Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hydrogen fueling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Parametric trade studies on a Shuttle 2 launch system architecture

A series of trade studies are presented on a complementary architecture of launch vehicles as a part of a study often referred to as Shuttle-2. The results of the trade studies performed on the vehicles of a reference Shuttle-2 mixed fleet architecture have provided an increased understanding of the relative importance of each of the major vehicle parameters. As a result of trades on the reference booster-orbiter configuration with a methane booster, the study showed that 60 percent of the total liftoff thrust should be on the booster and 40 percent on the orbiter. It was also found that the liftoff thrust to weight ratio (T/W) on the booster-orbiter should be 1.3. This leads to a low dry weight and still provides enough thrust to allow the design of a heavy lift architecture. As a result of another trade study, the dry weight of the reference booster-orbiter was chosen for a variety of operational considerations. Other trade studies on the booster-orbiter demonstrate that the cross feeding of propellant during boost phase is desirable and that engine-out capability from launch to orbit is worth the performance penalty. Technology assumptions made during the Shuttle-2 design were shown to be approx. equivalent to a 25 percent across the board weight reduction over the Space Shuttle technology. The vehicles of the Shuttle-2 architecture were also sized for a wide variety of payloads and missions to different orbits. Many of these same parametric trades were also performed on completely liquid hydrogen fueled fully reusable concepts. If a booster-orbiter is designed using liquid hydrogen engines on both the booster and orbiter, the total vehicle dry weight is only 3.0 percent higher than the reference dual-fuel booster-orbiter, and the gross weight is 3.8 percent less. For this booster-orbiter vehicle, a liftoff T/W of 1.3, a thrust of about 60 percent on the booster, and a Mach staging number of 3 all proved to be desirable. This modest dry weight increase for a liquid hydrogen fueled Shuttle-2 system should be more than offset by the elimination of the entire hydrocarbon engine development program and the savings in operation cost realized by the elimination of an entire fuel type.

Stanley, Douglas O.↗
NASA NTRS2007

Fatigue Life of Haynes 188 Superalloy in Direct Connect Combustor Durability Rig

The Direct Connect Combustor Durability Rig (DCR) will provide NASA a flexible and efficient test bed to demonstrate the durability of actively cooled scramjet engine structure, static and dynamic sealing technologies, and thermal management techniques. The DCR shall be hydrogen fueled and cooled, and test hydrogen coolded structural panels at Mach 5 and 7. Actively cooled Haynes 188 superalloy DCR structural panels exposed to the combustion environment shall have electrodischarge machined (EDM) internal cooling holes with flowing liquid hydrogen. Hydrogen combustion could therefore produce severe thermal conditions that could challenge low cycle fatigue durability of this material. The objective of this study was to assess low cycle fatigue capability of Haynes 188 for DCR application. Tests were performed at 25 and 650 C, in hydrogen and helium environments, using specimens with low stress ground (LSG) and electro-discharge machined (EDM) surface finish. Initial fatigue tests in helium and hydrogen indicate the low cycle fatigue life capability of Haynes 188 in hydrogen appears quite satisfactory for the DCR application. Fatigue capability did not decrease with increasing test temperature. Fatigue capability also did not decrease with EDM surface finish. Failure evaluations indicate retention of ductility in all conditions. Additional tests are planned to reconfirm these positive trends.

Gabb, TIm↗
DOE OSTI2024

Preignition mitigation strategy for gaseous fuel engine

Operating a gaseous fuel engine system includes detecting preignition in one or more of a plurality of cylinders based on a monitored cylinder pressure during combustion of a gaseous fuel such as a gaseous hydrogen fuel. Operating a gaseous fuel engine system also includes reducing a fuel injection amount for the one or more of the plurality of cylinders to a derated fuel injection amount that is based on a timing of the detected preignition. Fuel injection amount may be reduced to a greater relative extent if detected preignition is early, and to a lesser relative extent if detected preignition is later, in an engine cycle. Related apparatus and control logic is also disclosed.

Graziano, Jr., Michael T.↗
NASA NTRS1989

Plasma torch igniter for scramjets

A small, uncooled plasma torch was developed and used in combination with an injector designed to study ignition and flameholding in hydrogen-fueled supersonic flows. The plasma torch was operated on mixtures of hydrogen and argon with total flows of 10 to 70 scfh. The fuel injector design consisted of five small upstream pilot fuel injectors, a rearward facing step for recirculation, and three main fuel injectors downstream of the step. The plasma torch was located in the recirculation region, and all injection was perpendicular to the Mach 2 stream. Both semi-freejet and ducted tests were conducted. The experimental results indicate that a low power plasma torch operating on a 1:1 volumetric mixture of hydrogen and argon and located in the recirculation zone fueled by the upstream pilot fuel injectors is a good igniter for flow conditions simulating a flight Mach number of 3.7. The total temperature required to autoignite the hydrogen fuel for this injector geometry was 2640 R. The injector configuration was shown to be a good flameholder over a wide range of total temperature. Spectroscopic measurements were used to verify the presence of air total temperatures below 1610 R.

Wagner, Timothy C.↗
NASA NTRS2011

Sustainable Mars Sample Return

The proposed Mars sample return mission will be completed using natural Martian resources for the majority of its operations. The system uses the following technologies: In-Situ Propellant Production (ISPP), a methane-oxygen propelled Mars Ascent Vehicle (MAV), a carbon dioxide powered hopper, and a hydrogen fueled balloon system (large balloons and small weather balloons). The ISPP system will produce the hydrogen, methane, and oxygen using a Sabatier reactor. a water electrolysis cell, water extracted from the Martian surface, and carbon dioxide extracted from the Martian atmosphere. Indigenous hydrogen will fuel the balloon systems and locally-derived methane and oxygen will fuel the MAV for the return of a 50 kg sample to Earth. The ISPP system will have a production cycle of 800 days and the estimated overall mission length is 1355 days from Earth departure to return to low Earth orbit. Combining these advanced technologies will enable the proposed sample return mission to be executed with reduced initial launch mass and thus be more cost efficient. The successful completion of this mission will serve as the next step in the advancement of Mars exploration technology.

Alston, Christie↗
DOE OSTI2024

Uncertainty Quantification of Fatigue Behavior of Rough AM Surfaces and Microstructures to Enable Hydrogen Gas Turbine Combustion

Modification of fossil-fueled industrial gas turbines to accept no/low carbon fuels (Hydrogen, H2/natural gas blends) is a significant undertaking. Successful deployment of this technology sits at the intersection of three design criteria (1) new functional fuel injectors that can burn these fuels, (2) manufacturability to meet cost and time-to-market targets, and (3) durability in the harsh environment of an operating turbine. Additive manufacturing (AM) provides accelerated product development. However, uncertainty remains around the durability of parts with rough AM surfaces. A fully experimental approach towards quantifying fatigue performance of rough AM microstructures is costly and laborious. Instead, Solar Turbines Incorporated (Solar) proposes the use of a crystal plasticity finite element (CPFE) model to quantify the factors that drive AM surface fatigue behavior. Solar will use the CPFE results, along with targeted experimental data, to train a computationally efficient surrogate model that can be incorporated into existing turbine part lifing methods.

08 HYDROGEN↗
NASA NTRS1974

Theoretical nitric oxide production incidental to autoignition and combustion of several fuels homogeneously dispersed in air under some typical hypersonic flight conditions

A reaction package of 100 chemical reactions and attendant reaction rate constants defined for the autoignition and combustion of four carbonaceous fuels, CH4, CH3OH, C2H6, and C2H5OH. Definition of the package was made primarily by means of comparison between trial calculations and experimental data for the autoignition of CH4. Autoignition and combustion of each of these four fuels was calculated under three sets of conditions realistic for hypersonic flight applications, for comparison to hydrogen fuel, particularly with respect to formation of nitric oxide. Results show that, for all of the fuels including hydrogen, if NO production is a significant problem, compromise must be made between approaching equilibrium heat release and approaching equilibrium NO concentration.

Bahn, G. S.↗
DOE OSTI2026

Heavy Duty Hydrogen: Reference Station, Fueling Performance Test Device Concepts, and Station Capacity Model (CRADA Final Report)

This project will provide valuable information on (1) reference station design, (2) exploration of design concepts for a fueling performance test device, and (3) modeling of station capacity. The work applies to heavy-duty (HD) hydrogen fueling stations with large dispensing capacity and high flowrates servicing HD hydrogen trucks such as class 8 trucks in long haul applications. Additionally, a 4th area will provide near-real-time verification of fuel quality with on-site hydrogen contaminant detectors (HCDs) for use at both light-duty (LD) and HD stations. The work leverages national lab capabilities including staff and equipment at SNL, NLR, and ANL with collaboration and funding cost share from California agencies (CEC, SCAQMD, and GO-Biz). This project will provide tools and information that lead to more efficient design, acceptance, and commissioning of these larger capacity, higher flowrate stations serving HD applications. The HCD work will benefit both LD and HD stations. Note: The 4th area (HCD) mentioned above continued outside of this CRADA and will not be included in this report. There are no tasks included in this CRADA for HCD and the summary text for it should have been removed prior to this CRADA contract execution but remained in error and is included here for completeness.

08 HYDROGEN↗
DOE OSTI2021

H2@Airports (Workshop Summary Report)

This report serves as the proceedings of the H2@Airports Workshop held virtually by the U.S. Department of Energy (DOE) in collaboration with the U.S. Department of Transportation (DOT) and Department of Defense (DOD), November 4-6, 2020. Presentations from the workshop can be found at H2@Airports Workshop: https://www.energy.gov/eere/fuelcells/h2airports-workshop. The workshop was held to assess the state of the art for electric aircraft and airport applications specifically using hydrogen fuel cells, to discuss operational requirements and lessons learned on early fuel cell aviation and airport projects, to understand current technology gaps, to identify collaborative research and development (R&D) opportunities, to highlight codes, standards, safety, and regulatory challenges, and to identify potential actions that address them. Experts and stakeholders from industry, government, and academia met to discuss the current state of the art of hydrogen and fuel cell technologies and the requirements for using these technologies in aviation applications and land-based applications at airports. This report summarizes the discussions and diverse opinions expressed at the workshop.

08 HYDROGEN↗
DOE OSTI2024

Intensification and Integration of Hydrogen and Ammonia Production

In this project the Colorado School of Mines developed a more efficient method for on-site and on-demand generation of high purity hydrogen from ammonia for hydrogen fueling stations. Used primarily as a fertilizer, ammonia is the world’s highest volume commodity chemical. Having 17.6% hydrogen by mass, it also shows potential as a hydrogen carrier and carbon-free fuel. The team developed new technology to generate fuel cell quality hydrogen from ammonia using a catalytic membrane reactor (CMR). In addition, during the project we pivoted to use this CMR technology for the production of NH3/H2 mixtures for use in clean combustion applications. We demonstrated that these mixtures may serve as a drop-in replacement for conventional hydrocarbons such as natural gas. This project entails development of new catalysts, new membranes, and their innovative integration. This project helped generate >$4M in follow on funding at Mines, and resulted in the formation of a clean tech startup, Blaze Energy Technologies, which has licensed IP developed in this project and is working to commercialize this technology.

08 HYDROGEN↗
DOE OSTI2025

Operational optimization for multi-functional charging station with electric and hydrogen-powered vehicles

The rapid adoption of electric vehicles (EVs) and hydrogen fuel cell vehicles (HFCVs), combined with global efforts to reduce carbon emissions, has accelerated the development of EV charging and hydrogen refueling stations. In response to this demand, this paper introduces the concept of Multi-Functional Charging Station (MFCS) that integrates power generation, EV charging, battery swapping, and hydrogen refueling. A comprehensive operational model is developed for the MFCS that couples electricity and hydrogen conversion and storage technologies to enhance infrastructure utilization and improve overall system efficiency. The model also considers multiple revenue streams, including participation in energy and ancillary markets. To validate the effectiveness of the proposed model and evaluate its performance, a series of numerical experiments are conducted with different charger numbers, different electricity purchase limits, and different charger allocations. Numerical results demonstrate that shared charger configurations can lead to 8.11 % improvement in operational profit by improving resource utilization and reducing the number of depleted batteries at the end of operations compared to allocated charger setups. By varying the number of chargers, sensitivity analysis identifies diminishing marginal returns beyond about 45 chargers, suggesting it as an optimal sizing point under current settings. The integration of electricity and hydrogen conversion is also explored under scenarios with limited external electricity purchases. In conclusion, these findings indicate that optimizing charger allocation and energy management can significantly enhance station productivity and profitability, ultimately supporting the broader adoption of electrified and hydrogen-based transportation solutions.

Charging station↗
DOE OSTI2025

The levelized cost of exergy: a technoeconomic framework for energy system comparison

While the levelized costs of electricity and heat have been quantified before, these two metrics cannot be directly compared, due to the different exergy content of heat and work. To address this, we develop a levelized cost of exergy (LCOEx) framework that enables direct comparisons between energy sources and processes. We find that moderate- and high-grade heat have an LCOEx that is comparable to electricity (5–10 ¢ per kWh ex ), while low-grade heat sources have much higher LCOEx values (>50 ¢ per kWh ex ). The LCOEx of a system's output is affected by (i) the LCOEx of the system input, (ii) the CAPEX of the system, and (iii) the exergetic efficiency of the system. We use our framework to identify which processes are already achieved with relatively high cost effectiveness (production of fuels, hydrogen, and ammonia) and which have room for improvement (dehumidification, food production).

08 HYDROGEN↗