Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrolyte additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Fluorinated Glyme Solvents to Extend Lithium-Sulfur Battery Life (Final Technical Report, Unlimited)

This project investigated a number of partially fluorinated glymes (PFGs) as electrolyte cosolvents to improve the performance of lithium-sulfur (Li-S) batteries. A major issue in Li-S cells is the electrochemical reaction of sulfur in the cathode to form lithium polysulfides (LPS) that dissolve in the electrolyte. Those LPS are electrochemically and chemically reactive at the lithium anode, resulting in lithium sulfide deposition on the anode and also electrochemical reaction at both the anode and cathode, leading to a “polysulfide shuttle” and reduced coulombic efficiency (CE) and self-discharge of the cell. PFGs reduce the solubility of LPS while maintaining good solubility of lithium salts such as LiTFSI. By adjusting the amount of PFG as cosolvent in the electrolyte, we showed that the solubility of LPS in the electrolyte can be tuned. (It is not desirable to completely eliminate LPS in the electrolyte, as they facilitate electrochemical reaction of the electrically insulating S 8 and Li 2 S within the cathode by shuttling charge between them and the conductive carbon.) Another issue in Li-S cells is degradation of the Li anode over many cycles of stripping (discharge) and plating (charge). We showed that PFGs have a beneficial effect on the physical morphology of the Li anode, SEI formation, and the CE of a Li-Li cell. Among the many PFGs tested, we found the best performance from PFGs designated PFG2 and PFG5, and these two PFGs were thoroughly studied. A systematic coin-cell study of electrolyte solvents of 90:10, 80:20, or 70:30 DME:PFG (DME = 1,2-dimethoxyethane) revealed some systematic trends: a higher percentage of PFG solvent led to substantially longer cycle life, but at the same time reduced specific capacity (mAh/g(S)) and cell capacity at higher rates. These studies used LiFSI as the electrolyte salt, as it was found to extend cycle life compared to LiTFSI. Finally, the addition of a small amount of 1,3-dioxolane (DOL) to the electrolyte was found to be beneficial. The overall optimal electrolyte solution was found to be 0.6 M LiFSI + 0.5 M LiNO 3 in 75:5:20 DME/DOL/PFG (either PFG2 or PFG5).

25 ENERGY STORAGE↗
DOE OSTI2022

Localized Hydrophobicity in Aqueous Zinc Electrolytes Improves Zinc Metal Reversibility

The rechargeability of aqueous zinc metal batteries is plagued by parasitic reactions of the zinc metal anode and detrimental morphologies such as dendritic or dead zinc. To improve the zinc metal reversibility, hereby we report a new solution structure of aqueous electrolyte with hydroxyl-ions scavengers and hydrophobicity localized in solvent clusters. In this work we show that although hydrophobicity sounds counterintuitive for an aqueous system, hydrophilic pockets may be encapsulated inside a hydrophobic outer layer and a hydrophobic anode-electrolyte interface can be generated through the addition of a cation-philic, strongly anion-phobic, and OH - -reactive diluent. The localized hydrophobicity enables less active water and less absorbed water on the Zn anode surface, which suppresses the parasitic water reductions; while the hydroxyl-ion-scavenging functionality further minimizes undesired passivation layer formation, thus leading to superior reversibility (an average Zn plating/stripping efficiency of 99.72% for 1000 cycles) and lifetime (80.6% capacity retention after 5000 cycles) of zinc batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Enabling Magnesium Anodes by Tuning the Electrode/Electrolyte Interfacial Structure

Here, a new deposition mechanism is presented in this study to achieve highly reversible plating and stripping of magnesium (Mg) anodes for Mg-ion batteries. It is known that the reduction of electrolyte anions such as bi s (trifluoromethanesulfonyl) imide (TFSI - ) causes Mg surface passivation, resulting in poor electrochemical performance for Mg-ion batteries. We reveal that the addition of sodium cations (Na + ) in Mg-ion electrolytes can fundamentally alter the interfacial chemistry and structure at the Mg anode surface. The molecular dynamics simulation suggests that Na + cations contribute to a significant population in the interfacial double layer so that TFSI - anions are excluded from the immediate interface adjacent to the Mg anode. As a result, the TFSI - decomposition is largely suppressed so does the formation of passivation layers at the Mg surface. This mechanism is supported by our electrochemical, microscopic, and spectroscopic analyses. The resultant Mg deposition demonstrates smooth surface morphology and lowered overpotential compared to the pure Mg(TFSI) 2 electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2021

Formation of Stable Interphase of Polymer-in-Salt Electrolyte in All-Solid-State Lithium Batteries

The integration of solid-polymer electrolytes into all-solid-state lithium batteries is highly desirable to overcome the limitations of current battery configurations that have a low energy density and severe safety concerns. Polyacrylonitrile is an appealing matrix for solid-polymer electrolytes; however, the practical utilization of such polymer electrolytes in all-solid-state cells is impeded by inferior ionic conductivity and instability against a lithium-metal anode. In this work, we show that a polymer-in-salt electrolyte based on polyacrylonitrile with a lithium salt as the major component exhibits a wide electrochemically stable window, a high ionic conductivity, and an increased lithium-ion transference number. The growth of dendrites from the lithium-metal anode was suppressed effectively by the polymer-in-salt electrolyte to increase the safety features of the batteries. In addition, we found that a stable interphase was formed between the lithium-metal anode and the polymer-in-salt electrolyte to restrain the uncontrolled parasitic reactions, and we demonstrated an all-solid-state battery configuration with a LiFePO 4 cathode and the polymer-in-salt electrolyte, which exhibited a superior cycling stability and rate capability.

Gao, Hongcai↗
DOE OSTI2023

Understanding the Surprising Ionic Conductivity Maximum in Zn(TFSI) 2 Water/Acetonitrile Mixture Electrolytes

Aqueous electrolytes composed of 0.1 M zinc bis-(trifluoromethyl-sulfonyl)-imide (Zn-(TFSI) 2 ) and acetonitrile (ACN) were studied using combined experimental and simulation techniques. The electrolyte was found to be electrochemically stable when the ACN V% is higher than 74.4. In addition, it was found that the ionic conductivity of the mixed solvent electrolytes changes as a function of ACN composition, and a maximum was observed at 91.7 V% of ACN although the salt concentration is the same. This behavior was qualitatively reproduced by molecular dynamics (MD) simulations. Detailed analyses based on experiments and MD simulations show that at high ACN composition the water network existing in the high water composition solutions breaks. As a result, the screening effect of the solvent weakens and the correlation among ions increases, which causes a decrease in ionic conductivity at high ACN V%. Furthermore, this study provides a fundamental understanding of this complex mixed solvent electrolyte system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Molecular Engineering Enabled Stable Deep Eutectic Amide-Based Electrolyte for High-Temperature Lithium–Metal Batteries

The development of advanced lithium-metal batteries (LMBs), such as high-temperature LMBs and high-energy-density LMBs, has critical requirements for electrolytes. However, conventional electrolytes suffer from thermal instability and insufficient electrolyte/Li interfacial compatibility, severely limiting their utilization in high-temperature LMBs. Herein, we design a high-temperature N-methylacetamide (NMAc)-based deep eutectic electrolyte (DEE) by molecular engineering on a solvation structure via a sacrificial additive of vinyl ethylene carbonate (VEC). Specifically, VEC interacts with the Li prior to NMAc, facilitating the formation of a solid electrolyte interphase to inhibit the reaction between Li and NMAc. The stable VEC-DEE effectively suppresses the growth of lithium dendrites and ensures the battery a cycling stability of 550 cycles at 80 °C. Additionally, we also demonstrate the application of VEC-DEE in high-energy-density LMBs with a high mass loading of 2.5 mAh/cm 2 . In conclusion, this research opens a new avenue for the rational design of advanced high-temperature electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2021

Stabilizing the Solid‐Electrolyte Interphase with Polyacrylamide for High‐Voltage Aqueous Lithium‐Ion Batteries

Abstract The introduction of “water‐in‐salt” electrolyte (WiSE) concept opens a new horizon to aqueous electrochemistry that is benefited from the formation of a solid‐electrolyte interphase (SEI). However, such SEI still faces multiple challenges, including dissolution, mechanical damaging, and incessant reforming, which result in poor cycling stability. Here, we report a polymeric additive, polyacrylamide (PAM) that effectively stabilizes the interphase in WiSE. With the addition of 5 molar % PAM to 21 mol kg −1 LiTFSI electrolyte, a LiMn 2 O 4 ∥L‐TiO 2 full cell exhibits enhanced cycling stability with 86 % capacity retention after 100 cycles at 1 C. The formation mechanism and evolution of PAM‐assisted SEI was investigated using operando small angle neutron scattering and density functional theory (DFT) calculations, which reveal that PAM minimizes the presence of free water molecules at the anode/electrolyte interface, accelerates the TFSI − anion decomposition, and densifies the SEI.

25 ENERGY STORAGE↗
DOE OSTI2024

Recent Progress on Dominant Sulfide‐Type Solid‐State Na Superionic Conductors for Solid‐State Sodium Batteries

Abstract Over the past decade, solid‐state batteries have garnered significant attentions due to their potentials to deliver high energy density and excellent safety. Considering the abundant sodium (Na) resources in contrast to lithium (Li), the development of sodium‐based batteries has become increasingly appealing. Sulfide‐based superionic conductors are widely considered as promising solid eletcrolytes (SEs) in solid‐state Na batteries due to the features of high ionic conductivity and cold‐press densification. In recent years, tremendous efforts have been made to investigate sulfide‐based Na‐ion conductors on their synthesis, compositions, conductivity, and the feasibility in batteries. However, there are still several challenges to overcome for their practical applications in high performance solid‐state Na batteries. This article provides a comprehensive update on the synthesis, structure, and properties of three dominant sulfide‐based Na‐ion conductors (Na 3 PS 4 , Na 3 SbS 4 , and Na 11 Sn 2 PS 12 ), and their families that have a variety of anion and cation doping. Additionally, the interface stability of these sulfide electrolytes toward the anode is reviewed, as well as the electrochemical performance of solid‐state Na batteries based on different types of cathode materials (metal sulfides, oxides, and organics). Finally, the perspective and outlook for the development and practical utilization of sulfide‐based SE in solid‐state batteries are discussed.

Guo, Xiaolin↗
DOE OSTI2024

Enhancing the Reaction Kinetics and Stability of Co‐Free Li‐Rich Cathode Materials via a Multifunctional Strategy

Co-free Li-rich layered oxides (CFLLOs) with anionic redox activity are among the most promising cathode materials for high-energy-density and low-cost lithium-ion batteries (LIBs). However, irreversible oxygen release often causes severe structural deterioration, electrolyte decomposition, and the formation of unstable cathode-electrolyte interface (CEI) film with high impedance. Additionally, the elimination of cobalt elements further deteriorates the reaction kinetics, leading to reduced capacity and poor rate performance. Here, in this study, a multifunctional strategy is proposed, incorporating Li 2 MnO 3 phase content regulation, micro-nano structure design, and heteroatom substitution. The increased content of Li 2 MnO 3 phase enhances the capacity through oxygen redox. The smaller nanoscale primary particles induce greater tensile strain and introduce more grain boundaries, thereby improving the reaction kinetics and reactivity, while the larger micron-sized secondary particles help to reduce interfacial side reactions. Furthermore, Na⁺ doping modulates the local coordination environment of oxygen, stabilizing both the anion framework and the crystal structure. As a result, the designed cathode exhibits enhanced rate performance, delivering a capacity of 158 mAh g⁻¹ at 5.0 C and improved cyclic stability, with a high capacity retention of 99% after 400 cycles at 1.0 C. This multifunctional strategy holds great promise for advancing the practical application of CFLLOs in next-generation LIBs.

Co-free Li-rich layered oxide↗
DOE OSTI2024

Operando NMR characterization of cycled and calendar aged nanoparticulate silicon anodes for Li-ion batteries

Replacing graphite anodes with Si anodes can greatly increase the energy of current Li-ion batteries. Detailed characterization of Si lithiation reactions, SEI formation, and reversibility are therefore active areas of research. Solid-state 7 Li nuclear magnetic resonance (NMR) spectroscopy is useful for characterizing different lithium local environments within Si anodes. Here, we developed an operando NMR methodology to characterize aging of carbon-coated nanoparticulate Si anodes in pouch cells paired with Ni-rich cathodes. We observed a new lithiation mechanism in the Si nanoparticles: direct formation of over-lithiated Li 15+x Si 4 (x<0.6) phase. Furthermore, our novel operando cells maintained good performance with long-term cycle and calendar aging. Here we identified trapped lithium silicides as a major contributor to capacity fade with aging. Finally, we determined that the addition of Mg (TFSI) 2 to the electrolyte decreased the amount of trapped lithium silicides and therefore increased the capacity and capacity retention for the nanoparticulate Si used.

25 ENERGY STORAGE↗
DOE OSTI2025

Single Component Dye-Sensitized Solar Cells Enabled by Copper Chemistry: Introduction of the Retro Cell

The possibility of utilizing a single molecule to act as both a chromophore and a redox shuttle in a new configuration of a dye-sensitized solar cell (DSSC) is investigated. This design, termed a retro cell, exploits the copper chromophore, [Cu(dsbtmp) 2 ] + (dsbtmp = bis(2,9-di(sec-butyl)-3,4,7,8- tetramethyl-1,10-phenanthroline), which has been shown to have excited state lifetimes in excess of a microsecond, enabling sensitization of TiO 2 while dissolved in solution. The oxidized chromophore can then diffuse to the counter electrode to be regenerated. This concept simplifies the device components and fabrication and eliminates a charge transfer step compared to that of traditional DSSCs. Initial investigations show the concept is viable; however, the performance is suboptimal. We have found the addition of 4-tertbutylpyridine (TBP) to the electrolyte plays a crucial role in enabling solar energy conversion. Evidence of TBP displacing one of the dsbtmp ligands in the oxidized [Cu(dsbtmp) 2 ] 2+ complex has been presented, which likely plays an important role in reducing recombination and enabling charge collection. The performance-limiting steps and routes to improved performance and viability of a retro cell are further discussed.

14 SOLAR ENERGY↗
DOE OSTI2021

Effect of Added Salt on Disordered Poly(ethylene oxide)-Block-Poly(methyl methacrylate) Copolymer Electrolytes

In this report we studied the effect of salt addition on a diblock copolymer system with a negative Flory-Huggins interaction parameter, χ, indicative of attractive interactions between the two blocks. The system studied is poly(ethylene oxide)-block-poly(methyl methacrylate) (PEO-PMMA) with added lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt. We studied two asymmetric block copolymers, PEO-PMMA(10-33) and PEO-PMMA(10-64), where the numbers refer to the molar masses of the blocks in kg mol -1 . The small-angle X-ray scattering (SAXS) profiles for PEO-PMMA(10-33) were featureless at all salt concentrations. In contrast, PEO-PMMA(10-64) exhibited SAXS peaks when the salt concentration was between 0.22 ≤ m (mol Li/kg polymer) ≤ 0.44. The appearance of SAXS peaks only in PEO-PMMA(10-64) is consistent with the predictions of ionic self-consistent field theory developed by de la Cruz and co-workers, which predicts that in systems with negative χ, ordered phases are only found when the volume fraction of the ionic block is about 10%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Validated Reactive Force Field Quantifies MXene Interfacial Properties, Mechanics, and Thermal Transport

MXenes combine rich surface chemistry, mechanical strength, and high conductivity for a multitude of emerging applications. Predictive modeling supports accelerated materials designs and has been limited by the absence of validated and transferable force fields. Here, we introduce an interpretable, reactive INTERFACE force field (IFF and IFF-R) for Ti 3 C 2 T x MXenes that is trained based on chemical knowledge and achieves quantitative agreement with experiments across lattice parameters (<0.5%), density (<0.2%), liquid contact angles, Raman spectra, and the in-plane elastic modulus (∼320 GPa). The models cover surface terminations from hydroxyl (−OH) to fluorine (−F) groups and are extensible to other chemistries. We introduce pH-resolved surface chemistry and identify dopamine adsorption mechanisms at MXene–aqueous interfaces supported by QCM-D and UV–Vis experiments. The data reveal coplanar and perpendicular binding modes and concentration-dependent multilayer assembly. We predict previously inaccessible properties, including termination-dependent cleavage energies, interlayer shear moduli and dynamic shear failure, nanoindentation and brittle fracture, anisotropic in-plane and out-of-plane thermal conductivities, including the role of defects. Agreement with available experimental data is consistently close and exceeds DFT accuracy across the benchmark properties examined. The IFF/IFF-R model is compatible with CHARMM, AMBER, OPLS, and CVFF force fields for simulations of MXenes with diverse surface terminations, electrolyte interfaces, biointerfaces, and polymer composites without additional parameters. Parameter sets, 3D models, and analysis scripts are provided for community use. The validated, reactive, and transferable IFF framework facilitates predictive design of MXene-based films, membranes, sensing interfaces, and composites.

MXene↗
DOE OSTI2021

VTO_2021_APR_LLNL_Ye

Traditional batteries are composed of two-dimensional films that are stacked and/or rolled. Thin film batteries display high power density while their thick film counterparts show good energy density, but it has proven difficult to concurrently achieve both within these planar form factors. In addition, conventional Li-ion batteries based on liquid organic electrolytes or gel polymer electrolytes have raised severe safety concerns due to the intrinsic flammable properties of the organic electrolytes. They are also not ideal for the use of high energy density metallic lithium (Li) anodes due to Li dendrite growth, or sulfur cathodes due to shuttling effects that result in fast capacity fade. There is an urgent need to develop safe, high-performance solid-state batteries (SSBs) with advanced electrolyte and separator technologies. Although in recent years a series of superionic conductors have been developed for electrolytes and separators, their performance does not satisfy demanding criteria due to large impedance from poor solid electrolyte-electrode contact and questionable electrochemical and mechanical stability. Unlike the well-established roll-to-roll fabrication of conventional Li-ion batteries, the processing of SSBs is unique due to the brittleness of solid-state electrolytes (SSEs). The commercially available or lab-developed SSE discs are usually very thick (hundreds of micrometers to millimeters) to overcome their brittle nature, which unfortunately increases the cell impedance and accounts for the majority of the overall cell weight and volume, leading to dramatically decreased power and energy densities. In this project, we will investigate 3D printing techniques to overcome safety, fabrication, mechanical, and electrochemical issues in SSBs. 3D printing builds complex structures in a layer-by-layer fashion, which allows rapid production of hierarchical architectures, gradient and multi-material structures, and multi-component assemblies. 3D printing is an emerging area that could fundamentally transform energy storage devices. For example, 3D printing can produce batteries with arbitrary form factors to fit a product’s specific volume requirements and can create interwoven electrode arrangements over a wide range of length scales to improve transport and increase power density for a given energy density. For SSBs, 3D printing may dramatically reduce the separator thickness from ~1 mm (by hydraulic pressing) to tens of micrometers or less. In addition, the interfacial contact area between the electrolyte and the electrode may be increased via 3D interdigitated designs. Hence, we expect a significant reduction of the overall cell impedance and enhancement of both energy and power densities of SSBs by harnessing an array of 3D printing technologies being developed at Lawrence Livermore National Laboratory (LLNL).

25 ENERGY STORAGE↗
DOE OSTI2021

An Environmentally Benign Electrolyte for High Energy Lithium Metal Batteries

In this work, a hybrid electrolyte comprising a high content of H 2 O for a lithium metal cell is reported. At high LiFSI salt concentration, the N-methyl-N-propyl-piperidinium bis(fluorosulfonyl) imide (PMpipFSI) electrolyte can tolerate up to 1 M H2O addition without sacrificing its redox stability on both lithium nickel manganese cobalt oxide (NMC) cathode and lithium metal anode. Molecular dynamics simulations revealed the underpinned mechanism that, at high salt concentrations, H 2 O molecules are embedded in the Li + , PMpip + , and FSI - bulk as a structural material with a strong solvation with Li + and are orderly distributed at the surface of both electrodes. This electrolyte eliminates the critical moisture controls required for the state-of-the-art (SOA) carbonate/LiPF 6 electrolyte, electrode, separator and cell assembly, thus significantly reducing the cost of the mass production of the batteries.

molecular dynamics simulation↗
DOE OSTI2020

Rechargeable alkaline zinc–manganese oxide batteries for grid storage: Mechanisms, challenges and developments

Rechargeable alkaline Zn–MnO 2 (RAM) batteries are a promising candidate for grid-scale energy storage owing to their high theoretical energy density rivaling lithium-ion systems (~400 Wh/L), relatively safe aqueous electrolyte, established supply chain, and projected costs below $100/kWh at scale. In practice, however, many fundamental chemical and physical processes at both electrodes make it difficult to achieve commercially competitive energy density and cycle life. In this paper, we present a detailed and timely analysis of the constituent materials, current commercial status, electrode processes, and performance-limiting factors of RAM batteries. We also examine recently reported strategies in RAM and related systems to address these issues through additives and modifications to the electrode materials and electrolyte, special ion-selective separators and/or coatings, and unconventional cycling protocols. We conclude with a critical summary of these developments and discussion of how future studies should be focused toward the goal of energy-dense, scalable, and cost-effective RAM systems.

25 ENERGY STORAGE↗
DOE OSTI2020

A Fireproof, Lightweight, Polymer–Polymer Solid-State Electrolyte for Safe Lithium Batteries

Safety issues in lithium-ion batteries have raised serious concerns due to their ubiquitous utilization and close contact with the human body. Replacing flammable liquid electrolytes, solid-state electrolytes (SSEs) is thought to address this issue as well as provide unmatched energy densities in Li-based batteries. However, among the most intensively studied SSEs, polymeric solid electrolyte and polymer/ceramic composites are usually flammable, leaving the safety issue unattended. Here, we report the first design of a fireproof, ultralightweight polymer–polymer SSE. The SSE is composed of a porous mechanic enforcer (polyimide, PI), a fire-retardant additive (decabromodiphenyl ethane, DBDPE), and a ionic conductive polymer electrolyte (poly(ethylene oxide)/lithium bis(trifluoromethanesulfonyl)imide). The whole SSE is made from organic materials, with a thin, tunable thickness (10–25 μm), which endorse the energy density comparable to conventional separator/liquid electrolytes. The PI/DBDPE film is thermally stable, nonflammable, and mechanically strong, preventing Li–Li symmetrical cells from short-circuiting after more than 300 h of cycling. LiFePO 4 /Li half cells with our SSE show a high rate performance (131 mAh g –1 at 1 C) as well as cycling performance (300 cycles at C/2 rate) at 60 °C. Most intriguingly, pouch cells made with our polymer–polymer SSE still functioned well even under flame abuse tests.

25 ENERGY STORAGE↗
DOE OSTI2020

LixNiO/Ni Heterostructure with Strong Basic Lattice Oxygen Enables Electrocatalytic Hydrogen Evolution with Pt-like Activity

The low-cost hydrogen production from water electrolysis is crucial for practical deployment of sustainable hydrogen economy, but is often constrained by the lack of active and robust electrocatalysts from Earth-abundant materials. We describe here an unconventional heterostructure composed of strongly coupled Ni-deficient LixNiO nanoclusters and polycrystalline Ni nanocrystals, and its exceptional activities toward hydrogen evolution reaction (HER) in aqueous electrolytes. The presence of unique lattice oxygen species with strong Brønsted basicity is a significant feature, which spontaneously split water molecules and effectively accelerate the sluggish Volmer H-OH dissociation step in neutral and alkaline HER. In combination with the unpreceded level of intimate LixNiO and Ni interfacial junctions that produces abundant “hotspots” for promoted hydride coupling, the catalyst exhibited kinetic activities almost identical as Pt/C and decent long term stability in universal pH.

Lu, Ke↗