SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Threshold extension device connected between demodulator output and filter output minimizes clicking noise. Device consists of click-eliminating signal transfer channel with follow-and-hold circuit and detector for sensing click impulses. Final output consists of signal plus low level noise without high amplitude impulses.
An analytical and experimental program to demonstrate the technical feasibility of a lightweight, high-efficiency, 1-2 kW cw, permanent magnet focused klystron operating at 12.0 GHz was described. The design is based on use of a samarium-cobalt permanent magnet for focusing of the electron beam and choice of the most optimum parameters for maximum efficiency. A filter-loaded output circuit is used for the required bandwidth. The design incorporates a collector which is demountable from the tube to facilitate multistage depressed collector experiments, permitting replacement with a NASA-designed axisymmetric, electrostatic collector for linear beam microwave tubes. A further requirement is that the focusing field between the last interaction gap and the collector decay in a prescribed manner referred to as adiabatic expansion.
A trainable acoustic pattern recognizer manufactured by Scope Electronics is presented. The voice command system VCS encodes speech by sampling 16 bandpass filters with center frequencies in the range from 200 to 5000 Hz. Variations in speaking rate are compensated for by a compression algorithm that subdivides each utterance into eight subintervals in such a way that the amount of spectral change within each subinterval is the same. The recorded filter values within each subinterval are then reduced to a 15-bit representation, giving a 120-bit encoding for each utterance. The VCS incorporates a simple recognition algorithm that utilizes five training samples of each word in a vocabulary of up to 24 words. The recognition rate of approximately 85 percent correct for untrained speakers and 94 percent correct for trained speakers was not considered adequate for flight systems use. Therefore, the built-in recognition algorithm was disabled, and the VCS was modified to transmit 120-bit encodings to an external computer for recognition.
By directly heating lithium hydride in a vacuum, up to 18 micro-A/sq cm of negative hydrogen has been obtained from the crystal lattice. The amount of ion current extracted and analyzed is closely related to the temperature of the sample and to the rate at which the temperature is changed. The ion current appears to be emission limited and saturates with extraction voltage. For a fixed extraction voltage, the ion current could be maximized by placing a grid between the sample surface and the extraction electrode. Electrons accompanying the negative ions were removed by a magnetic trap. A Wein velocity filter was designed and built to provide definitive mass analysis of the extracted ion species. This technique when applied to other alkali hydrides may produce even higher intensity beams possessing low values of emittance.
Topics covered include: Stable, Thermally Conductive Fillers for Bolted Joints; Connecting to Thermocouples with Fewer Lead Wires; Zipper Connectors for Flexible Electronic Circuits; Safety Interlock for Angularly Misdirected Power Tool; Modular, Parallel Pulse-Shaping Filter Architectures; High-Fidelity Piezoelectric Audio Device; Photovoltaic Power Station with Ultracapacitors for Storage; Time Analyzer for Time Synchronization and Monitor of the Deep Space Network; Program for Computing Albedo; Integrated Software for Analyzing Designs of Launch Vehicles; Abstract-Reasoning Software for Coordinating Multiple Agents; Software Searches for Better Spacecraft-Navigation Models; Software for Partly Automated Recognition of Targets; Antistatic Polycarbonate/Copper Oxide Composite; Better VPS Fabrication of Crucibles and Furnace Cartridges; Burn-Resistant, Strong Metal-Matrix Composites; Self-Deployable Spring-Strip Booms; Explosion Welding for Hermetic Containerization; Improved Process for Fabricating Carbon Nanotube Probes; Automated Serial Sectioning for 3D Reconstruction; and Parallel Subconvolution Filtering Architectures.
In scanning tunneling microscopy (STM), the surface conductivity, σ, contributes to the total tunneling current due to a quantum phenomenon. Here, the surface conductivity may change from atom to atom during a scan. It is an important electronic property of the surface that cannot be directly measured with current spectroscopy methods. In this paper, we propose an offline estimation method based on augmented state Kalman filter to determine σ. We demonstrate the successful application of this method to a set of STM images obtained from a Si(100) – 2 × 1:H passivated surface.
The detection and size analysis of small metal particles supported on amorphous substrates becomes increasingly difficult when the particle size approaches that of the phase contrast background structures of the support. An approach of digital image analysis, involving Fourier transformation of the original image, filtering, and image reconstruction was studied with respect to the likelihood of unambiguously detecting particles of less than 1 nm diameter on amorphous substrates from a single electron micrograph.
A method of polarimetric imaging, now undergoing development, involves the use of two photoelastic modulators in series, driven at equal amplitude but at different frequencies. The net effect on a beam of light is to cause (1) the direction of its polarization to rotate at the average of two excitation frequencies and (2) the amplitude of its polarization to be modulated at the beat frequency (the difference between the two excitation frequencies). The resulting modulated optical light beam is made to pass through a polarizing filter and is detected at the beat frequency, which can be chosen to equal the frame rate of an electronic camera or the rate of sampling the outputs of photodetectors in an array. The method was conceived to satisfy a need to perform highly accurate polarimetric imaging, without cross-talk between polarization channels, at frame rates of the order of tens of hertz. The use of electro-optical modulators is necessitated by a need to obtain accuracy greater than that attainable by use of static polarizing filters over separate fixed detectors. For imaging, photoelastic modulators are preferable to such other electrio-optical modulators as Kerr cells and Pockels cells in that photoelastic modulators operate at lower voltages, have greater angular acceptances, and are easier to use. Prior to the conception of the present method, polarimetric imaging at frame rates of tens of hertz using photoelastic modulators was not possible because the resonance frequencies of photoelastic modulators usually lie in the range from about 20 to about 100 kHz.
On-line access to complete texts of scholarly journal articles, conference papers, and books is facilitated by rapidly developing World-wide Web Internet access and capabilities. Meanwhile, print publications continue to be produced and read in spite of the proliferation of many networked electronic publications. The purpose of this presentation is to highlight fundamental issues impacting stakeholder groups, as the trend continues towards migration from paper to affordable ubiquitous networked full-text publications. Librarians, publishers, authors and end-users have various viewpoints, interests, and concerns. There are many issues challenging all stakeholder groups. For instance, all share concerns about administering copyright compliance and enforcing fair use. Uncontrollable electronic downstreaming could result in infringed copyright, while limiting a publisher's entitled revenue stream. Moreover, metered fee-based access may hamper scholarly information research. And, self-authoring on the Internet without peer filtering could lead to information clutter. Many related issues challenge librarians in particular. Among these are rising journal subscription prices, regardless if offered in print or electronic. Some electronic offerings are independent of print, others supplement or duplicate print; several publishers presently require subscribing to print in order to access electronic. Furthermore, numbers of publications are n'ow being marketed via the Internet directly to end-users, which can be viewed as encouraging users to bypass the traditional library. A key issue challenging publishers today is the rapidly expanding electronic user base that is demanding delivery of added-value full-text to desktop computers. Also of growing concern appears to be the decline in print sales to libraries, thereby reducing traditional revenue stream potential. Nowadays, publishers are more hesitant about investing in the production of publications geared toward small niche subjects, since these tend to require higher pricing and carry limited sales potential. Both electronic and print publications necessitate similar editorial, production, operating, and marketing dollars. Tradeoffs owing to delivery format difference do not necessarily mean less dollars need to be spent. Authors wishing to publish books are facing a decline in the role of scholarly monographs in electronic media. However, they are witnessing increased roles of electronic preprints and electronic journal articles. Moreover, the Internet fosters self-publishing without peer monitoring or formal review. Issues challenging end-users include electronic barriers to peer-reviewed formal published works (i.e., fee-based subscriptions to journal literature vs. traditional free-library concept). This often means password only access or IP address controlled site-licensed access. Also, in an uncontrolled Internet environment, sometimes there is a blurring of publication authorship/ownership, as various pieces of publications are cut/pasted into/re-posted on various, disconnected Web searchable home pages.
In order to meet ever-increasing data return requirements, more satellites are using the near-Earth Ka-band (25.5 – 27.0 GHz) to achieve higher downlink rates. The paper discusses the Universal Space Transponder - Ka-band Modulator (UST-KaM) developed at the NASA Jet Propulsion Laboratory for the NASA-ISRO SAR (NISAR) mission, which is capable of transmitting up to 1.74 Gbps with 7/8 LDPC encoding. The UST-KaM utilizes OQPSK with both baseband and RF filtering to contain the 1 Gsps transmission spectrum within the 1.5 GHz Ka-band, even with the use of an external, saturated amplifier. Due to the high data rates involved, several technical hurdles were overcome in both the digital and RF designs. The UST-KaM is a software defined radio with two digital circuit board assemblies: a low speed housekeeper board for commanding and telemetry, and a high-rate signal processing board known as the Signal Processing Module (SPM). The SPM receives data from the spacecraft via a SERDES interface at up to 2 Gbps, processes and encodes the data using a Xilinx Virtex-5 FPGA, and produces 1 Gsps OQPSK I and Q waveforms via synchronized, multiplexed DACs. The RF Electronics in the UST-KaM employ a heterodyne architecture in which the I/Q digital waveforms are filtered and then up-converted using a sub-harmonic IQ mixer. The LO of the converter, which is included in the exciter assembly, is at 13.125GHz, and the RF output is a 26.25GHz carrier which is modulated with the OQPSK waveforms. The output of the mixer is then filtered using low loss quartz thinfilm edge coupled Chebyshev filters and amplified through a series of low gain Ka-Band amplifiers. The exciter assembly also has a 2GHz, low-phase-noise, PLL synthesizer to supply the clock to the DACs for the high rate digital waveforms.
We present results from x-ray imaging of high-aspect-ratio magnetic reconnection experiments driven at the National Ignition Facility. Two parallel, self-magnetized, elongated laser-driven plumes are produced by tiling 40 laser beams. A magnetic reconnection layer is formed by the collision of the plumes. A gated x-ray framing pinhole camera with micro-channel plate detector produces multiple images through various filters of the formation and evolution of both the plumes and current sheet. As the diagnostic integrates plasma self-emission along the line of sight, two-dimensional electron temperature maps ⟨Te⟩Y are constructed by taking the ratio of intensity of these images obtained with different filters. The plumes have a characteristic temperature ⟨Te⟩Y=240 ± 20 eV at 2 ns after the initial laser irradiation and exhibit a slow cooling up to 4 ns. The reconnection layer forms at 3 ns with a temperature ⟨Te⟩Y=280 ± 50 eV as the result of the collision of the plumes. The error bars of the plumes and current sheet temperatures separate at 4 ns, showing the heating of the current sheet from colder inflows. Using a semi-analytical model, we survey various heating mechanisms in the current sheet. We find that reconnection energy conversion would dominate at low density (ne≲7×1018 cm−3) and electron-ion collisional drag at high-density (≳1019 cm−3).
A new high radial resolution 2D multichannel Charge eXchange Imaging (CXI) diagnostic is under development for deployment at DIII-D. Here, the diagnostic system will measure low-to-intermediate radial wavenumber carbon density fluctuations by observing the n = 8 – 7 (λ = 529.06 nm) C-VI emission line, resulting from charge exchange collisions between heating neutral beam atoms and the intrinsic carbon ion density. The new CXI diagnostic will provide measurements with ΔR ~ 0.4 cm to access higher k r instabilities (k r < 8 cm –1 ) predicted to arise in the steep-gradient region of the H-mode pedestal. The CXI system will feature 60 fiber bundles in a 12 × 5 arrangement, with each bundle consisting of four 1 mm fibers. A custom optical system has been designed to filter and image incoming signals onto an 8 × 8 avalanche photodiode array. Additionally, a novel electronics suite has been designed and commissioned to amplify and digitize the relatively low-intensity carbon signal at a 2 MHz bandwidth. Forward modeling results of the active C-VI emission suggest sufficient signal to noise ratios to resolve turbulent fluctuations. Prototype measurements demonstrate the ability to perform high frequency pedestal measurements.
Two camera systems are installed on the DIII-D tokamak at the toroidal positions of 90° (90° system) and 225° (225° system), respectively. The cameras have two types of relay optics, namely, a coherent optical fiber bundle and a periscope system. The periscope system provides absolute intensity calibration stability while sacrificing resolution (10 lp/mm), while the fiber system provides high resolution (16 lp/mm) while sacrificing calibration stability. The periscope is available only for the 90° system. The optics of the 225° system were designed for view stability, repeatability, and easy maintenance. The cameras are located inside optimized neutron, x ray and magnetic shielding in order to reduce electronics damage, reboots, and magnetic and neutron interference, increasing the overall system reliability. An automated filter wheel, providing remote filter change, allows for remote wavelength selection. A software suite automates camera acquisition and data storage, allowing for remote operation and reduced operator involvement. System metadata is used to streamline the data analysis workflow, particularly for intensity calibration. Here, the spatial calibration uses multiple observable wall features, resulting in a reconstruction accuracy ≤2 cm.
The design, development and testing of the infrared interferometer spectrometer is reported with emphasis on the unique features of the Mariner instrument as compared to previous IRIS instruments flown on the Nimbus meteorological research satellites. The interferometer functions in the spectral range from 50 microns to 6.3 microns. A noise equivalent radiance of 0.5 X 10 to the -7th power W/sq cm/ster/cm has been achieved. Major improvements that were implemented included the cesium iodide beamsplitter and electronic features to suppress the effect of vibration on the Michelson mirror motion and digital filtering through the summation of increased sampling of the infrared signal. A bit error detection and correction scheme was also implemented in order to recover the science data with a higher level of confidence over the telecommunication link.
Helium ions were produced in an electron bombardment ion source and directed into a gas cell containing carbon dioxide. A Wien filter placed between the ion source and the gas cell insured that only singly charged helium ions reached the cell. The spectrum obtained for the bombardment of carbon dioxide with the helium ions at 1200 eV is shown in a graph. Prominent features of the lower spectrum are two atomic lines at 3889 and 4471 A.
Experiments on an automatic multisensor navigation concept are being conducted in a Cessna 402B. The test system consists of VOR, DME, and air data sensors controlled by a Hewlett Packard 9820A electronic calculator which processes the data and, by means of a four-state Kalman filter, outputs position and ground and wind velocities to a map display. Novel features which make such a system potentially low-cost include frequency-scanning operation of a single VOR receiver and a single DME transceiver and use of a shed-vortex true airspeed sensor. Results obtained during flight in a local area where six to eight DME NAVAIDS were receivable yielded better than 1/4-mile accuracy.
A hybrid-computer simulation of the over the wing turbofan engine was constructed to develop the dynamic design of the control. This engine and control system includes a full authority digital electronic control using compressor stator reset to achieve fast thrust response and a modified Kalman filter to correct for sensor failures. Fast thrust response for powered-lift operations and accurate, fast responding, steady state control of the engine is provided. Simulation results for throttle bursts from 62 to 100 percent takeoff thrust predict that the engine will accelerate from 62 to 95 percent takeoff thrust in one second.
It is argued that the next generation of imaging spectrometers will need greater capabilities and more flexibility than the High Resolution Imaging Spectrometer (HIRIS) and the Moderate Resolution Imaging Spectrometer (MODIS), which were designed for the first Earth Observation System platform. The emerging technology that represents a major advance in the scientific utility of imaging spectrometry is the acoustooptic tunable filters, (AOTFs). AOTFs are compact robust solid-state crystals which provide rapid (millisecond) electronically-controlled spectral tunability. This paper discusses the evolving requirements of imaging spectrometers and examines the basic system parameters of the HIRIS and the MODIS concepts involving the use of AOTFs, which will satisfy these requirements.