model. Overall, the project provided improved understanding regarding various factors, including thermodynamic, dynamic, and aerosol conditions, on the micro- and macrophysical properties of ice and mixed-phase clouds in the high latitudes. Resulting analysis helped to provide an improved physical basis for refining the current cloud microphysics parameterizations related to ice and mixed-phase clouds in E3SM.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2002

Measurements of Turbulent Flow Field in Separate Flow Nozzles with Enhanced Mixing Devices - Test Report

As part of the Advanced Subsonic Technology Program, a series of experiments was conducted at NASA Glenn Research Center on the effect of mixing enhancement devices on the aeroacoustic performance of separate flow nozzles. Initial acoustic evaluations of the devices showed that they reduced jet noise significantly, while creating very little thrust loss. The explanation for the improvement required that turbulence measurements, namely single point mean and RMS statistics and two-point spatial correlations, be made to determine the change in the turbulence caused by the mixing enhancement devices that lead to the noise reduction. These measurements were made in the summer of 2000 in a test program called Separate Nozzle Flow Test 2000 (SFNT2K) supported by the Aeropropulsion Research Program at NASA Glenn Research Center. Given the hot high-speed flows representative of a contemporary bypass ratio 5 turbofan engine, unsteady flow field measurements required the use of an optical measurement method. To achieve the spatial correlations, the Particle Image Velocimetry technique was employed, acquiring high-density velocity maps of the flows from which the required statistics could be derived. This was the first successful use of this technique for such flows, and shows the utility of this technique for future experimental programs. The extensive statistics obtained were likewise unique and give great insight into the turbulence which produces noise and how the turbulence can be modified to reduce jet noise.

Bridges, James↗
NASA NTRS1960

Mixing Characteristics Downstream of Core Region of High-Temperature Axisymmetric Jets Exhausting Into Transonic and Supersonic Streams

A series of rocket motors with varying exit to throat area ratios was tested in the 8- by 6-foot wind tunnel to determine the effects of mixing on jet diameter and temperature decay at large distances (x/d > 30) from the nozzle exit. An approximate method to account for effects of the initial expansion was evolved. It was determined that the combustion efficiency has an important effect on jet spreading, since the unburned products can burn downstream of the nozzle. The data showed considerable scatter; however, mixing rates were, in general, lower than those observed for subsonic jets. Data for angles of attack of 5 and 10 deg are also presented, giving the respective centerline shift and temperature decay as a function of axial distance.

Huff, Ronald G.↗
DOE OSTI2022

Experimental quantification of the impact of heterogeneous mix on thermonuclear burn

In inertial confinement fusion, deuterium–tritium (DT) fuel is brought to densities and temperatures where fusion ignition occurs. However, mixing of the ablator material into the fuel may prevent ignition by diluting and cooling the fuel. MARBLE experiments at the National Ignition Facility provide new insight into how mixing affects thermonuclear burn. These experiments use laser-driven capsules containing deuterated plastic foam and tritium gas. Embedded within the foam are voids of known sizes and locations, which control the degree of heterogeneity of the fuel. Initially, the reactants are separated, with tritium concentrated in the voids and deuterium in the foam. During the implosion, mixing occurs between the foam and gas materials, leading to DT fusion reactions in the mixed region. Here, it is shown that by measuring the ratios of DT and deuterium–deuterium neutron yields for different macropore sizes and gas compositions, the effects of mix heterogeneity on thermonuclear burn may be quantified, supporting an improved understanding of these effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1989

Optical Stark effect in the four-wave mixing and stimulated Raman spectra of N2

The influence of the optical Stark effect on spectral line shapes in four-wave-mixing Raman spectroscopy (FWMRS) and stimulated Raman spectroscopy (SRS) is investigated experimentally and theoretically. Using an experimental setup capable of rapid alternation between the simultaneous measurement of coherent Stokes Raman spectroscopy and inverse Raman spectroscopy at low and high intensities, together with a sophisticated frequency reference scheme, it was possible to perform a rather direct comparison between Stark-broadened and non-Stark-broadened spectra of both classes of Raman spectroscopies. The results demonstrate that SRS spectra show more Stark shift and broadening than their FWMRS counterparts. A discrepancy with theoretical results is pointed out, and an attempt is made to explain it.

Moosmuller, H.↗
DOE OSTI2021

Comparative study with two reduced test facilities for air-cooled RCCS scaling law

Korea Atomic Energy Research Institute (KAERI) and Argonne National Laboratory (ANL) conducted steady-state tests at constant heat flux conditions to investigate the scale effect on heat removal behavior of the air-cooled Reactor Cavity Cooling System (RCCS). Two differently scaled-down test facilities were used in this study, KAERI’s ¼ scale with 4.0-m cavity height, and ANL’s ½ scale with 6.8-m cavity height. Two scaling laws were proposed to simulate the radiation across the cavity and the buoyancy-driven duct flow in the riser, respectively. The test matrix for KAERI and ANL test facilities focused on the scaling effect of the heated riser length with constant heat flux at the PMR200 RCCS design. The test results showed that mixed convection in the riser duct is an important factor for accurately extrapolating the thermo-fluid behavior in the prototype from the test results in the scale-down facilities. The system analysis code, GAMMA+, with improved heat transfer models predicted fairly well the air-cooled RCCS test data from two facilities. GAMMA+ analysis results showed that the predicted radiation fractions on the heated plate in the scale-down test conditions were larger than those on the reactor vessel in the prototype. The scaling law for air-cooled RCCS was improved by considering the mixed convection in the riser duct and the same radiation fraction on the heated plate. The mixed convection effect was calculated by the height ratio. The same radiation fraction provided a conservative extrapolation from the scale-down test results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗