Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SILICON OXIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Large Area Transfer of Bismuth‐Based Layered Oxide Thin Films Using a Flexible Polymer Transfer Method

Magnetic and ferroelectric oxide thin films have long been studied for their applications in electronics, optics, and sensors. The properties of these oxide thin films are highly dependent on the film growth quality and conditions. To maximize the film quality, epitaxial oxide thin films are frequently grown on single-crystal oxide substrates such as strontium titanate (SrTiO 3 ) and lanthanum aluminate (LaAlO 3 ) to satisfy lattice matching and minimize defect formation. However, these single-crystal oxide substrates cannot readily be used in practical applications due to their high cost, limited availability, and small wafer sizes. One leading solution to this challenge is film transfer. In this demonstration, a material from a new class of multiferroic oxides is selected, namely bismuth-based layered oxides, for the transfer. A water-soluble sacrificial layer of Sr 3 Al 2 O 6 is inserted between the oxide substrate and the film, enabling the release of the film from the original substrate onto a polymer support layer. The films are transferred onto new substrates of silicon and lithium niobate (LiNbO 3 ) and the polymer layer is removed. These substrates allow for the future design of electronic and optical devices as well as sensors using this new group of multiferroic layered oxide films.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of point defects on oxidation of 3C–SiC

The influence of implantation-induced point defects (PDs) on SiC oxidation is investigated via molecular dynamics simulations. PDs generally increase the oxidation rate of crystalline grains. Particularly, accelerations caused by Si antisites and vacancies are comparable, and followed by Si interstitials, which are higher than those by C antisites and C interstitials. However, in the grain boundary (GB) region, defect contribution to oxidation is more complex, with C antisites decelerating oxidation. Here, the underlying reason is the formation of a C-rich region along the oxygen diffusion pathway that blocks the access of O to Si and thus reduces the oxidation rate, as compared to the oxidation along a GB without defects.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Stable and selective catalysts for propane dehydrogenation operating at thermodynamic limit

Hitting the limits on propene synthesis The greater abundance of propane from shale gas has spurred efforts to use it as a propylene feedstock. Direct dehydrogenation catalysts consisting of platinum–tin alloy nanoparticles supported on alumina often must run with hydrogen dilution to avoid carbon buildup and excess tin to avoid alloy segregation. Motagamwala et al. report that platinum–tin nanoparticles interact more weakly with a silica support and the metals thus do not segregate. The use of undiluted reactants allowed the reaction to run near the thermodynamically limit of about 67% conversion with a selectivity to propylene of more than 99%. This catalyst also does not build up carbon and could run up to 30 hours without deactivation. Science , abg7894, this issue p. 217

Science & Technology - Other Topics↗
DOE OSTI2022

The influence of cooling rate on condensation of iron, aluminum, and uranium oxide nanoparticles

Fundamental observations of particle size distributions are needed to develop models that predict the fate and transport of radioactive materials in the atmosphere following a nuclear incident. The extent of material transport is influenced by the time scales of particle formation processes (e.g., condensation, coagulation). In this study, we investigated the influence of cooling time scales on size distributions of uranium, aluminum, and iron oxide particles that are synthesized separately under identical run conditions inside the controlled environment of an argon plasma flow reactor. Two distinct temperature distributions are imposed along the flow reactor by varying the argon flow rate downstream of the plasma torch. The vaporized reactants of uranium, aluminum, and iron are cooled from about 5000K to 1000K before they are collected on silicon wafers for ex situ scanning electron microscope analysis. The microscope images show that the sizes of the largest aluminum and iron oxide particles heavily depend on the cooling time scales, whereas significant size variation with cooling rate is not observed for uranium oxide particles. In addition, the size distribution of aluminum oxide particles exhibits the broadest range among all three metal oxides studied. We performed simulations of particle size distributions using a kinetic model that couples gas phase oxidation chemistry with particle formation processes, including nucleation, condensation, and coagulation. The model results demonstrate the strong sensitivity of particle size distribution to different cooling histories (i.e., temperature vs residence time) along the flow reactor. In conclusion, the kinetic model also helps identify directions for future research to improve the predictions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Quality Control Methods for Measurement of UCO Kernel Composition and SiC Microstructure

Quality control (QC) is critically important to tristructural-isotropic (TRISO) particle fuels owing to the complexity of and reliance on the fuel form to contain fission products during irradiation. Characterization methods for particle fuel QC have decades of history and have continued to develop as new insights into fuel performance inform revised fuel specifications and as advances in underlying technologies expand the possibilities of what may be characterized. Two relatively new methods for characterization of TRISO fuels have been published in open literature: optical microscopy image analysis for mixed uranium carbide/uranium oxide (UCO) kernel composition analysis and automated grain boundary detection in backscattered electron (BSE) images of the silicon carbide (SiC) layer in TRISO particles for grain size characterization. Suggestions and guidelines for the application of these methods to TRISO fuel qualification are provided in this report.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Aluminum Boron Nitride Ferroelectric Field-Effect Transistors With ZnO Semiconductor Channel

The discovery of ferroelectricity in hafnium zirconium oxide (HfxZr 1−x O2) and related fluorite materials has spurred interest in ferroelectric devices suitable for integration with silicon integrated circuits (ICs), especially those that can be embedded in the back-end-of-line (BEOL) process. More recently, ferroelectricity has been found in wurtzite aluminum nitride-based materials, such as scandium and boron-doped aluminum nitride (Al 1−x ScxN and Al 1−x BxN). Although these materials currently have undesirably large coercive electric fields, and small breakdown electric field-to-coercive electric field ratio, their low processing temperatures and large remanent polarization offer intriguing possibilities for device applications. Furthermore, we report ferroelectric field-effect transistors (FeFETs) with a 15 nm thick Al0.88B0.12N layer and an 11 nm ZnO semiconductor channel, achieving a memory window >1 V and switching voltages ( V switch ) <±10 V.

42 ENGINEERING↗
DOE OSTI2025

A Reduced-Temperature Process for Preparing Atomically Clean Si(100) and SiGe(100) Surfaces with Vapor HF

Silicon processing techniques such as atomic precision advanced manufacturing (APAM) and epitaxial growth require surface preparations that activate oxide desorption (typically >1000 °C) and promote surface reconstruction toward atomically clean, flat, and ordered Si(100)-2 × 1. Here, in this study, we compare the aqueous and vapor phase cleaning of Si and Si/SiGe surfaces to prepare APAM-ready and epitaxy-ready surfaces at lower temperatures. Angle resolved X-ray photoelectron spectroscopy (ARXPS) and Fourier transform infrared (FTIR) spectroscopy indicate that vapor hydrogen fluoride (VHF) cleans dramatically reduce carbon surface contamination and allow the chemically prepared surface to reconstruct at lower temperatures, 600 °C for Si and 580 °C for a Si/Si 0.7 Ge 0.3 heterostructure, into an ordered atomic terrace structure indicated by scanning tunneling microscopy (STM). After thermal treatment and vacuum hydrogen termination, we demonstrate STM hydrogen desorption lithography (HDL) on VHF-treated Si samples, creating reactive zones that enable area-selective chemistry by using a thermal budget similar to CMOS process flows. We anticipate that these results will establish new pathways to integrate APAM with Si foundry processing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Synthesis and Characterization of Silicon Carbide Ceramic Composites with CeO 2 Powder

This study pioneers the fabrication and characterization of silicon carbide (SiC) containing cerium dioxide (CeO 2 ). CeO 2 powder was tested as a surrogate for actinide oxide waste forms such as uranium dioxide (UO 2 ) and plutonium dioxide (PuO 2 ). Several syntheses were evaluated with varying amounts of preceramic polymer (SMP-10 resin) and CeO 2 containing either SiC fiber, carbon fiber, or no fibers. Scanning electron microscopy (SEM) was used to characterize morphology and compositional differences, and energy-dispersive x-ray spectroscopy (EDS) was used to provide semiquantitative elemental analysis. In addition, each sample was characterized by density, powder x-ray diffraction (pXRD), and Raman spectroscopy. Samples containing nearly more than four times CeO 2 powder than SMP-10 resin by mass had the best properties. This research establishes a unique synthesis for SiC containing high concentrations of CeO 2 powder to illustrate how it may be managed as a potential waste form.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Efficient passivation of n-type and p-type silicon surface defects by hydrogen sulfide gas reaction

An efficient surface defect passivation is observed by reacting clean Si in a dilute hydrogen sulfide-argon gas mixture (< 5% H2S in Ar) for both n-type and p-type Si wafers with planar and textured surfaces. Surface recombination velocities of 1.5 and 8 cm/s are achieved on n-type and p-type Si wafers, respectively, at an optimum reaction temperature of 550oC that are comparable to the best surface passivation quality used in high efficiency Si solar cells. Surface chemical analysis using x-ray photoelectron spectroscopy shows that sulfur is primarily bonded in a sulfide environment, and synchrotron-based soft x-ray emission spectroscopy of the adsorbed sulfur atoms suggests the formation of S-Si bonds. Furthermore, the sulfur surface passivation layer is unstable in air, attributed to surface oxide formation and a simultaneous decrease of sulfide bonds. However, the passivation can be stabilized by a low-temperature (300oC) deposited amorphous silicon nitride (a-Si:NX:H) capping layer.

14 SOLAR ENERGY↗
DOE OSTI2022

Control of High-Temperature Static and Transient Thermomechanical Behavior of SiMo Ductile Iron by Al Alloying

Abstract Silicon and molybdenum ( SiMo ) ductile iron is commonly used for exhaust manifolds because these components experience thermal cycling in oxidizing environment, which requires resistance to fatigue during transient thermomechanical loads. Previous studies have demonstrated that alloying elements, such as Al , to SiMo ductile iron reduces the amount of surface degradation during static high-temperature exposure. However, deterioration of sphericity of the graphite nodules and a decrease in ductility could affect the tendency of cracking during thermal cycling. In this article, the effect of Al alloying on static and transient thermomechanical behavior of SiMo ductile iron was investigated to optimize the amount of Al alloying. A thermodynamic approach was used to confirm the effect of the Al alloying on the phase transformations in two SiMo cast irons, alloyed by 1.8% Al and 3% Al . These two alloys were cast in a laboratory along with the baseline SiMo ductile iron. Several experimental methods were used to evaluate the dimensional stability, physical properties, static oxidation, and failure resistance during constrained thermal cycling testing to compare their high-temperature capability. Experimental results verified that Al alloying increases the temperature range and decreases volume change during eutectoid transformation, which together with enhancement of oxidation protection improved the dimensional stability. Thermocycling tests showed that the number of cycles to failure depends on the amount of Al alloying and the applied high-temperature exposure during each cycle. SEM/EDX, high-resolution TEM and µCT analysis were used to verify the mechanism resulting from the Al alloying protection. It was shown that an optimal level of Al alloying for balancing oxidation and thermal cracking resistance depends on thermomechanical conditions of application.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Surface Reconstruction in Hydrated Amphiphilic Block Copolymer Thin Films Probed by Fluid Cell Atomic Force Microscopy

In many thin film materials, nuanced interplays of interfacial energies control the surface morphology and rearrangement. This work evaluates polymer−solvent interactions and solvent-driven surface reconstructions via ex situ and in situ fluid cell Atomic Force Microscopy (fc-AFM) analysis of amphiphilic block copolymer (BCP) thin films upon exposure to deionized (DI) water. We examine the differences in surface morphology, whole-film swelling, and force response in thin films of polystyrene-block-poly(ethylene oxide) (PS-b-PEO) and polystyrene- block-poly[(allyl glycidyl ether)-co-(ethylene oxide)] (PS-b- P[AGE-co-EO]) processed into standing-up cylinder morphologies perpendicular to a silicon substrate (⊥C). Using Amplitude Modulation AFM (AM-AFM) and Amplitude-Phase Distance (APD) force spectroscopy, this work probes the mechanoresponsive nature of the dynamic surface layers of these films, unveiling surface layer stratification and surface chain rearrangement via minimal tip−sample stimulation. To help rationalize the observed reconfigurations, the energetic driving forces were estimated using the harmonic mean approximations of interfacial energies. Given the nonionizable nature of the minority P(AGE-co-EO) block and the energetic driving forces for chain mobility, this work shows how the elimination of unfavorable PS−water interfaces drives chain rearrangement and coverage of the PS surface by chains of the hydrophilic block. This work highlights considerations for increasing the heterogeneity and complexity of BCP thin films via random blocks and how those changes to local interfacial energies may drive larger scale film morphology reconstructions, with broader implications for tuning interface hydrophilicity.

Copolymers↗
DOE OSTI2022

High-resolution Compton spectroscopy using x-ray microcalorimeters

X-ray Compton spectroscopy is one of the few direct probes of the electron momentum distribution of bulk materials in ambient and operando environments. Herein, we report high-resolution inelastic x-ray scattering experiments with high momentum and energy transfer performed at a storage-ring-based high-energy x-ray light source facility using an x-ray transition-edge sensor (TES) microcalorimeter detector. The performance was compared with a silicon drift detector (SDD), an energy-resolving semiconductor detector, and Compton profiles were measured for lithium and cobalt oxide powders relevant to lithium-ion battery research. Spectroscopic analysis of the measured Compton profiles demonstrates the high-sensitivity to the low- Z elements and oxidation states. The line shape analysis of the measured Compton profiles in comparison with computed Hartree–Fock profiles is usually limited by the resolution of the semiconductor detector. We have characterized an x-ray TES microcalorimeter detector for high-resolution Compton scattering experiments using a bending magnet source at the Advanced Photon Source with a double crystal monochromator, providing monochromatic photon energies near 27.5 keV. The momentum resolution below 0.16 atomic units (a.u.) was measured, yielding an improvement of more than a factor of 7 over a state-of-the-art SDD for the same scattering geometry. Furthermore, the lineshapes of narrow valence and broad core electron profiles of sealed lithium metal were clearly resolved using an x-ray TES compared to smeared and broadened lineshapes observed when using the SDD. High-resolution Compton scattering using the energy-resolving area detector shown here presents new opportunities for spatial imaging of electron momentum distributions for a wide class of materials with applications ranging from electrochemistry to condensed matter physics.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Mild-Annealed Molecular Layer Deposition (MLD) Tincone Thin Film as Photoelectrochemically Stable and Efficient Electron Transport Layer for Si Photocathodes

Metalcone thin films, composed of inorganic–organic hybrids, are synthesized using molecular layer deposition (MLD) through reactions between organometallic precursors (e.g., Sn, Al, and Ti) and organic reactants (e.g., ethylene glycol and glycerol). Despite their unique properties, metalcones exhibit significant vulnerability to water due to their organic components, limiting their potential in electrochemical applications. This study focuses on enhancing the photoelectrochemical stability of tincone thin films in aqueous electrolyte while preserving their hybrid characteristics through mild annealing in air at 250 °C. As-deposited and vacuum-annealed tincone thin films exhibited significant degradation under these conditions, while high-temperature-annealed (500 °C) tincone thin films offered improved stability with a significant decline in charge transfer efficiency. In contrast, mild annealing in air maintained the C–O bond at half level and improved the stability and charge transport without compromising the unique characteristics of tincone. This was confirmed by ellipsometry, X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FTIR). Mild-annealed tincone deposited on a lightly doped p-type silicon (p-Si) photocathode produced a 20-fold increase in CO volume compared to high-temperature annealed tincone in a CO 2 -saturated potassium bicarbonate (KHCO 3 ) electrolyte with dispersed graphene oxide–cobalt phthalocyanine (GO-CoPc) under 1 sun illumination at 0.9 V vs reversible hydrogen electrode (RHE), while maintaining the faradaic efficiency for CO and H 2 . These results suggest that mild-annealed tincone thin films hold significant potential as protective charge transport layers on silicon photocathodes for the aqueous CO 2 reduction reaction (CO 2 RR).

Annealing (metallurgy)↗
DOE OSTI2020

Oxidation of the Interiors of Carbide Exoplanets

Astrophysical measurements have shown that some stars have sufficiently high carbon-to-oxygen ratios such that the planets they host would be mainly composed of carbides instead of silicates. We studied the behavior of silicon carbide in the presence of water under the high pressure–temperature conditions relevant to planetary interiors in the laser-heated diamond-anvil cell. When reacting with water, silicon carbide converts to silica (stishovite) and diamond at pressures up to 50 GPa and temperatures up to 2500 K: $\mathrm{SiC}+2{{\rm{H}}}_{2}{\rm{O}}\to {\mathrm{SiO}}_{2}+{\rm{C}}+2{{\rm{H}}}_{2}$. Therefore, if water can be incorporated into carbide planets during their formation or through later delivery, they could be oxidized and have mineralogy dominated by silicates and diamond in their interiors. The reaction could produce CH 4 at shallower depths and H 2 at greater depths that could be degassed from the interior, causing the atmospheres of the converted carbon planets to be rich in reducing gases. Excess water after the reaction can be stored in dense silica polymorphs in the interiors of the converted carbon planets. Such conversion of mineralogy to diamond and silicates would decrease the density of carbon-rich planet, making the converted planets distinct from silicate planets in mass–radius relations for the 2–8 Earth mass range.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Varistors: A Useful Tool for Superconducting Magnet Quench Protection

A perfect varistor is a constant voltage resistor as a function of current through the resistor. A perfect varistor can't exist, because its resistance would be infinite at zero current. In electronic devices, varistors are often used as surge protectors. A varistor can be used in place of an ordinary resistor as the discharge resistance across superconducting coil sections. When used this way, the integral of I 2 dt during the discharge can be reduced by almost one third. When a varistor is used for quench protection of coils that are coupled to shorted secondary circuits the integral of I 2 dt can be reduced much more. Furthermore, this can be a key factor when coil current densities and stored energies are high as in many potential HTS magnet systems. This paper discusses the types of varistors that are commercially available and their characteristics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Screen-Printed SHJ Solar Cells with Complex Silver Inks

Metallization using complex metal inks has gained significant research interest due to its cost-effectiveness and ability to achieve performance comparable to traditional nanoparticle pastes. This study introduces the use of complex silver (Ag) inks applied via industrial screen-printing for silicon heterojunction (SHJ) solar cell metallization. The printed Ag lines exhibit a contact resistivity on SHJ tin-doped indium oxide (ITO) surfaces as low as approximately 0.2-12 mO cm2. Photoluminescence imaging reveals minimal surface passivation degradation (iVoc < 3.5 mV), while scanning electron microscopy (SEM) shows a denser structure compared to Ag layer from nanoparticle pastes. The printed Ag grid features thin (approximately 1 micrometer), continuous fingers approximately 100-120 micrometer wide, significantly thinner than conventional approximately 20-30 micrometer fingers produced with nanoparticle-based pastes. Double printing achieves SHJ device efficiencies exceeding 20%, the highest reported for industrial solar cell precursors using this technology. These findings highlight the potential of complex Ag inks as a sustainable alternative to particle-based pastes, reducing Ag consumption and processing temperatures without compromising efficiency.

14 SOLAR ENERGY↗
DOE OSTI2024

Impacts of Curing-Induced Phase Segregation in Silicon Nanoparticle-Based Electrodes

We report the investigation of silicon nanoparticle composite anodes for Li-ion batteries, using a combination of two nm-scale atomic force microscopy-based techniques: scanning spreading resistance microscopy for electrical conduction mapping and contact resonance and force volume for elastic modulus mapping, along with scanning electron microscopy-based energy dispersion spectroscopy, nanoindentation, and electrochemical analysis. Thermally curing the composite anode—made of polyethylene oxide-treated Si nanoparticles, carbon black, and polyimide binder—reportedly improves the anode electrochemical performance significantly. This work demonstrates phase segregation resulting from thermal curing, where alternating bands of carbon and silicon active material are observed. This electrode morphology is retained after extensive cycling, where the electrical conduction of the carbon-rich bands remains relatively unchanged, but the mechanical modulus of the bands decreases distinctly. These electrical and mechanical factors may contribute to performance improvement, with carbon bands serving as a mechanical buffer for Si deformation and providing electrical conduction pathways. This work motivates future efforts to engineer similar morphologies for mitigating capacity loss in silicon electrodes.

25 ENERGY STORAGE↗