Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Shear Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Effects of Cooling Rates on Self-Reinforced Polyethylene Composites via Multiscale Experimental Characterizations

This study investigates cooling rate effects on self-reinforced polyethylene composites (PE-SRCs), focusing on macroscopic thermal and mechanical properties, and micro- to sub-micron morphologies. Unlike conventional fiber-reinforced composites (e.g., carbon and glass fiber based), cooling rate effects on SRCs remain less studied. PE-SRCs were fabricated from ultrahigh molecular weight polyethylene (UHMWPE) fabric and high-density polyethylene (HDPE) matrix with cooling rates from 0.76°C/min to 425°C/min. Tensile properties, including modulus (~9.5 GPa), strength (~360 MPa), and ultimate elongation (~6%), showed no significant cooling rate dependence. However, thermal analysis revealed melting temperature of HDPE matrix decreased from ~130°C to ~126.5°C with total crystallinity reducing from 84% to 75%. Wide-angle X-ray scattering confirmed decreasing crystallinity but at lower values (67%–59%), as thermal analysis might overestimate crystallinity. Small-angle X-ray scattering showed long period decreased from 24.3 to 17.4 nm, attributed to thinner lamellae and closer packing, suggesting limited crystal growth and faster nucleation. While cooling rates alter melting point and crystalline structures of HDPE matrix, these changes do not translate to substantial impact on macroscale mechanical properties of PE-SRCs. This insensitivity might be related to low interfacial shear strength at PE/PE interfaces, enabling process optimization while maintaining mechanical performance.

Cooling rate↗
NASA NTRS1985

Explosive Welding of Aluminum, Titanium and Zirconium to Copper Sheet Metal

The main material properties affecting the explosive weldability of a certain metal combination are the yield strength, the ductility, the density and the sonic velocity of the two metals. Successful welding of the metal combination depends mainly on the correct choice of the explosive welding parameters; i.e., the stand off distance, the weight of the explosive charge relative to the weight of the flyer plate and the detonation velocity of the explosive. Based on the measured and the handbook values of the properties of interest, the explosive welding parameters were calculated and the arrangements for the explosive welding of the Al alloy 6061-T6, titanium and zirconium to OFHC copper were determined. The relatively small sheet metal thickness (1/8") and the fact that the thickness of the explosive layer must exceed a certain minimum value were considered during the determination of the explosive welding conditions. The results of the metallographic investigations and the measurements of the shear strength at the interface demonstrate the usefulness of these calculations to minimize the number of experimental trials.

Hegazy, A. A.↗
DOE OSTI2023

Enhancing Composite Toughness Through Hierarchical Interphase Formation

High strength and ductility are highly desired in fiber-reinforced composites, yet achieving both simultaneously remains elusive. A hierarchical architecture is developed utilizing high aspect ratio chemically transformable thermoplastic nanofibers that form covalent bonding with the matrix to toughen the fiber-matrix interphase. The nanoscale fibers are electrospun on the micrometer-scale reinforcing carbon fiber, creating a physically intertwined, randomly oriented scaffold. Unlike conventional covalent bonding of matrix molecules with reinforcing fibers, here, the nanofiber scaffold is utilized - interacting non-covalently with core fiber but bridging covalently with polymer matrix - to create a high volume fraction of immobilized matrix or interphase around core reinforcing elements. This mechanism enables efficient fiber-matrix stress transfer and enhances composite toughness. Molecular dynamics simulation reveals enhancement of the fiber-matrix adhesion facilitated by nanofiber-aided hierarchical bonding with the matrix. The elastic modulus contours of interphase regions obtained from atomic force microscopy clearly indicate the formation of stiffer interphase. These nanoengineered composites exhibit a ≈60% and ≈100% improved in-plane shear strength and toughness, respectively. This approach opens a new avenue for manufacturing toughened high-performance composites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Phase Field Modeling of Corrosion for Design of Next-Generation Magnesium-Aluminum Vehicle Joints

In this study, WPI and its partners sought to understand galvanic corrosion in Mg-Al friction stir weld (FSW) joints. Unlike fusion welds, FSW is done in the solid state. This limits (but does not eliminate) the formation of brittle Al-Mg intermetallics, resulting in better joint strength and corrosion resistance. This study aimed to understand corrosion behavior of Mg-Al FSW joints by using a Cahn-Hilliard phase field electrochemistry model based on the work of Pongsaksawad et al. Its context challenge problem was an ultra-light door designed by Magna with 6061-Al sheet outer and ZEK100-Mg sheet inner panels, joined by an adhesive and FSW. Unlike most FSW joints, which weld through the softer material into the harder one, the Al sheet’s hem joint around Mg required the FSW tool to through the harder Al into the softer Mg, which was itself a challenge. Despite this challenge, PNNL succeeded in consistently making very strong FSW lap joints, by using a triflute tool and power control. Characterization showed mostly separate Al and Mg regions in the weld, usually with a hook protruding from Al into Mg, which likely contributed to high joint strength. Nanohardness mapping showed higher hardness in thin Mg swirls into the Al nugget, likely due to the intermetallics. The study used the industry standard SAE J2334 Cyclic Corrosion Test (CCT) to simulate corrosion conditions over the life of a vehicle, as well as linear polarization testing and ASTM G71 pitting corrosion testing. Corrosion reactions were: H 2 O + ½O 2 + 2e - → 2OH - at the Al cathode, and either Mg → Mg 2+ + 2e - or Mg + 2OH - → Mg(OH) 2 + 2e - at the Mg anode, with electron transfer through the joint. Mass loss increased with Al section length, supporting the hypothesis that galvanic corrosion in Al-Mg joints is limited by the cathodic reaction. Both pitting corrosion (first anode reaction) and hydroxide film formation (second reaction) were observed. The J2334 CCT test method was slightly modified, adding a chromium solution cleaning step after each week of corrosion testing, in order to remove Mg oxides and hydroxides and accurately measure mass loss over time. That said, FSW joints treated in this way did not did not exhibit significant reduction in lap shear strength of the joints vs. newly welded samples which had not undergone corrosion. Corrosion appeared to consist mainly of pitting in Mg in a way which did not directly affect the bond between the materials where the joints failed. A Cahn-Hilliard phase field model coupled with electrical potential described the electronically mediated galvanic corrosion electrochemical reactions described above in the four-component Al-Mg-H 2 O-(H 2 O+½O 2 ) system. This 2-D model successfully predicted Mg(OH)₂ formation at the anode in some circumstances, and Mg pitting corrosion in others, and showed the correct electric field directions in both cases. The model predicted Mg pit corrosion depth within a factor of two of measured pits.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS2020

AERoBOND Project Summary

Under NASA’s Convergent Aeronautics Solutions (CAS) project, the Adhesive-Free Bonding of Complex Composites (AERoBOND) project investigated off-stoichiometric epoxy polymers for fast, reliable assembly of epoxy matrix composite structures. The project goal was to demonstrate feasibility of the AERoBOND joining method by demonstrating mechanical properties greater than 80% of conventional co-cured materials while reducing structure weight by 1%. The project consisted of three convergent research areas: material and process development, systems analysis, and material and process modeling. Material and process development was the largest component of AERoBOND with approximately 6 FTE and 1WYE of support to formulate and characterize new resins, prepare carbon fiber prepregs, fabricate laminates, measure mechanical properties, analyze failure results, and select material and process improvements. The systems analysis activity estimated the potential reduction in part count and aircraft weight by comparing models of composite wing boxes with no fasteners (co-cured structure), fasteners in major joints (co-cured stringers), and fasteners in all joints. The materials and process modeling activity included a molecular model of the AERoBOND materials system to predict mechanical properties of resins with offset stoichiometry and a process model to predict the effect of resin formulation and processing conditions on the extent of mixing and degree of cure in a finished joint. As the number of airline passenger trips doubles in the next 20 years (IATA/Tourism Economics Air Passenger Forecasts, April 2019), the increased demand for new commercial aircraft is now the single greatest technical challenge to the airframe manufacturing industry. To meet efficiency requirements, new aircraft must be fabricated primarily from high performance structural composites, but manufacturing processes are inherently slow with the largest bottleneck attributed to assembly and installation of fasteners (NASA/TM–2019-220428). Manufactures of commercial transport aircraft are compelled to install more than 100,000 redundant fasteners into bonded joints to prevent failures due to unpredictable weak bonds. In structural adhesive bonds, the interface between adherend and adhesive is nearly two-dimensional making it susceptible to minute quantities of contamination, which can cause weak bonds. Currently, bond strength assessment is only possible through destructive testing (i.e., breaking the joint). For these reasons, regulatory organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded, primary-structures to alleviate concerns with bond performance. The AERoBOND process enables reflow of matrix resin during assembly to eliminate the material discontinuity at the interface, thereby eliminating the dependence of mechanical performance on interfacial adhesion. The AERoBOND joint is equivalent to the interlaminar region obtained during a co-cure process, so joint performance depends on the cohesive properties of the matrix resin. Conventional co-cured structures, although too costly and complex for large-scale manufacturing, are trusted by manufacturers and regulators, and are certified for flight with few or no redundant fasteners.Systems analysis performed on a composite wing model at the scale of a single-aisle commercial transport aircraft indicated that >20,000 redundant fasteners per wing could be eliminated by implementing the AERoBOND joining method. A total weight reduction of 15% was predicted in a wing box by eliminating fasteners and thinning components that must no longer support localized fastener loads and accommodate fastener dimensions. Interlaminar shear fracture toughness measured by the end-notched flexure test was greater than 1 kJ/m2 (nearly 140% of the co-cured benchmark property), which is greatly in excess of the project goals for mechanical properties. Testing was planned to measure interlaminar tensile fracture toughness as well as interlaminar tensile and shear strengths using the same AERoBOND configuration, but was delayed due to closure of LaRC facilities during the COVID-19 pandemic. The AERoBOND process model is partially validated and available for experimental use. It allows the user to input AERoBOND process parameters such as material composition, laminate configuration, and cure cycle to predict the final cure state of the AERoBOND joint. A preliminary, multi-scale material model was developed to predict AERoBOND joint mechanical properties (stiffness and strength) based on the cure state of the joint provided by the process model. The timing for transition of this technology within NASA is excellent as NASA initiates new enduring projects to address composites manufacturing rate challenges. AERoBOND technology is well suited to AAVP/AATT objectives for rapid manufacturing of a composite wing. A minimal effort (1 FTE/$15k procurement/0 WYE) is proposed in FY21 to continue a minor mechanical testing effort and maintain a SAA with ASX composites to develop commercial quality prepreg material. An RFI with the composites industry is suggested to quantify the technology gap between the current TRL and the TRL needed for transition to industry. A moderate effort [3-4 FTE/$150k/1 WYE (~$115k)] is proposed in FY22 for the “high rate composites manufacturing” project currently in planning. The partnership with ASX Composites will be expanded to produce material for sub-element/element-scale “panel-off” activities. Industry partnerships with airframe manufacturers is an expected component to explore damage tolerance and environmental stability. Further development of multi-scale modeling tools (process model, meso-scale model, and molecular model) is planned to enhance and deliver tools for rapid manufacturing infusion.

Frank Louis Palmieri↗
DOE OSTI2022

Multifunctional fiber-reinforced composites for passive sensing and energy harvesting with enhanced mechanical performance

Fiber-reinforced polymer composites (FRPCs) are valid alternatives to metals, especially in the aerospace industry, for their superior strength-to-weight ratio. FRPCs are generally manufactured by stacking layers of fibers and infusing them with epoxy-based adhesives to result in laminates. Such layer-by-layer structure often ensues a poor interlaminar property of the composites. Additionally, FRPCs can sustain complex damage modes because of their inherent anisotropic characteristics. For example, delamination can occur due to low-velocity impact at a subsurface level, which can result in premature catastrophic failures if undetected. Thus, structural monitoring is crucial to identify such damage. Point-based sensors (e.g., strain gauges, accelerometers, among many) can be embedded in the FRPCs for structural monitoring. However, their electrical power demand often embroils their usage. Therefore, the main objective of this research is to design and implement multifunctional composites that can simultaneously perform passive sensing and energy harvesting while exhibiting better mechanical performance. Previous research efforts have demonstrated that a continuous feed-through deposition of functional materials on fiber surfaces simultaneously enhanced the mechanical and sensing properties of the FRPCs. This study explores a similar approach to encode passive sensing and energy harvesting properties in the FRPCs by integrating ferroelectric microparticles on the fiber surfaces. Upon ensuring their superior interlaminar shear strength, sensing and energy harvesting properties were characterized through experimental studies. The outcome is a multifunctional composite fabricated by coating the fibers with functional microparticles through a high throughput, scalable, and low-cost approach that enables passive sensing, energy harvesting, and improved mechanical performance.

Gupta, Sumit↗
NASA NTRS2004

Improved BN Coatings on SiC Fibers in SiC Matrices

Modifications of BN-based coatings that are used as interfacial layers between the fibers and matrices of SiCfiber/SiC-matrix composite materials have been investigated to improve the thermomechanical properties of these materials. Such interfacial coating layers, which are also known as interphases (not to be confused with interphase in the biological sense), contribute to strength and fracture toughness of a fiber/matrix composite material by providing for limited amounts of fiber/matrix debonding and sliding to absorb some of the energy that would otherwise contribute to the propagation of cracks. Heretofore, the debonding and sliding have been of a type called inside debonding because they have taken place predominantly on the inside surfaces of the BN layers that is, at the interfaces between the SiC fibers and the interphases. The modifications cause the debonding and sliding to include more of a type, called outside debonding, that takes place at the outside surfaces of the BN layers that is, at the interfaces between the interphases and the matrix (see figure). One of the expected advantages of outside debonding is that unlike in inside debonding, the interphases would remain on the crack-bridging fibers. The interphases thus remaining should afford additional protection against oxidation at high temperature and should delay undesired fiber/fiber fusion and embrittlement of the composite material. A secondary benefit of outside debonding is that the interphase/matrix interfaces could be made more compliant than are the fiber/interphase interfaces, which necessarily incorporate the roughness of the SiC fibers. By properly engineering BN interphase layers to favor outside debonding, it should be possible, not only to delay embrittlement at intermediate temperatures, but also to reduce the effective interfacial shear strength and increase the failure strain and toughness of the composite material. Two techniques have been proposed and partially experimentally verified as candidate means to promote outside debonding in state-of-the-art SiC/SiC composites.

Morscher, Gregory N.↗
NASA NTRS2001

Microstructure, Mechanical Properties, Hot-Die Forming, and Joining of 47XD Gamma TiAl Rolled Sheets

The microstructure and mechanical properties, along with the hot-die forming and joining of Ti-47Al-2Nb-2Mn-0.8 vol% TiB, sheets (known as 47XD), produced by a low-cost rolling process, were evaluated. A near-gamma microstructure was obtained in the as-rolled condition. The microstructures of heat-treated sheets ranged from a recrystallized equiaxed near-gamma microstructure at 1,200 to 1,310 C, to a duplex microstructure at 1,350 C, to a fully lamellar microstructure at 1,376 C. Tensile behavior was determined for unidirectionally rolled and cross-rolled sheets for room temperature (RT) to 816 C. Yield stress decreased gradually with increasing deformation temperature up to 704 C; above 704 C, it declined rapidly. Ultimate tensile strength exhibited a gradual decrease up to 537 C before peaking at 704 C, followed by a rapid decline at 816 C. The modulus showed a gradual decrease with temperature, reaching approximately 72% of the RT value at 816 C. Strain to failure increased slowly from RT to 537 C; between 537 C and 704 C it exhibited a phenomenal increase, suggesting that the ductile-brittle transition temperature was below 704 C. Fracture mode changed from transgranular fracture at low temperature, to a mixture of transgranular and intergranular fracture at intermediate temperature, to ductile fracture at 816 C, coupled with dynamic recrystallization at large strains. Creep rupture response was evaluated between 649 and 816 C over the stress range of 69 to 276 MPa. Deformation parameters for steady-state creep rate and time-to-rupture were similar: activation energies of approximately 350 kJ/mol and stress exponents of approximately 4.5. Hot-die forming of sheets into corrugations was done at elevated temperatures in vacuum. The process parameters to join sheets by diffusion bonding and brazing with TiCuNi 70 filler alloy were optimized for test coupons and successfully used to fabricate large truss-core and honeycomb structures. Nondestructive evaluation methods, e.g., ultrasonic C-scans and thermography along with metallography, were used to characterize bond quality. Microstructural evaluation during heat treatment, identification of phases at the braze/matrix interface, determination of shear strengths of brazed joints, and deformation mechanisms during tensile and creep processes will be discussed.

Das, G.↗
DOE OSTI2019

An Investigation on Microstructure Evolution, Mechanical Properties, and Strain Aging of Mg-1.8Zn-0.7Si-0.4Ca Biomedical Alloy Processed by Equal Channel Angular Pressing

The influence of equal channel angular pressing (ECAP) on microstructure and mechanical behavior, as well as, strain aging during ECAP and post-ECAP of Mg-1.8Zn-0.7Si-0.4Ca biomedical alloy was examined. The alloy in solid solution heat-treated condition was processed by ECAP with route B{sub C} at 350 and 400 °C. The specimens ECAPed at 350 °C were aged at 125 and 150 °C for different times. The hardness and shear punch test results indicated that performing ECAP at 350 °C for 4 passes increases the hardness and shear strength of the alloy from 48 HV and 110 MPa to 71 HV and 188 MPa, respectively. It was revealed that the average grain size of the alloy decreases from 78 µm to about 3 µm after 4 passes of ECAP. Three precipitates of CaMgSi, Ca{sub 2}Mg{sub 6}Zn{sub 3}, and Mg{sub 2}Si were detected in the solid solution specimen. After 4 passes of ECAP at 350 °C, Ca{sub 2}Mg{sub 6}Zn{sub 3} was completely dissolved and the morphology of Mg{sub 2}Si changed from Chinese script to fiber-shaped particles. Dynamic strain aging occurred at high-temperature ECAP, and the specimens were overaged during post-ECAP aging. Small MgZn particles were detected in the overaged sample.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Constructing Crown Ether-Based Supramolecular Adhesives with Ambient-Temperature Applicable and Durable Adhesion

Supramolecular adhesives are attracting considerable attentions owing to their dynamic and reversible bonding, while the complex curing conditions and poor performance under extreme conditions severely restrict their applicability. Herein, a series of tetra-crown ether-terminated polyethylene glycol (TCE-PEG) adhesives are presented in which plenty of supramolecular interactions, including Van der Waals, hydrogen bonding, π–π staking, metal coordination, and electrostatic ones, provide strong adhesion on multiple types of substrates. Highly relevant for practical applications, ultra-strong adhesivity of TCE-PEG can be achieved without requiring additional ultraviolet radiation, heat, or chemical treatment at ambient temperature. It also exhibits durable adhesive behavior, excellent underwater stability, and low-temperature tolerance. Especially, by incorporating ionic polymer fragments of polyethyleneimine hydrochloride, additional hydrogen bonding between secondary amines and crown ether rings can be induced to enhance the lap-shear strength to 7.21 MPa due to the formation of supramolecular cross-linked network. Finally, this work pioneers a rather unique supramolecular approach for easily formed, ultra-strong crown-ether-based adhesives bearing great potential for applications in critical environments of limited heat source and unallowed solvent usage.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Electroplated Polymer‐Modified Carbon Fiber for Performance‐Enhancing Composite Interfaces

Carbon fiber composite performance relies on the fiber-matrix interface for effective load transfer. To enhance interfacial properties between the fiber and matrix, often carbon fiber surfaces are oxidatively and covalently modified to incorporate chemical functional groups. By contrast, here, noncovalent electrodeposition of functional polyelectrolyte is applied onto conducting carbon fibers from aqueous solutions. A natural polymer, chitosan (CS), is electro-deposited onto the fiber surface, which undergoes multi-scale physical interactions. The bound CS layer with abundant amine functionalities reacts with epoxy moieties within the matrix to improve the interfacial properties. The scalable and energy-efficient electrodeposition eliminates traditional functionalization and sizing requirements of carbon fiber while delivering significantly higher mechanical performance with enhanced consistency. For continuous fiber reinforced composites, compared to conventional fibers, apparent interlaminar shear strength increases by 27%, reaching ≈86 MPa. The short fiber composites with only 2–11 wt.% fibers exhibit ≈20% increase in tensile strength with a peak performance of 120 MPa. Unlike traditionally treated and sized carbon fiber, this approach delivers coated fibers with long shelf-life and allows recovery of both CS in electrolyte form and carbon fiber by continuous electrochemical processing of the modified fibers with inverse polarity; thus, it promotes overall fiber recyclability.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Interlaminar improvement of carbon fiber/epoxy composites via fluorine‐containing high‐epoxy‐value sizing agent

Abstract To improve the interfacial bonding effect of carbon fibers (CFs) and epoxy resins, we prepared a fluorine‐containing high‐epoxy‐value sizing agent (named TS) in this article. It is an emulsion with a more uniform particle size distribution and higher stability better than a commercial Takemoto sizing agent. In addition, sulfonic acid groups can improve the hydrophilicity of the TS, and the presence of epoxy groups enhances the wettability between CFs and the matrix. The properties of the sizing agents were examined by Fourier transform infrared spectroscopy, dynamic light scattering, and thermogravimetric analysis. The sized CFs were evaluated by scanning electron microscopy, x‐ray photoelectron spectroscopy, monofilament tensile test, and dynamic contact angle. Afterward, CF/epoxy composites were prepared, and their fracture morphology and interlaminar shear strength (ILSS) were examined. Results indicated that the TS sizing significantly increased the content of activated carbon on the surface of the CFs and improved the bonding effect between the fiber and the matrix. After TS was sized, the ILSS increased from 49.64 to 58.74 MPa, 18.34% higher than unsized CF/epoxy composites, showing the prominent interfacial reinforcement better than commercial Takemoto.

Qiu, Zhijie↗
DOE OSTI2021

An extended numerical manifold method for unsaturated soil-water interaction analysis at micro-scale

To investigate unsaturated soil-water interaction at micro-scale, this work extends the numerical manifold method (NMM) by incorporating a soil-water coupling model considering specific capillary water distribution and capillary force calculation. The soil skeleton is constructed by a soil skeleton generation algorithm with random polygons. To more realistically capture the interaction between soil grains and capillary water, a capillary mechanics-based geometric algorithm is proposed to iteratively calculate the capillary water distribution. The capillary forces corresponding to the capillary water distribution are calculated based on the Young-Laplace equation. The proposed capillary water solving framework is first verified by reproducing the soil-water characteristic curve and the capillary water distribution of an ideal contact-disk model against analytical solutions. To further validate the ability of the capillary water solving framework to predict hydraulic behavior of the real soil, a laboratory test on the Toyoura sand is reproduced numerically. Then an ideal direct shear test is performed to further validate the two-way soil-water coupling procedure, in which a comparison between the numerical and analytical results regarding the shear strength and matric suction is presented. Finally, microscopic hydraulic and compression tests are conducted on two soil specimens with the same porosity and mean grain diameter but different uniformity coefficients. The results elucidate that the extended method is a potential tool to explore unsaturated soil behaviors at micro-scale.

58 GEOSCIENCES↗
DOE OSTI2025

Hierarchically Structured Vitrimer Biocomposites for Sustainable Manufacturing

Polymers containing dynamic covalent bonds (DCBs) exhibit thermoplastic-like flow above their topology freezing temperature (T v ) while maintaining thermoset-like properties below it, making them promising for sustainable manufacturing. However, their large-scale adoption remains limited due to challenges in accurately determining T v and achieving efficient fiber-matrix bonding in composite applications. Here, hierarchically structured epoxy-anhydride-based polyester vitrimer composites reinforced with cellulosic filaments is demonstrated, where hydroxyl groups on fiber surfaces participate directly in transesterification with the matrix. Further, this dynamic interfacial bonding delivers exceptional mechanical properties, including ≈70 MPa shear strength and >10% strain-to-failure, while enabling thermal malleability. Using a combination of nuclear magnetic resonance and nano-infrared spectroscopies, direct evidence is provided that chemical bond exchange begins well below the conventionally measured T v , supporting the hypothesis that rheologically determined T v reflects a combination of chemical exchange and frictional dynamics rather than a discrete transition. The composites demonstrate excellent processability through vacuum-assisted resin transfer molding and maintain >90% of their mechanical properties after multiple thermal reforming cycles. These findings advance both the fundamental understanding of vitrimeric transitions and the practical development of sustainable, high-performance composite materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Effects of a composite flame retardant system on the flame retardancy and mechanical performance of epoxy resin adhesive

Abstract A flame‐retarded epoxy resin (ER) adhesive with strong flame retardancy and adhesion performance was prepared. The coated ammonium polyphosphate (MFAPP), melamine (MEL), and organic montmorillonite (OMMT) were mixed to prepare a composite flame retardant. It was subsequently blended with a toughened ER thoroughly and then the mixture was cured with polyamide. The resultant ER adhesive thermosets achieved UL‐94 V‐0 rating during vertical burning test, and the limiting oxygen index value was as high as 31.6%. The shear strength of the ER adhesive was 27.9 MPa when 25 wt% MFAPP/MEL/OMMT was introduced. Compared with the pure adhesive, the flame retardant epoxy adhesive maintained outstanding adhesion performance because of the good compatibility between the composite flame retardant additives and the toughened ER adhesive. Cone calorimetry tests indicated that the release of heat and smoke were obviously declined with the incorporation of the composite flame retardant system in comparison to pure ER adhesive thermoset. The investigation of flame retardant mechanism revealed that the composite MFAPP/MEL/OMMT flame retardant system stimulated the generation of highly expanded, integral, and strong char layer and the formed char layer exerted superior insulation effect during combusiton. The present work provided an alternative approach to prepare flame retardant ER adhesive with the similar excellent adhesive performance.

Li, Sheng↗
DOE OSTI2022

Structure of Shock Waves and Inelasticity in Shock-Compressed Cemented Tungsten Carbides

In this study, shock wave experiments are conducted on General Carbide cemented tungsten carbide with 3.7wt.% cobalt binder to determine its shock-induced compression behavior up to 100 GPa. The measured wave profiles indicate the cemented tungsten carbide to undergo elastic-plastic deformation during shock compression. A three-stage particle velocity profile is observed in the experiments -- an initial elastic-rise to the Hugoniot Elastic Limit (HEL), an elastic-plastic ramp indicating substantial post-yield hardening, and finally a rise to the peak shocked Hugoniot state. The results of the experiments are used to determine the HEL, the shock velocity (U s ) vs. particle velocity (u p ) Hugoniot relation, and the longitudinal stress (σ x ) vs. specific volume (V) curve for the samples. The HEL of the material was determined to lie between 4.41 GPa and 4.58 GPa. The U s - u p relation was determined to be U s = 4.97 + 1. 457u p for particle velocities greater than 0.75 km/s. The measured plastic shock velocities for particle velocities less than 0.7 km/s were found to be larger than those predicted using the linear U s - u p Hugoniot relationship, indicating the cemented WC samples to preserve substantial shear strength in the post-yield deformation region. No phase transformation was observed up to 100 GPa.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Dissimilar material joining of densified superwood to aluminum by adhesive bonding

Abstract Superwood is a densified wood product that shows promise as a lightweight and renewable alternative for metallic materials. In order for this high-performance new material to be used in multi-material products, it must be able to be joined with other major materials. For example, joining superwood to aluminum would provide a key enabling technology for its use in automotive components since aluminum is presently a major lightweight material for such applications. In this paper, a methacrylate-based adhesive has been identified to provide high lap shear strength (7.5 MPa) for aluminum-to-superwood joints. The aluminum-to-superwood samples were prepared with different amounts of pre-polishing to create openings to the pores in the superwood so adhesive could penetrate into them and create a mechanical interlock, in addition to the hydrogen/chemical bonding at the surface between the methyl methacrylate (MMA) in methacrylate-based adhesive and the cellulose in superwood. For aluminum samples, a thin layer (typically a few nanometers) of oxide film on the surfaces provides hydrogen/chemical bond to MMA structure in the adhesive layer. The failure strength of the superwood-to-aluminum joint sample is about 50% higher than that of natural wood to natural wood joint sample and comparable to that of aluminum-to-aluminum joint sample.

Automation & Control Systems↗
DOE OSTI2023

Plasma treatment on both adhesive tape and adherends for significantly enhanced CFRTP-related adhesive joints

Unlike existing literature that primarily concentrates on either the plasma treatment of adherends alone or solely on adhesive surfaces, this work leverages plasma modification of both adhesive in tape form and adherend surfaces to largely enhance the interfacial bonding between a thermoset-based adhesive tape and carbon-fiber-reinforced thermoplastic polymer (CFRTP) for structural bonding applications. Here, by conducting single lap shear tests on adhesively-bonded AA6061-CFRPPA (carbon-fiber-reinforced polyphthalamide) dissimilar joints, it is shown that the plasma treatment of adherends alone can increase the lap shear strength (LSS) of the joints by approximately 200% compared to non-treated counterparts. An additional plasma treatment of adhesive tape surfaces leads to even higher LSS improvement, reaching up to 315%, due to the formation of a denser crosslinked network of covalent bonds and a reduced area fraction of interfacial voids at the CFRPPA/adhesive interface. The highest plasma-enhanced LSS of the metal-CFRTP dissimilar joints rivals that of metal-metal joints, which is typically stronger than the joints associated with fiber-reinforced polymers. This study is important for achieving strong CFRTP-related structural components bonded using adhesive tape, providing better compatibility with plasma treatment and other joining methods like riveting compared to adhesive paste or liquid.

36 MATERIALS SCIENCE↗