Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Surface Power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

NUMERICAL CALCULATION OF LOSSES OF TRAPPED VORTICES UNDER STRONG RF MEISSNER CURRENT AND DC SUPERHEATING FIELD IN TYPE II SUPERCONDUCTORS

Research on the vortex dynamics and enhancing of superheating field in superconductors has attracted much attention in accelerator physics community to develop next-generation high-performance accelerator cavities. However, the extreme dynamics of curvilinear elastic vortices driven by very strong currents close to the depairing limit or superheating field of a superconductor with a nanostructured surface has not been well understood. We calculated the superheating field Hsh and critical momentum kc characterizing the wavelength of the instability ?m of the Meissner state to flux penetration by solving numerically the Ginzburg?Landau equations. A bulk superconductor, superconductor with the inhomogeneous surface disorder (S-S), and multilayered surface (S-I-S) have been thoroughly investigated in this work. Our result showed that S-S and S-I-S structures can enhance the superheating field well above their clean limit. In this work extensive numerical simulation of the power dissipated by an oscillating vortex segment driven by the surface ac Meissner currents was performed. Our simulations take into account the nonlinear vortex line tension, vortex mass, Bardeen?Stephen viscous vortex drag applicable at low fields, and nonlinear Larkin-Ovchinnikov (LO) viscous drag coefficient ?(v) at high fields and pinning force. We showed that the LO decrease of ?(v) with the vortex velocity v could radically change the field dependence of the surface resistance Ri(H) caused by trapped vortices. At low frequencies Ri(H) exhibits a conventional increase with H. However, as frequency increases, the surface resistance becomes a nonmonotonic function of H which decreases with H at higher fields irrespective of the pinning distribution. Overheating can mask the descending field dependence of Ri(H) as frequency increases. Our numerical simulations also show that the LO effect can cause a vortex bending instability at high field amplitudes and frequencies, giving rise to the formation of dynamic kinks along with the vortex when a vortex is pinned strongly to one end. Nonlinear losses of trapped vortices in thick films under high-amplitude RF fields as functions of frequency, mean free path and pinning characteristics have been calculated.

Pathirana, Walive↗
DOE OSTI2022

Effect of Semiconducting Layer on Cable Insulation Damage Detection Using Surface Wave Reflectometry

This paper presents a study of the effect of the semiconducting layer present in medium and high voltage cables on surface wave propagation and its feasibility in detecting insulation damage on cables. Simulation studies were conducted using Ansys High Frequency Structure Simulator (HFSS). It was observed that attenuation increased with thicker semiconducting layer and higher conductivity of the layer. For instance, on a 24.4 mm diameter power cable, the electric field strength associated with a 1 GHz surface wave declines with distance and fades away after 30 m when a 2 mm thick semiconducting layer is present. More results as a function of semiconducting layer thickness, material conductivity and permittivity, distance of a damaged section, etc. will be presented.

reflectometry, unshielded power cable, semiconduct↗
DOE OSTI2024

Power over fiber development for HEP detectors

Power-over-Fiber (PoF) technology has been used extensively in settings where high voltages require isolation from ground and electromagnetic isolation is critical. In cryogenic environments, PoF offers a reliable power transmission technology, leveraging optical fibers to transfer power with minimal system degradation. PoF technology excels in maintaining low noise levels and isolation when delivering power to sensitive electronic systems operating in extreme temperature ranges and high voltage environments. Here, in a novel application of PoF for a HEP detector, power is provided to photon detector modules located on a surface at ~300 kV with respect to ground in the planned DUNE experiment. This summary paper of the PoF talk at the 16th PISA Meeting on Advanced Detectors highlights the R&D effort of PoF in extreme conditions and underscores its capacity to revolutionize power delivery and management in critical applications offering a dependable solution with low noise, optimal efficiency, and superior isolation. The DUNE (Abi et al., 2020) experiment will soon deploy large liquid argon (LAr) time projection chambers (TPC) to detect neutrino interactions and other particle physics phenomena. In addition to the particle tracking provided by the TPC, photon detectors, powered by a first ever PoF system, in the cryostat will leverage the high scintillation light yield of LAr to provide crucial timing and additional calorimetric information.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Two-dimensional simulations of internal gravity waves in the radiation zones of intermediate-mass stars

Intermediate-mass main-sequence stars have large radiative envelopes overlying convective cores. This configuration allows internal gravity waves (IGWs) generated at the convective–radiative interface to propagate towards the stellar surface. The signatures of these waves can be observed in the photometric and spectroscopic data from stars. Here, we have studied the propagation of these IGWs using two-dimensional (2D) fully non-linear hydrodynamical simulations with realistic stellar reference states from the 1D stellar evolution code, Modules for Stellar Astrophysics (MESA). When a single wave is forced, we observe wave self-interaction. When two waves are forced, we observe non-linear interaction (i.e. triadic interaction) between these waves forming waves at different wavelengths and frequencies. When a spectrum of waves similar to that found in numerical simulations is forced, we find that the surface IGW frequency slope is consistent with recent observations. This power law is similar to that predicted by linear theory for the wave propagation, with small deviations that can be an effect of non-linearities. When the same generation spectrum is applied to 3 M ⊙ models at different stellar rotation and ages, the surface IGW spectrum slope is very similar to the generation spectrum slope.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

High Flux Helium Irradiation of Dispersion-Strengthened Tungsten Alloys and Effects of Heavy Metal Impurity Layer Deposition

Tungsten has been chosen as the plasma-facing material (PFM) for the divertor region in ITER and also a candidate PFM for future plasma-burning nuclear fusion reactors. During fusion device operation, PFMs will be exposed to low-energy He irradiation at high temperatures, resulting in sub-surface bubbles and surface morphology changes such as pores and fuzz. Carbide dispersion-strengthened W materials may enhance the ductility of W, but their behavior under high flux He irradiation remains unclear. In this work, the response of dispersion-strengthened tungsten materials to high flux, low energy He irradiation at high temperature is examined. Tungsten alloyed with 1, 5, or 10 wt. % tantalum carbide or titanium carbide exposed to these conditions result in surface pores, coral-like feature growth and sub-surface helium bubbles. Reactor-relevant helium irradiation (5 x 10 26 m -2 fluence) combined with high powered laser pulses to simulate off-normal reactor events does not significantly alter the surface morphology, as the surface nanostructures appear stable and cracks are only observed on a localized region of one sample. However, specimens show the development of an impurity layer on the surface, likely impurity deposition from the sample holder during irradiation, resulting in a mixed material layer on the surface. Helium bubbles exist in this impurity layer, and obscure conclusions about helium interactions with the carbide dispersoids. Nonetheless, it is clear that the dispersoid microstructure limits He bubble formation and subsequent surface nanostructuring, attributed to the dispersoid composition.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Python-EPICS RF Conditioning Automatic Control System at the Spallation Neutron Source

The RF Test Facility (RFTF) at the Spallation Neutron Source (SNS) is used for the conditioning of RF compo-nents such as ceramic vacuum windows and power cou-plers prior to their installation in the H- ion linear accel-erator. This process exposes components to high-power RF fields and thermal cycling to improve performance and remove surface impurities. To automate and optimize this process, a Python-based EPICS control system was developed alongside targeted hardware upgrades. The system enables real-time monitoring and control of RF power levels, temperature, and vacuum pressure. A user-friendly graphical interface was implemented using CS-Studio (Phoebus), allowing operators to adjust parameters and collect data efficiently. The system integrates a High-Power Protection Module (HPM) for interlocks based on vacuum and arc detection, ensuring safe operation. These upgrades have significantly improved the efficiency, accuracy, and safety of RF conditioning at the SNS RFTF. This paper describes the updated RF conditioning sys-tem, highlighting the software and hardware develop-ments and their application in support of the Proton Pow-er Upgrade (PPU) project.

Lee, Sung-Woo [ORNL] (ORCID:000000030915835X)↗
DOE OSTI2022

Evaluating the Effects of Nitrogen Doping and Oxygen Doping on SRF Cavity Performance

Superconducting radiofrequency (SRF) cavities are resonators with extremely low surface resistance that enable accelerating cavities to have extremely high quality factors (Q₀). High Q₀ decreases the capital required to keep the accelerators cold by reducing power loss. The performance of SRF cavities is largely governed by the surface composition of the first §I{100}{nm} of the cavity surface. Impurities such as oxygen and nitrogen have been observed to yield high Q₀, but their precise roles are still being studied. Here, we compare the performance of cavities doped with nitrogen and oxygen in terms of surface composition and heating behavior with field. A simulation of the diffusion of oxygen into the bulk of the cavity was built using COMSOL Multiphysics software. Simulated results were compared to the actual surface composition of the cavities as determined from secondary ion mass spectrometry analysis. Understanding how these impurities affects performance allows us to have further insight into the underlying mechanisms that enable these surface treatments to yield high Q₀.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Unconventional Photocurrents from Surface Fermi Arcs in Topological Chiral Semimetals

The nonlinear optical responses from topological semimetals are crucial in both understanding the fundamental properties of quantum materials and designing next-generation light sensors or solar cells. However, previous work focused on the optical effects from bulk states only, disregarding the responses from topological surface states. Here, we propose a new surface-only photocurrent response from chiral Fermi arcs. Using the ideal topological chiral semimetal RhSi as a representative, we quantitatively compute the photogalvanic currents from Fermi arcs on different surfaces. By rigorous crystal symmetry analysis, we demonstrate that Fermi arc photogalvanic currents can be perpendicular to the bulk injection currents regardless of the choice of materials surface. We then generalize this finding to other cubic chiral space groups and predict material candidates. Our theory reveals a powerful notion where common crystalline symmetry can be used to completely disentangle bulk and surface optical responses in many conducting material families.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

High gradient off-axis coupled C-band Cu and CuAg accelerating structures

Here, we report the high gradient testing results of two single-cell off-axis coupled standing wave accelerating structures. Two brazed standing wave off-axis coupled structures with the same geometry were tested: one made of pure copper (Cu) and one made of a copper–silver (CuAg) alloy with a silver concentration of 0.08%. A peak surface electric field of 450 MV/m was achieved in the CuAg structure for a klystron input power of 14.5 MW and a 1 μs pulse length, which was 25% higher than the peak surface electric field achieved in the Cu structure. The superb high gradient performance was achieved because of the two major optimizations in the cavity's geometry: (1) the shunt impedance of the cavity was maximized for a peak surface electric field to accelerating gradient ratio of ~2 for a fully relativistic particle, and (2) the peak magnetic field enhancement due to the input coupler was minimized to limit pulse heating. These tests allow us to conclude that C-band accelerating structures can operate at peak fields similar to those at higher frequencies while providing a larger beam iris for improved beam transport.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Innovative laser-based methods for monitoring fuel retention in ITER

This paper addresses the challenge of tritium inventory management in ITER and future fusion reactors, highlighting the importance of accurate tritium measurement and its spatial distribution within the vacuum vessel. Given ITER’s operational constraints, especially the limit on tritium retention, precise measurement is essential for both safety and regulatory compliance. To tackle these questions, the paper presents the T-monitor diagnostic system developed by Forschungszentrum Jülich, which uses Laser-Induced Desorption (LID) in combination with Diagnostic Residual Gas Analysis (DRGA) to measure hydrogen isotope concentrations on the surface of divertor tiles. The system integrates a high-power laser, advanced optical components, and a Fast Scanning Mirror Unit (FSMU) for accurate laser spot positioning with rapid response. Designed to measure in situ tritium retention, the diagnostic provides high-resolution spatial mapping, vital for evaluating detritiation strategies. The laser heating process increases the divertor surface temperature to 1600 K within the laser spot, promoting hydrogen isotope desorption. Accurate measurements require the precise control of laser parameters, including pulse duration and spot size, with a target relative accuracy of 20%. The optical design includes both in-vessel and ex-vessel components, such as durable high-reflectivity mirrors made of gold and copper, selected not only for their infrared performance but also for their transmission of visible wavelengths for observation purposes. To protect optical components from contamination, a pneumatic shutter is used.

Hydrogen isotopes↗
DOE OSTI2020

Terahertz quantum-cascade patch-antenna VECSEL with low power dissipation

We report a terahertz quantum-cascade vertical-external-cavity surface-emitting laser (QC-VECSEL) based upon a metasurface consisting of an array of gain-loaded resonant patch antennas. Compared with the typical ridge-based metasurfaces previously used for QC-VECSELs, the patch antenna surface can be designed with a much sparser fill factor of gain material, which allows for reduced heat dissipation and improved thermal performance. Here, it also exhibits larger amplification thanks to enhanced interaction between the incident radiation and the QC-gain material. We demonstrate devices that produce several milliwatts of continuous-wave power in a single mode at ~4.6 THz and dissipate less than 1 W of pump power. Use of different output couplers demonstrates the ability to optimize device performance for either high power or high operating temperature. Maximum demonstrated power is 6.7 mW at 4 K (0.67% wall-plug efficiency, WPE) and 0.8 mW at 77 K (0.06% WPE). Directive output beams are measured throughout with divergence angles of ~5°.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Highly Integrated Wide Bandgap Power Module for Next Generation Plug-In Vehicles (Final Report)

Wide bandgap devices are key enablers for high power density traction inverters. A highly integrated wide bandgap (WBG) power module enables higher temperature operation, higher inverter efficiency and overall smaller die area with the same power delivery. However, it requires careful design of the power module to take advantage of all the superior material properties that silicon carbide (SiC) provides over conventional silicon (Si) Insulated Gate Bipolar Transistor (IGBT) based design. This project developed an efficient and densely packed SiC power module for an automotive traction inverter application. Extensive study was performed to select the best performing SiC die considering a wide range of temperature variation, suitability to integrate into target packaging, robust body diode performance and overall high electrical efficiency. Multiple design ideas were explored to achieve lower stray inductance for both power loop and signal loop, uniform current distribution, compact form factor, and very high thermal performance. The final power module package includes all six inverter switches in the same module (six-pack) with die sintered at both bottom and top surfaces utilizing high performance substrate to achieve high electrical and thermal performance. Two power module variants were developed using 900 V and 1200 V devices for operating at two different high voltage levels (> 600 V HV battery). Both power modules were comprehensively characterized, and high efficiency operation of the inverter was confirmed through analysis. Finally, a complete functional inverter was built with the 1200V power modules using other essential components (HV capacitors, gate driver board, controller board, current sensor, connectors etc.) and tested using GM’s standard test procedure. There are several challenges associated with adopting WBG devices for high voltage operation. In order to assess and mitigate those challenges, GM and subrecipients of this project have conducted multiple detailed studies. This includes phase current reconstruction using integrated Rogowski coil, device junction temperature estimation using on-state gate resistance, modeling and testing the effect of high voltage and fast switching on motor insulation and bearings, partial discharge inception voltage measurement under different environmental conditions. Findings of all these studies are summarized in this report.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Hydrodynamic characterization of the coastal pioneer array ocean observing system

Ocean observation buoys require relatively small amounts of power, yet traditionally necessitate costly resupply trips for battery replacement. With the offshore location of the buoys and small power requirements, wave energy may be an effective solution for providing consistent and reliable power to support the buoy instrumentation. The US National Science Foundation Ocean Observatories Initiative (OOI) includes arrays of point absorber-like buoy systems used for ocean observation that have been deployed at multiple locations including the Southern Mid-Atlantic Bight. A study is currently underway to design a pitch resonator wave energy converter to supplement existing renewable energy generation for powering observation instrumentation. This paper details field measurements from surface moorings of the OOI Coastal Pioneer Array, which informs the subsequent development of a numerical model for the moored observation system. The model is developed in Wave Energy Converter Simulator (WEC-Sim), which leverages the Simscape multibody solver within the MATLAB/Simulink framework and linear potential flow theory to simulate the hydrodynamic interactions and multibody dynamics in 6 degrees of freedom. Multiple tuning variables are considered to produce a model for the system that matches well with empirical data (about 8% error). In conclusion, the WEC-Sim model will serve as a platform for integrating the pitch resonator wave energy converter concept and deployment preparation (detailed design including power take-off and control systems, response evaluation, etc.).

hydrodynamic modeling↗
DOE OSTI2025

Wind and Weather Variability within the Californian Offshore Wind Energy Areas

Weather variability over the Northeast Pacific (NEP) region and its influence on wind resources within the Californian offshore wind energy areas (WEAs) at Humboldt and Morro Bay are characterized using 20-years reanalysis model and satellite data. The hub-height (180 m) winds at both locations are predominantly northwesterly driven by the NEP high pressure system, with strong coastal gradients in surface pressure, fluxes, planetary boundary layer (PBL) depths and cloudiness. These sharp coastal gradients and strong annual cycles of temperature and moisture advections pose potential challenges in accurately modeling the local wind resource. Hub-height wind speeds and power capacity factors significantly vary for different regimes of PBL depths, surface fluxes and rain area fractions. This highlights the importance of studying the physical mechanisms driving these weather regimes, hence our analysis of how large-scale NEP weather variability drives the local meteorology at the WEAs. Furthermore, at both WEAs, PBL tops and cloud boundaries intersect the rotor layer (80-280 m) more than 30% and 20% of the time, respectively. While PBL depths significantly modulates hub-height winds and power, cloud boundaries do not have a similar impact, likely due to reanalysis errors in simulating cloud boundaries accurately. These findings underscore the challenges in deploying tall wind turbines in shallow cloudy boundary layers, where the interaction between clouds, precipitation, and atmospheric layers can impact turbine efficiency. As turbines grow taller and are deployed in more complex meteorological conditions, understanding these interactions is crucial for improving wind power forecasting and optimizing energy production in coastal regions.

17 WIND ENERGY↗
DOE OSTI2020

Design and demonstration of a distributed-coupling linear accelerator structure

We present a topology for linear accelerators (linacs) in which the power is distributed to the cavities through a waveguide with periodic apertures that guarantees the correct phases and amplitudes along the structure length. Unlike conventional traveling and standing-wave linacs, the presented topology allows the cavity shapes to be designed without the constraints applied to the coupling between cells to transfer power from one cell to the next. Therefore, the topology permits more degrees of freedom for the optimization of individual cavity shapes in comparison with conventional linacs. The cavity shapes can be optimized for power consumption and efficiency, and/or the manipulation of the surface fields for high gradient operation. This topology also provides a possibility for low-temperature manufacturing techniques that prevent the annealing of the material during typical brazing processes; hence, the material could retain its original properties such as hardness. We present a design and an experimental demonstration of this linac.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Tidal Currents in San Juan Archipelago, Washington

Re-analyzed acoustic Doppler current profiler (ADCP) data originally collected by NOAA CO-OPS (Center for Operational Oceanographic Products and Services) and equivalent point data from Pacific Northwest National Laboratory's FVCOM (Finite Volume Community Ocean Model) model of the region. Data are processed to products describing characteristics of tidal currents relevant to tidal turbines, as well as power output estimates for a notional turbine deployed from a surface platform or from the seabed at each location. These data underpin the results presented in their associated paper - see below.

16 TIDAL AND WAVE POWER↗
DOE OSTI2025

Braxton Marlatt Intern Poster

The Internet of Things (IoT) encompasses a vast network of interconnected devices embedded with software, sensors, and network connectivity, enabling data collection and exchange. While IoT technology revolutionizes various industries, it also introduces significant security challenges. This research focuses on enhancing IoT security through the implementation of Zero Trust Architecture concepts, specifically targeting the Network and Device pillars of the Cybersecurity and Infrastructure Security Agency’s Zero Trust Maturity Model. By generating Codified Attack Surfaces (CAS) using custom Structured Threat Information eXpression bundles, this project aims to provide enhanced visibility into network communications, detect vulnerabilities in device firmware, and improve the overall security posture for IoT devices and networks. The methodology involves defining custom STIX schema and objects, collecting data from intra-IoT traffic, external network traffic, and firmware analysis, and automating the conversion and correlation of this data into STIX bundles. The automated generation of attack surfaces offers comprehensive insights into activity, vulnerabilities, and anomalies within an IoT environment, enabling proactive threat identification and mitigation.

24 - POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Chemical and Chemical-Mechanical Polishing of Surface Roughness on L-PBF/GRCop-42 Cu-Cr-Nb Additive Manufactured 10-GHz RF Structures

Laser-based powder bed fusion (L-PBF) allows additive manufacture (AM) of lower hybrid current drive (LHCD) radio-frequency (RF) launchers from Glenn Research Copper, a Cr 2 Nb precipitation-hardened alloy (GRCop-42) in configurations unachievable with conventional machining. Rough surfaces in AM components increase RF losses and lead to arcing in high-power vacuum RF applications. Chemical polishing, chemical-mechanical polishing, or a combination of both were utilized to planarize the internal surfaces of RF structures, resulting in surface roughness as low as R a = 0.2 µm. Refinement in polishing techniques now enables GRCop-42 alloys (4 at. % Cr, 2 at. % Nb) to achieve similar surface roughness to GRCop-84 (8 at. % Cr, 4 at. % Nb) and equivalent cavity losses to extruded oxygen-free copper waveguides at 10 GHz.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗