Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interface resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

In situ synchrotron x-ray studies of epitaxial SrCoO x films during ionic liquid gating

The manipulation of ions in complex oxide materials can be used to mimic brain-like plasticity through changes to the resistivity of a neuromorphic device. Advances in the design of more energy efficient devices require improved understanding of how ions migrate within a material and across its interface. We investigate the exchange of oxygen and hydrogen in a model SrCoO x epitaxial film—a material that transitions between a ferromagnetic metal and antiferromagnetic insulator depending on the oxygen concentration. Changes to the film during ionic liquid gating were measured by in situ synchrotron x-ray techniques as a function of time and gate voltage, examining the reversibility of the oxide over one complete gating cycle. We find that the out-of-plane lattice constant and oxygen vacancy concentration of SrCoO x are largely reversible although changes were observed in the ordered vacancy structure. Our results provide much needed insight into electrolyte-gated phase behavior in the transition metal oxides.

Li, Yan [Argonne National Laboratory (ANL), Argonn↗
DOE OSTI2026

Comparative study on the formation of Cr and Ti ohmic contacts to (001) β -Ga 2 O 3

Here, a comparative study of Cr/Au and Ti/Au ohmic contacts on (001) β-Ga 2 O 3 was conducted. The electrical behavior from current-voltage measurements and the interfacial composition and microstructure as determined from high-resolution transmission electron microscopy (TEM) with energy dispersive x-ray analysis were compared for the different contacts at selected points in an annealing series (300–700 °C, 1 min. anneals in N 2 ). Cr/Au contacts became ohmic at temperatures (300–350 °C) approximately 50–100 °C lower than Ti/Au contacts (400–450 °C). Cr/Au and Ti/Au contacts demonstrated optimal ohmic behavior (lowest resistance) when annealed to 450–500 and 500–600 °C, respectively, with Ti/Au contacts yielding a lower total resistance than Cr/Au. Cross-sectional TEM images of Cr/Au contacts annealed at 450 °C revealed the presence of Au nanoclusters at the Ga 2 O 3 interface and CrO x layers at both the top of the contact and the Ga 2 O 3 interface. Whereas TiO x also formed at the top and bottom interfaces in 450 °C-annealed Ti/Au contacts, the TiO x surface layer appeared to be variable in thickness and/or discontinuous, unlike the CrO x surface layer. Au nanoclusters were not detected at the interface in the Ti/Au contacts. The interdiffusion and oxidation observed in both contact metallizations point to the need for diffusion barriers that may allow these contacts to be used in future Ga 2 O 3 -based devices that operate at elevated temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Simulated Start-Stop and the Impact of Catalyst Layer Redox on Degradation and Performance Loss in Low-Temperature Electrolysis

Stress tests are developed that focus on anode catalyst layer degradation in proton exchange membrane electrolysis due to simulated start-stop operation. Ex situ testing indicates that repeated redox cycling accelerates catalyst dissolution, due to near-surface reduction and the higher dissolution kinetics of metals when cycling to high potentials. Similar results occur in situ, where a large decrease in cell kinetics (>70%) is found along with iridium migrating from the anode catalyst layer into the membrane. Additional processes are observed, however, including changes in iridium oxidation, the formation of thinner and denser catalyst layers, and platinum migration from the transport layer. Increased interfacial weakening is also found, adding to both ohmic and kinetic loss by adding contact resistances and isolating portions of the catalyst layer. Repeated shutoffs of the water flow further accelerate performance loss and increase the frequency of tearing and delamination at interfaces and within catalyst layers. These tests were applied to several commercial catalysts, where higher loss rates were observed for catalysts that contained ruthenium or high metal content. These results demonstrate the need to understand how operational stops occur, to identify how loss mechanisms are accelerated, and to develop strategies to limit performance loss.

08 HYDROGEN↗
DOE OSTI2021

High-voltage insulator having multiple materials

High-voltage insulators are disclosed that are capable of handling diverse requirements, such as providing high standoff voltages, high temperature cycling, and the ability to withstand flexural stress. One high-voltage insulator includes a first piece formed from a first material, a second piece formed from a second material, and an interface section where the first piece contacts with and forms a seal with the second piece. The interface includes a first groove located that accommodates a first gasket, sets of matching threads on the first and second pieces. The interface section further accommodates a second gasket. In this multi-piece high-voltage insulator, the first material can have a first set of flexural, heat resistance, and electrical standoff characteristics suitable for a first environment, and the second material can have a second set of flexural, heat resistance and electrical standoff characteristics suitable for a second environment.

Podpaly, Yuri Anatoly↗
DOE OSTI2023

High-voltage insulators having multiple materials

High-voltage insulators are disclosed that are capable of handling diverse requirements, such as providing high standoff voltages, high temperature cycling, and the ability to withstand flexural stress. One high-voltage insulator includes a first piece formed from a first material, a second piece formed from a second material, and an interface section where the first piece contacts with and forms a seal with the second piece. The interface includes a first groove located that accommodates a first gasket, sets of matching threads on the first and second pieces. The interface section further accommodates a second gasket. In this multi-piece high-voltage insulator, the first material can have a first set of flexural, heat resistance, and electrical standoff characteristics suitable for a first environment, and the second material can have a second set of flexural, heat resistance and electrical standoff characteristics suitable for a second environment.

Podpaly, Yuri Anatoly↗
DOE OSTI2022

Scalable, Ultrathin, and High-Temperature-Resistant Solid Polymer Electrolytes for Energy-Dense Lithium Metal Batteries

We report all-solid-state batteries (ASSBs) demonstrate great promise, offering high energy density, good thermal stability, and safe operation compared with traditional Li-ion batteries. Among various solid-state electrolytes (SSEs), solid polymer electrolytes (SPEs) offer an attractive choice due to their thinness, low density, and good manufacturability. However, ultrathin SPEs that work with practical current densities or at high temperatures remain challenging, limiting applicable conditions of SPE-based batteries. Here, the authors report a novel scalable, ultrathin, and high-temperature-resistant SPE for ASSBs. This design includes an electrospun polyacrylonitrile (PAN) matrix and polyethylene oxide (PEO)/Li salt ionic conductor, which offers a stable LiF and Li 3 N containing SSE/Li interface. The unique interface—as well as the good mechanical strength—inhibits lithium dendrites and prevents short circuiting. As a result, symmetrical Li-Li cells deliver more than 300 h cyclability at 0.5 mA cm -2 . ASSBs fabricated with only 5 µm-thickness PAN-PEO/lithium bis(trifluoromethanesulfonyl)imide reach 300 cycles at 0.3 C rate at 60 °C. The excellent thermal stability of PAN also results in safer SPEs at high temperatures. The design extends battery operation up to temperatures of 120 and 150 °C, where it achieves 500 cycles at C/2 rate and 100 cycles at 2C rate, respectively.

25 ENERGY STORAGE↗
DOE OSTI2022

Structural measurement of electron-phonon coupling and electronic thermal transport across a metal-semiconductor interface

Scattering of energetic charge carriers and their coupling to lattice vibrations (phonons) in dielectric materials and semiconductors are crucial processes that determine the functional limits of optoelectronics, photovoltaics, and photocatalysts. The strength of these energy exchanges is often described by the electron-phonon coupling coefficient, which is difficult to measure due to the microscopic time- and length-scales involved. In the present study, we propose an alternate means to quantify the coupling parameter along with thermal boundary resistance and electron conductivity by performing a high angular-resolution time-resolved X-ray diffraction measurement of propagating lattice deformation following laser excitation of a nanoscale, polycrystalline metal film on a semiconductor substrate. Our data present direct experimental evidence for identifying the ballistic and diffusive transport components occurring at the interface, where only the latter participates in thermal diffusion. This approach provides a robust measurement that can be applied to investigate microscopic energy transport in various solid-state materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Trap Passivation for Reducing On-Resistance and Saturation Voltage in Wafer-Bonded InGaAs-Channel/GaN-Drain Vertical FETs

High frequency and high power are the driving forces behind semiconductor transistor technology. However, conventional devices have the tradeoff of either being high speed or high breakdown—but not both. Wafer-bonded current aperture vertical electron transistors (BAVETs) help eliminate the tradeoff by combining a high-speed III-As channel to a high-breakdown III-N drift region. The device presented herein comprises of an InAlAs gate-barrier/InGaAs channel, wafer-bonded to an InGaN/GaN drift region, with the InGaAs/InGaN interface referred to as the wafer-bonded interface (WBI). The electronic behavior of WBIs is yet less known but necessary in realizing the potential of a BAVET. Herein, strong trap activity at the WBI is shown to be the cause of abnormally high saturation voltage ( V DS_SAT ) in BAVETs. The traps cause unintentional space charge (SC) region in the drain region of the device. This causes a drain resistance, a higher ON-resistance ( R ON ), and a higher V DS_SAT . Here, the challenge is overcome by hydrogen passivation of traps at WBI by using a p-doping for the InAlAs layer, which reduces the trap-charge concentration at the WBI. Consequently, the width of the SC region is reduced and a reduction in V DS_SAT is demonstrated, wherein it reduces from >12 to 5 V.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Constructing high-performance radiation-resistant ternary YSZ-MgO-CNT nanocomposites via tailored nanostructures

Developing long-lifetime bulk-form ceramic-based materials with high irradiation resistance is crucial for advanced nuclear systems. Here, we incorporated carbon nanotubes (CNTs) into yttria-stabilized zirconia (YSZ) and magnesia (MgO) nanocrystals to fabricate bulk YSZ-MgO-CNT nanocomposites with abundant ternary nanostructures by spark plasma sintering. To understand the role of tailored ternary nanostructure on irradiation, we investigated the microstructure and mechanical properties evolutions of the YSZ-MgO-CNT nanocomposites irradiated by multi-energy He + ions at high temperature to different fluences. Compared with the single-phase YSZ and ultrafine-grained YSZ-MgO composites, the YSZ-MgO-CNT nanocomposites possessed higher ability to manage irradiation-induced He bubbles/defects via the defect-interface interactions of proposed “loading-unloading” and “loading-transporting-unloading” mechanisms for controlling the dynamical behaviors of He atoms/defects in the CNT-doped ternary nanostructures, thereby presenting more stable microstructure and better performance in resisting irradiation hardening. In conclusion, this work provides insight into the design of advanced inert matrix nuclear fuel and new nuclear waste management materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Self-Healing, Improved Efficiency Solid State Rechargeable Li/I 2 Based Battery

Solid state electrolytes are receiving significant interest due to the prospect of improved safety, however, addressing the incidence and consequence of internal short circuits remains an important issue. In this study, a battery based on a LiI-LiI(HPN) 2 solid state electrolyte demonstrated self-healing after internal shorting where the cells recovered and continued to cycle effectively. The functional rechargeable electrochemistry of the self-forming Li/I 2 -based battery was investigated through interfacial modification by inclusion of Li metal (at the negative interface), and/or fabricated carbon nanotube substrates at the positive interface. A cell design with lithium metal at the negative and a carbon substrate at the positive interface produced Coulombic efficiencies > 90% over 60 cycles. Finally, the beneficial effects of moderately elevated temperature were established where a 10 °C temperature increase led to ~5× lower resistance.

25 ENERGY STORAGE↗
DOE OSTI2025

Investigation of the Mechanical Degradation of Zinc-Based Cold Spray Coatings for Steel Pipelines

Internal corrosion in wet natural gas is a big challenge in the oil and gas industry due to corrosive constituents such as carbon dioxide (CO2), hydrogen sulfide (H2S), other forms of sulfur, and water in the gas stream. To mitigate internal corrosion, zinc-based cold spray coatings were designed for use in natural gas pipelines to increase the lifespan of the pipeline network. However, one of the requirements in designing internal coatings is the resistance of the coatings to mechanical forces applied on the pipeline's internal wall during pigging operations. These forces are primarily compressive and shear/friction forces. This study examines material properties that must be considered when evaluating mechanical considerations. To determine the viability of the developed coatings with respect to the shear/friction forces, the shear adhesion and wear resistance of the materials have been evaluated. Shear adhesion testing was performed with modified clevises to determine the shear stress required to cause adhesion failure at the coating/substrate interface. Scanning electron microscopy was utilized to characterize the interfaces after failure. Wear testing was performed on coatings and pipeline materials utilizing pin-on-drum testing. These tests display the stress limitations and wear that the coatings can tolerate from pigging.

mechanical degradation↗
DOE OSTI2022

Characterization of the structure and chemistry of the solid–electrolyte interface by cryo-EM leads to high-performance solid-state Li-metal batteries

Solid-state lithium-metal (Li 0 ) batteries are gaining traction for electric vehicle applications because they replace flammable liquid electrolytes with a safer, solid-form electrolyte that also offers higher energy density and better resistance against Li dendrite formation. Solid polymer electrolytes (SPEs) are highly promising candidates because of their tunable mechanical properties and easy manufacturability; however, their electrochemical instability against lithium metal (Li 0 ), mediocre conductivity, and poorly understood Li 0 /SPE interphases have prevented extensive application in real batteries. In particular, the origin of the low Coulombic efficiency (CE) associated with SPEs remains elusive, as the debate continues as to whether it originates from unfavored interfacial reactions or lithium dendritic growth and dead lithium formation. In this work, we use state-of-the-art cryo-electromicroscopy (cryoEM) imaging and spectroscopic techniques to characterize the structure and chemistry of the interface between Li 0 and a polyacrylate-based SPE. Contradicting the conventional knowledge, we find that no protective interphase forms, owing to the sustained reactions between deposited Li dendrites and polyacrylic backbones and succinonitrile plasticizer. Due to the reaction induced volume change, large amounts of cracks form inside the Li dendrites with a stress corrosion-cracking behavior, indicating that Li0cannot be passivated in this SPE system. Based on this observation, we then introduce additive engineering leveraging on the knowledge of liquid electrolytes, and demonstrate that the Li 0 surface can be effectively protected against corrosion using fluoroethylene carbonate (FEC), leading to densely packed Li 0 domes with conformal and stable solid-electrolyte interphases (SEIs) films. Owing to the high room temperature ionic conductivity of 1.01 mS/cm -1 , the high transference number of 0.57 and the stabilized lithium electrolyte interface, this improved new SPE delivers an excellent lithium plating/stripping CE of 99% and 1800 hours of stable cycling in Li||Li symmetric cells (0.2 mA/cm -2 , 1mAh/cm -2 ). Furthermore, this improved cathodic stability along with the high anodic stability enables record high cycle life of >2000 cycles for Li||LiFePO 4 and >400 cycles for Li||LiCoO 2 full cells.

25 ENERGY STORAGE↗
DOE OSTI2021

Development and characteristics of ultra high-performance lightweight cementitious composites (UHP-LCCs)

Highlights: • An ultra high-performance lightweight cementitious composite (UHP-LCC) was designed. • The UHP-LCCs had ultra high strength (>120 MPa) and very low density (3 ). • The UHP-LCCs had high structural efficiency, good functional properties and superior durability. • The strategies and mechanisms on achieving UHP-LCCs with excellent performance were proposed. High strength and light weight are two recent opposite development trends of concrete. This study proposed a design concept of an ultra high-performance lightweight cementitious composite (UHP-LCC), which had a compressive strength of higher than 120 MPa and an air-dried density down to around 1800 kg/m{sup 3}. The UHP-LCCs were innovatively developed by incorporating micro-sized hollow particles with a high strength shell (hollow glass microspheres, HGM) into an ultra-high performance cementitious composite (UHPC). The roles of HGM in the UHP-LCCs were investigated by evaluating the reactivity of the HGM and the mechanisms on achieving the excellent mechanical properties, low density and superior durability were revealed. The Chapelle test results showed that the HGM exhibited some pozzolanic reactivity, which facilitated the reaction between the shell of HGM and the alkali hydration products of the paste matrix. This chemical reaction was conducive to improving the HGM-paste interface and enhancing the mechanical properties. With the use of microspheres with a high stiff shell, the fundamental properties of the UHP-LCCs including thermal insulation, sound absorption, resistance to water ingress and electrical resistivity were improved significantly. The strategies for preparing the UHP-LCCs with high structural efficiency and great performance were proposed. The results of this study provide a new approach for designing and producing a lightweight UHPC, which would be a promising material for long-span structures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Conformal high-entropy oxide coatings enable fast and durable surface oxygen reactions

Developing active and durable air electrodes for efficient oxygen reactions is challenging for protonic ceramic cells (PCCs), especially at temperatures below 550°C. Here, in this study, we report a rationally designed conformal coating with a high-entropy PrNi 0.2 Mn 0.2 Co 0.2 Fe 0.2 Cu 0.2 O 3−δ (PNMCFC) perovskite structure on the surface of a state-of-the-art PrBaCo 2 O 5+δ (PBC) air electrode. The formed hybrid air electrode (PNMCFC-PBC) shows faster surface oxygen kinetics and a more stable phase structure in high-humidity air than the bare PBC electrode. Further density functional theory calculations suggest that the conformal coating mitigates Ba segregation at the interface and improves oxygen-related reactions, enhancing overall stability and electrocatalytic performance. The cells with the developed hybrid electrodes show encouraging electrochemical performance at 550°C: a polarization resistance of 0.72 Ω cm 2 , a peak power density of 1.30 W cm −2 , an electrolysis current density of −1.36 A cm −2 at 1.3 V, and reasonable operating stabilities (∼200 h at 550°C).

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Damage initiation and evolution in Al-Si layered microstructures under shock loading conditions at atomic scales

Designing materials with microstructural features like multiphase interfaces have shown significant promise for usage in the next generation defense and nuclear applications. The dynamic response of these interfaces in extreme environments is observed to vary with the deformability of individual phases, which could subsequently alter the favored damage nucleation sites related to spall failure. Here, we investigate the role of spacing of interfaces in a nanocrystalline layered Aluminum-Silicon system on the shock wave propagation behavior, and microstructural and defect evolution using classical molecular dynamics simulations. The simulations are carried out with different hypothetical Al/Si microstructures including variations in the distribution of Si grains as layers in a nanocrystalline Al matrix. The molecular dynamics simulations suggest that spall failure is preferentially initiated at Al/Si interfaces. In addition, for the same system volume and same concentration of Si, a higher number of layers is marked by an increase in shock wave velocity and reduced resistance to spall failure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

TOF-SIMS analysis of decoherence sources in superconducting qubits

Superconducting qubits have emerged as a potentially foundational platform technology for addressing complex computational problems deemed intractable with classical computing. Despite recent advances enabling multiqubit designs that exhibit coherence lifetimes on the order of hundreds of μs, material quality and interfacial structures continue to curb device performance. Two-level system defects in the thin superconducting film and adjacent dielectric regions introduce stochastic noise and dissipate electromagnetic energy at the cryogenic operating temperatures. In this study, we utilize time-of-flight secondary ion mass spectrometry to understand the role specific fabrication procedures play in introducing such dissipation mechanisms in these complex systems. We interrogated Nb thin films and transmon qubit structures fabricated through slight modifications in the processing and vacuum conditions. We find that when the Nb film is sputtered onto the Si substrate, oxide and silicide regions are generated at various interfaces. We also observe that impurity species, such as niobium hydrides and carbides, are incorporated within the niobium layer during the subsequent lithographic patterning steps. The formation of these resistive compounds likely impacts the superconducting properties of the Nb thin film. Additionally, we observe the presence of halogen species distributed throughout the patterned thin films. We conclude by hypothesizing the source of such impurities in these structures in an effort to intelligently fabricate superconducting qubits and extend coherence times moving forward.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

IMG/PR: a database of plasmids from genomes and metagenomes with rich annotations and metadata

Plasmids are mobile genetic elements found in many clades of Archaea and Bacteria. They drive horizontal gene transfer, impacting ecological and evolutionary processes within microbial communities, and hold substantial importance in human health and biotechnology. To support plasmid research and provide scientists with data of an unprecedented diversity of plasmid sequences, we introduce the IMG/PR database, a new resource encompassing 699 973 plasmid sequences derived from genomes, metagenomes and metatranscriptomes. IMG/PR is the first database to provide data of plasmid that were systematically identified from diverse microbiome samples. IMG/PR plasmids are associated with rich metadata that includes geographical and ecosystem information, host taxonomy, similarity to other plasmids, functional annotation, presence of genes involved in conjugation and antibiotic resistance. The database offers diverse methods for exploring its extensive plasmid collection, enabling users to navigate plasmids through metadata-centric queries, plasmid comparisons and BLAST searches. The web interface for IMG/PR is accessible at https://img.jgi.doe.gov/pr. Plasmid metadata and sequences can be downloaded from https://genome.jgi.doe.gov/portal/IMG_PR.

59 BASIC BIOLOGICAL SCIENCES↗