SEARCH · Engineering Papers

Results for “met”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

NASA NTRS1976

The requirements for batteries for electric vehicles

Analysis of automobile use patterns shows that the battery requirements for an urban car can be met by mid-term battery technology. The far-term technology potentially offers greater range but does not proportionately increase the usefulness of the vehicle. This suggests that emphasis should be shifted toward more modest energy density goals, if such a shift would ease technical problems and allow the use of lower cost materials and construction methods. A technology diffusion model indicates that the impact of the mid-term batteries by the year 2000 would be greater than that of the far-term batteries because of their earlier introduction and nearly equal market potential. From the standpoint of maximizing both the cumulative impact and the benefits derived in the year 2000, however, a strategy of early introduction of near-term and mid-term cars followed by the far-term vehicle would produce the optimum results.

Schwartz, H. J.↗

NASA NTRS1976

Single phase inverter for a three phase power generation and distribution system

A breadboard design of a single-phase inverter with sinusoidal output voltage for a three-phase power generation and distribution system was developed. The three-phase system consists of three single-phase inverters, whose output voltages are connected in a delta configuration. Upon failure of one inverter the two remaining inverters will continue to deliver three-phase power. Parallel redundancy as offered by two three-phase inverters is substituted by one three-phase inverter assembly with high savings in volume, weight, components count and complexity, and a considerable increase in reliability. The following requirements must be met: (1) Each single-phase, current-fed inverter must be capable of being synchronized to a three-phase reference system such that its output voltage remains phaselocked to its respective reference voltage. (2) Each single-phase, current-fed inverter must be capable of accepting leading and lagging power factors over a range from -0.7 through 1 to +0.7.

Lindena, S. J.↗

NASA NTRS1976

Noise comparisons of single and two stage demonstrator fans for advanced technology aircraft

A high-speed single-stage and a low-speed two-stage fan were designed, fabricated, and tested to demonstrate their predicted low noise performance for an advanced 0.85-0.90 cruise Mach number aircraft requiring a 1.8-1.9 pressure ratio fan. Acoustic tests were made with both unsuppressed and suppressed configurations. The two-stage fan demonstrated that quiet fan technology developed for low-speed single-stage fan is applicable to two-stage designs. The unsuppressed high-speed single-stage fan demonstrated that significant reductions in inlet noise can be achieved from the sonic blockage caused by supersonic flow in the rotor blading. Both fans demonstrated suppressed inlet noise levels with treated sonic inlets that met advanced technology goals.

Heidmann, M. F.↗

NASA NTRS1976

Pollution technology program, can-annular combustor engines

A Pollution Reduction Technology Program to develop and demonstrate the combustor technology necessary to reduce exhaust emissions for aircraft engines using can-annular combustors is described. The program consisted of design, fabrication, experimental rig testing and assessment of results and was conducted in three program elements. The combustor configurations of each program element represented increasing potential for meeting the 1979 Environmental Protection Agency (EPA) emission standards, while also representing increasing complexity and difficulty of development and adaptation to an operational engine. Experimental test rig results indicate that significant reductions were made to the emission levels of the baseline JT8D-17 combustor by concepts in all three program elements. One of the Element I single-stage combustors reduced carbon monoxide to a level near, and total unburned hydrocarbons (THC) and smoke to levels below the 1979 EPA standards with little or no improvement in oxides of nitrogen. The Element II two-stage advanced Vorbix (vortex burning and mixing) concept met the standard for THC and achieved significant reductions in CO and NOx relative to the baseline. Although the Element III prevaporized-premixed concept reduced high power NOx below the Element II results, there was no improvement to the integrated EPA parameter relative to the Vorbix combustor.

Roberts, R.↗

NASA NTRS1976

The NASA pollution-reduction technology program for small jet aircraft engines

Three advanced combustor concepts, designed for the AiResearch TFE 731-2 turbofan engine, were evaluated in screening tests. Goals for carbon monoxide and unburned hydrocarbons were met or closely approached with two of the concepts with relatively modest departures from conventional combustor design practices. A more advanced premixing/prevaporizing combustor, while appearing to have the potential for meeting the oxides of nitrogen goal as well, will require extensive development to make it a practical combustion system. Smoke numbers for the two combustor concepts were well within the EPA smoke standard. Phase 2, Combustor-Engine Compatibility Testing, which is in its early stages, and planned Phase 3, Combustor-Engine Demonstration Testing, are also described.

Fear, J. S.↗

NASA NTRS1976

Titan/Centaur D-1TTC-5 Helios B flight data report

The fourth operational flight of the newest NASA unmanned launch vehicle is reported. The spacecraft was the Helios B, the second of two solar probes designed and built by the Federal Republic of Germany. The primary mission objective, to place the Helios spacecraft on a heliocentric orbit in the ecliptic plane with a perihelion distance of 0.29 AU, was successfully accomplished. After successful injection of the Helios spacecraft, a series of experiments were performed with the Centaur stage to demonstrate its operational capabilities. All objectives of the extended mission phase were successfully met. This report presents the analysis of the launch vehicle flight data for the primary mission phase of the TC-5 flight.

Adams, K. A.↗

NASA NTRS1976

A spacecraft-borne gradiometer mission analysis

Numerical simulations were performed to obtain the orbit- and attitude-determination requirements of a spacecraft-borne gradiometer mission. Results demonstrated that position determination of 300 meters in the along-track and cross-track directions and 50 meters in the radial direction are mission requirements. The optimal orientation of the gradiometer sensing plane is achieved when the spin vector elevation is 0 degrees. The attitude-determination requirements are 5 degrees resolution for spin-vector azimuth and 0.2 degree resolution for spin-vector elevation. When these requirements are met, 3-degree gravity anomalies can be recovered globally with an accuracy of 0.025/mm/sq s (2.5 mgals). The Appendix documents the mathematical procedures for estimating detailed gravity fields from gradiometer data.

Argentiero, P.↗

NASA NTRS1976

Shape optimization of disc-type flywheels

Techniques were developed for presenting an analytical and graphical means for selecting an optimum flywheel system design, based on system requirements, geometric constraints, and weight limitations. The techniques for creating an analytical solution are formulated from energy and structural principals. The resulting flywheel design relates stress and strain pattern distribution, operating speeds, geometry, and specific energy levels. The design techniques incorporate the lowest stressed flywheel for any particular application and achieve the highest specific energy per unit flywheel weight possible. Stress and strain contour mapping and sectional profile plotting reflect the results of the structural behavior manifested under rotating conditions. This approach toward flywheel design is applicable to any metal flywheel, and permits the selection of the flywheel design to be based solely on the criteria of the system requirements that must be met, those that must be optimized, and those system parameters that may be permitted to vary.

Nizza, R. S.↗

NASA NTRS1976

Apollo experience report: Real-time display system

The real time display system used in the Apollo Program is described; the systematic organization of the system, which resulted from hardware/software trade-offs and the establishment of system criteria, is emphasized. Each basic requirement of the real time display system was met by a separate subsystem. The computer input multiplexer subsystem, the plotting display subsystem, the digital display subsystem, and the digital television subsystem are described. Also described are the automated display design and the generation of precision photographic reference slides required for the three display subsystems.

Sullivan, C. J.↗

NASA NTRS1976

On the elastic stability of shells

A synopsis of a series of investigations into the instability of axially compressed cylindrical shells is given. The objective of the research, which was made with models, was to devise a technique of nondestructive evaluation. The results show that, with models at any rate, success was achieved. Probing methods which can be used to determine the locations of weakness and the pertinent instability load levels were devised. The research on large scale shells was undertaken to determine the critical loads under as uniform a circumferential distribution of axial compressive force as possible. It is clear from the results presented that this objective was met.

Horton, W. H.↗

NASA NTRS1976

Experimental clean combustor program, phase 2

The primary objectives of this three-phase program are to develop technology for the design of advanced combustors with significantly lower pollutant emission levels than those of current combustors, and to demonstrate these pollutant emission reductions in CF6-50C engine tests. The purpose of the Phase 2 Program was to further develop the two most promising concepts identified in the Phase 1 Program, the double annular combustor and the radial/axial staged combustor, and to design a combustor and breadboard fuel splitter control for CF6-50 engine demonstration testing in the Phase 3 Program. Noise measurement and alternate fuels addendums to the basic program were conducted to obtain additional experimental data. Twenty-one full annular and fifty-two sector combustor configurations were evaluated. Both combustor types demonstrated the capability for significantly reducing pollutant emission levels. The most promising results were obtained with the double annular combustor. Rig test results corrected to CF-50C engine conditions produced EPA emission parameters for CO, HC, and NOX of 3.4, 0.4, and 4.5 respectively. These levels represent CO, HC, and NOX reductions of 69, 90, and 42 percent respectively from current combustor emission levels. The combustor also met smoke emission level requirements and development engine performance and installation requirements.

Gleason, C. C.↗

NASA NTRS1976

Evaluation of a high power inverter for potential space applications

The ADM-006 inverter discussed utilizes a unique method of using power switching circuits to produce three-phase low harmonic content voltages without any significant filtering. This method is referred to as the power center approach to inverter design and is explained briefly. The results are presented of tests performed by MSFC to evaluate inverter performance, especially when required to provide power to nonlinear loads such as half or full wave rectified loads with capacitive filtering. Test preocedures and results are described. These tests show that the power center inverter essentially met or exceeded all of claims excluding voltage regulation (3.9 percent versus specified 3.3 percent) and would be a good candidate for high power inverter applications such as may be found on Space Station, Spacelab, etc.

Guynes, B. V.↗

NASA NTRS1975

Specification and preliminary design of an array processor

The design of a computer suited to the class of problems typified by the general circulation of the atmosphere was investigated. A fundamental goal was that the resulting machine should have roughly 100 times the computing capability of an IBM 360/95 computer. A second requirement was that the machine should be programmable in a higher level language similar to FORTRAN. Moreover, the new machine would have to be compatible with the IBM 360/95 since the IBM machine would continue to be used for pre- and post-processing. A third constraint was that the cost of the new machine was to be significantly less than that of other extant machines of similar computing capability, such as the ILLIAC IV and CDC STAR. A final constraint was that it should be feasible to fabricate a complete system and put it in operation by early 1978. Although these objectives were generally met, considerable work remains to be done on the routing system.

Slotnick, D. L.↗

NASA NTRS1975

Trajectory, atmosphere, and wind reconstruction from Viking entry measurements

During Mars entry, each Viking Lander will collect and send to earth large quantities of measurement data, both scientific and engineering in nature. Software has been developed to statistically process this and other data in order to reconstruct, for mission support purposes, the entry trajectory, an 'engineering' atmosphere, and a wind profile. Procedures are described for processing limited amounts of the available data in such a manner that the maximum amount of information can be extracted therefrom, consistent with program design, response requirements, and mission operations constraints. Results of observability studies and simulations indicate that accuracy requirements will be met.

Hopper, F. W.↗

NASA NTRS1975

Recent advances in strapdown inertial navigation

The computational requirements and basic features of strapdown gyroscopes for inertial navigation are discussed. Strapdown navigators currently require 20 to 50% of the available time of a minicomputer with a capability of several hundred thousand operations per second; memory requirements are 2000 to 3000 16-bit words. A system in which these computational demands are met by three limited capability microcomputers is described. A technique using dedicated microprocessors in the place of analog electronics in the gyroscope control loops is discussed, and attention is given to applications of microprocessor technology in redundant strapdown navigation systems and associated flight control systems.

Napjus, G. A.↗

NASA NTRS1975

The Multimission Modular Spacecraft for the 80's

The challenge to NASA is to prepare for the missions of tomorrow with manpower and funding constraints of today. The Goddard Space Flight Center has met this challenge with the Multimission Modular Spacecraft (MMS). This spacecraft design has evolved over the past six years while studying various potential missions. The key to the concept of the MMS is modularity and flexibility to accept mission unique hardware with minimum impact on the basic spacecraft bus. Beyond this, it was imperative that this multiple mission bus be cost effective even though it would not be of an optimum design for many missions having minimum performance requirements. The MMS performance and cost will capture 34 of the 43 potential spacecraft missions which have been initially studied. Gamma Ray Explorer (GRE) will be the first mission to utilize the MMS.

Bartlett, R. O.↗

NASA NTRS1975

ATS-6 - Description and performance

The Applications Technology Satellite-6 embodies a geosynchronous technology that is sensitive enough to receive signals from simple inexpensive earth-based terminals and is powerful enough to relay color television and other high-quality signals to these terminals. This was accomplished by deploying a 9.1-m parabolic reflector antenna in space, by performing precision attitude maneuvers on commands from the earth to point the reflector to selected spots on the earth's surface, and by providing communications links and necessary power to receive and rebroadcast signals transmitted from the ground. All major objectives of the ATS program have been satisfied, with specifications being met or exceeded.

Redisch, W. N.↗

NASA NTRS1975

Resolution enhancement of ERTS imagery

A method is described for combined interpolation and enhancement of ERTS multispectral scanner data sets. Previous research has shown that good enhancement is most easily achieved when there are a large number of data points contained within the radius of gyration of the system point spread function. This requirement can be met using ERTS data by interpolating the data before enhancement. By varying the interpolation scale factor the data set can be empirically matched to a precalculated optimum restoration filter. Once the proper match of data and filter has been found the enhancement can be carried out directly or the enhancement and interpolation operations can be combined into a single filter thereby greatly reducing the processing time. Experimental results of applying this technique are shown along with more conventional methods of image interpolation and enlargement.

Mcgillem, C. D.↗