Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microporous”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Formation of the pore structure of brown coal upon thermolysis with potassium hydroxide

The pore-structure characteristics of active carbons prepared by the thermolysis (800{sup o}C) of brown coal impregnated with potassium hydroxide were studied. The dependence of the specific surface area, total pore volume, micropore volume, micropore fraction, and micropore size distribution on the KOH/coal weight ratio R{sub KOH}{le} 1.0 g/g was found. Condensation processes with the formation of a low-porosity material were predominant at low ratios of R{sub KOH} {le} 0.1 g/g. The development of a micropore structure was observed at R{sub KOH} {ge} 0.1 g/g, and it increased as R{sub KOH} was increased to 1.0 g/g. It was hypothesized that pore formation was due to the thermally initiated reactions of the structural fragments of coal with KOH molecules, which occurred within the framework of coal.

01 COAL, LIGNITE, AND PEAT↗

Search for selective ion diffusion through membranes

The diffusion rates of several ions through some membranes developed as battery separators were measured. The ions investigated were Li(+), Rb(+), Cl(-), and So4. The members were crosslinked polyvinyl alcohol, crosslinked polyacrylic acid, a copolymer of the two, crosslinked calcium polyacrylate, cellulose, and several microporous polyphenylene oxide based films. No true specificity for diffusion of any of these ions was found for any of the membranes. But the calcium polyacrylate membrane was found to exhibit ion exchange with the diffusing ions giving rise to the leaching of the calcium ion and low reproducibility. These findings contrast earlier work where the calcium polyacrylate membrane did show specificity to the diffusion of the copper ion. In general, Fick's law appeared to be obeyed. Except for the microporous membranes, the coefficients for ion diffusion through the membranes were comparable with their values in water. For the microporous membranes, the values found for the coefficients were much less, due to the tortuosity of the micropores.

May, C. E.↗

Effect of structure on current and potential distributions in porous electrode

Porous electrodes generally contain constricted macropores and localized micropores. The effects of the macropore constrictions on the resistance of a capillary were studied and an analytical model was developed for predicting the current distribution in a constricted macropore which directly includes constriction effects and does not require an empirical tortuosity parameter. The current and concentration distributions in localized micropores were also investigated and it was shown that the microporous area is fully accessible to charge and mass transfer processes. From these analyses it was concluded that the micropores primarily affect the kinetics of the interfacial processes by contributing to the interfacial area, while the macropores impose ohmic and mass transport limitations through the volume of the porous electrode.

Lanzi, Oscar↗

The electric current effect on electrochemical deconsolidation of spherical fuel elements - 18447

For High-Temperature Gas-cooled Reactor in China, fuel particles are bonded into spherical fuel elements by a carbonaceous matrix. In conjunction with the development of a system to determine fuel failure fractions through {gamma}-analysis of individual and undamaged fuel particles, an automated electrochemical deconsolidation apparatus was developed in this study to separate the particles from the carbonaceous matrix by disintegrating the matrix into fine graphite powder, based on the anodic oxidation of graphite in an electrolyte containing nitric acid. A series of tests were conducted under a range of deconsolidation conditions to develop procedures and refine the equipment. The easy-handle un-irradiated spherical fuel elements were used as samples for initial tests. It is found that the morphology, size, and element content of deconsolidated graphite matrix and free particles were notably affected by electric current intensity. During the electrolysis, the nitric acid electrolyte gradually infiltrated into the micropores of graphite matrix, and the electrochemical reaction would take place around micropore structure as well as matrix surface. With much higher surface reaction capability due to the large specific area of micropore structure, the expansion stress originated from inner surface of micropores widened the c-spacing of the layer lattice of carbonaceous matrix, which was thought to be one of the main driving force of deconsolidation. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Ultra-high aspect ratio pores milled in diamond via laser, ion and electron beam mediated processes

Microfabrication techniques are critical for the rapid prototyping and development of applications for cutting edge materials. Recently diamond has gained considerable interest for quantum photonic, biosensing, inertial confinement fusion and magnetometer applications. In this article, ultra-high aspect ratio milling of diamond micropores by photon, ion and electron based methods is reported. A multiphoton absorption laser ablation approach is revealed to rapidly produce sub-10 μm diameter micropores in diamond with an aspect ratio of 14:1 and a tapered profile at the surface interface. Chemically active, oxygen focused ion beam milling produces high-aspect ratio pores in diamond with an aspect ratio of 65:1 and minimal tapering over the length of the pore, overcoming the physical interaction volume limitations imposed in conventional gallium based focused ion beam milling and laser ablation methods. Oxygen-mediated electron beam induced etching is revealed to negate the limitations imposed by physical sputtering mechanisms utilized in focused ion beam milling via the direct initiation of chemical reactions at the receding surface, producing aspect ratios on the order of 200:1. Numerical simulations reveal the physical basis for the superior aspect-ratio pore milling of the oxygen focused ion beam milling and electron beam induced etching methods. Our results demonstrate direct-write methods for the fabrication of ultra-high aspect micropores in diamond and provide insight into the underlying mechanisms of these physical processes. The three methods demonstrated here can be interchanged for applications based on the desired characteristic aspect ratio and process throughput.

36 MATERIALS SCIENCE↗

Characterization of a Molecule Partially Confined at the Pore Mouth of a Zeotype

Abstract We investigate the interaction between a molecule and a pore mouth—a critical step in adsorption processes—by characterizing the conformation of a macrocyclic calix[4]arene‐Ti IV complex, which is grafted on the external surface of a zeotype (*‐SVY). X‐ray absorption and 13 C{ 1 H} CPMAS NMR spectroscopies independently detect a unique conformation of this complex when it is grafted at crystallographically equivalent locations that lie at the interface of 7 Å hemispherical microporous cavities and the external surface. Electronic structure calculations support the presence of this unique conformation, and suggest that it is brought about by a specific orientation of the macrocycle that maximizes non‐covalent interactions between calix[4]arene upper‐rim tert ‐butyl substituents and the microporous‐cavity walls. Our comparative study provides a rare “snapshot” of a molecule partially confined at a pore mouth, an essential intermediate for adsorption into micropores, and demonstrates how surrounding environment controls this confinement in a sensitive fashion.

Grosso‐Giordano, Nicolás A.↗

Detection of Carbocationic Species in Zeolites: Large Crystals Pave the Way

Large zeolite crystals have been used as model systems for the investigation of diffusion and catalytic reactivity phenomena in microporous host materials for at least two decades. However, their potential in assisting the detection of elusive reactive intermediates appears to have been underestimated. Herein, we show that a complementary use of vibrational and optical spectroscopy in combination with theoretical calculations allows for the unambiguous identification of transient carbocationic species generated upon the acid-catalyzed oligomerization of styrene derivatives within zeolite H-ZSM-5. Thanks to the mediated diffusion of the reactant in the large H-ZSM-5 crystals and minimal external surface the reaction intermediates can be accumulated within zeolite micropores in sufficient concentrations to allow their detection by synchrotron-based IR microspectroscopy. The UV/Vis and IR spectra display strong polarization dependence of on the molecular alignment of the dimeric styrene carbocations imposed by the zeolite channels and cages that can be rationalized in terms of the electronic and vibrational transitions of the intrazeolite carbocations. Based on these findings, a molecular-level picture of the macroscopic arrangement of the reaction intermediates confined within microporous zeolite matrices can be devised.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Grain detachment and transport clogging during mineral dissolution in carbonate rocks with permeable grain boundaries

In this paper, we explore the effect of permeable grain boundaries on carbonate rock dissolution in order to improve our understanding of grain detachment and migration during reactive flow. To do so we investigated the effects of grain size and enhanced reactivity along grain boundaries on global dissolution kinetics. Variations of permeability and porosity were calculated, and exponential relationships were observed in fractured rocks. Our model employed a reactive transport framework based on the Darcy-Brinkman equation to simulate calcite dissolution in carbonate rocks composed of microporous grains and, included fluid transport along grain boundaries. The model includes fluid flow, solute transport by advection–diffusion, heterogeneous reaction between fluid and minerals and grain detachment with subsequent grain transport in macropores. The migration of solid particles due to dissolution was based on cluster analysis and local movement, and the results show that grain detachment can lead to significant decreases in permeability due to the clogging of transport pathways. Microporous media with smaller grain sizes (fine grains in this study) showed a higher average reaction rate than those with coarser grains. In addition, as the overall rates of geochemical processes are commonly affected by the presence of texture heterogeneities such as fractures, a single fracture (macropore) introduced into a microporous matrix composed of permeable grains and grain boundaries was modelled as a large channel connecting the inlet and outlet of the simulation domain. It was found that macropore clogging by grain detachment temporary decreased permeability, lowering the long-term global reaction rates. Lastly, we observed that increases in flow rate can reduce detachment and fracture clogging by reducing local dissolution along grain boundaries.

58 GEOSCIENCES↗

Nucleate pool boiling of R-245fa at low saturation temperatures for hydrogen precooling applications

In this study, experiments were conducted to measure the pool boiling performance of saturated R-245fa at low saturation temperatures (-30 degrees C, -40 degrees C, and -50 degrees C). Horizontally oriented cylindrical heat sources were used as the test samples and were intended to simulate a small section of a hydrogen-filled tube. Measurements evaluated the effects of saturation temperature and two microporous coatings on heat transfer coefficients (HTC), critical heat flux (CHF), and boiling incipient superheat. Results show that boiling performance decreases as the saturation temperature reduces - a result of less active nucleation sites and higher vapor coverage of the heated surface at lower temperatures. Microporous coatings increased HTCs and CHF values, but did not have a significant effect on reducing the boiling incipient superheat. Finally, the experimental results were used to develop correlations for nucleate pool boiling on plain and microporous surfaces that can be used to predict HTCs and CHF values at low saturation temperature conditions (down to -50 degrees C).

08 HYDROGEN↗

Performance of a Cross-Flow Humidifier with a High Flux Water Vapor Transport Membrane

Water vapor transport (WVT) flux across a composite membrane that consists of a very thin perfluorosulfonic acid (PFSA) ionomer layer sandwiched between two expanded polytetrafluoroethylene (PTFE) microporous layers is investigated. Static and dynamic tests are conducted to measure WVT flux for different composite structures; a transport model shows that the underlying individual resistances for water diffusion in the gas phase and microporous and ionomer layers and for interfacial kinetics of water uptake at the ionomer surface are equally important under different conditions. A finite-difference model is formulated to determine water transport in a full-scale (2-m2 active membrane area) planar cross-flow humidifier module assembled using pleats of the optimized composite membrane. In agreement with the experimental data, the modeled WVT flux in the module increases at higher inlet relative humidity (RH) of the wet stream and at lower pressures, but the mass transfer effectiveness is higher at higher pressures. The model indicates that the WVT flux is highest under conditions that maintain the wet stream at close to 100% RH while preventing the dry stream from becoming saturated. The overall water transport is determined by the gradient in RH of the wet and dry streams but is also affected by vapor diffusion in the gas layer and the microporous layer.

combined thermal and mass transfer↗

A novel metal-organic framework for high storage and separation of acetylene at room temperature

A novel 3D microporous metal-organic framework with NbO topology, [Cu{sub 2}(L)(H{sub 2}O){sub 2}]∙(DMF){sub 6}·(H{sub 2}O){sub 2} (ZJU-10, ZJU = Zhejiang University; H{sub 4}L =2′-hydroxy-[1,1′:4′,1″-terphenyl]-3,3″,5,5″-tetracarboxylic acid; DMF =N,N-dimethylformamide), has been synthesized and structurally characterized. With suitable pore sizes and open Cu{sup 2+} sites, ZJU-10a exhibits high BET surface area of 2392 m{sup 2}/g, as well as moderately high C{sub 2}H{sub 2} volumetric uptake capacity of 132 cm{sup 3}/cm{sup 3}. Meanwhile, ZJU-10a is a promising porous material for separation of acetylene from methane and carbon dioxide gas mixtures at room temperature. - Graphical abstract: A new NbO-type microporous metal-organic framework ZJU-10 with suitable pore size and open Cu{sup 2+} sites was synthesized to realize the strong interaction with acetylene molecules, which can separate the acetylene from methane and carbon dioxane gas mixtures at room temperature. Display Omitted - Highlights: • A novel 3D NbO-type microporous metal-organic framework ZJU-10 was solvothermally synthesized and structurally characterized. • ZJU-10a exhibits high BET surface area of 2392 m{sup 2}/g. • ZJU-10a shows a moderately high C{sub 2}H{sub 2} gravimetric (volumetric) uptake capacity of 174 (132) cm{sup 3}/g at 298 K and 1 bar. • ZJU-10a can separate acetylene from methane and carbon dioxide gas mixtures at room temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Insights into Controls of Mineralogy and Pore Structure on the Density of Methane Adsorption Phase in Shales under Supercritical Conditions

With gradually increasing enhancing population and industrialization, exploitation of shale gas is enhancing in the world to satisfy the growing demand for energy worldwide. To exploit shale gas efficiently, accurate assessment of shale gas in place (GIP) is necessary for determining production strategies. Unlike free and dissolved gas, adsorbed gas contributes to the shale GIP up to 85% due to the well-developed surface area and micropores. Measured excess adsorption of methane (up to over 95% of subsurface shale gas) is often corrected to absolute adsorption to obtain the actual amount of adsorption under supercritical (or geological) conditions. During the correction, adsorption phase density (APD) is critical. However, the APD of subsurface shale gas and the effects of shale properties (e.g., mineralogy and pore structure) on APD remain poorly understood. A series of high-pressure methane adsorption isotherms (HPMAI) on Caney Shales were collected and analyzed in conjunction with other United States and Chinese shales from the literature at 35–125 °C and up to 15 MPa. Here, a three-layer Ono–Kondo (OK3) model is utilized to derive the temperature- and pressure-dependent APD coupling low-pressure nitrogen adsorption isotherms (LPNAI) and HPMAI. X-ray diffraction and organic geochemistry are combined to reveal the mineralogy. Brunauer–Emmett–Teller, Barrett–Joyner–Halenda, and Horvath–Kawazoe analyses via LPNAI are used to investigate the pore structures. Results show that APD increases with organic matter (OM) proxied by total organic carbon and decreases with clay minerals and the sum of quartz and feldspar. OM dramatically contributes to the APD as multiple-layer adsorption exists, and the APD for OM could be 1.4–8.5 times that for clay minerals. Other inorganic minerals contribute less to APD. The properties and constitution of the surface area instead of the volume fraction contribute to the APD in shales. APD does not show an obvious correlation with micropore volume, likely related to the ratio of micropore volume to the total pore volume. Here, we provide a significant and comprehensive study of petrological factors that impact the APD of subsurface shale gas, which will improve the estimation of supercritical adsorption and shale GIP under reservoir conditions. Also, the findings in this work can provide applications for subsurface carbon dioxide adsorption and storage.

58 GEOSCIENCES↗

NMR and Theoretical Study of In-Pore Diffusivity of Ionic Liquid–Solvent Mixtures

We report despite having a lower energy density than common batteries, electric double-layer capacitors (EDLCs) offer several advantages for high-power applications, including high power density, quick charge and discharge time, and long cycle life. Room-temperature ionic liquids (RTILs) have been intensely studied as promising electrolytes for applications in ELDCs because of their wide potential window, low volatility, as well as thermal and chemical stability. The main deficiency of neat RTILs in such applications is the sluggish diffusivity, which restricts the EDLCs’ power density. To alleviate the slow diffusivity, RTILs can be used in a mixture with organic solvents. In this study, we applied two-dimensional exchange nuclear magnetic resonance spectroscopy (2D EXSY NMR) and molecular dynamics (MD) simulations to investigate the diffusivity of anions of an RTIL, namely, 1-butyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)imide (BMIM + –TFSI – ), dissolved in five different organic solvents, in the micropores of activated carbon. We determined that the relative concentrations of ions in solutions in the micropores were higher than those in the bulk solutions and were also solvent-dependent. The ion diffusivities in the pores were found to be almost 2 orders of magnitude slower than in the bulk solutions, with methanol showing the largest relative disparity. These results suggested that the interactions of solvents with the activated carbon are critical not only to the power density of EDLCs but also to the energy density. The comparisons of ion diffusivities between the experiments and the MD simulations suggest the need to consider also the surface functionalities of activated carbon for the simulation of ion diffusion in the micropores of activated carbon.

electric double layer capacitors↗

Tunable Porosity in Fused Filament 3D-Printed Blends of Intrinsically Porous Polymer and Thermoplastic Aliphatic Polyesters Polycaprolactone and Polylactic Acid

Future advances and usage of all-organic polymeric materials with permanent void spaces and high surface areas, in applications such as separations or as supports, depends heavily on the development of processing techniques to produce complex geometry objects. Here, the high free volume glassy microporous polymer PIM-1 was fabricated, as a major component in a polymer blend, into complex and customizable 3D objects by fused filament fabrication (FFF). PIM-1 was found to be compatible with polycaprolactone (PCL) and polylactic acid (PLA) and thus could be processed by extrusion into filaments with high loadings of PIM-1 (50% by mass). Ternary PCL/PLA/PIM-1 composite filaments provided an optimal balance of durability and melt flow characteristics for consistent FFF 3D printing of intricate structures. As printed, the micropores of PIM-1 were blocked and inaccessible to N2 during sorption experiments; however, the ternary composite structures displayed significant meso- and macroporosity and nanostructured phase separation. Postprinting immersion in 3-chloro-1-propanol was identified to selectively remove PCL within the composites, re-expose the characteristic micropores of PIM-1, and retain the macrostructure of the printed object. After postprinting treatments, specific surface areas by the Brunauer–Emmett–Teller method (as high as 460 m2 g–1) were found to directly correlate with the PCL content originally present. In conclusion, the extrusion-based processing methodology provides a new approach for production of intrinsically porous polymer objects in custom and complex shapes by reinforcement with thermoplastics (PCL and PLA).

36 MATERIALS SCIENCE↗

Activated carbons from coal/pitch and polyethylene terephthalate blends for the removal of phenols from aqueous solutions

Blends of two bituminous coals and a coal-tar pitch (CTP) with polyethylene terephthalate (PET) were evaluated as precursors of activated carbons (ACs). The intensity of the interactions between the raw materials, coal/CTP and PET during copyrolysis was closely observed by means of thermogravimetric analysis. In addition, the homogeneity of the carbon matrix of the chars produced at 800{sup o}C in a horizontal oven was studied by polarized light optical microscopy. Activated carbons were prepared from single components and their blends (1:1 w/w) by subjecting them to carbonization up to 800{sup o}C in a horizontal oven and then activation with steam at 800{sup o}C to 50% burnoff. The porous structure of the ACs was determined by sorption of N{sub 2} at 77 K and of CO{sub 2} at 273 K. The PET-containing blends produced microporous activated carbons with a maximum BET surface area of nearly 1100 m{sup 2} g{sup -1} and a maximum micropore size distribution of 0.6-0.8 nm in the case of the AC from the CTP/PET blend. The addition of PET to a bituminous coal was compared with the preoxidation of coal P in air as a way to reduce thermoplasticity and to promote the development of the porous structure. The modification of bituminous coals by PET appeared to be more effective than conventional coal preoxidation treatment. The resultant ACs were tested by measuring their effectiveness in removing phenols from an aqueous solution. The adsorption of p-chlorophenol (PCP) by the ACs prepared from the PET-containing blends was slightly higher than for the commercial activated carbon. The ability to adsorb PCP was found to be related to the volume of the super-micropores.

01 COAL, LIGNITE, AND PEAT↗

Diversity-oriented synthesis of polymer membranes with ion solvation cages

Microporous polymers feature shape-persistent free volume elements (FVEs), which are permeated by small molecules and ions when used as membranes for chemical separations, water purification, fuel cells, and batteries. It remains a significant challenge to identify FVEs with analyte specificity, due to difficulties in generating microporous polymer libraries with sufficient diversity for screening their properties. Here, we describe a diversity-oriented synthetic (DOS) strategy for microporous polymer membranes from which we identified those whose FVEs serve as solid solvation cages for lithium ions (Li + ). Furthermore, key elements of our strategy included diversification of bis(catechol)-type monomers via multi-component Mannich reactions to introduce Li+-coordinating functionality within individual FVEs, topology-enforcing polymerizations for generating macromolecular skeletal diversity for networking FVEs into different pore architectures, and several classes of on-polymer reactions for diversifying pore geometries and dielectric properties. Lead candidate polymer membranes featuring explicit ion solvation cages exhibited both higher ionic conductivity and higher cation transference number than control membranes where FVEs were aspecific, which indicates conventional bounds for membrane permeability and selectivity for ion transport can be overcome.4 These advantages are tied to enhanced Li + partitioning from the electrolyte when the cages are present, higher diffusion barriers for anions within the pores, and network-enforced restrictions on the number of solvent molecules bound to Li+ by comparison to the bulk electrolyte, which reduces the effective mass of the working ion. Such membranes show promise as anode-stabilizing interlayers in high-voltage lithium-metal batteries for electric mobility.

42 ENGINEERING↗

Encapsulation of large dye molecules in hierarchically superstructured metal–organic frameworks

Microporous metal–organic frameworks (MOFs) represent a new family of microporous materials, offering potential applications in gas separation and storage, catalysis, and membranes. We expect that the engineering of hierarchical superstructured MOFs, i.e., fabricating mesopores in microporous frameworks during the crystallization stage will serve a myriad of applications for molecular adsorption, drug delivery, and catalysis. But, MOFs with mesopores are rarely studied because of the lack of a simple, effective way to construct mesoscale cavities in the structures. We report the use of a perturbation-assisted nanofusion technique to construct hierarchically superstructured MOFs. In particular, the mesopores in the MOF structure enabled the confinement of large dye species, resulting in fluorescent MOF materials, which can serve as a new type of ratiometric luminescent sensors for typical volatile organic compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗