Results for “Vibration” — Page 20

NASA NTRS1991

Vibration-dissociation coupling in nonequilibrium flows

The purpose of the study is to evaluate all important physical phenomena contributing to the vibration-dissociation problem by developing a numerical technique for the simulation of the vibrational relaxation and dissociation/recombination of N(2) in an isothermal box. A set of coupled master equations representing each vibrational level of N(2) is solved, and both V-V and V-T exchanges between molecules and atoms are included, along with the effects of dissociation and recombustion from/to each level. It is observed that the inverse range parameter has a strong impact on the vibrational exchange rates and relaxation. In a heating case, the lower vibrational levels relax through a series of equilibrium distributions, while in a cooling case, a population inversion is formed in the upper levels. Other cases of heating and cooling will be simulated, and together with this work, used to develop a matrix of nonequilibrium relaxation runs.

Landrum, D. Brian↗

NASA NTRS1991

Effect of the rotational-vibrational excitation on molecular diameters

The kinetic molecular diameters of rotationally and vibrationally excited diatomic molecules and molecular ions are derived as functions of the rotational and vibrational quantum numbers of the molecules. Typical molecular diameters are studied in two cases: in low-temperature gas, where the molecular diameter is independent of the degree of rotational-vibrational excitation of the molecules, and in high-temperature gas, where the molecular diameter depends on the degree of rotational-vibrational excitation of the molecules. The rotational-vibrational excitation of molecules is shown to have a meaningful effect on the collisional properties of gases. The effect is stronger in gases of weakly-bound molecules.

Kang, S. H.↗

NASA NTRS1990

Gear noise, vibration, and diagnostic studies at NASA Lewis Research Center

The NASA Lewis Research Center and the U.S. Army Aviation Systems Command are involved in a joint research program to advance the technology of rotorcraft transmissions. This program consists of analytical as well as experimental efforts to achieve the overall goals of reducing weight, noise, and vibration, while increasing life and reliability. Recent analytical activities are highlighted in the areas of gear noise, vibration, and diagnostics performed in-house and through NASA and U.S. Army sponsored grants and contracts. These activities include studies of gear tooth profiles to reduce transmission error and vibration as well as gear housing and rotordynamic modeling to reduce structural vibration and transmission and noise radiation, and basic research into current gear failure diagnostic methodologies. Results of these activities are presented along with an overview of near-term research plans in the gear noise, vibration, and diagnostics area.

Zakrajsek, J. J.↗

NASA NTRS1992

Coping With Vibrations In A Multiple-Payload Platform

Paper discusses methods of coping with vibrations in large platform supporting multiple scientific instruments. Solution requires coordination of three engineering approaches: suppressing vibrations, isolating vibrations, and compensating for vibrations. Has considerable value as introductory text on aiming instruments and minimizing effects of vibrations in large structures.

Sirlin, Samuel W.↗

NASA NTRS1991

The NASA/industry design analysis methods for vibrations (DAMVIBS) program: Accomplishments and contributions

A NASA Langley-sponsored rotorcraft structural dynamics program, known as Design Analysis Methods for VIBrationS (DAMVIBS), has been under development since 1984. The objective of this program was to establish the technology base needed by the industry to develop an advanced finite-element-based dynamics design analysis capability for vibrations. Under the program, teams from the four major helicopter manufacturers have formed finite-element models, conducted ground vibration tests, made test/analysis comparisons of both metal and composite airframes, performed 'difficult components' studies on airframes to identify components which need more complete finite-element representation for improved correlation, and evaluated industry codes for computing coupled rotor-airframe vibrations. Studies aimed at establishing the role that structural optimization can play in airframe vibrations design work have also been initiated. Five government/industry meetings were held in connection with these activities during the course of the program. Because the DAMVIBS Program is coming to an end, the fifth meeting included a brief assessment of the program and its benefits to the industry.

Kvaternik, Raymond G.↗

NASA NTRS1992

Free vibrations of delaminated beams

Free vibration of laminated composite beams is studied. The effect of interply delaminations on natural frequencies and mode shapes is evaluated both analytically and experimentally. A generalized vibrational principle is used to formulate the equation of motion and associated boundary conditions for the free vibration of a composite beam with a delamination of arbitrary size and location. The effect of coupling between longitudinal vibration and bending vibration is considered. This coupling effect is shown to significantly affect the calculated natural frequencies and mode shapes of the delaminated beam.

Shen, M.-H. H.↗

NASA NTRS1992

NASDA's activities on vibration isolation technology

The National Space Development Agency's (NASDA) activities in providing various vibration isolation technologies for the Space Station Mission are covered in viewgraph form. Technologies covered include an active vibration isolation system for extra sensitive missions in the low frequency range, a passive damping system consisting of a damping rack for the reduction of resonance amplification, and an isolator for vibration isolation from low frequencies. Information is given in viewgraph form on the active vibration isolation concept, voice coil type electromagnetic suspension, a profile of an active vibration isolation system, a three degree of freedom ground experiment, and acceleration feedback.

Source record↗

NASA NTRS1992

Optimum design of a gearbox for low vibration

A computer program was developed for designing a low vibration gearbox. The code is based on a finite element shell analysis, a modal analysis, and a structural optimization method. In the finite element analysis, a triangular shell element with 18 degrees-of-freedom is used. In the optimization method, the overall vibration energy of the gearbox is used as the objective function and is minimized at the exciting frequency by varying the finite element thickness. Modal analysis is used to derive the sensitivity of the vibration energy with respect to the design variable. The sensitivity is representative of both eigenvalues and eigenvectors. The optimum value is computed by the gradient projection method and a unidimensional search procedure under the constraint condition of constant weight. The computer code is applied to a design problem derived from an experimental gearbox in use at the NASA Lewis Research Center. The top plate and two side plates of the gearbox are redesigned and the contribution of each surface to the total vibration is determined. Results show that optimization of the top plate alone is effective in reducing total gearbox vibration.

Inoue, Katsumi↗

NASA NTRS1992

Modal simulation of gearbox vibration with experimental correlation

A newly developed global dynamic model was used to simulate the dynamics of a gear noise rig at NASA Lewis Research Center. Experimental results from the test rig were used to verify the analytical model. In this global dynamic model, the number of degrees of freedom of the system are reduced by transforming the system equations of motion into modal coordinates. The vibration of the individual gear-shaft system are coupled through the gear mesh forces. A three-dimensional, axial-lateral coupled, bearing model was used to couple the casing structural vibration to the gear-rotor dynamics. The coupled system of modal equations is solved to predict the resulting vibration at several locations on the test rig. Experimental vibration data was compared to the predictions of the global dynamic model. There is excellent agreement between the vibration results from analysis and experiment.

Choy, Fred K.↗

NASA NTRS1991

Directional solidification of Pb-Sn eutectic with vibration

Pb-Sn eutectic alloy was directionally solidified at 1.4 to 3.2 cm/h with forced convection induced by axial vibration of the growth ampoule with a frequency of 10 to 40 Hz and an amplitude of 0.5 to 1.0 mm. To determine the exact growth rate, an interface demarcation technique was applied. The lamellar spacing was increased 10 to 40 percent in ingots solidified with vibration, compared to those solidified without vibration. The number of grain boundaries was increased by vibration. The average intensity of convection in the melt under axial vibration of the ampoule was estimated by comparing the experimental results with a theoretical model.

Caram, Rubens↗

NASA NTRS1990

A study of coupled rotor-fuselage vibration with higher harmonic control using a symbolic computing facility

A fundamental study of vibration prediction and vibration reduction in helicopters using active controls was performed. The nonlinear equations of motion for a coupled rotor/flexible fuselage system have been derived using computer algebra on a special purpose symbolic computing facility. The details of the derivation using the MACSYMA program are described. The trim state and vibratory response of the helicopter are obtained in a single pass by applying the harmonic balance technique and simultaneously satisfying the trim and the vibratory response of the helicopter for all rotor and fuselage degrees of freedom. The influence of the fuselage flexibility on the vibratory response is studied. It is shown that the conventional single frequency higher harmonic control (HHC) capable of reducing either the hub loads or only the fuselage vibrations but not both simultaneously. It is demonstrated that for simultaneous reduction of hub shears and fuselage vibrations a new scheme called multiple higher harmonic control (MHHC) is required. The fundamental aspects of this scheme and its uniqueness are described in detail, providing new insight on vibration reduction in helicopters using HHC.

Papavassiliou, I.↗

NASA NTRS1992

Modal simulation of gearbox vibration with experimental correlation

A newly developed global dynamic model was used to simulate the dynamics of a gear noise rig at NASA Lewis Research Center. Experimental results from the test rig were used to verify the analytical model. In this global dynamic model, the number of degrees of freedom of the system are reduced by transforming the system equations of motion into modal coordinates. The vibration of the individual gear-shaft system are coupled through the gear mesh forces. A three-dimensional, axial-lateral coupled, bearing model was used to couple the casing structural vibration to the gear-rotor dynamics. The coupled system of modal equations is solved to predict the resulting vibration at several locations on the test rig. Experimental vibration data was compared to the predicitions of the global dynamic model. There is excellent agreement between the vibration results from analysis and experiment.

Choy, Fred K.↗

NASA NTRS1993

Evaluation of a vibration diagnostic system for the detection of spur gear pitting failures

A vibration diagnostic system was used to detect spur gear surface pitting fatigue in a closed-loop spur gear fatigue test rig. The diagnostic system, comprising a personal computer with an analog-to-digital conversion board, a diagnostic system unit, and software, uses time-synchronous averaging of the vibration signal to produce a vibration image of each tooth on any gear in a transmission. Several parameters were analyzed including gear pair stress wave and raw baseband vibration, kurtosis, peak ratios, and others. The system provides limits for the various parameters and gives a warning when the limits are exceeded. Several spur gear tests were conducted with this system and vibration data analyzed at 5-min. intervals. The results presented herein show that the system is fairly effective at detecting spur gear tooth surface fatigue pitting failures.

Townsend, Dennis P.↗

NASA NTRS1993

Vibration and noise analysis of a gear transmission system

This paper presents a comprehensive procedure to predict both the vibration and noise generated by a gear transmission system under normal operating conditions. The gearbox vibrations were obtained from both numerical simulation and experimental studies using a gear noise test rig. In addition, the noise generated by the gearbox vibrations was recorded during the experimental testing. A numerical method was used to develop linear relationships between the gearbox vibration and the generated noise. The hypercoherence function is introduced to correlate the nonlinear relationship between the fundamental noise frequency and its harmonics. A numerical procedure was developed using both the linear and nonlinear relationships generated from the experimental data to predict noise resulting from the gearbox vibrations. The application of this methodology is demonstrated by comparing the numerical and experimental results from the gear noise test rig.

Choy, F. K.↗

NASA NTRS1993

Raman scattering measurements of vibrational and rotational distributions in expanding nitrogen

Vibrational and rotational population distributions in expanding nitrogen in the supersonic nozzle of a reflected shock tunnel were investigated using spontaneous Raman scattering spectroscopy. The experimental data are compared with two multitemperature nonequilibrium calculations, one based on the Landau-Teller model for vibrational relaxation, the other on the solution of the vibrational master equations. Good agreement was found between both the Landau-Teller and the master equation solutions for the vibrational energy mode, but the experimentally inferred rotational temperatures were found to be systematically low, due to collisional narrowing. The dramatic increase in vibrational relaxation rates for a cooling flowfield reported in most previous studies was not reproduced by the present experiments.

Gillespie, Walter D.↗

NASA NTRS1991

The NASA/industry design analysis methods for vibrations (DAMVIBS) program - Accomplishments and contributions

A NASA Langley-sponsored rotorcraft structural dynamics program, known as Design Analysis Methods for VIBrationS (DAMVIBS), has been under development since 1984. The objective of this program was to establish the technology base needed by the industry to develop an advanced finite-element-based dynamics design analysis capability for vibrations. Under the program, teams from the four major helicopter manufacturers have formed finite-element models, conducted ground vibration tests, made test/analysis comparisons of both metal and composite airframes, performed 'difficult components' studies on airframes to identify components which need more complete finite-element representation for improved correlation, and evaluated industry codes for computing coupled rotor-airframe vibrations. Studies aimed at establishing the role that structural optimization can play in airframe vibrations design work have also been initiated. Five government/industry meetings were held in connection with these activities during the course of the program. Because the DAMVIBS Program is coming to an end, the fifth meeting included a brief assessment of the program and its benefits to the industry.

Kvaternik, Raymond G.↗

NASA NTRS1992

Two-mode elliptical-core weighted fiber sensors for vibration analysis

Two-mode, elliptical-core optical fibers are demonstrated in weighted, distributed and selective vibration-mode-filtering applications. We show how appropriate placement of optical fibers on a vibrating structure can lead to vibration mode filtering. Selective vibration-mode suppression on the order of 10 dB has been obtained using tapered two-mode, circular-core fibers with tapering functions that match the second derivatives of the modes of vibration to be enhanced. We also demonstrate the use of chirped, two-mode gratings in fibers as spatial modal sensors that are equivalents of shaped piezoelectric sensors.

Vengsarkar, Ashish M.↗

NASA NTRS1993

Vibration and noise analysis of a gear transmission system

This paper presents a comprehensive procedure to predict both the vibration and noise generated by a gear transmission system under normal operating conditions. The gearbox vibrations were obtained from both numerical simulation and experimental studies using a gear noise test rig. In addition, the noise generated by the gearbox vibrations was recorded during the experimental testing. A numerical method was used to develop linear relationships between the gearbox vibration and the generated noise. The hypercoherence function is introduced to correlate the nonlinear relationship between the fundamental noise frequency and its harmonics. A numerical procedure was developed using both the linear and nonlinear relationships generated from the experimental data to predict noise resulting from the gearbox vibrations. The application of this methodology is demonstrated by comparing the numerical and experimental results from the gear noise test rig.

Choy, F. K.↗