Results for “failure analysis” — Page 20

NASA NTRS2004

Managing Risk to Ensure a Successful Cassini/Huygens Saturn Orbit Insertion (SOI)

I. Design: a) S/C designed to be largely single fault tolerant; b) Operate in flight demonstrated envelope, with margin; and c) Strict compliance with requirements & flight rules. II. Test: a) Baseline, fault & stress testing using flight system testbeds (H/W & S/W); b) In-flight checkout & demos to remove first time events. III. Failure Analysis: a) Critical event driven fault tree analysis; b) Risk mitigation & development of contingencies. IV) Residual Risks: a) Accepted pre-launch waivers to Single Point Failures; b) Unavoidable risks (e.g. natural disaster). V) Mission Assurance: a) Strict process for characterization of variances (ISAs, PFRs & Waivers; b) Full time Mission Assurance Manager reports to Program Manager: 1) Independent assessment of compliance with institutional standards; 2) Oversight & risk assessment of ISAs, PFRs & Waivers etc.; and 3) Risk Management Process facilitator.

risk managment↗

NASA NTRS1974

Compressive strength of fiber reinforced composite materials

Results of an experimental and analytical investigation of the compressive strength of unidirectional boron-epoxy composite material are presented. Observation of fiber coordinates in a boron-epoxy composite indicates that the fibers contain initial curvature. Combined axial compression and torsion tests were conducted on boron-epoxy tubes, and it was shown that the shear modulus is a function of axial compressive stress. An analytical model which includes initial curvature in the fibers and permits an estimate of the effect of curvature on compressive strength is proposed. Two modes of failure which may result from the application of axial compressive stress are analyzed, delamination and shear instability. Based on tests and analysis, failure of boron-epoxy under axial compressive load is due to shear instability.

Davis, J. G., Jr.↗

NASA NTRS1975

Compressive strength of fiber-reinforced composite materials

Results of an experimental and analytical investigation of the compressive strength of unidirectional boron-epoxy composite material are presented. Observation of fiber coordinates in a boron-epoxy composite indicates that the fibers contain initial curvature. Combined axial compression and torsion tests were conducted on boron-epoxy tubes and it was shown that the shear modulus is a function of axial compressive stress. An analytical model which includes initial curvature in the fibers and permits an estimate of the effect of curvature on compressive strength is proposed. Two modes of failure which may result from the application of axial compressive stress are analyzed - delamination and shear instability. Based on tests and analysis, failure of boron-epoxy under axial compressive load is due to shear instability.

Davis, J. G., Jr.↗

NASA NTRS1986

MCC flight operations automation of STS orbiter systems monitoring

The integration of new capabilities into the Mission Control Center at the Johnson Space Center in Houston, Texas in order to improve the data monitoring and analysis of the STS is discussed. User interface application software and systems, such as the flight data file Shuttle mission simulator and failure analysis program, to be utilized for flight operations automation are examined. Consideration is given to task automation, the trend monitoring system, the data retrieval system, and the launch processing system. The development and functions of the Shuttle data analysis system, which is to operate in real time, are described.

Bates, William V., Jr.↗

NASA NTRS2018

Application of PoF Based Virtual Qualification Methods for Reliability Assessment of Mission Critical PCBs

Reliability is the ability of a product to perform the function for which it was intended for a specified period of time (or cycles) for a given set of life cycle conditions. In today's compressed mission development cycles where designing, building and testing the physical models has to occur in a matter of months not years, Projects don't have the luxury of iteratively building and testing those models. Physics of failure (PoF) is an engineering-based approach to reliability that begins with an understanding of materials, processes, physical interactions, degradation and failure mechanisms, as well as identifying failure models. The PoF approach uses modeling and simulation to qualify a design and manufacturing process, with the ultimate intent of eliminating failures early in the design process by addressing the root cause. The physics-of-failure analysis proactively incorporates reliability into the design process by establishing a scientific basis for evaluating new materials, structures and technologies. Virtual physics-of-failure modeling allows engineers to determine if new technological node can be added to an existing system. This presentation will illustrate an application of a PoF based tool during the initial phases of a printed circuit board assembly development and how the NASA GSFC team was able to dynamically study the effects of electronics parts and printed circuit board material configuration changes under simulated thermal and vibrational stresses

Electronics packaging↗

NASA NTRS2018

Application of PoF Based Virtual Qualification Methods for Reliability Assessment of Mission Critical PCBs

Reliability is the ability of a product to perform the function for which it was intended for a specified period of time (or cycles) for a given set of life cycle conditions. In today's compressed mission development cycles where designing, building and testing the physical models has to occur in a matter of months not years, Projects don't have the luxury of iteratively building and testing those models. Physics of failure (PoF) is an engineering-based approach to reliability that begins with an understanding of materials, processes, physical interactions, degradation and failure mechanisms, as well as identifying failure models. The PoF approach uses modeling and simulation to qualify a design and manufacturing process, with the ultimate intent of eliminating failures early in the design process by addressing the root cause. The physics-of-failure analysis proactively incorporates reliability into the design process by establishing a scientific basis for evaluating new materials, structures and technologies. Virtual physics-of-failure modeling allows engineers to determine if new technological node can be added to an existing system. This presentation will illustrate an application of a PoF based tool during the initial phases of a printed circuit board assembly development and how the NASA GSFC team was able to dynamically study the effects of electronics parts and printed circuit board material configuration changes under simulated thermal and vibrational stresses.

Physics of Failure↗

NASA NTRSDate not supplied

Battery Virtual Cell Module Failure Propagation Thermal Analysis

Explore the source record for details and available documents.

Battery failure↗

NASA NTRS1991

Micromechanical analysis of the failure process in ceramic matrix composites

An analysis of the effectiveness of fiber reinforcement in brittle matrix composites is presented. The analytical method allows consideration of discrete fiber distribution and examination of the development of crack growth parameters on the microscale. The problem associated with bridging zone development is addressed here; therefore, the bridging zone is considered to be smaller than the main preexisting crack, and the small scale approach is used. The mechanics of the reinforcement is accurately accounted for in the process zone of a growing crack. Closed form solutions characterizing the initial failure process are presented for linear and nonlinear force-fiber pullout displacement relationships. The implicit exact solution for the extended bridging zone is presented as well.

Rubinstein, Asher A.↗

NASA NTRS1987

Fatigue damage accumulation in various metal matrix composites

The purpose of this paper is to review some of the latest understanding of the fatigue behavior of continuous fiber reinforced metal matrix composites. The emphasis is on the development of an understanding of different fatigue damage mechanisms and why and how they occur. The fatigue failure modes in continuous fiber reinforced metal matrix composites are controlled by the three constituents of the system: fiber, matrix, and fiber/matrix interface. The relative strains to fatigue failure of the fiber and matrix will determine the failure mode. Several examples of matrix, fiber, and self-similar damage growth dominated fatigue damage are given for several metal matrix composite systems. Composite analysis, failure modes, and damage modeling are discussed. Boron/aluminum, silicon-carbide/aluminum, FP/aluminum, and borsic/titanium metal matrix composites are discussed.

Johnson, W. S.↗

NASA NTRS1982

Flat Plate Solar Array Project: Proceedings of the 20th Project Integration Meeting

Progress made by the Flat-Plate Solar Array Project during the period November 1981 to April 1982 is reported. Project analysis and integration, technology research in silicon material, large-area silicon sheet and environmental isolation, cell and module formation, engineering sciences, and module performance and failure analysis are covered.

Mcdonald, R. R.↗

NASA NTRS1999

Electron Microscopy and Image Analysis for Selected Materials

This particular project was completed in collaboration with the metallurgical diagnostics facility. The objective of this research had four major components. First, we required training in the operation of the environmental scanning electron microscope (ESEM) for imaging of selected materials including biological specimens. The types of materials range from cyanobacteria and diatoms to cloth, metals, sand, composites and other materials. Second, to obtain training in surface elemental analysis technology using energy dispersive x-ray (EDX) analysis, and in the preparation of x-ray maps of these same materials. Third, to provide training for the staff of the metallurgical diagnostics and failure analysis team in the area of image processing and image analysis technology using NIH Image software. Finally, we were to assist in the sample preparation, observing, imaging, and elemental analysis for Mr. Richard Hoover, one of NASA MSFC's solar physicists and Marshall's principal scientist for the agency-wide virtual Astrobiology Institute. These materials have been collected from various places around the world including the Fox Tunnel in Alaska, Siberia, Antarctica, ice core samples from near Lake Vostoc, thermal vents in the ocean floor, hot springs and many others. We were successful in our efforts to obtain high quality, high resolution images of various materials including selected biological ones. Surface analyses (EDX) and x-ray maps were easily prepared with this technology. We also discovered and used some applications for NIH Image software in the metallurgical diagnostics facility.

Williams, George↗

NASA NTRS2004

Materials Analysis: A Key to Unlocking the Mystery of the Columbia Tragedy

Materials analyses of key forensic evidence helped unlock the mystery of the loss of space shuttle Columbia that disintegrated February 1, 2003 while returning from a 16-day research mission. Following an intensive four-month recovery effort by federal, state, and local emergency management and law officials, Columbia debris was collected, catalogued, and reassembled at the Kennedy Space Center. Engineers and scientists from the Materials and Processes (M&P) team formed by NASA supported Columbia reconstruction efforts, provided factual data through analysis, and conducted experiments to validate the root cause of the accident. Fracture surfaces and thermal effects of selected airframe debris were assessed, and process flows for both nondestructive and destructive sampling and evaluation of debris were developed. The team also assessed left hand (LH) airframe components that were believed to be associated with a structural breach of Columbia. Analytical data collected by the M&P team showed that a significant thermal event occurred at the left wing leading edge in the proximity of LH reinforced carbon carbon (RCC) panels 8 and 9. The analysis also showed exposure to temperatures in excess of 1,649 C, which would severely degrade the support structure, tiles, and RCC panel materials. The integrated failure analysis of wing leading edge debris and deposits strongly supported the hypothesis that a breach occurred at LH RCC panel 8.

Mayeaux, Brian M.↗

NASA NTRS1991

Variational mechanics analysis of the stresses in microdrop debond specimens

A recently derived variational mechanics analysis of stresses in single-fiber model composites has been applied to the analysis of the stresses in the microdrop debond specimen. The new analysis is more accurate than the commonly applied shear-lag or elastic-plastic analyses. The results from a sample stress state calculation suggest that interfacial failure between the fiber and the microdrop is by mode I or opening mode failure at the beginning of the microdrop. The opening mode failure is caused by a large tensile radial stress at the fiber/matrix interface. Previous analyses of microdrop debond data have been in terms of a shear strength. It is suggested that these analyses misrepresent microdrop debond results and recommend instead a failure analysis based on energy release rate and interfacial fracture toughness. A procedure for calculating the energy release rate for the growth of an interfacial crack is described.

Scheer, Robert J.↗

NASA NTRS1981

The 19th Project Integration Meeting

The Flat-Plate Solar Array Project is described. Project analysis and integration is discussed. Technology research in silicon material, large-area silicon sheet and environmental isolation; cell and module formation; engineering sciences, and module performance and failure analysis. It includes a report on, and copies of visual presentations made at, the 19th Project Integration Meeting held at Pasadena, California, on November 11, 1981.

Mcdonald, R. R.↗

NASA NTRS1982

Environmental isolation task

The failure-analysis process was organized into a more specific set of long-term degradation steps so that material property change can be differentiated from module damage and module failure. Increasing module performance and life are discussed. A polymeric aging computer model is discussed. Early detection of polymer surface reactions due to aging is reported.

Coulbert, C. D.↗

NASA NTRS1986

Automated Rotating-Machinery Analysis

Computer-controlled automatic system processes accelerometer data from rotating machines, producing mathematical description and graphical display of shaft motion. Program saves processing time, readily identifies type of motion (circular, looped, or elliptical), provides annotated assessments to assist in failure analysis, alerts user to look for distinctive characteristics of machinery, and creates informative plots.

Clark, J.↗

NASA NTRS1991

Limit pressure of a circumferentially reinforced SiC/Ti ring

Limit loads under plane stress and plane strain are found for a circumferentially reinforced elastoplastic ring subjected to interior pressure. These are used as bounds on an estimate of the failure pressure of a SiC/Ti test rig that is being fabricated and tested. The ring is to serve as a benchmark against which deformation and failure analysis methods can be assessed. An anisotropic perfect plasticity idealization of the SiC/Ti ring material is made and used in the limit load calculations. An estimate of the failure pressure of the NASA/PW benchmark test ring is given.

Robinson, D. N.↗

NASA NTRS1992

Limit pressure of a circumferentially reinforced SiC/Ti ring

Limit loads under plane stress and plane strain are found for a circumferentially reinforced elastoplastic ring subjected to interior pressure. These are used as bounds on an estimate of the failure pressure of a SiC/Ti test rig that is being fabricated and tested. The ring is to serve as a benchmark against which deformation and failure analysis methods can be assessed. An anisotropic perfect plasticity idealization of the SiC/Ti ring material is made and used in the limit load calculations. An estimate of the failure pressure of the NASA/PW benchmark test ring is given.

Robinson, D. N.↗