Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Effect of laser rescanning on the grain microstructure of a selective laser melted Al-Mg-Zr alloy

Highlights: • Laser rescanning of a new Al-Mg-Zr alloy was investigated. • SLM of the Al-Mg-Zr alloy results in a duplex grain structure. • Rescanning of the alloy results in a refinement of the microstructure. - Abstract: The microstructures of alloys created via Additive Manufacturing (AM) can vary substantially from those present in cast or wrought products, due to the very rapid solidification associated with AM. While numerous studies have investigated the process-microstructure relationship of alloys created by Selective Laser Melting (SLM), few have investigated the effects of laser rescanning to alter the microstructure or take advantage of the rapid solidification conditions the process provides. This study investigates the effect of single- or multiple pass laser scanning upon the grain structure of Addalloy™, a new Al-Mg-Zr alloy strengthened via L1{sub 2} Al{sub 3}Zr precipitates. The bottom of the melt pools consisted of fine equiaxed grains (1.3 μm) that nucleated from primary Al{sub 3}Zr (100–400 nm) precipitates. The top of the melt pool consists of columnar grains (up to 40 μm long), consistent with lack of Al{sub 3}Zr nucleants due to Zr solute trapping from increased solidification velocities. Additional laser scanning (a second or third scan) reduces the amounts of columnar grains and increased the number equiaxed grains. The change is attributed to a shallower melt pool remelting the columnar grain region upon rescanning, due to reduced laser energy absorption and increased heat losses in the solid.

36 MATERIALS SCIENCE↗

Directional solidification in immiscible systems - The influence of gravity

The possibility of producing aligned fibrous composite microstructures with a high volume fraction of the immiscible phase, L2, through the directional solidification of hypermonotectic alloys is examined. Early work suggests that low gravity conditions are necessary to prevent sedimentation of the more dense L2 phase. However, if convective flows result, they disrupt the formation of the desired fibrous microstructure and produce a disperse structure. The need for long-duration low-g experiments is emphasized.

Andrews, J. B.↗

Formation and Toughening Mechanisms of Dispersions in Interfacial Intermetallics of Dissimilar Laser Al/Steel Joints

The key to improve the strength of Al/steel dissimilar joint is to toughen the hard and brittle interfacial intermetallics. Introducing soft and tough dispersions into the interfacial intermetallics would be a promising method. In the present study, Zn-Al alloy (Zn-22Al) was used as the filler metal to generate dispersions in the interfacial intermetallics matrix of dissimilar laser Al/steel joint. The results have shown that soft and tough dispersions, i.e., FeZn{sub 10,} Al-rich amorphous phase, and Zn solid solution, were successfully introduced into the hard and brittle Fe{sub 2}Al{sub 5−x}Zn{sub x} matrix. The formation of these dispersions was resulted from diffusion of elements Fe and Al and infiltration of liquid Zn along the grain boundaries of Fe{sub 2}Al{sub 5−x}Zn{sub x} matrix and the subsequent chemical reaction and solidification. With this kind of interfacial microstructure, the joint exhibited a stable peak fracture load of 1200 N even though the interfacial layer thickness increased from 20 to 45 μm. This was because the interfacial layer was toughened by the soft and tough dispersions. Using this example, introduction of soft and tough dispersions into hard and brittle intermetallics matrix to toughen interfacial layer and then strengthening of dissimilar joints will be highlighted.

36 MATERIALS SCIENCE↗

Solidification of Calcium Ferrite Melt Using Ultrasonic Vibration: Effect and Mechanism

Calcium ferrite (CF) is a very important binder phase in iron ore sintering processes. To improve the microstructure of CF, power ultrasound was introduced during its solidification process, and the effect of immersion depth of ultrasonic probe (IDUP) on the properties of CF was investigated in detail. The results indicated that the microstructure of CF was greatly refined; the grain size decreased from 2864 μm without ultrasonic vibration to 841 μm with ultrasonic vibration at an immersion depth of 30 mm. Without ultrasonic vibration, the density and compressive strength of CF slag were 3904 kg/m{sup 3} and 38.3 MPa, respectively. When the IDUP was increased from 10 to 30 mm, the density and compressive strength of CF increased from 4049 to 4452 kg/m{sup 3} and 52.5 to 87.3 MPa, respectively. Further, the reducibility of CF was examined. The reduction time, at the same reduction rate, decreased from 347 minutes without ultrasonic vibration to 200 minutes with ultrasonic vibration at an IDUP of 30 mm. The rate-limiting step was obviously improved, which may be attributable to the grain refinement of CF and composition segregation in the slag. In general, the properties of CF were greatly improved due to the cavitation and acoustic streaming of ultrasonic waves.

36 MATERIALS SCIENCE↗

Effects of Undercooling and Cooling Rate on Peritectic Phase Crystallization Within Ni-Zr Alloy Melt

The liquid Ni-16.75 at. pct Zr peritectic alloy was substantially undercooled and containerlessly solidified by an electromagnetic levitator and a drop tube. The dependence of the peritectic solidification mode on undercooling was established based on the results of the solidified microstructures, crystal growth velocity, as well as X-ray diffraction patterns. Below a critical undercooling of 124 K, the primary Ni{sub 7}Zr{sub 2} phase preferentially nucleates and grows from the undercooled liquid, which is followed by a peritectic reaction of Ni{sub 7}Zr{sub 2}+L → Ni{sub 5}Zr. The corresponding microstructure is composed of the Ni{sub 7}Zr{sub 2} dendrites, peritectic Ni{sub 5}Zr phase, and inter-dendritic eutectic. Nevertheless, once the liquid undercooling exceeds the critical undercooling, the peritectic Ni{sub 5}Zr phase directly precipitates from this undercooled liquid. However, a negligible amount of residual Ni{sub 7}Zr{sub 2} phase still appears in the microstructure, indicating that nucleation and growth of the Ni{sub 7}Zr{sub 2} phase are not completely suppressed. The micromechanical property of the peritectic Ni{sub 5}Zr phase in terms of the Vickers microhardness is enhanced, which is ascribed to the transition of the peritectic solidification mode. To suppress the formation of the primary phase completely, this alloy was also containerlessly solidified in free fall experiments. Typical peritectic solidified microstructure forms in large droplets, while only the peritectic Ni{sub 5}Zr phase appears in smaller droplets, which gives an indication that the peritectic Ni{sub 5}Zr phase directly precipitates from the undercooled liquid by completely suppressing the growth of the primary Ni{sub 7}Zr{sub 2} phase and the peritectic reaction due to the combined effects of the large undercooling and high cooling rate.

36 MATERIALS SCIENCE↗

Phase-field simulation of microstructure formation in technical castings - A self-consistent homoenthalpic approach to the micro-macro problem

Performing microstructure simulation of technical casting processes suffers from the strong interdependency between latent heat release due to local microstructure formation and heat diffusion on the macroscopic scale: local microstructure formation depends on the macroscopic heat fluxes and, in turn, the macroscopic temperature solution depends on the latent heat release, and therefore on the microstructure formation, in all parts of the casting. A self-consistent homoenthalpic approximation to this micro-macro problem is proposed, based on the assumption of a common enthalpy-temperature relation for the whole casting which is used for the description of latent heat production on the macroscale. This enthalpy-temperature relation is iteratively obtained by phase-field simulations on the microscale, thus taking into account the specific morphological impact on the latent heat production. This new approach is discussed and compared to other approximations for the coupling of the macroscopic heat flux to complex microstructure models. Simulations are performed for the binary alloy Al-3at%Cu, using a multiphase-field solidification model which is coupled to a thermodynamic database. Microstructure formation is simulated for several positions in a simple model plate casting, using a one-dimensional macroscopic temperature solver which can be directly coupled to the microscopic phase-field simulation tool.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Computer-assisted Rheo-forging Processing of A356 Aluminum Alloys

Die casting process has been used widely for complex automotive products such as the knuckle, arm and etc. Generally, a part fabricated by casting has limited strength due to manufacturing defects by origin such as the dendrite structure and segregation. As an attempt to offer a solution to these problems, forging has been used as an alternative process. However, the forging process provides limited formability for complex shape products. Rheo-forging of metal offers not only superior mechanical strength but also requires significantly lower machine loads than solid forming processes. In order to produce semi-solid materials of the desired microstructure, a stirring process is applied during solidification of A356 aluminum molten state. This paper presents the results of an A356 aluminum alloy sample, which were obtained by experiment and by simulation using DEFORM 3D V6.1. Samples of metal parts were subsequently fabricated by using hydraulic press machinery. In order to compare the influence of loading method, two types of samples were fabricated: (1) samples fabricated under direct loading die sets (2) those fabricated under indirect loading die sets. The formability and defects, which were predicted by FEM simulation, were similar to those of samples used in practice.

36 MATERIALS SCIENCE↗

The influence of gravity level during directional solidification of immiscible alloys

During directional solidification of immiscible (hypermonotectic) alloys it is theoretically possible to establish a stable macroscopically-planar solidification front, and thus avoid sedimentation. Unfortunately, convective instabilities often occur which interfere with the directional solidification process. In this paper, stability conditions are discussed and results presented from directional solidification studies carried out aboard NASA's KC-135 zero-g aircraft. Samples were directionally solidified while the effective gravity level was varied from approximately 0.01 g for 25 s to 1.8 g for 45 s. Dramatic variations in microstructure were observed with gravity level during solidification.

Andrews, J. B.↗

Directional solidification of flake and spheroidal graphite cast iron in low and normal gravity environment

A NASA KC-135 research aircraft, flying repeated low-g trajectories that yield 20-30 sec of 0.1-0.001 g microgravity, has been used to study microgravity solidification's elimination of sedimentation and convection (with formation of unique and advantageous microstructures) for the case of eutectic-composition cast irons. The solidification interface of hypereutectic flake and spheroidal graphite cast irons has been slowly advanced through a 4 mm-diameter rod sample. Sample solidification rates have been correlated with accelerometer data, while independently controlling thermal gradients and solidification rates.

Hendrix, J. C.↗

Improving the Mechanical Properties of Cast Aluminum Via Ultrasonication-Induced Microstructural Refinement

One barrier to the broader use of cast aluminum alloys in automotive applications is their poor mechanical properties, especially compared to wrought materials. This study investigates the use of ultrasound to refine the microstructure of cast aluminum alloys during solidification and thus improve their mechanical properties. An A356 aluminum alloy (Al-Si-Mg) with added Fe (to mimic a recycle-grade alloy) was cast in a graphite mold with the simultaneous application of ultrasound. Tensile specimens were extracted from the castings and heat treated to a T6 temper. Ultrasonication during casting transformed the morphology of primary aluminum grains from dendritic (~140 microns in size) to globular (~36 microns in size), increased the ultimate tensile strength by 10 %, and tripled the ductility compared to casting without ultrasound. This improvement in strength and ductility demonstrates the potential for ultrasonic processing to improve the performance of cast aluminum alloys without altering their chemistry or additional post-processing.

Aluminum, Solidification, Ultrasound, Grain refinm↗

Effect of Eutectic Characteristics on Hot Tearing of Cast Superalloys

The occurrence of hot cracks in the blades of Ni-based superalloy turbocharger wheels is thought to be closely related to eutectic characteristics. Different alloys that are susceptible to hot tearing, namely K418, K419 and K424, were studied. SEM was used to obtain the microstructure of the alloys. DSC, isothermal solidification quenching process and EPMA were conducted to determine the relationship between the eutectic characteristics and solidification process, segregation behavior and dendrite coalescence. The results show that a large volume fraction of γ/γ′ eutectic indicates a wide-temperature solidification range and severe segregation. A large γ/γ′ eutectic size is a result of element segregation and poor dendrite coalescence. Ti is thought to promote the formation of a large isolated residual liquid pool and lead to a large eutectic size, leading to the poor coalescence behavior of the dendrites. The volume fraction and size of the γ/γ′ eutectic were considered, and a eutectic influence factor (E) was defined to evaluate the effect of eutectic characteristics on hot tearing in cast superalloys. It was found that a high E corresponds to high hot-tearing susceptibility.

36 MATERIALS SCIENCE↗

Microstructure and thermoelectric properties of CoSb 2.75 Ge 0.25-x Te x prepared by rapid solidification

Since the vibration modes of the pnicogen rings in CoSb3-based skutterudites fall within the range of frequencies of heat-carrying phonons, disruption of the rings by doping should have a strong influence on heat transport in this material. To test the premise, single-phase double-doped CoSb 2.75 Ge 0.25-x Te x x (x = 0.125–0.20) compounds were synthesized by combining melt spinning with a spark plasma sintering method. Following the melt-spinning process, the side of the ribbons contacting the copper drum is featureless and reflects its amorphous nature while the free surface of the ribbons is composed of 30–80 nm grains. After spark plasma processing the average grain size of the bulk samples is about 200 nm. High-resolution transmission electron microscopy images show an in situ nanostructure consisting of circular, 15 nm diameter dots of Te- and Ge-enriched skutterudite phase embedded in the skutterudite matrix. Transport properties were measured from 2 to 800 K as a function of Te and Ge content on the pnicogen (Sb) rings and the results were correlated with the structural data. Double-doping on pnicogen rings with Ge and Te, and using melt-spinning processing, results in binary skutterudite compounds that possess an impressive figure of merit of ZT ~ 1.1 at 750 K.

36 MATERIALS SCIENCE↗

Effect of Ultrasonic Treatment on the Microstructure of A201 Aluminium Alloy for Thixoforming

It is known that the introduction of high intensity ultrasonic waves into liquid and solidifying metals leads to a non-dendritic and fine grain structure which is the requirement for semi-solid feedstock production. The effect of vibration time on the semi-solid microstructure of the A201 aluminium alloy billets fabricated with the ultrasonic treatment in the liquid state was studied in this paper. It was observed that the application of ultrasound technology can break up and distribute the dendrites which are present in the as-cast alloy. A suitable thixotropic microstructure with relatively rounded and fine globules could be obtained by ultrasonically treating liquid metal at 690 deg. C for a treatment time of 1 minute, cooling to room temperature and then reheating to the semi-solid state. This shows the ultrasonic treatment could be an economic and alternative route to produce A201 semi-solid feedstock for thixoforming.

36 MATERIALS SCIENCE↗

Solidification structures on carbon materials surface-melted by repetitive laser pulses

The solidification morphology of carbon materials surface-melted by laser radiation at atmospheric pressure is studied. Electron microscopy results indicate that melt solidification is accompanied by the formation of surface microstructures, presumably due to the Rayleigh-Taylor instability in the molten carbon. The instability increment and surface tension coefficient of molten carbon are estimated, and the penetration of carbon vapour into the melt during one laser pulse is examined using numerical simulation. (interaction of laser radiation with matter. laser plasma)

36 MATERIALS SCIENCE↗

Ultrahigh strength and plasticity in laser rapid solidified Al–Si nanoscale eutectics

As-cast Al–20wt.% Si alloys were processed via laser rapid solidification (LRS) techniques to create eutectic microstructures with nanoscale interconnected, nanotwinned Si fibers. LRS morphologies exhibit higher flow stress, exceeding 800 MPa and uniform plastic deformation above 20% compared to as-cast alloy that fractures at strains below 8% at flow strength of approximately 200 MPa. The strengthening mechanisms of LRS morphologies are interpreted in terms of the interfacial constraints: increase in yield strength as well as strain hardening rate due to nanoscale confined slip in fibrous Al–Si eutectic, and load transfer and eventual plasticity in the nanoscale Si fibers.

36 MATERIALS SCIENCE↗

Alloy and structural optimization of a directionally solidified lamellar eutectic alloy

Mechanical property characterization tests of a directionally solidified Ni-20 percent Cb-2.5 percent Al-6 percent Cr cellular eutectic turbine blade alloy demonstrated excellent long time creep stability and indicated intermediate temperature transverse tensile ductility and shear strength to be somewhat low for turbine blade applications. Alloy and structural optimization significantly improves these off-axis properties with no loss of longitudinal creep strength or stability. The optimized alloy-structure combination is a carbon modified Ni-20.1 percent Cb-2.5 percent Al-6.0 percent Cr-0.06 percent C composition processed under conditions producing plane front solidification and a fully-lamellar microstructure. With current processing technology, this alloy exhibits a creep-rupture advantage of 39 C over the best available nickel base superalloy, directionally solidified MAR M200+ Hf. While improved by about 20 percent, shear strength of the optimized alloy remains well below typical superalloy values.

Sheffler, K. D.↗

Rapid solidification research at the NASA Lewis Research Center

This paper describes the research program initiated at the NASA Lewis Research Center for the study of rapid solidification of high temperature materials, with the major purpose for the development of advanced high-temperature and heat-flux materials for aircraft and aerosphace applications. Particular attention is given to the development of three alloys: Ni-aluminides, Nb-alloys, and Cu-alloys. Rapid solidification processing yielded alloys with novel microstructures, very fine grain sizes, reduced chemical segregation, and metastable extended solid solutions.

Locci, Ivan E.↗

Controlled Temperature Gradient Improves Freezing Alloy

Controlled gradient of temperature in advancing zone of solidification increases fatigue life of directionally solidified nickel-base superalloy. Improved solidification process eliminates, reduces, or controls microstructure of deleterious brittle phases, including carbides and gamma/gamma prime eutectic. Also reduces microsegregation and makes discrete carbides (if present) become fine and blocky. Expected to improve properties of other alloys, of both directionally-solidified polycrystalline and single-crystal forms.

Schmidt, Deborah↗