SEARCH · Engineering Papers

Results for “measurement bandwidth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Stability investigation of the quadripod structure for the NASA/JPL 70-meter antenna

A new, slim-profiled, low-blockage quadripod structure was designed to support the 7.7-m-diameter subreflector for the 70-m antenna. Detailed analyses of quadripod structural stability (in frequency and buckling) are presented. The results indicate that the new quadripod design has an adequate safety margin for buckling, and its lowest natural frequency is above the control system bandwidth. The analytical design frequencies were confirmed by actual field measurements made in Spain in February 1986.

Chian, C. T.↗

NASA NTRS1987

Quantification of observed flare parameters in relation to a shear-index and verification of MHD models for flare prediction

The goal for the SAMEX magnetograph's optical system is to accurately measure the polarization state of sunlight in a narrow spectral bandwidth over the field of view of an active region to make an accurate determination of the magnetic field in that region. The instrumental polarization is characterized. The optics and coatings were designed to minimize this spurious polarization introduced by foreoptics. The method developed to calculate the instrumental polarization of the SAMEX optics is described.

Wu, S. T.↗

NASA NTRS1989

Optical interferometers for tests of relativistic gravity in space

A space-based astrometric interferometer with a large optical bandwidth is considered. POINTS (Precision Optical INTerferometry in Space) would measure the angular separation of two stars separated by about 90 deg on the sky with a nominal measurement error of 5 microarcseconds (mas). For a pair of mag 10 stars, the observation would require about 10 minutes. It is estimated that the instrument would measure daily the separation of two stars for each of about 60 pairs of stars; a random sequence of such measurements, if suitably redundant, contains the closure information necessary to detect and correct time dependent measurement biases to well below the nominal measurement accuracy. The 90 deg target separation permits absolute parallax measurements in all directions. A redundant observing schedule for 300 stars and 5 quasars would provide extra redundancy to compensate for the quasars' higher magnitude. If a nominal 30-day observation sequence were repeated 4 times per year for 10 years, stellar parameter uncertainties would be obtained of: 0.6 mas, position; 0.4 mas/y, proper motion; and 0.4 mas, parallax. This set of well-observed stars and quasars would form a rigid frame and the stars would serve as reference objects for measurements of all additional targets, as well as being targets of direct scientific interest. The instrument global data analysis since objectives are considered including a relativity test and technology.

Reasenberg, R. D.↗

NASA NTRS1992

Pulsed laser spectral measurement using a Fabry-Perot interferometer: Limits to resolution

We are developing a Doppler lidar system using the edge technique to measure atmospheric wind profiles. The edge technique requires a laser with a narrow spectral bandwidth and a high resolution optical filter. The lidar system will use a Nd:YAG laser operating at 1.064 microns and a high resolution Fabry-Perot interferometer for the edge filter. The Doppler shift measurement is made by locating the laser on the edge of the filter's spectral response function. Due to the steep slope on the edge, large changes in the filter transmission will be observed for small changes in frequency. The Doppler shift can be determined from a measurement of this change in filter transmission if the filter spectral response function in the region of the measurement is well known. Recently developed injection seeded solid state lasers have made near transform limited laser output readily available for lidar work. Injection-seeded Nd:YAG laser exhibit single mode output with smooth Gaussian temporal pulse shapes. Results of an experiment we conducted to evaluate the effects of a short Gaussian temporal input pulse on the spectral response of a high resolution Fabry-Perot interferometer are presented.

Notari, Anthony↗

NASA NTRS1994

An electromagnetic noncontacting sensor for thickness measurement in a dispersive medium

This paper describes a general purpose imaging technology developed by the U.S. Bureau of Mines (USBM) that, when fully implemented, will solve the general problem of 'seeing into the earth.' A first-generation radar coal thickness sensor, the RCTS-1, has been developed and field-tested in both underground and highwall mines. The noncontacting electromagnetic technique uses spatial modulation created by moving a simple sensor antenna in a direction along each axis to be measured while the complex reflection coefficient is measured at multiple frequencies over a two-to-one bandwidth. The antenna motion imparts spatial modulation to the data that enables signal processing to solve the problems of media, target, and antenna dispersion. Knowledge of the dielectric constant of the media is not necessary because the electrical properties of the media are determined automatically along with the distance to the target and thickness of each layer of the target. The sensor was developed as a navigation guidance sensor to accurately detect the coal/noncoal interface required for the USBM computer-assisted mining machine program. Other mining applications include the location of rock fractures, water-filled voids, and abandoned gas wells. These hazards can be detected in advance of the mining operation. This initiating technology is being expanded into a full three-dimensional (3-D) imaging system that will have applications in both the underground and surface environment.

Chufo, Robert L.↗

NASA NTRS1961

A Low-Resolution Unchopped Radiometer for Satellites

The blackbody temperature and the albedo of a planet, and the variation of both parameters with latitude, longitude, and time, are of great value in understanding the climatic and meteorological conditions of the planet. An unchopped radiometer with a wide but restricted field of view is capable of such temperature and albedo measurements. Coated thermistors mounted in highly reflective cones serve as detectors. Their performance as sensor elements is analyzed in detail herein to prove the feasibility of the measurement. The simplicity of the instrumentation and the low information bandwidth required make the experiment equally attractive for earth satellites and space probes.

Hanel, R. A.↗

NASA NTRS2004

UAV-Based L-Band SAR with Precision Flight Path Control

NASA's Jet Propulsion Laboratory is currently implementing a reconfigurable polarimetric L-band synthetic aperture radar (SAR), specifically designed to acquire airborne repeat track interferometric (RTI) SAR data, also know as differential interferometric measurements. Differential interferometry can provide key displacement measurements, important for the scientific studies of Earthquakes and volcanoes. Using precision real-time GPS and a sensor controlled flight management system, the system will be able to fly predefined paths with great precision. The radar will be designed to operate on a UAV (Unmanned Arial Vehicle) but will initially be demonstrated on a minimally piloted vehicle (MPV), such as the Proteus build by Scaled Composites. The application requires control of the flight path to within a 10 meter tube to support repeat track and formation flying measurements. The design is fully polarimetric with an 80 MHz bandwidth (2 meter range resolution) and 16 kilometer range swath. The antenna is an electronically steered array to assure that the actual antenna pointing can be controlled independent of the wind direction and speed. The system will nominally operate at 45,000 ft. The program started out as a Instrument Incubator Project (IIP) funded by NASA Earth Science and Technology Office (ESTO).

flight control↗

NASA NTRS2009

NASA Tech Briefs, July 2009

Topics covered include: Dual Cryogenic Capacitive Density Sensor; Hail Monitor Sensor; Miniature Six-Axis Load Sensor for Robotic Fingertip; Improved Blackbody Temperature Sensors for a Vacuum Furnace; Wrap-Around Out-the-Window Sensor Fusion System; Wide-Range Temperature Sensors with High-Level Pulse Train Output; Terminal Descent Sensor Simulation; A Robust Mechanical Sensing System for Unmanned Sea Surface Vehicles; Additive for Low-Temperature Operation of Li-(CF)n Cells; Li/CFx Cells Optimized for Low-Temperature Operation; Number Codes Readable by Magnetic-Field-Response Recorders; Determining Locations by Use of Networks of Passive Beacons; Superconducting Hot-Electron Submillimeter-Wave Detector; Large-Aperture Membrane Active Phased-Array Antennas; Optical Injection Locking of a VCSEL in an OEO; Measuring Multiple Resistances Using Single-Point Excitation; Improved-Bandwidth Transimpedance Amplifier; Inter-Symbol Guard Time for Synchronizing Optical PPM; Novel Materials Containing Single-Wall Carbon Nanotubes Wrapped in Polymer Molecules; Light-Curing Adhesive Repair Tapes; Thin-Film Solid Oxide Fuel Cells; Zinc Alloys for the Fabrication of Semiconductor Devices; Small, Lightweight, Collapsible Glove Box; Radial Halbach Magnetic Bearings; Aerial Deployment and Inflation System for Mars Helium Balloons; Steel Primer Chamber Assemblies for Dual Initiated Pyrovalves; Voice Coil Percussive Mechanism Concept for Hammer Drill; Inherently Ducted Propfans and Bi-Props; Silicon Nanowire Growth at Chosen Positions and Orientations; Detecting Airborne Mercury by Use of Gold Nanowires; Detecting Airborne Mercury by Use of Palladium Chloride; Micro Electron MicroProbe and Sample Analyzer; Nanowire Electron Scattering Spectroscopy; Electron-Spin Filters Would Offer Spin Polarization Greater than 1; Subcritical-Water Extraction of Organics from Solid Matrices; A Model for Predicting Thermoelectric Properties of Bi2Te3; Integrated Miniature Arrays of Optical Biomolecule Detectors; A Software Rejuvenation Framework for Distributed Computing; Kurtosis Approach to Solution of a Nonlinear ICA Problem; Robust Software Architecture for Robots; R4SA for Controlling Robots; Bio-Inspired Neural Model for Learning Dynamic Models; Evolutionary Computing Methods for Spectral Retrieval; Monitoring Disasters by Use of Instrumented Robotic Aircraft; Complexity for Survival of Living Systems; Using Drained Spacecraft Propellant Tanks for Habitation; Connecting Node; and Electrolytes for Low-Temperature Operation of Li-CFx Cells.

Source record↗

NASA NTRS2009

Discharge Oscillations in a Permanent Magnet Cylindrical Hall-Effect Thruster

Measurements of the discharge current in a cylindrical Hall thruster are presented to quantify plasma oscillations and instabilities without introducing an intrusive probe into the plasma. The time-varying component of the discharge current is measured using a current monitor that possesses a wide frequency bandwidth and the signal is Fourier transformed to yield the frequency spectra present, allowing for the identification of plasma oscillations. The data show that the discharge current oscillations become generally greater in amplitude and complexity as the voltage is increased, and are reduced in severity with increasing flow rate. The breathing mode ionization instability is identified, with frequency as a function of discharge voltage not increasing with discharge voltage as has been observed in some traditional Hall thruster geometries, but instead following a scaling similar to a large-amplitude, nonlinear oscillation mode recently predicted in for annular Hall thrusters. A transition from lower amplitude oscillations to large relative fluctuations in the oscillating discharge current is observed at low flow rates and is suppressed as the mass flow rate is increased. A second set of peaks in the frequency spectra are observed at the highest propellant flow rate tested. Possible mechanisms that might give rise to these peaks include ionization instabilities and interactions between various oscillatory modes.

Polzin, K. A.↗

NASA NTRS2014

HgCdTe e-APD Detector Arrays with Single Photon Sensitivity for Space Lidar Applications

A multi-element HgCdTe electron initiated avalanche photodiode (e-APD) array has been developed for space lidar applications. The detector array was fabricated with 4.3-μm cutoff HgCdTe which covered a spectral response from 0.4 to 4.3 μm. We have characterized a 4x4 detector array with 80 μm square elements and an integrated custom cryogenic silicon read-out integrated circuit (ROIC). The device operated at 77K inside a small closed-cycle Dewar. Measurements showed a unity gain quantum efficiency of about 90% at 1.55 μm. The bulk dark current of the HgCdTe e-APD at 77K was less than 50,000 input referred electrons/s at 12 V APD bias where the APD gain was 620 and the measured noise equivalent power (NEP) was 0.4 fW/Hz1/2. The electrical bandwidth of the ROIC was about 6 MHz, which was chosen to match the laser pulse width of our CO2 lidar. Even with the relatively low bandwidth, the high APD gain and low dark current enabled the device to detect single photon events. Because the APD was biased below the break-down voltage, the detector output was linear with the input optical signal and there was no dead-time and afterpulsing. A new series of HgCdTe e-APDs are being developed with a much wider bandwidth ROIC and higher gain HgCdTe e-APD array, which is expected to give a much better performance in linear mode photon counting applications.

HgCdTe↗

NASA NTRSDate not supplied

Cognitive Tapered Slot Circular Array Antenna for Lunar Surface Communications

In this paper, we present the design of a cognitive tapered slot circular array (TSCA) antenna with multiple electronically switched sector beams for lunar surface communication. The circular array is capable of sensing the frequency, power, and direction of arrival of the RF signals. The design of the TSCA builds on our prior work on the development of a single TSA element with a balanced microstrip/coax feed. The measured return loss of the single TSA element shows wide bandwidth with good impedance match across the 5 to 35 GHz frequency range. Additionally, the single TSA has good radiation patterns. The single TSA serves as the building block for a four-element TSCA with multiple electronically switched sector beams for sensing and communications.

Cognitive communications↗

NASA NTRSDate not supplied

Cognitive Tapered Slot Circular Array Antenna for Lunar Surface Communications

Antenna↗

NASA NTRS1993

Microgravity acceleration measurement environment characterization

The Space Acceleration Measurement System (SAMS) is a general-purpose instrumentation system designed to measure the accelerations onboard the shuttle Orbiter and shuttle/Spacelab vehicles. These measurements are used to support microgravity experiments and investigations into the microgravity environment of the vehicle. Acceleration measurement can be made at locations remote from the SAMS main instrumentation unit by the use of up to three remote triaxial sensor heads. The SAMS was developed by NASA's Lewis Research Center (LeRC) in support of NASA's microgravity science programs. In the past, numerous acceleration measurement systems have flown on various space missions. These systems were tailored to measure accelerations for a narrow set of requirements and were limited in bandwidth, dynamic range, and recording capability. In addition, these systems were mission-peculiar and not easily modified for other applications or missions. The result has been an inability to accurately assess the expected microgravity environment prior to a mission for a particular experiment and/or location. The prime science objective for SAMS on the SL-J mission will be to measure the accelerations experienced by a multitude of experiments in the two racks of the Japanese First Materials Processing Test (FMPT). The FMPT consists of a variety of materials science and life science experiments contained in racks no. 7 and no. 10. The SAMS data will be made available to the FMPT principal investigators after the mission for their analysis with the FMPT data. A secondary science objective for SAMS will be the characterization of the acceleration environment of the Spacelab module. This will include an analysis of the acceleration transfer function of the Spacelab module which will utilize the FMPT acceleration measurement along with measurements at the rack no. 9 structure. Another analytical effort to be undertaken is a general characterization of the acceleration environment of the Spacelab as an orbiting laboratory. These analysis efforts will be in conjunction with similar measurements and analyses on other SAMS Spacelab missions.

Delombard, Richard↗

NASA NTRS1970

Methods for measuring the loudness and noisiness of complex sounds

Physical and temporal aspects of sound which influence the rating of subjective noisiness are intensity, spectrum shape and bandwidth, spectral complexity, and duration. Objective rating methods include a graphic method, full octave and one-third octave methods, and methods that measure one value over all frequencies.

Kryter, K.↗

NASA NTRS1992

The Use of Subcarriers in Future DSN Missions

The performance of deep space telemetry signals that employ a residual carrier modulation technique is compared in the presence and absence of a subcarrier. When the subcarrier is present, the performance for the resulting pulse-coded modulation/phase-shift keyed/phase-modulated (PCM/PSK/PM) scheme is evaluated for both sine wave and square wave subcarriers and non-return-to zero (NRZ) data. When the subcarrier is absent, the performance for the resulting PCM/PM technique is evaluated for both the NRZ and the bi-phase data format. The comparison is based on telemetry performance as well as bandwidth efficiency. The first criterion is characterized in terms of the symbol error rate (SER) as a function of symbol SNR, loop bandwidth-to-data rate ratio, and modulation index. The bandwidth efficiency is characterized by the occupancy factor. The results of both the analysis and measurements show that when the interference-to-carrier ratio (ICR) is less than -15 dB, the performance degradation in the absence of a subcarrier is negligible. Various combinations of loop bandwidth-to-data rate ratios and modulation indices that achieve this performance are derived and listed. Bandwidth occupancy comparison indicates that PCM/PM/NRZ is the most efficient in this regard. Therefore, by eliminating the subcarrier and using the PCM/PM/NRZ scheme, many advantages can be realized without any sacrifice in performance.

Shihabi, M. M.↗

NASA NTRS1994

A Comparison of Telemetry Signals in the Presence and Absence of a Subcarrier

The performance of deep-space telemetry signals that employ a residual carrier modulation technique is compared in the presence and absence of a subcarrier. When the subcarrier is present, the performance for the resulting pulse-coded modulation/phase-shift keyed/phase-modulated (PCM/PSK/PM) scheme is evaluated for both sine-wave and square-wave subcarriers and Non-Return-to Zero (NRZ) data. When the subcarrier is absent, the performance for the resulting PCM/PM technique is evaluated for both the NRZ and the bi-phase data format. The comparison is based on telemetry performance as well as bandwidth efficiency. The first criterion is characterized in terms of the Symbol Error Rate (SER) as a function of symbol SNR, loop bandwidth-to-data rate ratio, and modulation index. The bandwidth efficiency is characterized by the occupancy factor. The results of both the analysis and measurements show that when the Interference-to-Carrier Ratio (ICR) is less than -20 dB, the performance degradation in the absence of a subcarrier is negligible. Various combinations of loop bandwidth-to-data rate ratios and modulation indices that achieve this performance are derived and listed. Bandwidth occupancy comparison indicates that PCM/PM/NRZ is the most efficient in this regard. Therefore, by eliminating the subcarrier and using the PCM/PM/NRZ scheme, many advantages can be realized without any sacrifice in performance.

Shihabi, Mazen M.↗

NASA NTRS2013

Effects of Tunable Data Compression on Geophysical Products Retrieved from Surface Radar Observations with Applications to Spaceborne Meteorological Radars

This paper presents results and analyses of applying an international space data compression standard to weather radar measurements that can easily span 8 orders of magnitude and typically require a large storage capacity as well as significant bandwidth for transmission. By varying the degree of the data compression, we analyzed the non-linear response of models that relate measured radar reflectivity and/or Doppler spectra to the moments and properties of the particle size distribution characterizing clouds and precipitation. Preliminary results for the meteorologically important phenomena of clouds and light rain indicate that for a 0.5 dB calibration uncertainty, typical for the ground-based pulsed-Doppler 94 GHz (or 3.2 mm, W-band) weather radar used as a proxy for spaceborne radar in this study, a lossless compression ratio of only 1.2 is achievable. However, further analyses of the non-linear response of various models of rainfall rate, liquid water content and median volume diameter show that a lossy data compression ratio exceeding 15 is realizable. The exploratory analyses presented are relevant to future satellite missions, where the transmission bandwidth is premium and storage requirements of vast volumes of data, potentially problematic.

cloud properties↗

DOE OSTI2023

Scaling comb-driven resonator-based DWDM silicon photonic links to multi-Tb/s in the multi-FSR regime

The use of chip-based micro-resonator Kerr frequency combs in conjunction with dense wavelength-division multiplexing (DWDM) enables massively parallel intensity-modulated direct-detection data transmission with low energy consumption. Resonator-based modulators and filters used in such systems can limit the number of usable wavelength channels due to practical constraints on the maximum achievable free spectral range (FSR). In this work, we introduce the design of multi-Tb/s comb-driven resonator-based silicon photonic links by leveraging the multi-FSR regime. We demonstrate the viability of the link architecture with yield estimates that are supported by extensive wafer-scale measurements of 704 micro-resonators fabricated in a commercial complementary metal–oxide–semiconductor foundry. We show that a 2.80 Tb/s link is realizable with a ≥6 σ yield (∼99.999%), and that aggregate bandwidths of 3.76 Tb/s and 4.72 Tb/s are possible if yield targets are relaxed (3 σ and 1 σ , respectively). All designs represent a 1.94−3.28× boost to aggregate link bandwidth while maintaining BER≤10 −10 performance, with a theoretical bandwidth of 10.51 Tb/s being possible for sufficiently robust resonators. We use high-speed BER measurements to inform co-optimization of data rate and aggressor spacing ( λ ag ), limiting any additional loss-based power penalties to off-resonance insertion loss (IL) and routing loss. This work demonstrates that, through the multi-FSR regime, there is a clear path toward Kerr comb-driven ultra-broadband, high bandwidth silicon photonic links that can support next-generation data centers and high-performance computers.

James, Aneek (ORCID:0000000262527807)↗