Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “expansion techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Detection of severe thunderstorms using short interval geosynchronous satellite data

The potential and limitations of using short interval (3-7 minutes) geosynchronous, infrared data to ascertain thunderstorm intensity, and therefore indirectly detect severe thunderstorms are discussed. Thunderstorms on four case study days were analyzed over selected areas and time periods using SMS/GOES data, and derived satellite based intensity parameters were compared to severe weather reports. Young, growing thunderstorms are intensity rated using the rate of decrease of the satellite observed cloud top minimum equivalent blackbody temperature. Since most storms cannot be observed until they penetrate through the cirrus overcast produced by previous convection, minimum cloud temperature and rate of blackbody temperature isotherm expansion are then used as intensity indicators. Results are presented and problems and limitations of the techniques and the data are examined. In addition, an analysis of cloud top height variations (as viewed by the satellite) in relation to tornado touchdown times and, in a few cases, to mesocyclone formation times is also presented.

Adler, R. F.↗
NASA NTRS1991

Magnetostrictive direct drive motor

Highly magnetostrictive materials such as Tb.3Dy.7Fe2, commercially known as TERFENOL-D, have been used to date in a variety of devices such as high power actuators and linear motors. The larger magnetostriction available in twinned single crystal TERFENOL-D, approx. 2000 ppm at moderate magnetic field strengths, makes possible a new generation of magnetomechanical devices. NASA researchers are studying the potential of this material as the basis for a direct microstepping rotary motor with torque densities on the order of industrial hydraulics and five times greater than that of the most efficient, high power electric motors. Such a motor would be a micro-radian stepper, capable of precision movements and self-braking in the power-off state. Innovative mechanical engineering techniques are juxtaposed on proper magnetic circuit design to reduce losses in structural flexures, inertias, thermal expansions, eddy currents, and magneto-mechanical coupling, thus optimizing motor performance and efficiency. Mathematical models are presented, including magnetic, structural, and both linear and nonlinear dynamic calculations and simulations. In addition, test results on prototypes are presented.

Naik, Dipak↗
NASA NTRS1992

Observations on computational methodologies for use in large-scale, gradient-based, multidisciplinary design

Various computational methodologies relevant to large-scale multidisciplinary gradient-based optimization for engineering systems design problems are examined with emphasis on the situation where one or more discipline responses required by the optimized design procedure involve the solution of a system of nonlinear partial differential equations. Such situations occur when advanced CFD codes are applied in a multidisciplinary procedure for optimizing an aerospace vehicle design. A technique for satisfying the multidisciplinary design requirements for gradient information is presented. The technique is shown to permit some leeway in the CFD algorithms which can be used, an expansion to 3D problems, and straightforward use of other computational methodologies.

Newman, P. A.↗
NASA NTRS2001

Detection of Deforestation and Land Conversion in Rondonia, Brazil Using Change Detection Techniques

Fires associated with tropical deforestation, land conversion, and land use greatly contribute to emissions as well as the depletion of carbon and nutrient pools. The objective of this research was to compare change detection techniques for identifying deforestation and cattle pasture formation during a period of early colonization and agricultural expansion in the vicinity of Jamari, Rond6nia. Multi-date Landsat Thematic Mapper (TM) data between 1984 and 1992 was examined in a 94 370-ha area of active deforestation to map land cover change. The Tasseled Cap (TC) transformation was used to enhance the contrast between forest, cleared areas, and regrowth. TC images were stacked into a composite multi-date TC and used in a principal components (PC) transformation to identify change components. In addition, consecutive TC image pairs were differenced and stacked into a composite multi-date differenced image. A maximum likelihood classification of each image composite was compared for identification of land cover change. The multi-date TC composite classification had the best accuracy of 78.1% (kappa). By 1984, only 5% of the study area had been cleared, but by 1992, 11% of the area had been deforested, primarily for pasture and 7% lost due to hydroelectric dam flooding. Finally, discrimination of pasture versus cultivation was improved due to the ability to detect land under sustained clearing opened to land exhibiting regrowth with infrequent clearing.

Guild, Liane S.↗
NASA NTRS1990

EZDESIT: A Computer Program for Structural Element Sizing and Vehicle Weight Prediction

A method is presented for formulating stiffness terms and thermal coefficients of fiber reinforced composite, stiffened panels for input to finite element analysis (FEA). The method is robust enough to handle panels with general cross sectional shapes, including those which are unsymmetric and/or unbalanced. New thermal coefficients are introduced to quantify panel response from through-the-thickness temperature gradients. Equations are defined for stiffness, thermal expansion, and thermal bending that consider the full complement of membrane, bending, membrane-bending coupling, and transverse shear behavior. A technique of implementing this capability with a single plane of shell finite elements using the MSC/NASTRAN™ FEA program is revealed. Finally, an example of a composite, hat-stiffened panel is included to demonstrate errors that occur when an unsymmetric panel is symmetrically formulated as traditionally done. These erroneous values and the correct ones produced from the presented method are listed for the panel's stiffness matrices, thermal expansion and bending vectors, and the forces and moments that are thermally induced from in-plane and through-the-thickness temperature gradients.

Jeffrey A Cerro↗
NASA NTRS1998

Global Nonlinear Parametric Modeling with Application to F-16 Aerodynamics

A global nonlinear parametric modeling technique is described and demonstrated. The technique uses multivariate orthogonal modeling functions generated from the data to determine nonlinear model structure, then expands each retained modeling function into an ordinary multivariate polynomial. The final model form is a finite multivariate power series expansion for the dependent variable in terms of the independent variables. Partial derivatives of the identified models can be used to assemble globally valid linear parameter varying models. The technique is demonstrated by identifying global nonlinear parametric models for nondimensional aerodynamic force and moment coefficients from a subsonic wind tunnel database for the F-16 fighter aircraft. Results show less than 10% difference between wind tunnel aerodynamic data and the nonlinear parameterized model for a simulated doublet maneuver at moderate angle of attack. Analysis indicated that the global nonlinear parametric models adequately captured the multivariate nonlinear aerodynamic functional dependence.

Morelli, Eugene A.↗
NASA NTRS1997

Global Nonlinear Parametric Modeling with Application to F-16 Aerodynamics

A global nonlinear parametric modeling technique is described and demonstrated. The technique uses multivariate orthogonal modeling functions generated from the data to determine nonlinear model structure, then expands each retained modeling function into an ordinary multivariate polynomial. The final model form is a finite multivariate power series expansion for the dependent variable in terms of the independent variables. Partial derivatives of the identified models can be used to assemble globally valid linear parameter varying models. The technique is demonstrated by identifying global nonlinear parametric models for nondimensional aerodynamic force and moment coefficients from a subsonic wind tunnel database for the F-16 fighter aircraft. Results show less than 10% difference between wind tunnel aerodynamic data and the nonlinear parameterized model for a simulated doublet maneuver at moderate angle of attack. Analysis indicated that the global nonlinear parametric models adequately captured the multivariate nonlinear aerodynamic functional dependence.

Morelli, Eugene A.↗
NASA NTRS1983

Technique for removing resin from a molded object

Resin is removed from a molded object in such a way that no cracks or expansion occurs in the casting. The resin is first mixed with a ceramics powder or metal powder. This mixture is then molded and the resin is removed by heat. The molded object is then placed into a container which is sealed and large enough to allow the gas from the resin to be controlled by heat from the resin. The gas pressure at the surface of the object is increased by the gas pressure generated from the resin and the resin removed. The increase in gas pressure from the surface of the molded object is 1.5 atm to 3 atm at 350 C to 400 C.

Hemmi, I.↗
NASA NTRS1992

Composite Stiffened Panels: Part I - Stiffness, Thermal Expansion, and Thermal Bending Formulation for Finite Element Analysis

A method is presented for formulating stiffness terms and thermal coefficients of fiber-reinforced composite, stiffened panels for input to finite element analysis (FEA). The method is robust enough to handle panels with general cross sectional shapes, including those which are unsymmetric and/or unbalanced. New thermal coefficients are introduced to quantify panel response from through-the-thickness temperature gradients. Equations are defined for stiffness, thermal expansion, and thermal bending that consider the full complement of membrane, bending, membrane-bending coupling, and transverse shear behavior. A technique of implementing this capability with a single plane of shell finite elements using the MSC/NASTRAN(TradeMark) FEA program is revealed. Finally, an example of a composite, hat-stiffened panel is included to demonstrate errors that occur when an unsymmetric panel is symmetrically formulated as traditionally done. These erroneous values and the correct ones produced from the presented method are listed for the panel's stiffness matrices, thermal expansion and bending vectors, and the forces and moments that are thermally induced from in-plane and through-the-thickness temperature gradients.

Craig S Collier↗
NASA NTRS1994

Response of a grounded dielectric slab to an impulse line source using leaky modes

This paper describes how expansions in leaky (or improper) modes may be used to represent the continuous spectrum in an open radiating waveguide. The technique requires a thorough knowledge of the life history of the improper modes as they migrate from improper to proper Riemann surfaces. The method is illustrated by finding the electric field resulting from an impulsively forced current located in the free space above a grounded dielectric slab.

DIELECTRIC SLABS↗
NASA NTRS1992

Hybrid analytical technique for the nonlinear analysis of curved beams

The application of a two-step hybrid technique to the geometrically nonlinear analysis of curved beams is used to demonstrate the potential of hybrid analytical techniques in nonlinear structural mechanics. The hybrid technique is based on successive use of the perturbation method and a classical direct variational procedure. The functions associated with the various-order terms in the perturbation expansion of the fundamental unknowns, and their sensitivity derivatives with respect to material and geometric parameters of the beam, are first obtained by using the perturbation method. These functions are selected as coordinate functions (or modes) and the classical direct variational technique is then used to compute their amplitudes. The potential of the proposed hybrid technique for nonlinear analysis of structures is discussed. The effectiveness of the hybrid technique is demonstrated by means of numerical examples. The symbolic computation system Mathematica is used in the present study. The tasks performed on Mathematica include: (1) generation of algebraic expressions for the perturbation functions of the different response quantities and their sensitivity derivatives: and (2) determination of the radius of convergence of the perturbation series.

Noor, A. K.↗
NASA NTRS1976

Measured opening characteristics of an electromagnetically opened diaphragm for the Langley expansion tunnel

Results from an experimental study of the opening characteristics of an electromagnetically opened, 15.24 cm diameter diaphragm are presented. This diaphragm consists of a polyester film bonded to a preformed wire and is opened by passing a current pulse (capacitor discharge) through the wire. The diaphragm separates the acceleration section of the expansion tunnel from the nozzle so that the nozzle may be at a lower pressure than the acceleration section prior to a test. Opening times and cleanness of the opened area were examined for dependence on diaphragm thickness, on wire diameter, on technique of bonding the wire to the diaphragm, and on voltage and energy level of the energy source. Time histories of the pitot pressure measured at the expansion-tunnel nozzle entrance location are presented for (1) no diaphragm, (2) a flow-opened diaphragm, and (3) an electromagnetically opened diaphragm.

Moore, J. A.↗
NASA NTRS1987

Wall relaxation and the driving forces for cell expansive growth

When water uptake by growing cells is prevented, the turgor pressure and the tensile stress in the cell wall are reduced by continued wall loosening. This process, termed in vivo stress relaxation, provides a new way to study the dynamics of wall loosening and to measure the wall yield threshold and the physiological wall extensibility. Stress relaxation experiments indicate that wall stress supplies the mechanical driving force for wall yielding. Cell expansion also requires water absorption. The driving force for water uptake during growth is created by wall relaxation, which lowers the water potential of the expanding cells. New techniques for measuring this driving force show that it is smaller than believed previously; in elongating stems it is only 0.3 to 0.5 bar. This means that the hydraulic resistance of the water transport pathway is small and that rate of cell expansion is controlled primarily by wall loosening and yielding.

NASA Program Space Biology↗
NASA NTRS1972

Numerical check on the accuracy of spherical-wave expansions.

A simple and sensitive test for evaluating the numerical accuracy of a spherical-wave expansion is presented. The basic idea is to compare two different expansions of the same electromagnetic field, computed with respect to different coordinate origins. The use of the technique is illustrated by an example based on the experimental pattern of a horn antenna.

Ludwig, A. C.↗
NASA NTRS1982

An estimation of the condensation rates in three severe storm systems from satellite observations of the convective mass flux

A technique was developed for estimating the condensation rates of convective storms using satellite measurements of cirrus anvil expansion rates and radiosonde measurements of environmental water vapor. Three cases of severe convection in Oklahoma were studied and a diagnostic model was developed for integrating radiosonde data with satellite data. Two methods were used to measure the anvil expansion rates - the expansion of isotherm contours on infrared images, and the divergent motions of small brightness anomalies tracked on the visible images. The differences between the two methods were large as the storms developed, but these differences became small in the latter stage of all three storms. A comparison between the three storms indicated that the available moisture in the lowest levels greatly affected the rain rates of the storms. This was evident from both the measured rain rates of the storms and the condensation rates estimated by the model. The possibility of using this diagnostic model for estimating the intensities of convective storms also is discussed.

Mack, R. A.↗
NASA NTRS1986

Thermal stability of lightweight graphite glass sandwich reflectors for far infrared astronomy

Graphite fiber-reinforced glass matrix composites are being developed for a variety of structural applications requiring excellent thermomechanical stability. These materials are ideally suited for lightweight, high strength, thermally stable infrared mirrors because of their low density, low thermal expansion, high strength and stiffness, and their ability to be machined, replicated and figured using standard polishing techniques. These properties are particularly promising for applications such as a 3-meter balloon-borne far-infrared and submillimeter telescope mirror which must be both very lightweight and able to retain its figure accuracy when cycled between room temperature and its operating temperature of -50 C. This paper presents the results of a set of low temperature optical tests conducted to determine the figure stability of a 30-cm diameter, frit-bonded graphite/glass mirror in the +20 to -60 C temperature range using a 10.6 micron laser interferometer. The results indicate that the residual change in figure was less than 0.3 microns, rms.

Bluege, J. H.↗
NASA NTRS1993

Thermal stress effects in intermetallic matrix composites

Intermetallic matrix composites develop residual stresses from the large thermal expansion mismatch (delta-alpha) between the fibers and matrix. This work was undertaken to: establish improved techniques to measure these thermal stresses in IMC's; determine residual stresses in a variety of IMC systems by experiments and modeling; and, determine the effect of residual stresses on selected mechanical properties of an IMC. X ray diffraction (XRD), neutron diffraction (ND), synchrotron XRD (SXRD), and ultrasonics (US) techniques for measuring thermal stresses in IMC were examined and ND was selected as the most promising technique. ND was demonstrated on a variety of IMC systems encompassing Ti- and Ni-base matrices, SiC, W, and Al2O3 fibers, and different fiber fractions (Vf). Experimental results on these systems agreed with predictions of a concentric cylinder model. In SiC/Ti-base systems, little yielding was found and stresses were controlled primarily by delta-alpha and Vf. In Ni-base matrix systems, yield strength of the matrix and Vf controlled stress levels. The longitudinal residual stresses in SCS-6/Ti-24Al-llNb composite were modified by thermomechanical processing. Increasing residual stress decreased ultimate tensile strength in agreement with model predictions. Fiber pushout strength showed an unexpected inverse correlation with residual stress. In-plane shear yield strength showed no dependence on residual stress. Higher levels of residual tension led to higher fatigue crack growth rates, as suggested by matrix mean stress effects.

Wright, P. K.↗
NASA NTRS2012

Remote and In Situ Observations of an Unusual Earth-Directed Coronal Mass Ejection from Multiple Viewpoints

During June 16-21, 2010, an Earth-directed Coronal Mass Ejection (CME) event was observed by instruments onboard STEREO, SOHO, MESSENGER and Wind. This event was the first direct detection of a rotating CME in the middle and outer corona. Here, we carry out a comprehensive analysis of the evolution of the CME in the interplanetary medium comparing in-situ and remote observations, with analytical models and three-dimensional reconstructions. In particular, we investigate the parallel and perpendicular cross section expansion of the CME from the corona through the heliosphere up to 1 AU. We use height-time measurements and the Gradual Cylindrical Shell (GCS) technique to model the imaging observations, remove the projection effects, and derive the 3-dimensional extent of the event. Then, we compare the results with in-situ analytical Magnetic Cloud (MC) models, and with geometrical predictions from past works. We nd that the parallel (along the propagation plane) cross section expansion agrees well with the in-situ model and with the Bothmer & Schwenn [1998] empirical relationship based on in-situ observations between 0.3 and 1 AU. Our results effectively extend this empirical relationship to about 5 solar radii. The expansion of the perpendicular diameter agrees very well with the in-situ results at MESSENGER ( 0:5 AU) but not at 1 AU. We also find a slightly different, from Bothmer & Schwenn [1998], empirical relationship for the perpendicular expansion. More importantly, we find no evidence that the CME undergoes a significant latitudinal over-expansion as it is commonly assumed

Nieves-Chinchilla, T.↗