Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “YOUNG MODULUS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Radiation tolerance of ultra-thin Formvar films

Mechanical behavior of free-standing polymer films with submicron thicknesses exposed to a radiation environment is poorly understood. Here, we study 110-nm-thin free-standing polyvinyl formal (Formvar) films irradiated at room temperature with 1-5 keV electrons or 3 MeV alpha particles. We measure mechanical properties and the elemental composition by spherical indentation and high-energy ion scattering, respectively. Results show that, with increasing radiation dose, the effective failure strain and film thickness decrease monotonically, while the dose dependence of the Young's modulus is non-monotonic. The failure strain and modulus scale with the average energy deposited in the film, while the film thickness exhibits a more complex behavior.

36 MATERIALS SCIENCE↗

Effect of cobalt doping on the mechanical properties of ZnO nanowires

In this work, we investigate the influence of doping on the mechanical properties of ZnO nanowires (NWs) by comparing the mechanical properties of pure and Co-doped ZnO NWs grown in similar conditions and having the same crystallographic orientation [0001]. The mechanical characterization included three-point bending tests made with atomic force microscopy and cantilever beam bending tests performed inside scanning electron microscopy. It was found that the Young's modulus of ZnO NWs containing 5% of Co was approximately a third lower than that of the pure ZnO NWs. Bending strength values were comparable for both materials and in both cases were close to theoretical strength indicating high quality of NWs. Dependence of mechanical properties on NW diameter was found for both doped and undoped ZnO NWs. - Highlights: •Effect of Co doping on the mechanical properties of ZnO nanowires is studied. •Co substitutes Zn atoms in ZnO crystal lattice. •Co addition affects crystal lattice parameters. •Co addition results in significantly decreased Young's modulus of ZnO. •Bending strength for doped and undoped wires is close to the theoretical strength.

36 MATERIALS SCIENCE↗

Microstructural characterisation of nanocomposite nc-MeC/a-C coatings on oxygen hardened Ti-6Al-4V alloy

Nanocomposite coatings are novel, important systems composed of two or more nanocrystalline, or nanocrystalline and amorphous, phases. Such coatings offer a possibility of tailoring the coating microstructure and achieving new improved properties of coated materials. In this work a duplex surface treatment, consisting of an oxygen diffusion treatment and deposition of low friction nanocomposite nc-MeC/a-C (Me = transition metal, Ti, W or Cr) coatings, was applied for improvement of the Ti-6Al-4V alloy properties. The coatings composed of nanocrystallites of transition metal carbides (TiC or Cr{sub x}C{sub y} or WC) embedded in hydrogen-free amorphous carbon (a-C) matrix were deposited onto the surface of an oxygen hardened Ti-6Al-4 V alloy substrate by means of a simple DC magnetron sputtering. A nano/microstructure of the substrate material and coatings has been examined by scanning- and transmission electron microscopy complemented with the results of X-ray diffraction analyses. It was found that the nanocomposite coatings are composed of different carbide nanocrystals (with sizes of a few nanometres) embedded in an amorphous carbon matrix. The results of qualitative and quantitative analyses of the nanocrystalline phase in the coatings with use of high-resolution transmission electron microscopy combined with image analysis are given in the paper. An effect of the nano/microstructure parameters of the coated alloy onto its micro-mechanical (nanohardness and Young's modulus) and tribological properties (wear resistance and friction coefficient) is discussed in the paper.

36 MATERIALS SCIENCE↗

Delamination analysis of metal-ceramic multilayer coatings subject to nanoindentation

Internal damage has been experimentally observed in aluminum (Al)/silicon carbide (SiC) multilayer coatings subject to nanoindentation loading. Post-indentation characterization has identified that delamination at the coating/substrate interface is the most prominent form of damage. In this study the finite element method is employed to study the effect of delamination on indentation-derived hardness and Young's modulus. The model features alternating Al/SiC nanolayers above a silicon (Si) substrate, in consistence with the actual material system used in earlier experiments. Cohesive elements with a traction–separation relationship are used to facilitate delamination along the coating/substrate interface. Delamination is observed numerically to be sensitive to the critical normal and shear stresses that define the cohesive traction–separation behavior. Axial tensile stress below the edge of indentation contact is found to be the largest contributor to damage initiation and evolution. Delamination results in a decrease in both indentation-derived hardness and Young's modulus. As a result, a unique finding is that delamination can occur during the unloading process of indentation, depending on the loading condition and critical tractions.

36 MATERIALS SCIENCE↗

Leaf spring made of fiber-reinforced resin

A leaf spring made of a matrix reinforced by at least two types of reinforcing fibers with different Young's modulus is described in this Japanese patent. At least two layers of reinforcing fibers are formed by partially arranging the reinforcing fibers toward the direction of the thickness of the leaf spring. A mixture of different types of reinforced fibers is used at the area of boundary between the two layers of reinforced fibers. The ratio of blending of each type of reinforced fiber is frequently changed to eliminate the parts where discontinuous stress may be applied to the leaf spring. The objective of this invention is to prevent the rapid change in Young's modulus at the boundary area between each layer of reinforced fibers in the leaf spring.

Hori, J.↗

Technical Note: Multipurpose CT, ultrasound, and MRI breast phantom for use in radiotherapy and minimally invasive interventions

Purpose: To develop a multipurpose gel-based breast phantom consisting of a simulated tumor with realistic imaging properties in CT, ultrasound and MRI, or a postsurgical cavity on CT. Applications for the phantom include: deformable image registration (DIR) quality assurance (QA), autosegmentation validation, and localization testing and training for minimally invasive image-guided procedures such as those involving catheter or needle insertion. Methods: A thermoplastic mask of a typical breast patient lying supine was generated and then filled to make an array of phantoms. The background simulated breast tissue consisted of 32.4 g each of ballistic gelatin (BG) powder and Metamusil™ (MM) dissolved in 800 ml of water. Simulated tumors were added using the following recipe: 12 g of barium sulfate (1.4% v/v) plus 0.000 14 g copper sulfate plus 0.7 g of MM plus 7.2 g of BG all dissolved in 75 ml of water. The phantom was evaluated quantitatively in CT by comparing Hounsfield units (HUs) with actual breast tissue. For ultrasound and MRI, the phantoms were assessed based on subjective image quality and signal-difference to noise (SDNR) ratio, respectively. The stiffness of the phantom was evaluated based on ultrasound elastography measurements to yield an average Young’s modulus. In addition, subjective tactile assessment of phantom was performed under needle insertion. Results: The simulated breast tissue had a mean background value of 24 HU on CT imaging, which more closely resembles fibroglandular tissue (40 HU) as opposed to adipose (−100 HU). The tumor had a mean CT number of 45 HU, which yielded a qualitatively realistic image contrast relative to the background either as an intact tumor or postsurgical cavity. The tumor appeared qualitatively realistic on ultrasound images, exhibiting hypoechoic characteristics compared to background. On MRI, the tumor exhibited a SDNR of 3.7. The average Young’s modulus was computed to be 15.8 ± 0.7 kPa (1 SD). Conclusions: We have developed a process to efficiently and inexpensively produce multipurpose breast phantoms containing simulated tumors visible on CT, ultrasound, and MRI. The phantoms have been evaluated for image quality and elasticity and can serve as a medium for DIR QA, autosegmentation QA, and training for minimally invasive procedures.

60 APPLIED LIFE SCIENCES↗

Thermal and mechanical properties of palm oil-based polyurethane acrylate/clay nanocomposites prepared by in-situ intercalative method and electron beam radiation

Palm oil based-polyurethane acrylate (POBUA)/clay nanocomposites were prepared via in-situ intercalative polymerization using epoxidized palm oil acrylate (EPOLA) and 4,4' methylene diphenyl diisocyante (MDI). Organically modified Montmorillonite (ODA-MMT) was incorporated in EPOLA (1, 3 and 5%wt), and then subjected to polycondensation reaction with MDI. Nanocomposites solid films were obtained successfully by electron beam radiation induced free radical polymerization (curing). FTIR results reveal that the prepolymer was obtained successfully, with nanoclay dispersed in the matrix. The intercalation of the clay in the polymer matrix was investigated by XRD and the interlayer spacing of clay was found to be increased up to 37 Å, while the structure morphology of the nanocomposites was investigated by TEM and SEM. The nanocomposites were found to be a mixture of exfoliated and intercalated morphologies. The thermal stability of the nanocomposites was significantly increased by incorporation of nanoclay into the polymer matrix. DSC results reveal that the Tg was shifted to higher values, gradually with increasing the amount of filler in the nanocomposites. Tensile strength and Young's modulus of the nanocomposites showed remarkable improvement compared to the neat POBUA.

36 MATERIALS SCIENCE↗

Ab initio study of anisotropic mechanical properties of LiCoO{sub 2} during lithium intercalation and deintercalation process

The mechanical properties of Li{sub x}CoO{sub 2} under various Li concentrations and associated anisotropy have been systematically studied using the first principles method. During the lithium intercalation process, the Young's modulus, bulk modulus, shear modulus, and ultimate strength increase with increasing lithium concentration. Strong anisotropy of mechanical properties between a-axis and c-axis in Li{sub x}CoO{sub 2} is identified at low lithium concentrations, and the anisotropy decreases with increasing lithium concentration. The observed lithium concentration dependence and anisotropy are explained by analyzing the charge transfer using Bader charge analysis, bond order analysis, and bond strength by investigating partial density of states and charge density difference. With the decrease of Li concentration, the charge depletion in the bonding regions increases, indicating a weaker Co-O bond strength. Additionally, the Young's modulus, bulk modulus, shear modulus, and toughness are obtained by simulating ab initio tensile tests. From the simulated stress-strain curves, Li{sub x}CoO{sub 2} shows the highest toughness, which is in contraction with Pugh criterion prediction based on elastic properties only.

36 MATERIALS SCIENCE↗

A Fracture Mechanics Approach to Thermal Shock Investigation in Alumina-Based Refractory

The thermal shock behavior of large grain size, alumina-based refractories was investigated experimentally using a standard water quench test. A mathematical model was employed to simulate the thermal stability behavior. Behavior of the samples under repeated thermal shock was monitored using ultrasonic measurements of dynamic Young's modulus. Image analysis was used to observe the extent of surface degradation. Analysis of the obtained results for the behavior of large grain size samples under conditions of rapid temperature changes is given.

36 MATERIALS SCIENCE↗

Elastic properties of B-C-N films grown by N{sub 2}-reactive sputtering from boron carbide targets

Boron-carbon-nitrogen films were grown by RF reactive sputtering from a B{sub 4}C target and N{sub 2} as reactive gas. The films present phase segregation and are mechanically softer than boron carbide films (a factor of more than 2 in Young's modulus). This fact can turn out as an advantage in order to select buffer layers to better anchor boron carbide films on substrates eliminating thermally induced mechanical tensions.

36 MATERIALS SCIENCE↗

3D multi-scale modelling of mechanical behaviour of sound and leached mortar

A 3D multi-scale modelling of mechanical properties of cement-based materials approach is presented. The proposed approach provides a quantitative means to estimate and predict the mechanical properties of cement-based materials taking into account the eventual changes in the micro-structure. Two numerical tools are combined. First, the NIST's 3D model (CEMHYD3D) is used to generate a realistic 3D Representative Volume Element of cement-based materials at different scales. Then, multi-scale simulations are performed by using the FE software Abaqus for the calculation of the mechanical behaviour. The approach is then successfully applied to a specific mortar in order to determine firstly its mechanical behaviour under tensile and compression loadings and secondly the evolution of its Young's modulus under the leaching phenomenon. This evolution is a key parameter since the leaching may be critical for the mechanical integrity of concrete structures such as radioactive waste storage systems in which cement-based materials may be largely used. The numerical results of the modelling are consistent with the experimental ones.

36 MATERIALS SCIENCE↗

Mechanical and thermal properties of LaMgAl{sub 11}O{sub 19}

Lanthanum magnesium hexaaluminate (LaMgAl{sub 11}O{sub 19}) powders were synthesized successfully at 1300 {sup o}C for 4 h by solid-state reaction, and LaMgAl{sub 11}O{sub 19} ceramic was prepared at 1700 {sup o}C for 6 h by pressureless sintering. Phase composition, microstructure, mechanical and thermophysical properties of LaMgAl{sub 11}O{sub 19} ceramic were investigated. Results show that the flexural strength and fracture toughness of LaMgAl{sub 11}O{sub 19} ceramic are 353.3 {+-} 12.5 MPa and 4.60 {+-} 0.46 MPa m{sup 1/2}. Young's Modulus and Poisson ratio is 295 GPa and 0.23, respectively. The linear thermal expansion coefficient of LaMgAl{sub 11}O{sub 19} ceramic from 473 K to 1473 K is 9.17 x 10{sup -6}/K, and thermal conductivity at 1273 K is 2.55 W/m K.

36 MATERIALS SCIENCE↗

Effect of Ultrasonic Treatment on The Tensile and Impact Properties of Thermoplastic Natural Rubber Nanocomposites Reinforced with Carbon Nanotubes

This study investigates the effect of ultrasonic treatment on the mechanical properties of thermoplastic natural rubber (TPNR) nanocomposites reinforced with multi-walled nanotubes. The TPNR nanocomposites were prepared using melt blending method from polypropylene (PP), natural rubber (NR) and liquid natural rubber (LNR) as a compatibilizer, respectively, with 1% of Multi-wall nanotubes. The nanocomposite was prepared using the indirect technique (IDT) with the optimum processing parameters at 180 deg. C with 80 rpm mixing speed and 11 minutes processing time. The results have showed that the good dispersion on nanotubes was achieved by ultrasonic treatment. The optimization of ultrasonic time indicated that the maximum tensile and impact properties occurred with 1 h ultrasonic treatment. The Young's modulus, tensile strength, elongation at break and impact strength have increased by almost 11%, 21%, 43% and 50%, respectively. The results from our study indicate that nanotubes have as excellent reinforcement filler in TPNR matrix.

36 MATERIALS SCIENCE↗

Cross-type optical separation of elastic oblate capsules in a uniform flow

The dynamic behavior of an elastic capsule with an initially oblate spheroidal shape during cross-type optical separation was numerically investigated. The penalty immersed boundary method was adopted for the fluid-membrane interaction, and the optical force calculation was conducted by using the ray optics method including the ray-surface intersection algorithm. The oblate elastic capsule of b/a = 0.5 with different surface Young's moduli and different initial inclination angles was considered. The oblate capsule with higher surface Young's moduli was less deformed, and was more migrated for each initial inclination angle. Unlike the oblate rigid particle, the initially inclined capsules with moderate inclination angles were similarly migrated since the oblate elastic capsule was deformed during rotation near the laser beam axis. The oblate capsules can be separated according to the surface Young's modulus, except for nearly non-inclined capsules. As the fluid velocity decreased, the migration distance increased. The maximum deformation parameter was insensitive to the fluid velocity. Furthermore, a new dimensionless number (S{sub ec}) was introduced to predict the migration distance of the oblate elastic capsule.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Are Effective Properties Effective?

The effective moduli (effective Young's modulus, effective Poisson's ratio, effective shear modulus, and effective bulk modulus) of dispersed-phase-reinforced composite materials are determined at the mesoscopic level using three-dimensional parallel boundary element simulations. By comparing the mesoscopic BEM results and the macroscopic results based on effective properties, limitations in the effective property approach have been examined.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fatigue Characterization of Functionally Graded Metallic Alloys

Functionally graded components exhibit spatial variations of mechanical properties in contrast with, and as an alternative to, purely homogeneous components. A large class of graded materials, however, are in fact mostly homogeneous materials with property variations (chemical or mechanical) restricted to a specific area or layer produced by applying for example a coating or by introducing sub-surface residual stresses. However, it is also possible to obtain graded materials with a smooth transition of mechanical properties along the entire component, for example in a 40 mm component. This is possible, for example, by using centrifugal casting technique or incremental melting and solidification technique. In this paper we will study fully metallic functionally graded components with a smooth gradient, focusing on fatigue crack propagation. Fatigue propagation will be assessed in the direction parallel to the gradation (in different homogeneous layers of the functionally graded component) to assess what would be fatigue crack propagation on the direction perpendicular to the gradation. Fatigue crack growth rate (standard mode I fatigue crack growth) will be correlated to the mode I stress intensity factor range. Other mechanical properties of different layers of the component (Young's modulus) will also be considered in this analysis. The effect of residual stresses along the component gradation on crack propagation will also be taken into account. A qualitative analysis of the effects of some important features, present in functionally graded materials, will be made based on the obtained results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

First principle study of elastic and thermodynamic properties of ZrZn{sub 2} and HfZn{sub 2} under high pressure

A comprehensive investigation of the structural, elastic, and thermodynamic properties for Laves-phases ZrZn{sub 2} and HfZn{sub 2} are conducted using density functional total energy calculations combined with the quasi-harmonic Debye model. The optimized lattice parameters of ZrZn{sub 2} and HfZn{sub 2} compare well with available experimental values. We estimated the mechanical behaviors of both compounds under compression, including mechanical stability, Young's modulus, Poisson's ratio, ductility, and anisotropy. Additionally, the thermodynamic properties as a function of pressure and temperature are analyzed and found to be in good agreement with the corresponding experimental data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermal shock resistance of silicon oxynitride

The thermal shock resistance of Si2N2O refractory material was studied. The thermal expansion coeff. is 3.55x10 to the -6th power at 20 to 800 C and 2.86x10 to the -6th power m/m/deg at 20 to 200 C. The breaking loads are high at high stress. Young's modulus E and the shear modulus G decrease linearly with increasing porosity. For dense material E sub o approx. = 216,500 N/mm2 and G approx = 90,600 N/mm2. The Vickers hardness of the dense material is comparable to that of sapphire. The results on thermal shock show that R, the breaking load, stays constant for T T sub c, the first cracks appear and R decreases sharply for T=T sub c. As the severity of the thermal shock is increased at T T sub c, a small no. of new, large-size cracks appears. The shock's cumulative effect is negligible, and repeated shocks do not change the cracks. The low values of the thermal expansion coefficient and Young's modulus and the high tension breaking load are considered. Sintered Si2N2O with 5% MgO shows excellent cracking resistance under thermal shock.

Glandus, J. C.↗