Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STABILITY, LONGITUDINAL - STATIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Flight tests of a radio-controlled airplane mode with a free-wing, free-canard configuration

Flight characteristics, controllability, and potential operating problems were investigated in a radio-controlled airplane model in which the wing is so attached to the fuselage that it is free to pivot about a spanwise axis forward of its aerodynamic center and is subject only to aerodynamic pitching moments imposed by lift and drag forces and a control surface. A simple technique of flying the test vehicle in formation with a pickup truck was used to obtain trim data. The test vehicle was flown through a series of maneuvers designed to permit evaluation of certain characteristics by observation. The free-wing free-canard concept was determined to be workable. Stall/spin characteristics were considered to be excellent, and no effect on longitudinal stability was observed when center of gravity changes were made. Several problems were encountered during the early stages of flight testing, such as aerodynamic lockup of the free canard and excessive control sensitivity. Lack of onboard instrumentation precluded any conclusions about gust alleviation or ride qualities.

Gee, S. W.↗
NASA NTRS1978

Wind-tunnel investigation at Mach numbers from 1.90 to 2.86 of a canard-controlled missile with ram-air-jet spoiler roll control

The efficacy of using a ram-air-jet spoiler roll control device on a typical canard-controlled missile configuration was investigated. For roll control comparisons, conventional aileron controls on the tail fins were also tested. The results indicate that the roll control of the ram-air-jet spoiler tail fins at the highest free-stream Mach number compared favorably with that of the conventional 11-70 area-ratio tail fin ailerons, each deflected 10 deg. The roll control of the tail fin ailerons decreased while that of the ram-air-jet spoiler increased with free-stream Mach number. The addition of the ram-air-jet spoiler tail fins or flow-through tip chord nacelles on the tail fins resulted in only small changes in basic missile longitudinal stability. The axial force coefficient of the operating ram-air-jet spoiler is significantly larger than that of conventional ailerons and results primarily from the total pressure behind a normal shock in front of the nacelle inlets.

Blair, A. B., Jr.↗
NASA NTRS1976

Summary of low-speed aerodynamic characteristics of upper-surface-blown jet-flap configurations

The results of recent wind tunnel investigations to provide fundamental information on the upper surface blown (USB) jet flap concept demonstrated that the USB concept provides good high-lift performance. It is shown that the low speed performance is dependent upon the jet turning angle and turning efficiency and on the use of proper leading and trailing edge treatment to prevent premature flow separation. The best means of achieving good turning performance in any particular USB application must be determined from overall operational considerations in which high speed performance, structures and noise, as well as low speed performance, are evaluated. The large diving moments generated at high lift coefficients can be trimmed satisfactorily with a large, conventional horizontal tail; a high tail position is best from longitudinal stability considerations. Large rolling and yawing moments are introduced with the loss of an engine, but these moments can be trimmed satisfactorily through the use of asymmetrical boundary layer control and through the use of spoiler and rudder deflection as needed.

Phelps, A. E., III↗
NASA NTRS1978

Supersonic transport

An aircraft of supersonic transport configuration is described, featuring thrust vectoring in conjunction with wing apex segments used as canard surfaces during takeoff, landing, and low-speed flight. The angle of incidence of the wing apex segments, when the segments were functioning as canard surfaces, was variable with respect to the aircraft angle of attack. The wing apex segments furthermore formed a portion of the main wing panel swept leading edge when not functioning as canard surfaces. The combination of thrust vectoring and deployable wing apex segments resulted in increased aircraft range and improved low speed longitudinal stability while providing acceptable takeoff length capabilities.

Coe, P. L., Jr.↗
NASA NTRS1979

Experimental study of the flight envelope and research of safety requirements for hang-gliders

The flight mechanic computations were computed, providing both the flight envelopes with all sorts of limits and a fairly precise idea of the influence of several parameters, such as pilot's weight, wing settings, aeroelasticity, etc... The particular problem of luffing dives was thoroughly analyzed, and two kinds of causes were exhibited in both the rules of luffing and aeroelastic effects. The general analysis of longitudinal stability showed a strong link with fabric tension, as expected through Nielsen's and Twaites' theory. Fabric tension strongly depending upon aeroelasticity, that parameter was found to be the most effective design one for positive stability. Lateral stability was found to be very similar in all gliders except perhaps the cylindro-conical. The loss of stability happens in roll at low angle of attack, whereas it happens in yaw at high angle. Turning performance was a bit suprising, with a common maximum value of approximately 55 deg of bank angle for a steady turn.

Laburthe, C.↗
NASA NTRS1981

Wind-tunnel investigation of the tail-spoiler concept for stall-prevention on general aviation airplanes

The longitudinal aerodynamic characteristics of a full scale, single engine general aviation airplane equipped with an angle of attack limiting concept which used a tail mounted spoiler for stall prevention were investigated. The tail spoiler was deployed as a nonlinear function of changes in angle of attack in a narrow angle of attack range immediately preceding the stall angle. Spoiler deployment produced a nose down moment which limited the nose up trim capability of the elevator to an angle of attack below the stall angle of the airplane. The tail spoiler system produced significant increases in longitudinal stability and elevator hinge moments near the stall. The effects of power, flaps, and center of gravity position are also studied.

Satran, D. R.↗
NASA NTRS1982

Summary of theoretical considerations and wind tunnel tests of an aerodynamic spoiler for stall proofing a general aviation airplane

An airplane stall proofing system utilizing a spoiler was investigated for application on a low wing airplane representative of typical general aviation aircraft. Tests of the full scale airplane were conducted in the NASA Langley 30 x 60 foot full scale wind tunnel. The test velocity was 86 feet per second, corresponding to a Reynolds number of 2.20 million. The stall proofing capability of the spoiler is shown and a theoretical approach to the design of the spoiler and analysis of the spoiler's contribution to the airplane's trim and longitudinal stability is verified. Controlled spoiler deployment in a narrow angle of attack range, 4 degrees, immediately preceding the stall angle will stall proof the airplane. The results also show some of the limitations of flight tests to determine spoiler deployment rate for good handling qualities.

Chevalier, H. L.↗
NASA NTRS1981

Aerodynamic characteristics of a series of airbreathing missile configurations

Due to the interest in the application of airbreathing propulsion to missiles and the lack of a suitable data base, an experimental program has been conducted to contribute to such a data base. The configurations investigated were with twin-inlets, either two-dimensional or axisymmetric, each located at three circumferential locations. The effects of a wing located above the inlets and of tail configuration were investigated. Longitudinal stability and control and lateral-directional stability were included in the data obtained. This paper presents a summary of the program and some of the results obtained. Certain trends of the data, as well as problem areas, are discussed. Due to the large volume of data obtained, a detailed analysis is not presented.

Hayes, C.↗
NASA NTRS1982

Longitudinal control effectiveness and entry dynamics of a single-stage-to-orbit vehicle

The classical theory of flight dynamics for airplane longitudinal stability and control analysis was extended to the case of a hypervelocity reentry vehicle. This includes the elements inherent in supersonic and hypersonic flight such as the influence of the Mach number on aerodynamic characteristics, and the effect of the reaction control system and aerodynamic controls on the trim condition through a wide range of speed. Phugoid motion and angle of attack oscillation for typical cases of cruising flight, ballistic entry, and glide entry are investigated. In each case, closed form solutions for the variations in altitude, flight path angle, speed and angle of attack are obtained. The solutions explicitly display the influence of different regions design parameters and trajectory variables on the stability of the motion.

Vinh, N. X.↗
NASA NTRS1982

Quadratic synthesis of integrated active controls for an aeroelastic forward-swept-wing-aircraft

State variable representations of flexible aircraft are obtained using a modeling approach which first defines a mean-reference axis coordinate system. The active system design approach for forward-swept-wing aircraft also expresses structural deformations of the wing in terms of free normal vibration modes relative to this mean reference axis. Calculations which assume quasi-steady incompressible aerodynamics are performed to obtain generalized force expressions for flight conditions. The use of this quadratic synthesis technique shows that increased performance and redundancy over decentralized approaches can be achieved using integrated active longitudinal stability augmentation and aeroelastic stabilization.

Gilbert, M. G.↗
NASA NTRS1983

Trimming high lift for STOL fighters

The results of investigations of three different approaches to obtaining longitudinal trim for advanced fighter configurations with STOL performance are presented. The first, a differential thrust vectoring/reverser nozzle on an F-15 model, was very effective with an increment in pitching moment generated by the 90 deg/50 deg nozzle at military power equal to that which would be produced by a change in horizontal tail deflection of 20 deg. This trim pitching moment was accompanied by a modest loss in lift. The second method involved a nose jet on a supersonic cruise fighter configuration which, when combined with some canard deflection and longitudinal instability, provided trim capability for the configuration with military power setting and main nozzles deflected 43 degrees. Finally, a blown-high-lift canard on an advanced fighter configuration indicated that trim could be obtained across the complete angle-of-attack range tested with thrust set at military power and the main nozzles deflected 40 degrees. There was no loss in configuration lift and a slight increase in longitudinal stability.

Paulson, J. W., Jr.↗
NASA NTRS1983

Some lessons from NACA/NASA aerodynamic studies following World War II

An historical account is presented of the new departures in aerodynamic research conducted by NACA, and subsequently NASA, as a result of novel aircraft technologies and operational regimes encountered in the course of the Second World War. The invention and initial development of the turbojet engine furnished the basis for a new speed/altitude regime in which numerous aerodynamic design problems arose. These included compressibility effects near the speed of sound, with attendant lift/drag efficiency reductions and longitudinal stability enhancements that were accompanied by a directional stability reduction. Major research initiatives were mounted in the investigation of swept, delta, trapezoidal and variable sweep wing configurations, sometimes conducted through flight testing of the 'X-series' aircraft. Attention is also given to the development of the first generation of supersonic fighter aircraft.

Spearman, M. L.↗
NASA NTRS1984

Vortex flaps - Advanced control devices for supercruise fighters

Prompted by the extensive experience obtained with vortex lift-generating leading edges in the SR-71, Concorde and F-16 supersonic aircraft, development efforts have recently been made toward the use of variable incidence angle delta wing leading edge 'vortex flaps' for supersonic cruise and maneuvering performance improvements in fighter aircraft. Vortex lift flaps have been wind tunnel tested on scale models, and it has been noted that a variety of effects can be obtained through the use of folding, hinged, and tabbed flap designs. Flap planforms can, moreover, be varied in length and in total area, as well as segmented, to yield unique combinations of drag reduction, vortex generation, longitudinal stability, and vortex flow reattachment. It is speculated that the vortex flap may be applicable to multimission fighters, and promote STOL performance.

Lamar, J. E.↗
NASA NTRS1984

Development of flight testing techniques

A list of students involved in research on flight analysis and development is given along with abstracts of their work. The following is a listing of the titles of each work: Longitudinal stability and control derivatives obtained from flight data of a PA-30 aircraft; Aerodynamic drag reduction tests on a box shaped vehicle; A microprocessor based anti-aliasing filter for a PCM system; Flutter prediction of a wing with active aileron control; Comparison of theoretical and flight measured local flow aerodynamics for a low aspect ratio fin; In flight thrust determination on a real time basis; A comparison of computer generated lift and drag polars for a Wortmann airfoil to flight and wind tunnel results; and Deep stall flight testing of the NASA SGS 1-36.

Sandlin, D. R.↗
NASA NTRS1986

PAN AIR application to the F-106B

The PAN AIR computer code was employed in the present study to investigate the aerodynamic effects of the various geometrical changes and flow conditions on a configuration similar to the F-106B half-airplane tested in the Langley 30x60-foot wind tunnel. The various geometries studied included two forebodies (original and shortened), two inlet flow conditions (open and closed) two vortex flap situations (off and on). The attached flow theoretical solutions were obtained for Mach number of 0.08 and angle of attack of 8 deg., 10 deg., 12 deg., and 14 deg. In general this investigation revealed that the shortening of the forebody or closing of the inlet produced only a small change in the overall aerodynamic coefficients of the basic F-106B configuration throughout the examined angles of attack. However, closing the inlet of the configuration resulted in a slightly higher drag level at low angles of attack. Furthermore, at and above 10 deg. angle of attack, it was shown that the presence of the vortex flap causes an increase in the total lift and drag. Also, these theoretical results showed the expected reduction in longitudinal stability level with addition of the vortex flap to the basic F-106B configuration.

Farhad Ghaffari↗
NASA NTRS1986

Nonlinear lift control at high speed and high angle of attack using vortex flow technology

Nonlinear lift control at subsonic, transonic and low supersonic speeds owes its origin to the separated but organized vortical flows interacting with the wing upper surface. Since most of this flow originates near the wing or control-surface leading-edge, a variety of devices have been studied experimentally which interact with and/or control this flow in order to gain a beneficial effect. The benefits (effects) originally studied were only associated with lift enhancement. Whereas, now the studied benefits encompass performance increase, attention to changes in trimmed conditions and longitudinal stability, improvements in lateral stability, and the attendant variation with changing Mach number. For those devices that can be theoretically modeled, state-of-the-art computer codes have been used for device design and/or analysis. Comparisons at design and off-design conditions are presented for validation purposes.

Lamar, J. E.↗
NASA NTRS1986

Over-the-wing propeller

This invention is an aircraft with a system for increasing the lift drag ratio over a broad range of operating conditions. The system positions the engines and nacelles over the wing in such a position that gains in propeller efficiency is achieved simultaneously with increases in wing lift and a reduction in wing drag. Adverse structural and torsional effects on the wings are avoided by fuselage mounted pylons which attach to the upper portion of the fuselage aft of the wings. Similarly, pylon-wing interference is eliminated by moving the pylons to the fuselage. Further gains are achieved by locating the pylon surface area aft of the aircraft center of gravity, thereby augmenting both directional and longitudinal stability. This augmentation has the further effect of reducing the size, weight and drag of empennage components. The combination of design changes results in improved cruise performance and increased climb performance while reducing fuel consumption and drag and weight penalties.

Johnson, Joseph L., Jr.↗
NASA NTRS1987

Nonlinear lift control at high speed and high angle of attack using vortex flow technology

Nonlinear lift control at subsonic, transonic and low supersonic speeds owes its origin to the separated but organized vortical flows interacting with the wing upper surface. Since most of this flow originates near the wing or control-surface leading edge, a variety of devices has been studied experimentally which interact with and/or control this flow in order to gain a beneficial effect. The benefits (effects) originally studied were associated only with lift enhancement. Whereas, now the studied benefits encompass performance increase, attention to changes in trimmed conditions and longitudinal stability, improvements in lateral stability, and the attendant variation with changing Mach number. For those devices that can be theoretically modeled, state-of-the-art computer codes have been used for device design and/or analysis. Comparisons at design and off-design conditions are presented for validation purposes.

Lamar, John E.↗