Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “friction-”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Measurement of Gear Tooth Dynamic Friction

Measurements of dynamic friction forces at the gear tooth contact were undertaken using strain gages at the root fillets of two successive teeth. Results are presented from two gear sets over a range of speeds and loads. The results demonstrate that the friction coefficient does not appear to be significantly influenced by the sliding reversal at the pitch point, and that the friction coefficient values found are in accord with those in general use. The friction coefficient was found to increase at low sliding speeds. This agrees with the results of disc machine testing.

GEAR TEETH↗

Protocol Dependent Frictional Granular Jamming Simulations: Cyclical, Compression and Expansion

Granular matter takes many paths to pack in natural and industrial processes. The path influences the packing microstructure, particularly for frictional grains. We perform discrete element modeling simulations of different paths to construct packings of frictional spheres. Specifically, we explore four stress-controlled protocols implementing packing expansions and compressions in various combinations thereof. We characterize the eventual packed states through their dependence of the packing fraction and coordination number on packing pressure, identifying non-monotonicities with pressure that correlate with the fraction of frictional contacts. These stress-controlled, bulk-like particle simulations access very low-pressure packings, namely, the marginally stable limit, and demonstrate the strong protocol dependence of frictional granular matter.

DEM↗

Effect of flow topology on the calculation of two-phase frictional multipliers in uniformly heated flow of R-134a in a rectangular duct

The two-phase frictional multipliers for SUVA R-134a flowing in a rectangular duct (with D{sub H} = 4.8 mm) have been measured for three nominal system pressures (0.88, 1.34 and 2.34 MPa) and four nominal mass fluxes (510, 1020 and 1740, 2040 kg/m{sup 2}/s) under uniform heat flux conditions. The data is compared with adiabatic data previously taken at similar flow conditions, as well as with several classical multiplier correlations. The comparisons reveal a strong effect of pressure and mass flux on the flow topology and, by extension, a large effect on the calculation of acceleration and frictional pressure drop components. For this fluid and this geometry, entrainment and fluid separation is enhanced at higher pressures and mass flux such that most of the liquid exists in the test section edges and as dispersed droplets in the core. For these cases, the classical simplified approach to calculate acceleration pressure drop fails to adequately predict the acceleration component and leads to erroneous calculations of frictional pressure drop from the measured total pressure drop. Best estimates of the true acceleration component are given, based on void profiles measured with a gamma densitometer system, comparisons to the adiabatic data, and recasting the data in terms of the total pressure drop multiplier as a function of the Martinelli parameter, X{sub tt}. (author)

42 ENGINEERING↗

Two-sided friction stir riveting by extrusion: A process for joining dissimilar materials

Two-sided friction stir riveting (FSR) by extrusion is an innovative process developed to rapidly, efficiently, and securely join dissimilar materials. This process extends a previously developed one sided friction stir extrusion process to create a strong and robust joint by producing a continuous, rivet-like structure through a preformed hole in one of the materials with a simultaneous, two-sided friction stir spot weld. The two-sided FSR by extrusion process securely joins the dissimilar materials together and effectively locks them in place without the use of any separate materials or fasteners. Lastly, in this paper we demonstrate the process by joining aluminum to steel and illustrate its potential application to automotive and aerospace manufacturing processes.

36 MATERIALS SCIENCE↗

Tribological behavior prediction of friction materials for ultrasonic motors using Monte Carlo‐based artificial neural network

ABSTRACT In this article, the relationship of complexity, diversity, and uncertainty between components and tribological properties of friction materials based on a Monte Carlo‐based artificial neural network (MC‐ANN) model was predicted precisely. Meanwhile, the grey relational analysis was applied to figure out weight of factors, optimize formulation design, and calculate nonlinear dependency of ingredients. The accuracy of model was studied by comparing experimental and simulated values on the basis of statistical methods (root‐mean‐squared error). It was found that the model exhibited an excellent performance in predicting and fitting effect. Moreover, comprehensive analysis of weight indicated that nano‐SiO 2 and mica exerted a significant role in improving the friction stability and wear resistance. According to different contents of each ingredient, the corresponding friction coefficient and specific wear rate could be obtained by virtue of a well‐trained MC‐ANN model without experiments, which saved a lot of time and money. It can be expected that the results of this work will extend the current research and pave a route for further in‐depth studies of friction materials. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136 , 47157.

Li, Song↗

Parametric Modeling of AZ31-Mg Alloy Friction Stir Weld Temperature Histories

A parametric model of friction stir weld temperature histories is presented that uses constraint conditions, which are three-dimensional isothermal boundary conditions on the calculated temperature fields. This study describes further extension, with respect to formulation, of a parametric-modeling methodology, which is relatively optimal in terms of representation for application to friction stir welding and processing. These parametric representations of temperature histories can be used for modeling friction stir welds whose process conditions are similar to those in this study. Calculations of AZ31-Mg alloy friction stir weld temperature histories are presented, which use temperature-field constraint conditions based on measured weld cross sections and a model for the estimation of weld stir zone temperatures.

36 MATERIALS SCIENCE↗

Investigation of the influence of frictional viscosity regularization on quasi-static gas-solid flow predictions in a conical spouted bed with non-porous draft tube

The stress in the quasi-static particle flow is often modeled through the Mohr-Coulomb failure criterion. In the extension to complex three-dimensional flows, a granular viscosity is introduced through a tensorial rheology and the deviatoric frictional stress tensor is assumed aligned with the strain rate tensor. This granular viscosity is singular as the shear rate approaches zero, regardless of the local rheology. We discuss the influence of regularizing such a frictional viscosity on the particle circulation rate and other measured characteristics in a laboratory scale draft tube spouted bed. Here, the friction between particles is modeled either with a constant Coulomb rheology or using a local particle pressure and strain-rate based friction known as μ ( I )-rheology. The predictions appear very dependent on the regularization parameter introduced by the method. The mean properties of the flow (e.g. circulation and pressure drop) monotonically converge towards the measurements when the regularization parameter tends to zero. In other respects, the two regularization models regarded in this study induced similar hydrodynamics within the spouted bed of interest. But the analysis of the conditional averages of the inertial number and the fraction of the solids in the quasi-static regime shows that the extent and staticity of the quasi-static region is sensitive to changes to the regularization parameter or regularization function.

36 MATERIALS SCIENCE↗

Lateral bearing capacity of hybrid monopile-friction wheel foundation for offshore wind turbines by centrifuge modelling

The hybrid monopile-friction wheel foundation is an innovative alternative for offshore wind turbines. The concept has wider adaptability and can be used as reinforcement method for existing monopiles. A series of centrifuge tests was performed to investigate the lateral bearing capacities of the hybrid foundation under monotonic loads. Five foundation models and two soil types were considered. According to the recorded responses, the hybrid foundation demonstrated better lateral behaviors that both lateral bearing capacity and stiffness are enhanced. Two analytical methods were proposed and compared with the centrifuge test results. The bearing capacity of the hybrid foundation is smaller than the sum of individual pile and friction wheel, and a reduction factor is suggested for both friction wheels. The friction wheel restrains rotations of monopile and provides extra restoring moments; their effects are idealized as equivalent moments acting on the pile head. The analytical results provide possible solutions in estimating the lateral bearing capacity of the innovative hybrid foundation system for offshore wind turbines by using traditional theories.

17 WIND ENERGY↗

Friction behavior of a multi-interface system and improved performance by AlMgB 14 –TiB 2 –C and diamond-like-carbon coatings

We investigated friction behavior of a bearing system with two interfaces involved: a roller component experiencing rolling–sliding interaction against twin cylinders under point contacts while simultaneously undergoing pure sliding interaction against a socket under a conformal contact. Lubrication modeling predicted a strong correlation between the roller's rolling condition and the system's friction behavior. Experimental observations first validated the analytical predictions using steel and iron components. Diamond-like-carbon (DLC) coating and AlMgB 14 –TiB 2 coating with a carbon topcoat (BAMC) were then applied to the roller and twin cylinders, respectively. In conclusion, testing and analysis results suggest that the coatings effectively decreased the slip ratio for the roller–cylinder contact and the sliding friction at both bearing interfaces and, as a result, significantly reduced the system frictional torque.

42 ENGINEERING↗

On the enhancement of boundary layer skin friction by turbulence: an angular momentum approach

Turbulence enhances the wall shear stress in boundary layers, significantly increasing the drag on streamlined bodies. Other flow features such as free stream pressure gradients and streamwise boundary layer growth also strongly influence the local skin friction. In this paper, an angular momentum integral (AMI) equation is introduced to quantify these effects by representing them as torques that alter the shape of the mean velocity profile. This approach uniquely isolates the skin friction of a Blasius boundary layer in a single term that depends only on the Reynolds number most relevant to the flow's engineering context, so that other torques are interpreted as augmentations relative to the laminar case having the same Reynolds number. The AMI equation for external flows shares this key property with the so-called FIK relation for internal flows (Fukagata et al. , Phys. Fluids , vol. 14, 2002, pp. L73–L76). Without a geometrically imposed boundary layer thickness, the length scale in the Reynolds number for the AMI equation may be chosen freely. After a brief demonstration using Falkner–Skan boundary layers, the AMI equation is applied as a diagnostic tool on four transitional and turbulent boundary layer direct numerical simulation datasets. Regions of negative wall-normal velocity are shown to play a key role in limiting the peak skin friction during the late stages of transition, and the relative strengths of terms in the AMI equation become independent of the transition mechanism a very short distance into the fully turbulent regime. The AMI equation establishes an intuitive, extensible framework for interpreting the impact of turbulence and flow control strategies on boundary layer skin friction.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Friction and Adhesion Forces of Bacillus thuringiensis Spores on Planar Surfaces in Atmospheric Systems

The kinetic friction force and the adhesion force of Bacillus thuringiensis spores on planar surfaces in atmospheric systems were studied using atomic force microscopy. The influence of relative humidity (RH) on these forces varied for different surface properties including hydrophobicity, roughness, and surface charge. The friction force of the spore was greater on a rougher surface than on mica, which is atomically flat. As RH increases, the friction force of the spores decreases on mica whereas it increases on rough surfaces. The influence of RH on the interaction forces between hydrophobic surfaces is not as strong as for hydrophilic surfaces. The friction force of the spore is linear to the sum of the adhesion force and normal load on the hydrophobic surface. In conclusion, the poorly defined surface structure of the spore and the adsorption of contaminants from the surrounding atmosphere are believed to cause a discrepancy between the calculated and measured adhesion forces.

59 BASIC BIOLOGICAL SCIENCES↗

Transient evolution of permeability and friction in a slowly slipping fault activated by fluid pressurization

The mechanisms of permeability and friction evolution in a natural fault are investigated in situ. During three fluid injection experiments at different places in a fault zone, we measured simultaneously the fluid pressure, fault displacements and seismic activity. Changes in fault permeability and friction are then estimated concurrently. Results show that fault permeability increases up to 1.58 order of magnitude as a result of reducing effective normal stress and cumulative dilatant slip, and 19-to-60.8% of the enhancement occurs without seismic emissions. When modeling the fault displacement, we found that a rate-and-state friction and a permeability dependent on both slip and slip velocity together reasonably fit the fault-parallel and fault-normal displacements. This leads to the conclusion that the transient evolution of fault permeability and friction caused by a pressure perturbation exerts a potentially dominant control on fault stability during fluid flow.

58 GEOSCIENCES↗

Relation between interfacial shear and friction force in 2D materials

Understanding the interfacial properties between an atomic layer and its substrate is of key interest at both the fundamental and technological levels. From Fermi level pinning to strain engineering and superlubricity, the interaction between a single atomic layer and its substrate governs electronic, mechanical and chemical properties. Here, we measure the hardly accessible interfacial transverse shear modulus of an atomic layer on a substrate. By performing measurements on bulk graphite, and on epitaxial graphene films on SiC with different stacking orders and twisting, as well as in the presence of intercalated hydrogen, we find that the interfacial transverse shear modulus is critically controlled by the stacking order and the atomic layer–substrate interaction. Importantly, we demonstrate that this modulus is a pivotal measurable property to control and predict sliding friction in supported two-dimensional materials. The experiments demonstrate a reciprocal relationship between friction force per unit contact area and interfacial shear modulus. As a result, the same relationship emerges from simulations with simple friction models, where the atomic layer– substrate interaction controls the shear stiffness and therefore the resulting friction dissipation.

36 MATERIALS SCIENCE↗

Enhancement of oil flow in shale nanopores by manipulating friction and viscosity

We report that understanding the viscosity and friction of a fluid under nanoconfinement is the key to nanofluidics research. Existing work on nanochannel flow enhancement has been focused on simple systems with only one to two fluids considered such as water flow in carbon nanotubes, and large slip lengths have been found to be the main factor for the massive flow enhancement. In this study, we use molecular dynamics simulations to study the fluid flow of a ternary mixture of octane–carbon dioxide–water confined within two muscovite and kerogen surfaces. The results indicate that, in a muscovite slit, supercritical CO 2 (scCO 2 ) and H 2 O both enhance the flow of octane due to (i) a decrease in the friction of octane with the muscovite wall because of the formation of thin layers of H 2 O and scCO 2 near the surfaces; and (ii) a reduction in the viscosity of octane in nanoconfinement. Water reduces octane viscosity by weakening the interaction of octane with the muscovite surface, while scCO 2 reduces octane viscosity by weakening both octane–octane and octane–surface interactions. In a kerogen slit, water does not play any significant role in changing the friction or viscosity of octane. In contrast, scCO 2 reduces both the friction and the viscosity of octane, and the enhancement of octane flow is mainly caused by the reduction of viscosity. In conclusion, our results highlight the importance of multicomponent interactions in nanoscale fluid transport. The results presented here also have a direct implication in enhanced oil recovery in unconventional reservoirs.

58 GEOSCIENCES↗

A many-body states picture of electronic friction: The case of multiple orbitals and multiple electronic states

We present a very general form of electronic friction as present when a molecule with multiple orbitals hybridizes with a metal electrode. To develop this picture of friction, we embed the quantum-classical Liouville equation (QCLE) within a classical master equation (CME). Thus, this article extends our previous work analyzing the case of one electronic level, as we may now treat the case of multiple levels and many electronic molecular states. We show that, in the adiabatic limit, where electron transitions are much faster than nuclear motion, the QCLE-CME reduces to a Fokker-Planck equation, such that nuclei feel an average force as well as friction and a random force—as caused by their interaction with the metallic electrons. Finally, we show numerically and analytically that our frictional results agree with other published results calculated using non-equilibrium Green’s functions. Numerical recipes for solving this QCLE-CME will be provided in a subsequent paper.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Superlubricity: Friction’s vanishing act

Friction and wear affect almost all moving mechanical systems. By some estimates, nearly a quarter of the world's energy output is spent in overcoming friction.(1) About 70% of equipment failures are in some way attributable to wear and fatigue. Granted, strong friction forces are sometimes needed; brakes, tires, and continuously variable transmissions, for example, couldn't operate without them. But in many cases, alleviating friction would save energy, help the environment, and boost productivity.

74 ATOMIC AND MOLECULAR PHYSICS↗

Aluminium composites prepared by laser cladding assisted by friction stir processing

Abstract A laser cladding and friction stir processing hybrid method was employed to produce an Al matrix composite layer. The microstructure, phase composition, microhardness and conductivity of the composites were investigated. A laser cladding layer with a thickness of approximately 200 μ m was prepared on a 1060 aluminium plate and it was broken up and distributed on the Al matrix after friction stir processing. The particle/Al interfaces exhibited extremely good interfacial integrity. Microstructural observations revealed that an obvious in situ reaction occurred at the particle/Al interfaces, which effectively improved the bonding between the reinforcement phase and the matrix. TEM analysis and selected area diffraction enabled the identification of the intermetallic compounds and confirmed them to be Al 5 Fe 2 and Al 3 Fe. The average microhardness values of the friction stir processed composites reached approximately 85 HV. The electrical resistivity of the friction stir processed composites is slightly higher than that of the aluminium matrix.

Wei, Yanni (ORCID:0000000244443642)↗

Spatial dispersion in atom-surface quantum friction

We investigate the influence of spatial dispersion on atom-surface quantum friction. We show that for atom-surface separations shorter than the carrier's mean free path within the material, the frictional force can be several orders of magnitude larger than that predicted by local optics. In addition, when taking into account spatial dispersion effects, we show that the commonly used local thermal equilibrium approximation underestimates by approximately 95% the drag force, obtained by employing the recently reported nonequilibrium fluctuation-dissipation relation for quantum friction. Unlike the treatment based on local optics, spatial dispersion in conjunction with corrections to local thermal equilibrium change not only the magnitude but also the distance scaling of quantum friction.

36 MATERIALS SCIENCE↗