Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fiber composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Manufacturing of Nanocomposite Carbon Fibers and Composite Cylinders

Pitch-based nanocomposite carbon fibers were prepared with various percentages of carbon nanofibers (CNFs), and the fibers were used for manufacturing composite structures. Experimental results show that these nanocomposite carbon fibers exhibit improved structural and electrical conductivity properties as compared to unreinforced carbon fibers. Composite panels fabricated from these nanocomposite carbon fibers and an epoxy system also show the same properties transformed from the fibers. Single-fiber testing per ASTM C1557 standard indicates that the nanocomposite carbon fiber has a tensile modulus of 110% higher, and a tensile strength 17.7% times higher, than the conventional carbon fiber manufactured from pitch. Also, the electrical resistance of the carbon fiber carbonized at 900 C was reduced from 4.8 to 2.2 ohm/cm. The manufacturing of the nanocomposite carbon fiber was based on an extrusion, non-solvent process. The precursor fibers were then carbonized and graphitized. The resultant fibers are continuous.

Tan, Seng↗
NASA NTRS1992

The optimal fiber volume fraction and fiber-matrix property compatibility in fiber reinforced composites

Although the question of minimum or critical fiber volume fraction beyond which a composite can then be strengthened due to addition of fibers has been dealt with by several investigators for both continuous and short fiber composites, a study of maximum or optimal fiber volume fraction at which the composite reaches its highest strength has not been reported yet. The present analysis has investigated this issue for short fiber case based on the well-known shear lag (the elastic stress transfer) theory as the first step. Using the relationships obtained, the minimum spacing between fibers is determined upon which the maximum fiber volume fraction can be calculated, depending on the fiber packing forms within the composites. The effects on the value of this maximum fiber volume fraction due to such factors as fiber and matrix properties, fiber aspect ratio and fiber packing forms are discussed. Furthermore, combined with the previous analysis on the minimum fiber volume fraction, this maximum fiber volume fraction can be used to examine the property compatibility of fiber and matrix in forming a composite. This is deemed to be useful for composite design. Finally some examples are provided to illustrate the results.

Pan, Ning↗
NASA NTRS1983

The mechanics of delamination in fiber-reinforced composite materials. Part 2: Delamination behavior and fracture mechanics parameters

Based on theories of laminate anisotropic elasticity and interlaminar fracture, the complete solution structure associated with a composite delamination is determined. Fracture mechanics parameters characterizing the interlaminar crack behavior are defined from asymptotic stress solutions for delaminations with different crack-tip deformation configurations. A numerical method employing singular finite elements is developed to study delaminations in fiber composites with any arbitrary combinations of lamination, material, geometric, and crack variables. The special finite elements include the exact delamination stress singularity in its formulation. The method is shown to be computationally accurate and efficient, and operationally simple. To illustrate the basic nature of composite delamination, solutions are shown for edge-delaminated (0/-0/-0/0) and (+ or - 0/+ or - 0/90/90 deg) graphite-epoxy systems under uniform axial extenstion. Three-dimensional crack-tip stress intensity factors, associated energy release rates, and delamination crack-closure are determined for each individual case. The basic mechanics and mechanisms of composite delamination are studied, and fundamental characteristics unique to recently proposed tests for interlaminar fracture toughness of fiber composite laminates are examined.

Wang, S. S.↗
NASA NTRS1983

The mechanics of delamination in fiber-reinforced composite materials. II - The delamination behavior and fracture mechanics parameters

Based on theories of laminate anisotropic elasticity and interlaminar fracture, the complete solution structure associated with a composite delamination is determined. Fracture mechanics parameters characterizing the interlaminar crack behavior are defined from asymptotic stress solutions for delaminations with different crack-tip deformation configurations. A numerical method employing singular finite elements is developed to study delaminations in fiber composites with any arbitrary combinations of lamination, material, geometric, and crack variables. The special finite elements include the exact delamination stress singularity in its formulation. The method is shown to be computationally accurate and efficient, and operationally simple. To illustrate the basic nature of composite delamination, solutions are shown for edge-delaminated (0/-0/-0/0) and (+ or - 0/+ or - 0/90/90 deg) graphite-epoxy systems under uniform axial extension. Three-dimensional crack-tip stress intensity factors, associated energy release rates, and delamination crack-closure are determined for each individual case. The basic mechanics and mechanisms of composite delamination are studied, and fundamental characteristics unique to recently proposed tests for interlaminar fracture toughness of fiber composite laminates are examined. Previously announced in STAR as N84-13222

Wang, S. S.↗
NASA NTRS1980

Effect of High Energy Radiation on Mechanical Properties of Graphite Fiber Reinforced Composites

The flexural strength and average modulus of graphite fiber reinforced composites were tested before and after exposure to 0.5 Mev electron radiation and 1.33 Mev gamma radiation by using a three point bending test (ASTM D-790). The irradiation was conducted on vacuum treated samples. Graphite fiber/epoxy (T300/5208), graphite fiber/polyimide (C6000/PMR 15) and graphite fiber/polysulfone (C6000/P1700) composites after being irradiated with 0.5 Mev electron radiation in vacuum up to 5000 Mrad, show increases in stress and modulus of approximately 12% compared with the controls. Graphite fiber/epoxy (T300/5208 and AS/3501-6), after being irradiated with 1.33 Mev gamma radiation up to 360 Mrads, show increases in stress and modulus of approximately 6% at 167 Mrad compared with the controls. Results suggest that the graphite fiber composites studied should withstand the high energy radiation in a space environment for a considerable time, e.g., over 30 years.

Naranong, N.↗
NASA NTRS1987

The effect of bromination of carbon fibers on the coefficient of thermal expansion of graphite fiber-epoxy composites

To examine the effect of bromination of carbon fibers on the coefficient of thermal expansion (CTE) of carbon fiber epoxy composites, several pristine and brominated carbon fiber-epoxy composite samples were subjected to thermomechanical analysis. The CTE's of these samples were measured in the uniaxial and transverse directions. The CTE was dominated by the fibers in the uniaxial direction, while it was dominated by the matrix in the transverse directions. Bromination had no effect on the CTE of any of the composites. In addition, the CTE of fiber tow was measured in the absence of a polymer matrix, using an extension probe. The results from this technique were inconclusive.

Jaworske, D. A.↗
NASA NTRS1977

Fibre intersections in a planar randomly oriented fibre composite

The interaction of fibers in a randomly oriented fiber composite is a key factor in determining the mechanical properties of some composites. A theoretical model is presented by means of which values of the mean and the variance of fiber intersections in a planar randomly oriented fiber composite are predicted. These predictions are compared with the mean and variance obtained from a computer simulation of the fiber intersection process.

Williams, J. H., Jr.↗
NASA NTRS1994

Continuous unidirectional fiber reinforced composites: Fabrication and testing

The study of the anisotropic mechanical properties of an inexpensively fabricated composite with continuous unidirectional fibers and a clear matrix was investigated. A method has been developed to fabricate these composites with aluminum fibers and a polymer matrix. These composites clearly demonstrate the properties of unidirectional composites and cost less than five dollars each to fabricate.

Weber, M. D.↗
NASA NTRS1976

Fundamental analysis of the failure of polymer-based fiber reinforced composites

A mathematical model is described which will permit predictions of the strength of fiber reinforced composites containing known flaws to be made from the basic properties of their constituents. The approach was to embed a local heterogeneous region (LHR) surrounding the crack tip into an anisotropic elastic continuum. The model should (1) permit an explicit analysis of the micromechanical processes involved in the fracture process, and (2) remain simple enough to be useful in practical computations. Computations for arbitrary flaw size and orientation under arbitrary applied load combinations were performed from unidirectional composites with linear elastic-brittle constituent behavior. The mechanical properties were nominally those of graphite epoxy. With the rupture properties arbitrarily varied to test the capability of the model to reflect real fracture modes in fiber composites, it was shown that fiber breakage, matrix crazing, crack bridging, matrix-fiber debonding, and axial splitting can all occur during a period of (gradually) increasing load prior to catastrophic fracture. The computations reveal qualitatively the sequential nature of the stable crack process that precedes fracture.

Kanninen, M. F.↗
NASA NTRSDate not supplied

Artificial Generation of 2-D Fiber Reinforced Composite Microstructures with Statistically Equivalent Features

Fiber reinforced composites are used widely for their high strength and low weight advantages in various aerospace and automotive applications. While their use may be sought after, modeling of these material requires increasing fidelity at the lower scales to capture accurate material behavior under loading. The first steps in creating statistically equivalent models to real life cases is developing a method of rapid evaluation and artificial microstructure generation. The outlined work is capable of tracking microscale fiber positions and determining regions of localized volume fraction extrema (high and low end). Groupings of high and low volume fraction regions are called clusters and their geometry is used to characterize the microstructure. These cluster features can be evaluated for both artificial models and actual scans, allowing correlation to be established which can ultimately be used to regenerate statistically equivalent models. The results of this work show that if one feature is to be correlated, a model can be generated which matches almost exactly. But once more features are equally taken into account, the regeneration loses accuracy.

micromechanics↗
NASA NTRS2016

Multifunctional Hybrid Carbon Nanotube/Carbon Fiber Polymer Composites

For aircraft primary structures, carbon fiber reinforced polymer (CFRP) composites possess many advantages over conventional aluminum alloys due to their light weight, higher strengthand stiffness-to-weight ratio, and low life-cycle maintenance costs. However, the relatively low electrical and thermal conductivities of CFRP composites fail to provide structural safety in certain operational conditions such as lightning strikes. Despite several attempts to solve these issues with the addition of carbon nanotubes (CNT) into polymer matrices, and/or by interleaving CNT sheets between conventional carbon fiber (CF) composite layers, there are still interfacial problems that exist between CNTs (or CF) and the resin. In this study, hybrid CNT/CF polymer composites were fabricated by interleaving layers of CNT sheets with Hexcel® IM7/8852 prepreg. Resin concentrations from 1 wt% to 50 wt% were used to infuse the CNT sheets prior to composite fabrication. The interlaminar properties of the resulting hybrid composites were characterized by mode I and II fracture toughness testing (double cantilever beam and end-notched flexure test). Fractographical analysis was performed to study the effect of resin concentration. In addition, multi-directional physical properties like thermal conductivity of the orthotropic hybrid polymer composite were evaluated. Interleaving CNT sheets significantly improved the in-plane (axial and perpendicular direction of CF alignment) thermal conductivity of the hybrid composite laminates by 50 - 400%.

Kang, Jin Ho↗
NASA NTRS1973

Feasibility of producing cast-refractory metal-fiber superalloy composites

A study was conducted to evaluate the feasibility of direct casting as a practical method for producing cast superalloy tungsten or columbium alloy fiber composites while retaining a high percentage of fiber strength. Fourteen nickel base, four cobalt, and three iron based matrices were surveyed for their degree of reaction with the metal fibers. Some stress-rupture results were obtained at temperatures of 760, 816, 871, and 1093 C for a few composite systems. The feasibility of producing acceptable composites of some cast nickel, cobalt, and iron matrix alloys with tungsten or columbium alloy fibers was demonstrated.

Mcintyre, R. D.↗
NASA NTRS1981

Spectroscopic determination of the in-situ composition of epoxy matrices in glass-fiber-reinforced composites

Computerized infrared analysis is applied to the characterization of a glass-reinforced crosslinked polyester. The method of factor analysis determines the number of independent components which constitute the polymeric matrix. Subsequently, the spectra of those components are fitted by a least-squares criterion to spectra of the multicomponent matrix, or, if the glass spectrum is included as an additional component, to the spectra of composites. The least-squares coefficients yield the matrix composition in terms of the initial reactant composition and the extent of crosslinking.

Antoon, M. K.↗
NASA NTRSDate not supplied

Modeling the Stochastic Response of Fiber Reinforced Composites with Varied Representative Volume Element Sizes

Fiber reinforced composites are desirable in applications where low weight and high strength are needed, but are susceptible to variability and flaws during manufacturing, making failure predictions difficult. These flaws may occur at the microscale where mechanical properties vary locally due to regions of fiber clusters and matrix pockets. In this study, a multiscale approach was taken to model 3-point bend, 4-point bend, and tensile experiments of a unidirectional composite from only having microstructure scans of these samples and constituent properties from literature. These scans were sampled with different sized windows, and statistically equivalent microstructures were generated, then simulated for stiffness, strength, and fracture toughness using a reduced order micromechanical model and NASA’s Multiscale Analysis Tool (NASMAT). Mesoscale models were created with equivalent element sizes to microstructures and properties sampled from microscale simulation results. Results showed how microscale size affects certain mechanical properties. Also shown is how well mesoscale models agree to experiments when using stochastic element properties and varying element size.

microstructure↗
NASA NTRS1983

The mechanics of delamination in fiber-reinforced composite materials. I - Stress singularities and solution structure

The fundamental mechanics of delamination in fiber composite laminates is studied. Mathematical formulation of the problem is based on laminate anisotropic elasticity theory and interlaminar fracture mechanics concepts. Stress singularities and complete solution structures associated with general composite delaminations are determined. For a fully open delamination with traction-free surfaces, oscillatory stress singularities always appear, leading to physically inadmissible field solutions. A refined model is introduced by considering a partially closed delamination with crack surfaces in finite-length contact. Stress singularities associated with a partially closed delamination having frictional crack-surface contact are determined, and are found to be different from the inverse square-root one of the frictionless-contact case. In the case of a delamination with very small area of crack closure, a simplified model having a square-root stress singularity is employed by taking the limit of the partially closed delamination. The possible presence of logarithmic-type stress singularity is examined; no logarithmic singularity of any kind is found in the composite delamination problem. Numerical examples of dominant stress singularities are shown for delaminations having crack-tip closure with different frictional coefficients between general (1) and (2) graphite-epoxy composites. Previously announced in STAR as N84-13221

Wang, S. S.↗