SEARCH · Engineering Papers

Results for “longitudinal comparison”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

Comparisons of Artemis I and Wind Tunnel Buffet Environments and Induced Structural Responses

This paper presents comparisons of buffet forcing functions (BFFs) and associated structural responses for the Space Launch System from two data sources: 1) Artemis I (AR01) Developmental Flight Instrumentation (DFI) and 2) transonic wind-tunnel (WT) tests. Failures of DFI sensors prevented the development of a complete set of flight-based BFFs, where each BFF is based on azimuthal integration over 360-degrees of unsteady pressures acquired by sensor rings placed at many longitudinal stations along the vehicle. Instead, a set of equivalent flight- and WT-based BFFs was developed based on functional DFI and WT sensors that share the same locations. Root-mean-square (rms) levels of equivalent BFFs from flight and WT data are in-family for most of the cardinal Mach numbers. However, at stations downstream of the booster forward attachment (FA) protuberance, the rms of flight-based BFFs exceed their WT counterparts. Strikingly, vortex-shedding off the FA protuberance occurs at lower frequencies during flight than in WT experiments. This frequency shift propagates onto the spectrum of flight-measured vs. WT-based structural responses. Aside from vortex-shedding frequency mismatch, a generally good agreement between AR01 and WT-based responses is an indirect indication that WT buffet environments are fairly well representative of their AR01 counterpart.

transonic buffet↗

NASA NTRSDate not supplied

Comparisons of Artemis I and Wind Tunnel Buffet Environments and Induced Structural Responses

transonic buffet↗

NASA NTRS1975

Comparison of theory and experiment for homogeneous turbulence with shear

Solutions for uniformly-sheared turbulence, in which the interaction of the turbulence with the mean shear dominates the turbulent self-interaction, are compared with experiment. An anisotropic spectral tensor, which appears general enough to represent the initial experimental turbulence, is used for the initial condition in the calculations. The evolution of one-point turbulence components and microscales, as well as two-point velocity correlations, are considered. In most cases the agreement with experiment is good. The theory correctly predicts the presence of a negative region for two-point longitudinal-velocity correlations only for point separations in the direction normal to the flow and the mean gradient.

Deissler, R. G.↗

NASA NTRS1953

Aerodynamic Characteristics of a Refined Deep-Step Planing-Tail Flying-Boat Hull with Various Forebody and Afterbody Shapes

An investigation was made in the Langley 300 mph 7-by 10-foot tunnel to determine the aerodynamic characteristics of a refined deep-step planing-tail hull with various forebody and afterbody shapes. For comparison, tests were made on a streamline body simulating the fuselage of a modern transport airplane. The results of the tests, which include the interference effects of a 21-percent-thick support wing, indicated that for corresponding configurations the hull models incorporating a forebody with a length-beam ratio of 7 had lower minimum drag coefficients than the hull models incorporating a forebody with a length-beam ratio of 5. Longitudinal and lateral stability was generally about the same for all hull models tested and about the same as that of a conventional hull.

Riebe, John M↗

NASA NTRS2011

Equivalent Longitudinal Area Distributions of the B-58 and XB-70-1 Airplanes for Use in Wave Drag and Sonic Boom Calculations

A detailed geometric description, in wave drag format, has been developed for the Convair B-58 and North American XB-70-1 delta wing airplanes. These descriptions have been placed on electronic files, the contents of which are described in this paper They are intended for use in wave drag and sonic boom calculations. Included in the electronic file and in the present paper are photographs and 3-view drawings of the two airplanes, tabulated geometric descriptions of each vehicle and its components, and comparisons of the electronic file outputs with existing data. The comparisons include a pictorial of the two airplanes based on the present geometric descriptions, and cross-sectional area distributions for both the normal Mach cuts and oblique Mach cuts above and below the vehicles. Good correlation exists between the area distributions generated in the late 1950s and 1960s and the present files. The availability of these electronic files facilitates further validation of sonic boom prediction codes through the use of two existing data bases on these airplanes, which were acquired in the 1960s and have not been fully exploited.

Tinetti, Ana F.↗

NASA NTRS1975

NASTRAN nonlinear vibration analysis of beam and frame structures

A capability for the nonlinear vibration analysis of beam and frame structures suitable for use with NASTRAN level 15.5 is described. The nonlinearity considered is due to the presence of axial loads induced by longitudinal end restraints and lateral displacements that are large compared to the beam height. A brief discussion is included of the mathematical analysis and the geometrical stiffness matrix for a prismatic beam (BAR) element. Also included are a brief discussion of the equivalent linearization iterative process used to determine the nonlinear frequency, the required modifications to subroutines DBAR and XMPLBD of the NASTRAN code, and the appropriate vibration capability, four example problems are presented. Comparisons with existing experimental and analytical results show that excellent accuracy is achieved with NASTRAN in all cases.

Mei, C.↗

NASA NTRS1999

Microwave Enhancement in Coronal Holes: Structure, Variability and Magnetic Nature

The microwave enhancement in coronal holes in comparison with the quiet Sun is a distinct and easily observed signature related to the magnetic activity. This has proven to be a new tool to study the solar atmospheric layer where the fast solar wind originates. We have developed a catalog of a large number of coronal holes using images obtained by SOHO's Extreme-ultraviolet Imaging Telescope in EUV and by the Nobeyama radioheliograph in microwaves. We also have high resolution longitudinal magnetograms obtained by SOHO's Michelson Doppler Imager. We present the statistical properties of the microwave enhancements and discuss the small-scale dynamics as revealed by the magnetograms and radioheliograms. We also discuss the geoeffectiveness of these coronal holes.

Gopalswamy, N.↗

NASA NTRS2000

Evolution of Plasmaspheric Refilling from Comparisons of Satellite Observations with Simulations by an Interhemispheric Plasmasphere Model

The evolution of the plasmasphere is closely coupled to processes governing flux tube refilling and transport. In this study we follow this evolution through a series of sequential ion observations made by the Retarding Ton Mass Spectrometer (RIMS) on the Dynamics Explorer 1 (DE1) satellite and with the intervening time intervals filled in by simulations made with the Field Line Interhemispheric Plasma (FLIP) model. The period of DE1 (approx. 7 hours) is such that nearly the same flux tubes are observed every second day, or every sixth orbit. The intervening observations provide additional information regarding longitudinal variations. Since the observations are necessarily restricted to two local time passes through the plasmasphere per orbit, the FLIP code will follow the observed flux tubes as they corotate and convect through the other local times. The simulations use the initial plasmasphere observations to define initial conditions of where the plasmapause is located and the extent of filling in the plasma trough. The composite of observations and simulations allows assessment of the degree to which the FLIP simulations accurately describe the processes which govern flux tube refilling over the two-day period between observations on the same flux tubes. To the extent that the convection electric field model in the FLIP code is accurate, this composite also provides a global picture of what is happening in and near the plasmasphere during the period. Of particular interest are changes in plasma composition as refilling proceeds.

Comfort, Richard H.↗

NASA NTRS1976

EDIN design study alternate space shuttle booster replacement concepts. Volume 2: Design simulation results

Historical weight estimating relationships were developed for the liquid rocket booster (LRB) using Saturn technology, and modified as required to support the EDIN05 study. Mission performance was computed using February 1975 shuttle configuration groundrules to allow reasonable comparison of the existing shuttle with the EDIN05 designs. The launch trajectory was constrained to pass through both the RTLS/AOA and main engine cut-off points. Performance analysis was based on a point design trajectory model which optimized initial tilt rate and exo-atmospheric pitch profile. A gravity turn was employed during the boost phase in place of the shuttle angle-of-attack profile. Engine throttling add/or shutdown was used to constrain dynamic pressure and/or longitudinal acceleration where necessary.

Demakes, P. T.↗

NASA NTRS1994

Vehicle integration effects on hypersonic waveriders

The integration of a class of hypersonic high-lift configurations known as waveriders into hypersonic cruise vehicles was evaluated. Waveriders offer advantages in aerodynamic performance and propulsion/airframe integration (PAI) characteristics over conventional hypersonic shapes. A wind-tunnel model was developed which integrates realistic vehicle components with two waverider shapes, referred to as the 'straight-wing' and 'cranked-wing' shapes. Both shapes were conical-flow-derived waveriders at a design Mach number of 4.0. The cranked-wing shape was designed to provide advantages in subsonic performance and directional stability over conventional waveriders. Experimental data and limited computational fluid dynamics (CFD) predictions were obtained over a Mach number range of 2.3 to 4.63 at a Reynolds number of 2.0x10(exp 6) per foot. The CFD predictions and flow visualization data confirmed the shock attachment characteristics of the baseline waverider shapes and illustrated the waverider flow-field properties. Both CFD predictions and experimental data showed that no significant performance degradations occur at off-design Mach numbers for the waverider shapes and the integrated configurations. The experimental data showed that the effects of adding a realistic canopy were minimal. The effects of adding engine components were to increase the drag and thus degrade the aerodynamic performance of the configuration. A significant degradation in aerodynamic performance was observed when 0 degree control surfaces were added to close the blunt base of the waverider to a sharp trailing edge. A comparison of the fully-integrated waverider models to the baseline shapes showed that the performance was significantly degraded when all of the components were added to the waveriders. The fully-integrated configurations studied here do not offer significant performance advantages over conventional hypersonic vehicles, but still offer advantages in air-breathing propulsion integration. Additionally, areas are identified in this study where improvements could be made to enhance the performance. Both fully-integrated configurations are longitudinally unstable over the Mach number range studied for unpowered conditions. The cranked-wing fully-integrated configuration provided significantly better lateral-directional stability characteristics than the straight-wing configuration.

Cockrell, Charles Edward, Jr.↗

NASA NTRS1989

Comparison of flying qualities derived from in-flight and ground-based simulators for a jet-transport airplane for the approach and landing pilot tasks

The primary objective was to provide information to the flight controls/flying qualities engineer that will assist him in determining the incremental flying qualities and/or pilot-performance differences that may be expected between results obtained via ground-based simulation (and, in particular, the six-degree-of-freedom Langley Visual/Motion Simulator (VMS)) and flight tests. Pilot opinion and performance parameters derived from a ground-based simulator and an in-flight simulator are compared for a jet-transport airplane having 32 different longitudinal dynamic response characteristics. The primary pilot tasks were the approach and landing tasks with emphasis on the landing-flare task. The results indicate that, in general, flying qualities results obtained from the ground-based simulator may be considered conservative-especially when the pilot task requires tight pilot control as during the landing flare. The one exception to this, according to the present study, was that the pilots were more tolerant of large time delays in the airplane response on the ground-based simulator. The results also indicated that the ground-based simulator (particularly the Langley VMS) is not adequate for assessing pilot/vehicle performance capabilities (i.e., the sink rate performance for the landing-flare task when the pilot has little depth/height perception from the outside scene presentation).

Grantham, William D.↗

NASA NTRS1996

A dynamic response model for pressure sensors in continuum and high Knudsen number flows with large temperature gradients

This paper develops a dynamic model for pressure sensors in continuum and rarefied flows with longitudinal temperature gradients. The model was developed from the unsteady Navier-Stokes momentum, energy, and continuity equations and was linearized using small perturbations. The energy equation was decoupled from momentum and continuity assuming a polytropic flow process. Rarefied flow conditions were accounted for using a slip flow boundary condition at the tubing wall. The equations were radially averaged and solved assuming gas properties remain constant along a small tubing element. This fundamental solution was used as a building block for arbitrary geometries where fluid properties may also vary longitudinally in the tube. The problem was solved recursively starting at the transducer and working upstream in the tube. Dynamic frequency response tests were performed for continuum flow conditions in the presence of temperature gradients. These tests validated the recursive formulation of the model. Model steady-state behavior was analyzed using the final value theorem. Tests were performed for rarefied flow conditions and compared to the model steady-state response to evaluate the regime of applicability. Model comparisons were excellent for Knudsen numbers up to 0.6. Beyond this point, molecular affects caused model analyses to become inaccurate.

Whitmore, Stephen A.↗

NASA NTRS1976

EDIN design study alternate space shuttle booster replacement concepts. Volume 1: Engineering analysis

The use of a recoverable liquid rocket booster (LRB) system to replace the existing solid rocket booster (SRB) system for the shuttle was studied. Historical weight estimating relationships were developed for the LRB using Saturn technology and modified as required. Mission performance was computed using February 1975 shuttle configuration groundrules to allow reasonable comparison of the existing shuttle with the study designs. The launch trajectory was constrained to pass through both the RTLS/AOA and main engine cut off points of the shuttle reference mission 1. Performance analysis is based on a point design trajectory model which optimizes initial tilt rate and exoatmospheric pitch profile. A gravity turn was employed during the boost phase in place of the shuttle angle of attack profile. Engine throttling add/or shutdown was used to constrain dynamic pressure and/or longitudinal acceleration where necessary. Four basic configurations were investigated: a parallel burn vehicle with an F-1 engine powered LRB; a parallel burn vehicle with a high pressure engine powered LRB; a series burn vehicle with a high pressure engine powered LRB. The relative sizes of the LRB and the ET are optimized to minimize GLOW in most cases.

Demakes, P. T.↗

NASA NTRS2020

Rotational and Translational Velocity and Acceleration Thresholds for the Onset of Cybersickness in Virtual Reality

This paper determined rotational and translational velocity and acceleration thresholds for the onset of cybersickness. Cybersickness causes discomfort and discourages the widespread use of virtual reality systems for both recreational and professional use. Visual motion or optic flow is known to be one of the main causes of cybersickness due to the sensory conflict it creates with the vestibular system. The aim of this experiment is to detect rotational and translational velocity and acceleration thresholds that cause the onset of cybersickness. Participants were exposed to a moving particle field in virtual reality for a few seconds per run. The field moved in different directions (longitudinal, lateral, roll, and yaw), with different velocity profiles (steady and accelerating), and different densities. Using a staircase procedure, that controlled the speed or acceleration of the field, we detected the threshold at which participant started to feel temporary symptoms of cybersickness. The optic flow was quantified for each motion type and by modifying the number of features, the same amount of optic flow was present in each scene. Having the same optic flow in each scene allows a direct comparison of the thresholds. The results show that the velocity and acceleration thresholds for rotational optic flow were significantly lower than for translational optic flow. The thresholds suggestively decreased with the decreasing particle density of the scene. Finally, it was found that all the rotational and translational thresholds strongly correlate with each other. While the mean values of the thresholds could be used as guidelines to develop virtual reality applications, the high variability between individuals implies that the individual tuning of motion controls would be more effective to reduce cybersickness while minimizing the impact on the experience of immersion.

Terenzi, Lorenzo↗

NASA NTRS1972

Motion simulator study of longitudinal stability requirements for large delta wing transport airplanes during approach and landing with stability augmentation systems failed

A ground-based simulator investigation was conducted in preparation for and correlation with an-flight simulator program. The objective of these studies was to define minimum acceptable levels of static longitudinal stability for landing approach following stability augmentation systems failures. The airworthiness authorities are presently attempting to establish the requirements for civil transports with only the backup flight control system operating. Using a baseline configuration representative of a large delta wing transport, 20 different configurations, many representing negative static margins, were assessed by three research test pilots in 33 hours of piloted operation. Verification of the baseline model to be used in the TIFS experiment was provided by computed and piloted comparisons with a well-validated reference airplane simulation. Pilot comments and ratings are included, as well as preliminary tracking performance and workload data.

Snyder, C. T.↗

NASA NTRS1992

Production of H-3 at large momentum in alpha-(C-12) collisions at 2A GeV

Calculations of the longitudinal and transverse momentum distributions for H-3 production at large momentum in alpha-(C-12) collisions near 2A GeV are compared to experiment. Triton exchange and final-state interactions are shown to represent large corrections to the impulse approximation for proton knockout. A method for calculating interference effects for inelastic fragmentation is discussed. Good agreement with experiment using a phenomenological overlap function for (H-3)-p is found successful in describing H-3 production in pion-induced reactions. Comparisons to momentum distributions obtained through (p, 2p) and (e, ep) reactions on He-4 are made.

Cucinotta, Francis A.↗

NASA NTRS1998

Reynolds Number Effects at High Angles of Attack

Lessons learned from comparisons between ground-based tests and flight measurements for the high-angle-of-attack programs on the F-18 High Alpha Research Vehicle (HARV), the X-29 forward-swept wing aircraft, and the X-31 enhanced fighter maneuverability aircraft are presented. On all three vehicles, Reynolds number effects were evident on the forebodies at high angles of attack. The correlation between flight and wind tunnel forebody pressure distributions for the F-18 HARV were improved by using twin longitudinal grit strips on the forebody of the wind-tunnel model. Pressure distributions obtained on the X-29 wind-tunnel model at flight Reynolds numbers showed excellent correlation with the flight data up to alpha = 50 deg. Above (alpha = 50 deg. the pressure distributions for both flight and wind tunnel became asymmetric and showed poorer agreement, possibly because of the different surface finish of the model and aircraft. The detrimental effect of a very sharp nose apex was demonstrated on the X-31 aircraft. Grit strips on the forebody of the X-31 reduced the randomness but increased the magnitude of the asymmetry. Nose strakes were required to reduce the forebody yawing moment asymmetries and the grit strips on the flight test noseboom improved the aircraft handling qualities.

Fisher, David F.↗

NASA NTRS1988

Configuration trade and code validation study on a conical hypersonic vehicle

A study has been conducted on a generic wing-cone transatmospheric vehicle at Mach numbers form 2.5 to 4.5. The objectives of the study were to experimentally define the aerodynamic characteristics of the vehicle and evaluate several computational aerodynamic prediction methods through comparison with the experimental results. The baseline wing-cone configuration fuselage consisted of a 5 deg half-angle cone forebody, cylindrical midbody, and 9 deg truncated cone afterbody. The 4-percent-thick diamond airfoil wing had an aspect ratio of 1. Several configuration variables were investigated to provide trade information on canard, wing-position and incidence, vertical tail, and nose bluntness effects. Results of the study show that wing-position and wing-incidence effects on the longitudinal aerodynamic characteristics can be significantly influenced by wing-body interference. The use of positive wing incidence to provide favorable forebody orientation for possible inlet performance improvement is accompanied by trim drag and lift-drag ratio penalties. The lateral-directional stability characteristics were strongly influenced by the location of the vertical tails. The higher-order full-potential method provided better estimates of the aerodynamic characteristics than either the linearized supersonic potential method or the tangent-cone/tangent-wedge/shock-expansion on method.

Covell, Peter F.↗