SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A method of detecting a seizure includes collecting volatile organic compounds with a collector material of a collector; separating a mixture of the volatile organic compounds into its constituent chemicals with a gas chromatography column; ionizing the constituent chemicals to create ionized chemicals and detecting the ionized chemicals; and analyzing the ionized chemicals to identify seizure-indicative volatile organic compounds.
Direct supercritical CO 2 (sCO 2 ) power cycles require structural materials compatible with hot sCO 2 containing high levels of water and oxygen impurities. Chromia-forming Ni-based superalloys, which are leading candidates at temperatures > 600 °C, have shown good compatibility in pure sCO 2 , however potential impurity effects are not well understood. In this report we exposed several commercial Ni-based alloys to 95%CO 2 -4%H 2 O-(1-3)%O 2 at 750 °C and 0.1 or 20 MPa for 2500 h. Protective chromia scales formed in all cases. Nevertheless, water vapor-assisted oxide volatilization clearly occurred at high pressure. The volatilization rates decreased with time, but still represent a potentially serious compatibility issue in real, high-velocity, sCO 2 systems.
Here, in this study, we present new Ga isotope data from a suite of 28 mare basalts and lunar highland rocks. The δ 71 Ga values of these samples range from -0.10 to +0.66‰ (where δ 71 Ga is the relative difference between the 71 Ga/ 69 Ga ratio of a sample and the Ga-IPGP standard), which is an order of magnitude more heterogeneous than δ 71 Ga values in terrestrial magmatic rocks. The cause of this isotopic heterogeneity must be established to estimate the bulk δ 71 Ga value of the Moon. In general, low-Ti basalts and ferroan anorthosite suite (FAS) rocks have δ 71 Ga values that are lower than high-Ti basalts and KREEP-rich rocks. The observation that rocks derived from later forming LMO cumulates have higher δ 71 Ga values suggests that Ga isotopes are fractionated by processes that operate within the chemically evolving LMO, rather than localized degassing or volatile redistribution. Correlations between indices of plagioclase removal from the LMO (e.g. Eu/Eu*) with Ga isotope ratios suggest that a Δ 71 Ga plagioclase-melt of -0.3‰, (where Δ 71 Ga plagioclase-melt is the isotopic fractionation associated with crystallization of plagioclase from a melt), could drive the observed isotopic fractionation in high-Ti mare basalts and KREEP-rich rocks. This would be consistent with the observation that FAS rocks have δ 71 Ga values that are lower than mare basalts. However, the addition of KREEP-like material into the mare basalt source regions would not contribute enough Ga to perturb the isotopic composition outside of analytical uncertainty. Thus, basalts derived from early formed LMO cumulates such as those from Apollo 15, would preserve light Ga isotopic compositions despite containing modest amounts of urKREEP. We estimate that the δ 71 Ga value of the LMO was ~0.14‰ prior to the onset of plagioclase crystallization and extraction. Whether this δ 71 Ga value is representative of the initial BSM cannot be ascertained from the current dataset. It remains plausible that the Moon accreted with a heavier Ga isotopic composition than the Earth. Alternatively, the Moon and Earth could have accreted with similar isotopic compositions (BSE = 0.00 ± 0.06‰, Kato et al., 2017) and volatile loss drove the LMO to higher δ 71 Ga values prior to formation of the lunar crust.
Decarbonizing the transportation sector is likely to require both electrification and increased incorporation of biofuels and/or bioblendstocks. While the social and environmental benefits of bioblendstocks are well understood, their real value for the fuel producers has not been established. As such, this work considers prenol as a bioblendstock case study to identify sources of intrinsic value to fuel blenders by studying the properties of binary mixtures with gasoline components. The considered refinery blendstocks were samples of full range naphthas from the distillation, fluidized catalytic cracking, isomerization, alkylation, and reforming units. Octane numbers, Reid vapor pressure, distillation curves, and sulfur content were evaluated. Our results indicate the need for adjusting the formulation of the base fuel, depending on the interplay among the properties of the bioblendstock and those of the base fuel. Prenol increased research octane number (RON) and octane sensitivity (OS) of the base fuel, by up to 25 and 10 octane numbers, respectively. Additionally, 10 vol% prenol reduced RVP up to 2.2 psi, for the more volatile blendstock. Thus, considering prenol as a low volatility, RON/OS boosting bioblendstock, the composition of the preferred base fuel was proposed as containing reduced olefins and aromatics, and increase light fractions. The potential impact of this new gasoline formulation on refining processes and products gives rise to direct sources of value to the refiners, such as exporting products to the chemicals market, increasing the value of intermediate refinery streams, decreasing operating severity of certain refinery units, and broadening of the product suite.
Renewed interest in gallium isotope systematics has stemmed from the fact that Ga is moderately volatile and is hypothesized to undergo kinetic fractionation during evaporation. In this work, we present the first Ga isotope data from terrestrial volatile depleted samples including a suite of experimentally heated rhyolitic soils, fallout melt glass, and splash-form tektites from the Australasian strewn field (hereafter termed australite tektites). The Ga in these samples is isotopically heavy compared to Ga in terrestrial basalts and estimates for the composition of the bulk silicate Earth (BSE). For each sample suite the isotopic fractionation of Ga scales with the degree of Ga depletion, consistent with isotopic fractionation caused by evaporation.
The accumulation of carbon dioxide (CO 2 ) within enclosed spaces, along with volatile organic compounds, under certain humidity, temperature, and ventilation conditions is associated with detrimental human health symptoms such as fatigue. Color-based chemical sensing is a promising approach to detect CO 2 levels relevant to indoor air quality through producing fast, quantifiable output visible to the naked eye. In a prior work, a colorimetric gas sensor was fabricated through synthesizing the metal-organic framework, ZIF-8, as the adsorbent, followed by post-synthetic mixing with a dye, phenol red (PSP), and primary amine, ethylenediamine (ED). While this sensor (termed PSP-ED/ZIF-8) maintained its structural integrity in atmospheric conditions and exhibited an increasing fuchsia-to-yellow color change with increasing CO 2 levels in dry environment, the colorimetric response greatly suffered in the presence of humid CO 2 . Here in this work, a significantly improved colorimetric CO 2 sensor (referred to as ED/PSP:ZIF-8) is accomplished through directly incorporating phenol red in the ZIF-8 metal and linker precursor solutions and then blending with ethylenediamine. MATLAB-generated color distributions and in-situ ultraviolet-visible (UV-Vis) spectroscopic studies quantitatively demonstrate an enhanced colorimetric gas response of ED/PSP:ZIF-8 compared to that of PSP-ED/ZIF-8 across an important range of CO 2 for indoor air quality monitoring (500 – 3500 ppm) and across a range of humidity. The new sensor also exhibits high selectivity to CO 2 compared to select volatile organic compounds, such as acetone and ethanol, which contribute to human health symptoms experienced indoors. The enhanced performance is attributed to the proposed incorporation of phenol red within ZIF-8, while maintaining the chemical stability of the MOF.
Connected and Automated Vehicles (CAVs) can potentially improve the performance of the transportation system by reducing human errors. This paper investigates the safety impact of CAVs in a mixed traffic with conventional vehicles at intersections. Analyzing real-world AV crashes in California revealed that rear-end crashes at intersections are the dominant crash type. Therefore, to enhance our understanding of the future interactions between human-driven vehicles with CAVs at intersections, a simulation framework was developed to model the mixed traffic environment of Automated Vehicles (AV), cooperative AVs, and conventional human-driven vehicles. In order to model AVs driving behavior, Adaptive Cruise Control (ACC) and cooperative ACC (CACC) models are utilized. Particularly, this study explores system improvements due to automation and connectivity across varying CAV market penetration scenarios. ACC and CACC car following models are used to mimic the behavior of AVs and cooperative AVs. Real-world connected vehicle data are utilized to modify and tune the acceleration/deceleration regimes of the Wiedemann model. Next, the driving volatility concept capturing variability in vehicle speeds was utilized to calibrate the simulation to represent the safety performance of a real-world environment. Two surrogate safety measures are used to evaluate the safety performance of a representative intersection under different market penetration rate of CAVs: the number of longitudinal conflicts and driving volatility. At low levels of ACC market penetration, the safety improvements were found to be marginal, but safety improved substantially with more than 40% ACC penetration. Additional safety improvements can be achieved more quickly through the addition of cooperation and connectivity through CACC. Furthermore, ACC/CACC vehicles were found to improve mobility performance in terms of average speed and travel time at intersections.
In this paper, we consider the deployment of battery energy storage systems (BESSs) paired with photovoltaics (PV) to form a hybrid clean energy center (HCEC), where the BESS is equipped for two main purposes: i) reducing the volatility of PV output and ii) shifting energy to meet an export limit. We develop a linear dynamical model to characterize the output of an HCEC and express the volatility and export power as functions of the battery's dispatch operations. We also propose an optimal sizing method via second-order cone programming (SOCP) to maximize the net benefits of the HCEC. Numerical studies are performed to illustrate and validate the proposed method.
Henry’s law states that the abundance of a volatile solute dissolved in a liquid is proportional to its abundance in the gas phase. It applies at equilibrium and in the limit of infinite dilution of the solute. For historical reasons, numerous different definitions, names, and symbols are used in the literature to express the proportionality coefficient, denoted the “Henry’s law constant”. Furthermore, a consistent set of recommendations is presented. An important distinction is made between two new recommended reciprocal quantities: “Henry’s law solubility constant” (H s ) and “Henry’s law volatility constant” (H v ). Eight recommended variants of H s and H v are described and relations among them presented.
Coatings play key roles in solid oxide fuel cell (SOFC) stack durability. For example, diffusion barrier coatings on Cr-containing interconnect and balance of plant (BOP) components protect electrodes from Cr poisoning over the long operational lifetimes (>10,000 hours) of the fuel cell stack. Common defects in coatings, such as cracks, pinholes, and porosity, result in a failure to protect the electrodes, resulting in shorter operational lifetime and thus higher cost. It is very unlikely, even in the best coating process, that all these defects can be mitigated, hence identifying critical defects in parts, and removing defective parts from production before they can damage the stack, becomes paramount. Furthermore, these quality control techniques must be operational in the production/assembly line (in-line), i.e., high throughput and non-destructive, and cost effective. Redox Power Systems, LLC (Redox) together with the National Renewable Energy Laboratory (NREL) developed much needed high throughput, in-line metrology techniques for protective coatings. The overall goal of the project is to lower cost while increasing robustness, reliability, and endurance of SOFC stacks. To accomplish this, we had several objectives, including: to identify key coating and substrate defects that lead to coating failure through the use of detailed characterization methods (e.g., microscopy, XRD, EDS, electrochemistry); to assess capabilities of in-line metrology techniques, e.g., optical profilometry (Redox) and thermography (NREL), to probe these defects, or evidence thereof; demonstrate long-term performance of “defect-free” protective coatings, as identified by in-line metrology, in solid oxide fuel cell (SOFC) stack operation. In the first part of this project, the ability to identify key defects expected to lead to coating and SOFC degradation using in-line metrology tools were evaluated. Coated interconnect samples with controlled defect types and populations were tested under conditions similar to SOFC operation, followed by detailed post-test analysis to reveal the defects responsible for observed degradation. In the second part of the project, the optimal in-line metrology techniques and methodologies were used to map the defect distribution in full-size interconnects with critical defects intentionally allowed to exist in some cases. These interconnects underwent SOFC testing for extended periods (up to ~3,000 hours) followed by post-test analysis to evaluate the effectiveness of in-line metrology techniques in mitigating MCO coating related degradation. Key accomplishments in this project included the following: Demonstrated ASR of < 0.05 ohm-cm 2 at 650 °C for 1,000 hours with low defect (determined by in-line metrology) interconnect samples (average ASR=37 milliohms-cm 2 after over 1,000 hours). Demonstrated that low defect coatings on interconnects (as screened using in-line metrology) have low volatilization of chromium at ~650 °C for 1,000 hours as detected using Cr-getter material (< 5 at% increase above baseline); 1022 hour duration tests under humidified, elevated temperature (750 °C rather than 650 °C) compared a base case against different coating thicknesses. Demonstrated capability to identify initial key defects of interest with in-line metrology techniques using up to 8 cm by 10 cm having coatings with and without intentional defects of interest using thermal imaging and optical profilometry. Correlated key defects identified using metrology techniques with observed coating performance (e.g., ASR and Cr volatility). Conducted several 4 cm by 4 cm cell tests using MCO-interconnects that were pre-screened using some of the metrology techniques developed in the project (e.g., optical profilometry). An analysis of ASR measurements were able to show that defect-free coatings resulted in the anticipated performance in the cell tests.
This research investigates the reductive removal of technetium-99 ({sup 99}Tc) by zero valent iron (ZVI) from low activity waste (LAW) off-gas condensate simulant as a secondary treatment after recovery from vitrification planned at the Hanford Tank Waste Treatment and Immobilization Plant (WTP). Due to its high volatility, only a fraction of Tc{sup (VII)} will be incorporated into glass waste forms. Volatilized Tc will be captured by an off-gas treatment system with current plans to recycle off-gas condensate back to the vitrification facility. The scheme with off-gas recycling will increase Tc loading in the glass waste, but will also increase the concentrations of sulfate, halides, and other problematic constituents impeding overall LAW processing and increasing volume of the glass product. This study focuses on Tc{sup (VII)} removal by ZVI as a feasible pathway to minimize off-gas condensate recycling, which may result in a reduction in the volumes of LAW waste to be immobilized and subsequent cost savings. ZVI is an established treatment agent for redox-active contaminants such as trichloroethylene, nitrate, arsenic, chromium, phenol, and others. It is a commercially available and cost-effective material. Our previous experiments showed that ZVI is very efficient for the reductive removal of {sup 99}Tc. In this work we studied ZVI oxidation under aerobic conditions at pH 7 with 0.1 M Na{sub 2}SO{sub 4} solution (ionic strength, IS, 0.3 M) in the presence and absence of {sup 99}Tc. The concentration of {sup 99}Tc and the changes in pH, dissolved oxygen (DO), and oxidation-reduction potential (ORP) of the simulated solutions were monitored over 8 days. The formation of iron oxide phases was probed by X-ray diffraction (XRD). Obtained results suggest that ZVI contact time with {sup 99}Tc containing solutions for 6 hours resulted in nearly complete removal of {sup 99}Tc from the aqueous phase. XRD analysis showed that the oxidation of ZVI is rapid with formation of magnetite (Fe{sub 3}O{sub 4}) with minor percentage of goethite and maghemite. This work is a part of a larger set of studies investigating the feasibility of {sup 99}Tc reductive removal from the LAW off-gas condensate. (authors)
The most efficient and stable perovskite solar cells (PSCs) are made from complex mixture of precursors, which are practically always dissolved in combinations of the volatile (and toxic) N, N-Dimethylformamide (DMF), and the non-volatile (and green) dimethyl sulfoxide (DMSO) solvents. Typically, to then form a thin film, an extreme oversaturation of the perovskite precursor is initiated to trigger nucleation sites, e.g. by vacuum, an airstream or a so-called antisolvent. Unfortunately, most such oversaturation triggers do not expel the lingering (and highly coordinating) DMSO, which is highly coordinating, from the thin films; this detrimentally affects long-term stability. Here, for the first time, we introduce (the green) dimethyl sulfide (DMS) as a novel nucleation trigger for perovskite films combining, uniquely, high coordination and high vapor pressure. More precisely, DMS coordinates more strongly than all currently used solvents, hence replacing them, including DMSO, effectively during film formation. Crucially, DMS also has among the highest vapor pressures reported in literature, thus effectively leaving the thin film shortly after formation. This gives DMS a universal scope: DMS replaces other solvents by coordinating more strongly and removes itself once the film formation is finished. To demonstrate this novel coordination chemistry approach, we process MAPbI 3 PSCs, typically dissolved in hard-to-remove (and green) DMSO achieving 21.6% efficiency, among the highest reported efficiencies for this system. To confirm the universality of our strategy, we tested DMS for FAPbI 3 as another composition, which showed higher efficiency of 23.5% compared to 20.9% for fabricated device with CB. Finally, this work provides a universal strategy to control perovskite crystallization using coordination chemistry heralding the revival of perovskite compositions with pure DMSO, such as MAPbI 3 .
2D materials have been of considerable interest as new materials for device applications. Non-volatile resistive switching applications of MoS 2 and WS 2 have been previously demonstrated; however, these applications are dramatically limited by high temperatures and extended times needed for the large-area synthesis of 2D materials on crystalline substrates. The experimental results demonstrate a one-step sulfurization method to synthesize MoS 2 and WS 2 at 550 °C in 15 min on sapphire wafers. Furthermore, a large area transfer of the synthesized thin films to SiO 2 /Si substrates is achieved. Following this, MoS 2 and WS 2 memristors are fabricated that exhibit stable non-volatile switching and a satisfactory large on/off current ratio (10 3 –10 5 ) with good uniformity. Tuning the sulfurization parameters (temperature and metal precursor thickness) is found to be a straightforward and effective strategy to improve the performance of the memristors. Furthermore, the demonstration of large-scale MoS 2 and WS 2 memristors with a one-step low-temperature sulfurization method with simple strategy to tuning can lead to potential applications such as flexible memory and neuromorphic computing.
The ramp-reversal memory (RRM) effect in metal–insulator transition metal oxides (TMOs), a non-volatile resistance change induced by repeated temperature cycling, has attracted considerable interest in neuromorphic computing and non-volatile memory devices. Our previous defect motion model successfully explained RRM in vanadium dioxide (VO 2 ), capturing observed critical temperature shifts and memory accumulation throughout the sample. However, this approach lacked interactions between metallic and insulating domains. Here, we extend our model by combining a correlated Random Field Ising Model with defect diffusion-segregation, enabling accurate hysteresis modeling while predicting the relationship between RRM and domain interactions. Our simulations demonstrate that the maximum RRM occurs when the turnaround temperature approaches the inflection point. This peak in RRM vs. turnaround temperature is consistent with prior transport measurements, as well as our own optical measurements reported here. Significantly, we find that increasing nearest-neighbor interactions enhances the maximum memory effect, thus providing a clear mechanism for optimizing RRM performance. Since our model employs minimal assumptions, we predict that RRM should be a widespread phenomenon in materials exhibiting patterned phase coexistence of electronic domains. This work not only advances fundamental understanding of memory behavior in TMOs but also establishes a much-needed theoretical framework for optimizing device applications.
Electrocatalytic oxidation is an attractive process for valorizing the carbon and removal of nitrogen present in the aqueous waste streams at ambient conditions. Here, we evaluated the electrocatalytic oxidation as a function of applied potential over a commercial Pt electrode of aqueous waste stream generated via hydrothermal liquefaction. We validated the conversion of quantifiable carbon (e.g., carboxylic acids, alpha hydroxyacids, alcohols, ketones, amides) and unquantifiable carbon as well as nitrogen removal. The unquantifiable carbon was valorized to quantifiable short chain organic molecules (e.g., acetic). Model studies showed that carboxylic acids, alcohol and ketones converted following (non-) Kolbe chemistry. Amides and alpha hydroxyacids formed carboxylic acids that subsequently converted via (non-) Kolbe chemistry. Ammonia was oxidized into N2. The reaction rate varied for each molecule family with carboxylic acids and ammonia having the highest reaction rates. The main reaction products from the electrocatalytic oxidation at the anode were volatile, short chain hydrocarbons (i.e., olefins, paraffins) and CO generated via Kolbe chemistry, while H2 was generated at the cathode. The parallel denitrification, valorization of carbon, and H2 generation of the aqueous waste can replace and simplify the current unit operations used in a commercial hydrothermal liquefaction process. The high operation potential required to drive the electrocatalytic reaction is responsible for high operation costs; however, they can be either partially subsidized with sale of excess H2 at the current DOE goal of $2/kg H2. Thus, the present work shows how electrocatalytic oxidation can be used to valorize aqueous waste streams into volatile hydrocarbons and H2.
Radioiodine accumulates in aqueous solutions and off-gas streams during nuclear fuel reprocessing due to its solubility in aqueous solutions and volatility, respectively. Additionally, radioiodine is highly mobile in geological environments and iodine-129 has been found to be one of the largest long-term contributors to chronic dose to humans in scenarios of radionuclide migration from geological repositories. Most of the radioiodine can be captured during fuel reprocessing in off-gas streams using solid sorbents and scrubbing solutions. Once iodine is captured, it must be stored in a durable form for eventual disposal. Iodosodalite has been investigated as a waste form for radioiodine, however these synthesis processes typically result in mixed products and iodine volatilization during consolidation. Therefore, this paper proposes a novel approach to synthesizing iodosodalite utilizing a sol-gel method. This method was chosen to lower processing temperatures and improve product yield. Preliminary experiments conducted to determine the viability of this synthetic method are presented. Additionally, consolidation of sol-gel derived iodosodalite with a glass-binder was explored using three different methods: 1) incorporating the glass-binder during gel preparation using alkoxide precursors; 2) separately preparing the glass binder using a sol-gel method; and 3) separately preparing the glass-binder using a melt-quench technique. Glass-bonded iodosodalite was successfully synthesized using these novel sol-gel approaches.
A model describing oxidation kinetics considering simultaneous oxidation and volatilization of external oxide scales was integrated with a CALPHAD-based coupled thermodynamic and kinetic approach to predict the oxidation-induced lifetime of foils of alloys 625 and 120. Long-term exposures in flowing air +10% H 2 O at 700 and 800 °C under two flow velocities were used to validate the modeling results. The time to a critical Cr concentration of 10 wt% at the oxide/alloy interface, t 10 , was shown to correlate with the breakdown of the Cr 2 O 3 scale for the studied experimental conditions. Finally, the modeling approach was extended to consider time-dependent oxidation and volatilization rate constants to develop a more appropriate lifetime criterion for microturbine recuperator foils.
The isotopic dichotomy between non-carbonaceous (NC) and carbonaceous (CC) meteorites indicates that meteorite parent bodies derive from two genetically distinct reservoirs, which presumably were located inside (NC) and outside (CC) the orbit of Jupiter and remained isolated from each other for the first few million years of the solar system. Here we review the discovery of the NC–CC dichotomy and its implications for understanding the early history of the solar system, including the formation of Jupiter, the dynamics of terrestrial planet formation, and the origin and nature of Earth’s building blocks. The isotopic difference between the NC and CC reservoirs is probably inherited from the solar system’s parental molecular cloud and has been maintained through the rapid formation of Jupiter that prevented significant exchange of material from inside (NC) and outside (CC) its orbit. The growth and/or migration of Jupiter resulted in inward scattering of CC bodies, which accounts for the co-occurrence of NC and CC bodies in the present-day asteroid belt and the delivery of presumably volatile-rich CC bodies to the growing terrestrial planets. Earth’s primitive mantle, at least for siderophile elements like Mo, has a mixed NC–CC composition, indicating that Earth accreted CC bodies during the final stages of its growth, perhaps through the Moon-forming giant impactor. The late-stage accretion of CC bodies to Earth is sufficient to account for the entire budget of Earth’s water and highly volatile species.