Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cavitation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Durability Study of a High-Pressure Common Rail Fuel Injection System Using Lubricity Additive-Dosed Gasoline-Like Fuel—Improved Endurance with Upgraded Hardware

Gasoline compression ignition (GCI) is a promising combustion technology that can help the commercial transportation sector achieve operational flexibility and meet upcoming criteria pollutant regulations. However, high-pressure fuel injection systems (>1000 bar) are needed to enable GCI and fully realize its benefits compared to conventional diesel combustion. This work is a continuation of previous durability studies that identified three key technical risks after running gasoline-like fuel through a heavy-duty, common rail injection system: (i) cavitation damage to the inlet check valve of the high-pressure pump, (ii) loss of injector fueling capacity, (iii) cavitation erosion of the injector nozzle holes. Upgraded hardware solutions were tested on a consistent 400- to 800-hour NATO durability cycle with the same gasoline-like fuel as previous studies. The upgraded pump showed no signs of abnormal wear or cavitation damage to the inlet check valve. In contrast to previous studies, there were no signs of pump performance degradation observed after 400 hours of testing. Material selection and design upgrades were also made to the injector which, only showed a 6.5% loss in fueling capacity after 800 hours of durability testing compared to 49.3% previously. Finally, geometric nozzle hole features such as higher inlet radius of curvature and higher K-factor were found to correlate with reduced cavitation erosion. However, mitigation of eccentric radial needle motion (i.e., wobble) is likely needed to further suppress cavitation. In general, the results from this study indicate there are viable hardware-based solutions for improving the endurance of high-pressure systems when running with gasoline-like fuel.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1972

Empirical evaluation of pump inlet compliance

Cavitation compliance was determined experimentally from pulsing tests on a number of rocket turbopumps. The primary test data used for this study are those for the Rocketdyne H-1, F-1, and J-2 oxidizer and fuel pumps employed on Saturn vehicles. The study shows that these data can be correlated by a particular form of nondimensionalization, the key feature of which is to divide the operating cavitation number or suction specific speed by its value at head breakdown. An expression is obtained for a best-fit curve for these data. Another set of test data for the Aerojet LR87 and 91 pumps can be correlated by a somewhat different nondimensional pump performance parameter, specifically by relating the cavitation number to its position between the head breakdown point and the point of zero slope of the head coefficient versus cavitation number. Recommendations are given for the estimation of the cavitation compliance for new designs in the Rocketdyne family of pumps.

Ghahremani, F. G.↗
NASA NTRS1988

The use of multigrid techniques in the solution of the Elrod algorithm for a dynamically loaded journal bearing

A numerical solution to a theoretical model of vapor cavitation in a dynamically loaded journal bearing is developed, utilizing a multigrid iterative technique. The code is compared with a presently existing direct solution in terms of computational time and accuracy. The model is based on the Elrod algorithm, a control volume approach to the Reynolds equation which mimics the Jakobssen-Floberg and Olsson cavitation theory. Besides accounting for a moving cavitation boundary and conservation of mass at the boundary, it also conserves mass within the cavitated region via liquid striations. The mixed nature of the equations (elliptic in the full film zone and nonelliptic in the cavitated zone) coupled with the dynamic aspects of the problem create interesting difficulties for the present solution approach. Emphasis is placed on the methods found to eliminate solution instabilities. Excellent results are obtained for both accuracy and reduction of computational time.

Woods, Claudia M.↗
NASA NTRS1988

The solution of the Elrod algorithm for a dynamically loaded journal bearing using multigrid techniques

A numerical solution to a theoretical model of vapor cavitation in a dynamically loaded journal bearing is developed utilizing a multigrid iteration technique. The method is compared with a noniterative approach in terms of computational time and accuracy. The computational model is based on the Elrod algorithm, a control volume approach to the Reynolds equation which mimics the Jakobsson-Floberg and Olsson cavitation theory. Besides accounting for a moving cavitation boundary and conservation of mass at the boundary, it also conserves mass within the cavitated region via a smeared mass or striated flow extending to both surfaces in the film gap. The mixed nature of the equations (parabolic in the full film zone and hyperbolic in the cavitated zone) coupled with the dynamic aspects of the problem create interesting difficulties for the present solution approach. Emphasis is placed on the methods found to eliminate solution instabilities. Excellent results are obtained for both accuracy and reduction of computational time.

Woods, Claudia M.↗
NASA NTRS1989

The solution of the Elrod algorithm for a dynamically loaded journal bearing using multigrid techniques

A numerical solution to a theoretical model of vapor cavitation in a dynamically loaded journal bearing is developed utilizing a multigrid iteration technique. The method is compared with a noniterative approach in terms of computational time and accuracy. The computational model is based on the Elrod algorithm, a control volume approach to the Reynolds equation which mimics the Jakobsson-Floberg and Olsson cavitation theory. Besides accounting for a moving cavitation boundary and conservation of mass at the boundary, it also conserves mass within the cavitated region via a smeared mass or striated flow extending to both surfaces in the film gap. The mixed nature of the equations (parabolic in the full film zone and hyperbolic in the cavitated zone) coupled with the dynamic aspects of the problem create interesting difficulties for the present solution approach. Emphasis is placed on the methods found to eliminate solution instabilities. Excellent results are obtained for both accuracy and reduction of computational time.

Woods, C. M.↗
NASA NTRS2012

Investigation of Turbulent Tip Leakage Vortex in an Axial Water Jet Pump with Large Eddy Simulation

Detailed steady and unsteady numerical studies were performed to investigate tip clearance flow in an axial water jet pump. The primary objective is to understand physics of unsteady tip clearance flow, unsteady tip leakage vortex, and cavitation inception in an axial water jet pump. Steady pressure field and resulting steady tip leakage vortex from a steady flow analysis do not seem to explain measured cavitation inception correctly. The measured flow field near the tip is unsteady and measured cavitation inception is highly transient. Flow visualization with cavitation bubbles shows that the leakage vortex is oscillating significantly and many intermittent vortex ropes are present between the suction side of the blade and the tip leakage core vortex. Although the flow field is highly transient, the overall flow structure is stable and a characteristic frequency seems to exist. To capture relevant flow physics as much as possible, a Reynolds-averaged Navier-Stokes (RANS) calculation and a Large Eddy Simulation (LES) were applied for the current investigation. The present study reveals that several vortices from the tip leakage vortex system cross the tip gap of the adjacent blade periodically. Sudden changes in local pressure field inside tip gap due to these vortices create vortex ropes. The instantaneous pressure filed inside the tip gap is drastically different from that of the steady flow simulation. Unsteady flow simulation which can calculate unsteady vortex motion is necessary to calculate cavitation inception accurately even at design flow condition in such a water jet pump.

Hah, Chunill↗
DOE OSTI2025

Creep ductility limiting mechanisms in an additively manufactured Al-Ce-Ni-Mn-Zr alloy

Tensile creep response and cavitation damage evolution in an additively manufactured Al-7.5Ce-4.5Ni-0.4Mn-0.7Zr (wt%) alloy with peak-aging and overaging treatments were investigated in the 300–400 ºC range. Microstructural heterogeneity and its response to heat treatment and subsequent creep deformation were studied to understand the interplay between cavity formation, creep lifetime and ductility. Increasing the applied stress activated the nucleation of more cavities, an experimental observation that is well described using the vacancy accumulation model. Cavities nucleated prematurely due to localized plasticity in the denuded zones that formed at/near melt-pool or grain boundaries. Microstructure/deformation heterogeneity with consequent evolution of stress triaxiality, especially at lower stresses, causes accelerated cavitation, thus producing low creep ductility (∼ 0.2–2.4 %), compared to (∼12–21 %) ductility of the alloy measured by regular tensile tests at equivalent temperatures. A constrained diffusional cavity growth mechanism with continuous cavity nucleation during creep is established as the dominant mechanism, implying that cavitation involves vacancy diffusion, yet its growth rate is dictated by the minimum creep rate. In conclusion, the ductility-limiting creep and cavitation mechanisms discussed here provide new insight into the creep behavior of 3D-printed metallic alloys.

Additive manufacturing↗
DOE OSTI2025

Influence of Pore Water on the Fracture of Silica Sand at Particle Scale

The fracture of particles has a significant influence on the engineering behavior of granular materials. There are no reported conclusive answers in the literature to explain the influence of pore water on the fracture of sand, gravel, railroad ballast rock, aggregates, rockfill, and so on. Here, in this paper, two novel techniques were adopted to investigate the influence of pore water on the fracture of natural silica sand at the particle scale. The three-dimensional (3D) synchrotron microcomputed tomography (SMT) imaging technique was used to acquire and analyze multiple 3D images of specimens composed of wetted silica sand that were subjected to confined one-dimensional (1D) compression loading up to the fracture stage. A few representative particles were identified and digitally separated from the liquid water and gas phases. The 3D SMT images offer clear experimental evidence of the phase transition of water from liquid to gas within the opening cracks. In addition, a computational fluid dynamics numerical simulation framework for water flow into an opening crack was adopted and the results show that the fast opening of the crack induced cavitation, water phase transition, and water hammer effects. The results of the numerical simulations agree with the confined 1D compression experiments where the onset of the bubbles (gas phase) within the crack is mainly generated during the secondary cavitation stage, and the generated bubble near the crack mouth opening resulted from the primary cavitation, which was directly caused by the crack expansion. The results reported in this paper present a new cavitation phenomenon that occurs during particle fracture, which offers a physics-based explanation of why water-wetted sand fractures at smaller stresses than dry and can pave the way for more in-depth future studies on the fracture of water-wetted sand.

cavitation↗
DOE OSTI2022

Subdiffusive High-Pressure Hydrogen Gas Dynamics in Elastomers

We report elastomeric rubber materials serve a vital role as sealing materials in the hydrogen storage and transport infrastructure. With applications including O-rings and hose liners, these components are exposed to pressurized hydrogen at a range of temperatures, cycling rates, and pressure extremes. High-pressure exposure and subsequent rapid decompression often lead to cavitation and stress-induced damage of the elastomer due to localization of the hydrogen gas. Here, we use all-atom classical molecular dynamics simulations to assess the impact of compositional variations on gas diffusion within the commonly used elastomer ethylene–propylene–diene monomer (EPDM). With the aim to build a predictive understanding of precursors to cavitation and to motivate material formulations that are less sensitive to hydrogen-induced failure, we perform systematic simulations of gas dynamics in EPDM as a function of temperature, gas concentration, and cross-link density. Our simulations reveal anomalous, subdiffusive hydrogen motion at pressure and intermediate times. We identify two groups of gas with different mobilities: one group exhibiting high mobility and one group exhibiting low mobility due to their motion being impeded by the polymer. With decreasing temperatures, the low-mobility group shows increased gas localization, the necessary precursor for cavitation damage in these materials. At lower temperatures, increasing cross-link density led to greater hydrogen gas mobility and a lower fraction of caged hydrogen, indicating that increasing cross-link density may reduce precursors to cavitation. Finally, we use a two-state kinetic model to determine the energetics associated with transitions between these two mobility states.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Liquid-phase mixing of bipropellant doublets

Experimental results of unlike doublet mixing are correlated with an analytically derived equation predicting fluid cavitation. The correlation relates the minimum orifice pressure drop required to initiate cavitation, with the system back pressure, cold flow simulant vapor pressure, and the orifice flow discharge and contraction coefficients. Stream flow instabilities are also visually correlated with the onset of cavitation and orifice discharge coefficient measurements. The influence of cavitation on the characteristic phenomenon of hydraulic flip is observed for both circular and noncircular shaped orifices. For certain intermediate orifice lengths, some noncircular shapes are shown to produce more fully developed flows (shorter recovery lengths) and therefore a more cohesive jet, which in turn yields slightly higher cold flow mixing uniformities than circular shaped orifices of equal absolute length. The particular noncircular shaped elements evaluated are shown to be more sensitive to liquid stream misimpingement than the corresponding circular orifices.

Hoehn, F. W.↗
NASA NTRS1973

A note on the unsteady cavity flow in a tunnel

The unsteady internal cavitating flow such as the one observed in a pump or a turbine is studied for a simple two-dimensional model of a base-cavitating wedge in an infinite tunnel and it is shown how the cavitation compliance can be calculated using the linearized free streamline theory. Numerical values are obtained for the limiting case of a free jet. Two important features are: First, the cavitation compliance is found to be of complex form, having additional resistive and reactive terms beyond the purely inertial oscillation of the whole channel in 'slug flow.' Second, the compliance has a strong dependence on frequency.

Kim, J. H.↗
NASA NTRS1991

Measurements of Pressure Distributions and Force Coefficients in a Squeeze Film Damper. Part 2: Partially Sealed Configuration

Experimental results from a partially sealed squeeze film damper (SFD) test rig, executing a circular centered orbit are presented and discussed. A serrated piston ring is installed at the damper exit. This device involves a new sealing concept which produces high damping values while allowing for oil flow to cool the damper. In the partially sealed damper, large cavitation regions are observed in the pressure fields at orbit radii epsilon equals 0.5 and epsilon equals 0.8. The cavitated pressure distributions and the corresponding force coefficients are compared with a cavitated bearing solution. The experimental results show the significance of fluid inertia and vapor cavitation in the operation of squeeze film dampers. Squeeze film Reynolds numbers tested reach up to Re equals 50, spanning the range of contemporary applications.

Jung, S. Y.↗
NASA NTRS1992

Combustion of LOX with H2(sub g) under subcritical, critical, and supercritical conditions and experimental observation of dense spray and mixing of impinging jets

Progress made during the period of February 1 to October 15, 1992 is reported. The overall objective of Task 1 of the investigation is to achieve a better understanding of the combustion processes of liquid oxygen and gaseous hydrogen under subcritical, critical, and supercritical conditions. Specific objectives of the research program are: (1) to determine the evaporation- and burning-rate characteristics of LOX in hydrogen/helium environments under broad ranges of operating conditions; (2) to measure species concentration profile and surface temperature of LOX employing the gas chromatography and fine-wire thermocouples under non-reacting flow situations; (3) to perform a fugacity-based multicomponent thermodynamic phase equilibrium analysis for examining the high-pressure vapor-liquid equilibrium behavior at the liquid surface of LOX; (4) to formulate and solve a theoretical model for simulating the evaporation and combustion processes in a LOX/H2/He system; and (5) to validate the theoretical model with the measured experimental data. Task 2 of the investigation is described. Observation of a like-on-like injector element in the near-injector region performed in the previous phase of this project has identified the existence of a high Reynolds number regime in which the pre-impingement jets are fully turbulent and undergoing surface breakup. The new spray regime, which has not been observed by previous investigators, is characterized by the presence of many fine droplets and the disappearance of the well-defined liquid breakup wave pattern in the post-impingement region. It is speculated that a cavitating region may be present within the orifice so that it could induce strong turbulence, leading to an onset of atomization of the jets prior to impingement. To further investigate the dense spray behavior of the impinging jets in the high Reynolds number region, experiments were conducted using Plexiglas injector components for direct internal flow observation. The main objective is to determine under what conditions a cavitating region would form and whether or not the cavitation is reponsible for the development of the high Reynolds number spray regime. The procedure and major findings of the injector cavitation study are described.

Kuo, Kenneth K.↗
NASA NTRS1959

Hydrodynamic Characteristics of Two Low-Drag Supercavitating Hydrofoils

An experimental investigation has been conducted in Langley tank no. 2 to determine the hydrodynamic characteristics of two low-drag supercavitating hydrofoils operating in a range of cavitation numbers from 0 to approximately 6. The hydrofoils had aspect ratios of 1 and 3, and the sections were derived by assuming five terms in the vorticity-distribution expansion of the equivalent airfoil. The aspect-ratio-1 hydrofoil was also tested at zero cavitation number with two sets of end plates having depths of 3/8 and 1/4 chords. Zero cavitation number was established by operating the hydrofoils near the water surface so that complete ventilation of the upper surfaces could be obtained. For those depths of submersion where complete ventilation was not obtained through vortex ventilation, two probes were used to introduce air to the upper surfaces of the hydrofoils and to induce complete ventilation. Data were obtained for a range of speeds from 20 to 80 fps, angles of attack from 2 to 20 deg, and ratios of depth of submersion to chord from 0 to 0.85. The experimental results obtained from the aspect-ratio-1 and aspect-ratio-3, five-term hydrofoils were compared with a three-dimensional zero-cavitation-number theory. The theoretical and experimental values of lift and center of pressure for the aspect-ratio-1 hydrofoil were in agreement, within engineering accuracy, for the range of lift coefficients investigated. The theoretical drag coefficients were lower, by a constant amount, than the experimental drag coefficients. The theoretical expressions derived for the lift, drag, and center of pressure of the aspect-ratio-3 hydrofoil were in agreement, within engineering accuracy, with the experimental values. The theoretical and experimental drag coefficients of the aspect-ratio-3 five-term hydrofoil were lower than the theoretical drag coefficients computed for a comparable Tulin-Burkart hydrofoil.

McGehee, John R.↗
NASA NTRS1998

Transient Simulation of Pressure Oscillations in the Fuel Feedline of the Fastrac Engine Thrust Chamber

During mainstage testing of the 60,000 lbf thrust Fastrac thrust chamber at MSFC's Test Stand 116 (TS 116), sustained, large amplitude oscillations near 530 Hz were observed in the pressure data. These oscillations were detected both in the RP-1 feedline, downstream of the cavitating venturi, and in the combustion chamber. The driver of the instability is believed to be feedline excitation driven by either periodic cavity collapse at the exit of the cavitating venturi or combustion instability. In covitating venturi, static pressure drops as the flow passes through a constriction resembling a converging-diverging nozzle until the vapor pressure is reached. At the venturi throat, the flow is essentially choked, which is why these devices are typically used for mass flow rate control and disturbance isolation. Typically, a total pressure drop of 15% or more across the venturi is required for cavitation. For much larger pressure differentials, unstable cavities can form and subsequently collapse downstream of the throat. Although the disturbances generated by cavitating venturis is generally considered to be broad-band, this type of phenomena could generate periodic behavior capable of exciting the feedline. An excitation brought about by combustion instability would result from the coupling of a combustion chamber acoustic mode and a feedline resonance frequency. This type of coupling is referred to as "buzz" and is not uncommon for engines in this thrust range.

Bullard, Brad↗
NASA NTRS2002

Introductory Remarks for ISROMAC-9 Panel on Inducer Design Criteria

The Space Shuttle Main Engine (SSME) High Pressure Oxygen Turbopump (HPOTP) inducer cavitation study was initiated in the mid 1990s to support high synchronous vibrations. A Fastrac 60K Engine Oxygen Turbopump inducer cavitation study was started around the same time to support a blade deformation investigation. Super-synchronous rotating, attached synchronous, and pronounced subsynchronous flow oscillations were evident. Current thrusts in experimental work include characterization of loads induced by the various forms of cavitation inducted stabilities and measurements of cavitating turbopump dynamic transfer functions.

Zoladz, Tom↗
NASA NTRS2010

Investigating Dynamics of Eccentricity in Turbomachines

A methodology (and hardware and software to implement the methodology) has been developed as a means of investigating coupling between certain rotordynamic and hydrodynamic phenomena in turbomachines. Originally, the methodology was intended for application in an investigation of coupled rotordynamic and hydrodynamic effects postulated to have caused high synchronous vibration in the space shuttle s high-pressure oxygen turbopump (HPOTP). The methodology can also be applied in investigating (for the purpose of developing means of suppressing) undesired hydrodynamic rotor/stator interactions in turbomachines in general. The methodology and the types of phenomena that can be investigated by use of the methodology are best summarized by citing the original application as an example. In that application, in consideration of the high synchronous vibration in the space-shuttle main engine (SSME) HPOTP, it was determined to be necessary to perform tests to investigate the influence of inducer eccentricity and/or synchronous whirl motion on inducer hydrodynamic forces under prescribed flow and cavitation conditions. It was believed that manufacturing tolerances of the turbopump resulted in some induced runout of the pump rotor. Such runout, if oriented with an inducer blade, would cause that blade to run with tip clearance smaller than the tip clearances of the other inducer blades. It was hypothesized that the resulting hydraulic asymmetry, coupled with alternating blade cavitation, could give rise to the observed high synchronous vibration. In tests performed to investigate this hypothesis, prescribed rotor whirl motions have been imposed on a 1/3-scale water-rig version of the SSME LPOTP inducer (which is also a 4-biased inducer having similar cavitation dynamics as the HPOTP) in a magnetic-bearing test facility. The particular magnetic-bearing test facility, through active vibration control, affords a capability to impose, on the rotor, whirl orbits having shapes and whirl rates prescribed by the user, and to simultaneously measure the resulting hydrodynamic forces generated by the impeller. Active control also made it possible to modulate the inducer-blade running tip clearance and consequently effect alternating blade cavitation. The measured hydraulic forces have been compared and correlated with shroud dynamic-pressure measurements.

Baun, Daniel↗
NASA NTRS2004

Routines for Computing Pressure Drops in Venturis

A set of computer-program routines has been developed for calculating pressure drops and recoveries of flows through standard venturis, nozzle venturis, and orifices. Relative to prior methods used for such calculations, the method implemented by these routines offers greater accuracy because it involves fewer simplifying assumptions and is more generally applicable to wide ranges of flow conditions. These routines are based on conservation of momentum and energy equations for real nonideal fluids, the properties of which are calculated by curve-fitting subroutines based on empirical properties data. These routines are capable of representing cavitating, choked, non-cavitating, and unchoked flow conditions for liquids, gases, and supercritical fluids. For a computation of flow through a given venturi, nozzle venturi, or orifice, the routines determine which flow condition occurs: First, they calculate a throat pressure under the assumption that the flow is unchoked or non-cavitating, then they calculate the throat pressure under the assumption that the flow is choked or cavitating. The assumption that yields the higher throat pressure is selected as the correct one.

de Quay, Laurence↗