SEARCH · Engineering Papers

Results for “constrained control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

NASA NTRS2015

LMI-Based Multiobjective Optimization and Control of Flexible Aircraft Using VCCTEF

This paper considers the control of coupled aeroelastic aircraft model with Variable Camber Continuous Trailing Edge Flap (VCCTEF) system. The relative motion between two adjacent flaps is constrained and this actuation constraint problem is converted into an output covariance constraint problem, and therefore can be formulated using linear matrix inequalities (LMIs). A set of LMI conditions is derived for the design of an observer-based dynamic output feedback controller for VCCTEF configured aeroelastic aircraft model. The proposed controller is then applied to the NASA Generic Transport Model (GTM) for simulation, and the results demonstrate the efficacy of the proposed approach.

LMI control↗

NASA NTRS1982

An advanced generation land mobile satellite system and its critical technologies

A conceptual design for a Land Mobile Satellite System (LMSS) for the 1990s is presented. LMSS involves small tranceivers accessing satellites directly, with ground reception through small car-top antennas. The satellite would have a large antenna and blanket coverage areas in the UHF. The call may originate from a home, be carried by wire to a gateway, transmitted to satellite on the S-band, converted to UHF on the satellite, and transmitted to the vehicle. The system design is constrained by the number of users in an area during the busiest hours, Shuttle storage, controllability factors, and the total area served. A 55-m antenna has been selected, with 87 spot beams and two 10 MHz UHF bands in the 806-890 MHz band. A 17 dB interbeam isolation level is required, implying that sufficient sub-bands can be generated to assure 8265 total channels. The mobile satellite (MSAT) would have an 83 m mast lower segment, a 34 m upper segment, and a second, 10 m antenna made of a deployable mesh. Various antenna function modes are considered.

Naderi, F.↗

NASA NTRS1989

Frequency domain identification experiment on a large flexible structure

Recent experiences in the field of flexible structure control in space have indicated a need for on-orbit system identification to support robust control redesign to avoid in-flight instabilities and maintain high spacecraft performance. The authors highlight an automated frequency domain system identification methodology recently developed to fill this need. The methodology supports (1) the estimation of system quantities useful for robust control analysis and design, (2) experiment design tailored to performing system identification in a typically constrained on-orbit environment, and (3) the automation of operations to reduce human-in-the-loop requirements. A basic overview of the methodology is presented first, followed by an experimental verification of the approach performed on the JPL/AFAL testbed facility.

Bayard, D. S.↗

NASA NTRS1991

Automated on-orbit frequency domain identification for large space structures

Recent experiences in the field of flexible structure control in space have indicated a need for on-orbit system identification to support robust control redesign to avoid in-flight instabilities and maintain high spacecraft performance. This paper highlights an automated frequency domain system identification methodology recently developed to fulfill this need. The methodology is focused to support (1) the estimation of system quantities useful for robust control analysis and design; (2) experiment design tailored to performing system identification in a typically constrained on-orbit environment; and (3) the automation of operations to reduce 'human in the loop' requirements.

Bayard, D. S.↗

NASA NTRS1994

Development of homotopy algorithms for fixed-order mixed H2/H(infinity) controller synthesis

A major difficulty associated with H-infinity and mu-synthesis methods is the order of the resulting compensator. Whereas model and/or controller reduction techniques are sometimes applied, performance and robustness properties are not preserved. By directly constraining compensator order during the optimization process, these properties are better preserved, albeit at the expense of computational complexity. This paper presents a novel homotopy algorithm to synthesize fixed-order mixed H2/H-infinity compensators. Numerical results are presented for a four-disk flexible structure to evaluate the efficiency of the algorithm.

Whorton, M.↗

NASA NTRS2022

Europa Clipper Mission: System Integration Review Report

Jupiter’s icy moon Europa is a prime target in our exploration of potentially habitable worlds beyond Earth. The combination of a subsurface liquid water layer in contact with a rocky seafloor may yield an ocean rich in the elements and energy needed for the emergence of life, and for potentially sustaining life through time. Europa may hold the clues to one of NASA’s long-standing quests – to determine whether or not we are alone in the universe. The Europa Clipper mission will characterize Europa’s habitability as the first step in the search for potential life at Europa by conducting approximately four dozen flybys. The project is preparing for a System Integration Review in November of 2021. This paper will summarize changes from the mission’s Preliminary Design Review (PDR) baseline, including science objectives, launch vehicle, interplanetary trajectory, science tour, flight system, payload and mission phases. Since PDR several of the Level 1 science requirements were descoped and the science requirement flow was realigned, in order to control cost growth. The realignment deemphasized science redundancy, which had resulted in an over-constrained science tour, in favor of a more targeted linkage to the primary responding instrument. Additionally, changes to the PDR flight system design baseline include changes to the sounding radar antenna design, the magnetometer architecture, and the heat redistribution system pumps. All changes have been incorporated into a reference science tour used to demonstrate that the requirements and design of the flight system and payload are mature enough to support flight builds.

Cook, Kendra↗

NASA NTRS2000

SMA Hybrid Composites for Dynamic Response Abatement Applications

A recently developed constitutive model and a finite element formulation for predicting the thermomechanical response of Shape Memory Alloy (SMA) hybrid composite (SMAHC) structures is briefly described. Attention is focused on constrained recovery behavior in this study, but the constitutive formulation is also capable of modeling restrained or free recovery. Numerical results are shown for glass/epoxy panel specimens with embedded Nitinol actuators subjected to thermal and acoustic loads. Control of thermal buckling, random response, sonic fatigue, and transmission loss are demonstrated and compared to conventional approaches including addition of conventional composite layers and a constrained layer damping treatment. Embedded SMA actuators are shown to be significantly more effective in dynamic response abatement applications than the conventional approaches and are attractive for combination with other passive and/or active approaches.

Turner, Travis L.↗

NASA NTRS2020

Constraining Remote Oxidation Capacity with ATom Observations

The global oxidation capacity, defined as the tropospheric mean concentration of the hydroxyl radical (OH), controls the lifetime of reactive trace gases in the atmosphere such as methane and carbon monoxide (CO). Models tend to underestimate the methane lifetime and CO concentrations throughout the troposphere, which is consistent with excessive OH. Approximately half the oxidation of methane and non-methane volatile organic compounds (VOCs) is thought to occur over the oceans where oxidant chemistry has received little validation due to a lack of observational constraints. We use observations from the first two deployments of the NASA ATom aircraft campaign during July–August 2016 and January–February 2017 to evaluate the oxidation capacity over the remote oceans and its representation in the GEOS-Chem chemical transport model. The model successfully simulates the magnitude and vertical profile of remote OH within the measurement uncertainties. Comparisons against the drivers of OH production (water vapor, ozone, and NOy concentrations, ozone photolysis frequencies) also show minimal bias with the exception of wintertime NOy, for which a model overestimate may indicate insufficient wet scavenging and/or missing loss on seasalt aerosol but large uncertainties remain that require further studies of NOy partitioning and removal in the troposphere. During the ATom-1 deployment, OH reactivity (OHR) below 3 km is significantly enhanced, and this is not captured by the sum of its measured components (cOHRobs) or by the model (cOHRmod). This enhancement could suggest missing reactive VOCs but cannot be explained by new estimates of ocean VOC sources and additional modeled reactivity in this region would be difficult to reconcile with the full suite of ATom measurement constraints. The model generally reproduces the magnitude and seasonality of cOHRobs but underestimates the contribution of oxygenated VOC, mainly acetaldehyde, which is severely underestimated throughout the troposphere despite its calculated lifetime of less than a day. Missing model acetaldehyde in previous studies was attributed to measurement uncertainties that have been largely resolved. Observations of peroxyacetic acid (PAA) provide new support for remote levels of acetaldehyde. The underestimate in modeled acetaldehyde and PAA is present throughout the year in both hemispheres and peaks during Northern Hemisphere summer. The addition of ocean VOC sources in the model increases annual surface cOHRmod by 10 % and improves model-measurement agreement for acetaldehyde particularly in winter but cannot resolve the model summertime bias. Doing so would require a 100 Tg yr−1 source of a long-lived unknown precursor throughout the year with significant additional emissions in the Northern Hemisphere summer. Improving the model bias for remote acetaldehyde and PAA is unlikely to fully resolve previously reported model global biases in OH and methane lifetime, suggesting that future work should examine the sources and sinks of OH over land.

Travis, Katherine R.↗

NASA NTRS1978

Characteristics of constrained optimum trajectories with specified range

Necessary conditions of optimality are derived for trajectories whose structure is limited to climb, steady cruise, and descent segments. The performance function consists of the sum of fuel and time costs, referred to as direct operating cost (DOC). The state variable is range to go and the independent variable is energy. In this formulation a cruise segment always occurs at the optimum cruise energy for sufficiently large range. At short ranges (500 n. mi. and less) a cruise segment may also occur below the optimum cruise energy. The existence of such a cruise segment depends primarily on the fuel flow vs thrust characteristics and on thrust constraints. If thrust is a free control variable along with airspeed, it is shown that such cruise segments will not generally occur. If thrust is constrained to some maximum value in climb and to some minimum in descent, such cruise segments generally will occur. Computer calculations of typical short-range trajectories obtained about a 1% cost penalty for constraining the thrust.

Erzberger, H.↗

NASA NTRSDate not supplied

Update on Subsonic Single Aft Engine (SUSAN) Electrofan Trade Space Exploration

NASA is conducting an ongoing trade study analysis of the SUSAN Electrofan aircraft concept, which utilizes 20-MW-class electrified aircraft propulsion to enable propulsive, aerodynamic, and control benefits while retaining the range, speed, and size of typical narrow-body regional aircraft. The study is constrained by the ground rules of operating within the current airport and airspace infrastructure. This ongoing study seeks to find a configuration and combination of technologies that yield significant fuel burn and emissions benefits. Another key goal is to reduce cost per passenger mile. Currently, the study is focused on a configuration that utilizes jet A or sustainable aviation fuels, however, we plan to consider other fuel alternatives in the future. This paper describes the progress in defining the architecture of the aircraft, engine, power system, control system, and initial understandings of the sensitivity of the potential configurations to technology assumptions based on key performance parameters. Additionally, progress towards definition and refinement of driving operational, economic, infrastructure, certification, and technical requirements is discussed.

aircraft concept↗

NASA NTRSDate not supplied

Update on Subsonic Single Aft Engine (SUSAN) Electrofan Trade Space Exploration

NASA is conducting an ongoing trade study analysis of the SUSAN Electrofan aircraft concept, which utilizes 20-MW-class electrified aircraft propulsion to enable propulsive, aerodynamic, and control benefits while retaining the range, speed, and size of typical narrow-body regional aircraft. The study is constrained by the ground rules of operating within the current airport and airspace infrastructure. This ongoing study seeks to find a configuration and combination of technologies that yield significant fuel burn and emissions benefits. Another key goal is to reduce cost per passenger mile. Currently, the study is focused on a configuration that utilizes jet A or sustainable aviation fuels, however, we plan to consider other fuel alternatives in the future. This presentation describes the progress in defining the architecture of the aircraft, engine, power system, control system, and initial understandings of the sensitivity of the potential configurations to technology assumptions based on key performance parameters. Additionally, progress towards definition and refinement of driving operational, economic, infrastructure, certification, and technical requirements is discussed.

Ralph H. Jansen↗

NASA NTRS1961

Guidance and Control During Direct-Descent Parabolic Reentry

The results of studies of four reentry guidance and control techniques for the energy management of vehicles returning to the earth at escape speeds are compared in this paper. The reentry trajectories are constrained to those of direct descent, that is, where the vehicle does not leave that portion of the atmosphere where useful aerodynamic forces are available after its initial entry. The guidance techniques compared are: (1) a piloted simulator study reference trajectory techniques; 2) An automatic controller using reference trajectory techniques; 3) A predictor system employing linear prediction (perturbation) techniques; and 4) A repetitive prediction system employing rapid-time computer techniques.

Foudriat, Edwin C.↗

NASA NTRS2017

Wheels-Off Time Uncertainty Impact on Benefits of Early Call for Release Scheduling

Arrival traffic scenarios with 808 flights from 173 airports to Houston George Bush International airport are simulated to determine if Call For Release flights can receive a benefit in terms of less delay over other flights by scheduling prior to gate pushback (look-ahead in time) as opposed to at gate pushback. Call for Release flights are departures that require approval from Air Route Traffic Control Center prior to release. Realism is brought to the study by including gate departure delay and taxi-out delay uncertainties for the 77 major U. S. airports. Gate departure delay uncertainty is assumed to increase as a function of look-ahead time. Results show that Call For Release flights from an airport within the freeze horizon (a region surrounding the arrival airport) can get an advantage over other flights to a capacity constrained airport by scheduling prior to gate pushback, provided the wheels-off time uncertainty with respect to schedule is controlled to a small value, such as within a three-minute window. Another finding of the study is that system delay, measured as the sum of arrival delays, is smaller when flights are scheduled in the order of arrival compared to in the order of departure. Because flights from airports within the freeze horizon are scheduled in the order of departure, an increase in the number of internal airports with a larger freeze horizon increases system delay. Delay in the given scenario was found to increase by 126% (from 13.8 hours to 31.2 hours) as freeze horizon was increased from 30-minutes to 2-hours in the baseline scenario.

wheels-off time uncertainty↗

NASA NTRS1991

Exact and explicit optimal solutions for trajectory planning and control of single-link flexible-joint manipulators

An optimal trajectory planning problem for a single-link, flexible joint manipulator is studied. A global feedback-linearization is first applied to formulate the nonlinear inequality-constrained optimization problem in a suitable way. Then, an exact and explicit structural formula for the optimal solution of the problem is derived and the solution is shown to be unique. It turns out that the optimal trajectory planning and control can be done off-line, so that the proposed method is applicable to both theoretical analysis and real time tele-robotics control engineering.

Chen, Guanrong↗

NASA NTRSDate not supplied

Scaling Climbing Collaborative Mobile Manipulators (C2M2) for Outfitting a Tall Lunar Tower (TLT) and Truss Structures

In-space and planetary truss structures like the Tall Lunar Tower (TLT) can greatly benefit from truss climbing collaborative mobile manipulators (C-CMMs) for outfitting and other servicing tasks. Mobile robotic systems traversing these structures will allow for improved access to the structure for placing equipment and routing cables after the structure has been assembled. The robotic system described in the proposed paper is designed to provide access to the structure through collaborative mobile robotics. The paper will provide a method to constrain the design of such a robot via the geometry of the truss structure and the controlling joint torques across various gaits. The focus of the design is on a six-degree of freedom (DOF) robot arranged with two-DOF at each end and at the center. The variable features of this system are the actuators and the length of the links connecting the two-DOF modules. The result of the analysis is a link sizing range which the robot can be designed within to ensure functionality on the truss structure. A C-CMM will be designed using the scaling utility and several constructed to demonstrate operating both independently and collaboratively.

in-space assembly↗

NASA NTRSDate not supplied

Improving Kinetic Consistency Across Elastic Model Transitions With Quadratic Inequality Constrained Weighted Least Squares (WLSQI)

Flexible body modeling presents a large challenge in the development of simulations to aid in design of flight control systems for launch and landing vehicles. Typically, the flexible body model is not a single continuous model but are rather discrete sets of Linear Time Invariant (LTI) Finite Element Models (FEM) incremented by propellant levels. This introduces the problem of smoothly transitioning modal and physical states of the vehicle when switching from one FEM to the next. This paper introduces a new approach to optimally transition flexible body states with weighted least squares, building off previous methods.

Convex Optimization↗

NASA NTRSDate not supplied

Improving Kinetic Consistency Across Elastic Model Transitions With Quadratic Inequality Constrained Weighted Least Squares (WLSQI)

GN&C↗

NASA NTRS1989

CONSOLE: A CAD tandem for optimization-based design interacting with user-supplied simulators

CONSOLE employs a recently developed design methodology (International Journal of Control 43:1693-1721) which provides the designer with a congenial environment to express his problem as a multiple ojective constrained optimization problem and allows him to refine his characterization of optimality when a suboptimal design is approached. To this end, in CONSOLE, the designed formulates the design problem using a high-level language and performs design task and explores tradeoff through a few short and clearly defined commands. The range of problems that can be solved efficiently using a CAD tools depends very much on the ability of this tool to be interfaced with user-supplied simulators. For instance, when designing a control system one makes use of the characteristics of the plant, and therefore, a model of the plant under study has to be made available to the CAD tool. CONSOLE allows for an easy interfacing of almost any simulator the user has available. To date CONSOLE has already been used successfully in many applications, including the design of controllers for a flexible arm and for a robotic manipulator and the solution of a parameter selection problem for a neural network.

Fan, Michael K. H.↗