Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “graph analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Evaluation of a three-dimensional empirically derived wing at supersonic speeds

A novel wing design concept is introduced which takes advantage of the existence of conical flow at supersonic speeds. The present wing design concept is to create a near conical wing geometry by redistributing airfoils in a spanwise direction. In addition, a set of graphs which review the supersonic aerodynamics of delta wings have been employed to select a design wing sweep and Mach number. An iteration through the wing design logic resulted in the selection of a 65 deg swept delta wing and a design Mach number of 1.62. Theoretical analysis was performed with a nonlinear full-potential analysis method to assess the merits of the wing design approach. The analysis showed large reductions in drag due to lift compared to delta wings configured with traditional thickness and airfoil distributions.

Wood, Richard M.↗
NASA NTRS1976

Cost/benefit tradeoffs for reducing the energy consumption of the commercial air transportation system. Volume 1: Technical analysis

The effectiveness and associated costs of operational and technical options for reduced fuel consumption by Douglas aircraft in the domestic airline fleet are assessed. Areas explored include alternative procedures for airline and flight operations, advanced and state of the art technology, modification and derivative configurations, new near-term aircraft, turboprop configuration studies, and optimum aircraft geometry. Data for each aircraft studied is presented in tables and graphs.

Kraus, E. F.↗
NASA NTRS1980

Evaluation of SLAR and thematic mapper MSS data for forest cover mapping using computer-aided analysis techniques

To facilitate comparison between the four different spatial resolution of the NS-001 MSS data sets, a supervised approach was taken in defining training blocks for each of the different cover types. The training fields representing each cover type category were grouped and this group was clustered to determine the individual spectral classes within each cover type category which would effectively characterize the entire test site. Graphs show the variation in spectral response level with respect to distance in the across track dimension for four sampling intervals. Radar digitization procedures were developd. Flight characteristics and parameters for digitization of radar imagery are tabulated. The statement of work for phase 3 was reviewed and modifications were suggested to meet funding reduction.

Hoffer, R. M.↗
NASA NTRS1987

Ozone reference models for CIRA

The data bases and computational techniques used in recent models of the O3 distribution in the earth atmosphere are described, summarizing the results of ongoing efforts to define an O3 reference model for incorporation into CIRA. Consideration is given to the analysis of data from satellite instruments (Nimbus 7 LIMS, TOMS, and SBUV; SME UVS and IR; and AE-2 SAGE) to construct models of total column O3 and vertical O3 structure. The satellite-based model predictions are then compared with balloon, rocket, and umkehr measurements in extensive graphs: good agreement is demonstrated both among the satellite data sets and between satellite and nonsatellite data sets.

Keating, G. M.↗
NASA NTRSDate not supplied

Effects of Varying the Heat Transfer Coefficient on Engine Performance

A physics-based Nuclear Thermal Propulsion (NTP) Testing Reference Design (TRD) power balance model was coded in Simulink to investigate engine performance for various design and parameter modifications. Since the primary mode of heat transfer in NTP engines is convective, the convective heat transfer coefficient (HTC) is a key parameter that requires accurate representation. The industry standard Westinghouse correlation has an uncertainty of ±20% which was investigated in this study. The results showed that a 20% decrease in the HTC led to a 4.14% increase in maximum fuel temperature while a 20% decrease in the HTC led to a 1.81% decrease in maximum fuel temperature suggesting that narrowing the uncertainty of this correlation through experimental work would be a critical step in the development of NTP engines. Furthermore, a maximum fuel temperature relationship with specific impulse was developed for the TRD engine which showed potential engine operation between specific impulse values of 715 and 900 seconds with minimal changes to the engine design. This graph could be useful for high level vehicle performance estimations for fuel types with different maximum operating temperatures.

Heat Transfer Coefficient↗
NASA NTRS1971

Estimating Weibull parameters for materials

The statistical analysis of strength and fracture of materials in general, with application to fiber composites are discussed. The weakest link model is considered in a fairly general form, and the resulting equations are demonstrated by using a Weibull distribution for flaws. This distribution appears naturally in a variety of problems, and therefore additional attention is devoted to analysis and statistical estimation connected with this distribution. Special working charts are included to facilitate interpretation of observed data and estimation of parameters. Implications of the size effect are considered for various kinds of flaw distributions. Failure and damage in a fiber-reinforced system are described. Some useful graphs are included for predicting the strength of such a system. Recent data on organic-fiber (PRD 49) composite material is analyzed by the Weibull distribution with the methods presented.

Robinson, E. Y.↗
NASA NTRS1984

LANDSAT-4 Thematic Mapper Modulation Transfer Function (MTF) evaluation

Results of MTF analysis of imagery of the San Mateo Bridge are consistent on two TM image dates for bands 4,5, and 7. There are indications that bands 1, 2, and 3 suffer from low image contrast, and consequently low signal to noise in the derived MTFs. The two image analysis produced reasonable results along +45 deg and -45 deg azimuths in the 2-D MTF, but poor results along the 0 deg and 90 deg azimuths. The effective instantaneous field of view is given for each band, and the image contrast for water and the bridge are compared. Graphs show overall TM system MTFs.

Schowengerdt, R.↗
NASA NTRS1988

Micromechanical analysis of the time-dependent response of unidirectional composites

The micromechanical model of Aboudi (1982, 1984, and 1986) is used to predict the time-dependent creep behavior of viscoelastic-matrix composites with unidirectional elastic-fiber reinforcement. The derivation of the model and its numerical implementation are outlined, and predictions for T300/934 CFRP at 72 and 250 F are compared with experimental measurements in extensive tables and graphs. Good agreement is demonstrated, and the applicability of the present approach to composite laminates and hybrid materials such as ARALL is indicated.

Yancey, R. N.↗
NASA NTRS1991

Development of a calibrated software reliability model for flight and supporting ground software for avionic systems

The object of this project was to develop and calibrate quantitative models for predicting the quality of software. Reliable flight and supporting ground software is a highly important factor in the successful operation of the space shuttle program. The models used in the present study consisted of SMERFS (Statistical Modeling and Estimation of Reliability Functions for Software). There are ten models in SMERFS. For a first run, the results obtained in modeling the cumulative number of failures versus execution time showed fairly good results for our data. Plots of cumulative software failures versus calendar weeks were made and the model results were compared with the historical data on the same graph. If the model agrees with actual historical behavior for a set of data then there is confidence in future predictions for this data. Considering the quality of the data, the models have given some significant results, even at this early stage. With better care in data collection, data analysis, recording of the fixing of failures and CPU execution times, the models should prove extremely helpful in making predictions regarding the future pattern of failures, including an estimate of the number of errors remaining in the software and the additional testing time required for the software quality to reach acceptable levels. It appears that there is no one 'best' model for all cases. It is for this reason that the aim of this project was to test several models. One of the recommendations resulting from this study is that great care must be taken in the collection of data. When using a model, the data should satisfy the model assumptions.

Lawrence, Stella↗
NASA NTRSDate not supplied

Effects of Heat Transfer Coefficient Variation on Nuclear Thermal Propulsion Engine Performance

A physics-based Nuclear Thermal Propulsion (NTP) Testing Reference Design (TRD) power balance model was coded in Simulink to investigate engine performance for various design and parameter modifications. Since the primary mode of heat transfer in NTP engines is convective, the convective heat transfer coefficient (HTC) is a key parameter that requires accurate representation. The industry standard Westinghouse correlation has an uncertainty of ±20% which was investigated in this study. The results showed that a 20% decrease in the HTC led to a 4.14% increase in maximum fuel temperature while a 20% decrease in the HTC led to a 1.81% decrease in maximum fuel temperature suggesting that narrowing the uncertainty of this correlation through experimental work would be a critical step in the development of NTP engines. Furthermore, a maximum fuel temperature relationship with specific impulse was developed for the TRD engine which showed potential engine operation between specific impulse values of 715 and 900 seconds with minimal changes to the engine design. This graph could be useful for high level vehicle performance estimations for fuel types with different maximum operating temperatures.

Heat Transfer Coefficient↗
NASA NTRS1988

An analysis of satellite observations of the O I EUV dayglow

Observations of the latitudinal variation of the 1356-A, 1304-A, and 989-A O I earth dayglow, obtained with the USAF STP78-1 satellite at solar maximum on March 21, 1979, are reported and compared with the predictions of thermospheric models and published laboratory measurements of electron-impact excitation cross sections. The results are presented in extensive tables and graphs and characterized in detail, with particular attention to the 1304-A solar flux and the 989-A branching ratio. The STP78-1 data (as well as simultaneous AE-E satellite measurements ) are shown to indicate exospheric temperatures that were 220-240-K higher, but varied significantly less with latitude, than those predicted by the MSIS-83 model (Hedin, 1983) for the day of the observations.

Link, R.↗
NASA NTRS1972

Gas-core reactor power transient analysis.

The nuclear fuel in the gas-core reactor concept is a ball of uranium plasma radiating thermal photons. The photons are met by an inflowing hydrogen stream, which is seeded with submicron size, depleted uranium particles. A 'wall-burnout' condition exists if the thermal photons can reach the cavity liner because of insufficient absorption by the hydrogen. An analysis was conducted in order to determine the time for which the maximum steady state reactor power could be exceeded without damage to the cavity liner due to burnout. Wall-burnout time as a function of the power increase above the initial steady state condition is shown in a graph.

Kascak, A. F.↗
NASA NTRS1975

Research investigation of the physical interactions and phenomena associated with hypervelocity sub-micron particles

Signals from impact ionization plasmas were studied as a means of performing microparticle composition analysis. Impact ionization signal response was measured in a time-of-flight (TOF) system for lanthanum hexaboride, carbonyl iron, and aluminum microparticle impacts on a tantalum target, primarily in the 1 - 8 km/s velocity range. Oscilloscope photographs of representative ion TOF signal response are given for each material studied. Graphs and histograms are presented of the total charge collected as well as the charge collected in each observed ion mass group. Data show that ion signals consist primarily of the lower ionization potential elements over the 1 - 8 km/s range.

Roy, N. L.↗
NASA NTRS1987

Evaluation of flow topology from numerical data

Results obtained from numerical calculations and modern (optical) diagnostics are often too complicated for manual inspection, manipulation and display. A simpler but still accurate description of these results is needed to facilitate data understanding. The paper discusses preliminary investigations into methods for the decomposition of 2-D and 3-D fluid flow data bases into elementary structures for purposes of description, analysis and comparison. An approach which involves the development of scene-like representation of the flow topology is presented. Using features such as critical points and dividing streamlines as a basis, a representation of the global topology of the flow is generated. The topology is then represented by a graph with the various structures represented by the nodes and their relationships in the flow by the connecting lines of the graph. Once the flow field has been placed in this form, it can be studied and compared with other data sets using techniques of syntactic pattern recognition or displayed using 3-D graphics techniques.

Hesselink, Lambertus↗
NASA NTRS1988

The computation of non-equilibrium chemically-reacting flows

Numerical techniques for the analysis of flows with nonequilibrium thermodynamics and chemistry are developed and demonstrated. Particular attention is given to the formulation of the thermodynamic and chemical gas models, the derivation of the governing equations, and the solution procedures. Results for typical problems involving shock tubes and supersonic diffusers are presented in extensive graphs and briefly characterized.

Grossman, B.↗
NASA NTRS2004

Effects of Heat Flux, Oxygen Concentration and Glass Fiber Volume Fraction on Pyrolysate Mass Flux from Composite Solids

Experimental work on the effects of heat flux, oxygen concentration and glass fiber volume fraction on pyrolysate mass flux from samples of polypropylene/glass fiber composite (PP/G) is underway. The research is conducted as part of a larger project to develop a test methodology for flammability of materials, particularly composites, in the microgravity and variable oxygen concentration environment of spacecraft and space structures. Samples of PP/G sized at 30x30x10 mm are flush mounted in a flow tunnel, which provides a flow of oxidizer over the surface of the samples at a fixed value of 1 m/s and oxygen concentrations varying between 18 and 30%. Each sample is exposed to a constant external radiant heat flux at a given value, which varies between tests from 10 to 24 kW/m2. Continuous sample mass loss and surface temperature measurements are recorded for each test. Some tests are conducted with an igniter and some are not. In the former case, the research goal is to quantify the critical mass flux at ignition for the various environmental and material conditions described above. The later case generates a wider range of mass flux rates than those seen prior to ignition, providing an opportunity to examine the protective effects of blowing on oxidative pyrolysis and heating of the surface. Graphs of surface temperature and sample mass loss vs. time for samples of 30% PPG at oxygen concentrations of 18 and 21% are presented in the figures below. These figures give a clear indication of the lower pyrolysis rate and extended time to ignition that accompany a lower oxygen concentration. Analysis of the mass flux rate at the time of ignition gives good repeatability but requires further work to provide a clear indication of mass flux trends accompanying changes in environmental and material properties.

Rich, D. B.↗
NASA NTRS2004

Effects of Heat Flux, Oxygen Concentration and Glass Fiber Volume Fraction on Pyrolysate Mass Flux from Composite Solids

Experimental work on the effects of heat flux, oxygen concentration and glass fiber volume fraction on pyrolysate mass flux from samples of polypropylene/glass fiber composite (PP/G) is underway. The research is conducted as part of a larger project to develop a test methodology for flammability of materials, particularly composites, in the microgravity and variable oxygen concentration environment of spacecraft and space structures. Samples of PP/G sized at 30 x 30 x 10 mm are flush mounted in a flow tunnel, which provides a flow of oxidizer over the surface of the samples at a fixed value of 1 m/s and oxygen concentrations varying between 18 and 30%. Each sample is exposed to a constant external radiant heat flux at a given value, which varies between tests from 10 to 24 kW/sq m. Continuous sample mass loss and surface temperature measurements are recorded for each test. Some tests are conducted with an igniter and some are not. In the former case, the research goal is to quantify the critical mass flux at ignition for the various environmental and material conditions described above. The later case generates a wider range of mass flux rates than those seen prior to ignition, providing an opportunity to examine the protective effects of blowing on oxidative pyrolysis and heating of the surface. Graphs of surface temperature and sample mass loss vs. time for samples of 30% PPG at oxygen concentrations of 18 and 21% are presented in the figures below. These figures give a clear indication of the lower pyrolysis rate and extended time to ignition that accompany a lower oxygen concentration. Analysis of the mass flux rate at the time of ignition gives good repeatability but requires further work to provide a clear indication of mass flux trends accompanying changes in environmental and material properties.

Rich, D. B.↗
NASA NTRS2004

Automated Processing of ISIS Topside Ionograms into Electron Density Profiles

Modeling of the topside ionosphere has for the most part relied on just a few years of data from topside sounder satellites. The widely used Bent et al. (1972) model, for example, is based on only 50,000 Alouette 1 profiles. The International Reference Ionosphere (IRI) (Bilitza, 1990, 2001) uses an analytical description of the graphs and tables provided by Bent et al. (1972). The Alouette 1, 2 and ISIS 1, 2 topside sounder satellites of the sixties and seventies were ahead of their times in terms of the sheer volume of data obtained and in terms of the computer and software requirements for data analysis. As a result, only a small percentage of the collected topside ionograms was converted into electron density profiles. Recently, a NASA-funded data restoration project has undertaken and is continuing the process of digitizing the Alouette/ISIS ionograms from the analog 7-track tapes. Our project involves the automated processing of these digital ionograms into electron density profiles. The project accomplished a set of important goals that will have a major impact on understanding and modeling of the topside ionosphere: (1) The TOPside Ionogram Scaling and True height inversion (TOPIST) software was developed for the automated scaling and inversion of topside ionograms. (2) The TOPIST software was applied to the over 300,000 ISIS-2 topside ionograms that had been digitized in the fkamework of a separate AISRP project (PI: R.F. Benson). (3) The new TOPIST-produced database of global electron density profiles for the topside ionosphere were made publicly available through NASA s National Space Science Data Center (NSSDC) ftp archive at . (4) Earlier Alouette 1,2 and ISIS 1, 2 data sets of electron density profiles from manual scaling of selected sets of ionograms were converted fiom a highly-compressed binary format into a user-friendly ASCII format and made publicly available through nssdcftp.gsfc.nasa.gov. The new database for the topside ionosphere established as a result of this project, has stimulated a multitude of new studies directed towards a better description and prediction of the topside ionosphere. Marinov et al. (2004) developed a new model for the upper ion transition height (Oxygen to Hydrogen and Helium) and Bilitza (2004) deduced a correction term for the I N topside electron density model. Kutiev et al. (2005) used this data to develop a new model for the topside ionosphere scale height (TISH) as a function of month, local time, latitude, longitude and solar flux F10.7. Comparisons by Belehaki et al. (2005) show that TISH is in general agreement with scale heights deduced from ground ionosondes but the model predicts post-midnight and afternoon maxima whereas the ionosonde data show a noon maximum. Webb and Benson (2005) reported on their effort to deduce changes in the plasma temperature and ion composition from changes in the topside electron density profile as recorded by topside sounders. Limitations and possible improvements of the IRI topside model were discussed by Coisson et al. (2005) including also the possible use of the NeQuick model, Our project progressed in close collaboration and coordination with the GSFC team involved in the ISIS digitization effort. The digitization project was highly successful producing a large amount of digital topside ionograms. Several no-cost extensions of the TOPIST project were necessary to keep up with the pace and volume of the digitization effort.

Reinisch, bodo W.↗