Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SI”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Beneficial Effect of Li 5 FeO 4 Lithium Source for Li-Ion Batteries with a Layered NMC Cathode and Si Anode

The energy density of lithium-ion batteries can be increased by replacing the traditional graphite anode with a high capacity silicon anode. However, volume changes and interfacial instabilities cause a large irreversible capacity and a continual loss of lithium during cycling, which lead to rapid capacity loss. In this work, we add Li 5 FeO 4 (LFO) to a LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC) cathode as a pre-lithiation additive, which increases the lithium inventory and extends the cycle life of Si-graphite/NMC full cells, and decreases the NMC particle degradation. LFO delivers a large 764 mAh g –1 LFO capacity below 4.7 V vs Li/Li + . By tuning the LFO content in Si-graphite/LFO-NMC full cells, we show higher capacity, improved retention, lower impedance, and superior rate performance compared to full cells without LFO. Post-test characterizations demonstrate that LFO inclusion in the cathode matrix leads to less NMC secondary particle segregation/cracking and a thinner surface reduced layer on the NMC particles. The beneficial effects of LFO endure after the lithium reserve has been exhausted, highlighting a lasting synergy between the lithium source and electrode active materials. This study introduces a new approach to simultaneously increase lithium inventory and reduce cathode degradation, and makes critical advances toward enabling Si anodes for lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Development of ~25% Efficient Double Side Screen Printed Poly-Si/SiO x Passivated Contact Solar Cells

This program aims to overcome these challenges and develop high-efficiency (24-25%) double-side (DS) TOPCon solar cells by maximizing passivation on both sides while mitigating light absorption losses. To achieve this, the program will implement either thin (≤ 20 nm) homogeneous n-TOPCon on the entire front surface or selective area thick (≥ 100 nm) n-TOPCon only underneath the front metal contact with ~90% field region composed of dielectric passivated textured n-Si in between the poly-Si/metal grid. The rear side will feature ~250 nm-thick full-area planar p-TOPCon, which functions as the rear junction. Recombination and parasitic absorption losses in the front and rear TOPCon layers will be minimized by tailoring their doping profiles and thickness. Additionally, the device performance will be further enhanced through the optimization of bulk parameters, including the carrier lifetime, resistivity, and thickness of the n-type Si absorber. Finally, advanced metallization techniques, such as fine-line printing, and floating busbar or busbar-less designs, will be employed to reduce recombination, resistive, and optical losses. The program started with the development of a technology roadmap for DS-TOPCon cells to achieve target efficiency.

14 SOLAR ENERGY↗
DOE OSTI2023

Linearized Distribution Optimal Power Flow for OEDI SI

This research is to meant to demonstrate the OEDI SI use case for distributed optimal power flow (DOPF). The goal was to formulate the optimal power flow problem in the distribution system for active and reactive power setpoints of PV systems using topology information and voltage measurements. The co-simulation runs every 15 minutes as outlined within the scenario file for the given feeder configuration. The linked GitHub repository includes five federates to achieve DOPF for the small, medium, large, and IEEE 123 feeder scenarios. We are using the OEDI SI framework, as well as the example feeder, sensor, recorder, and estimator federates provided in the example repository for OEDI SI. We also provide a runner script for switching between scenarios.

algorithm↗
DOE OSTI2023

Mechanism of Hydrogen Passivation in Passivated Contact Si Solar Cells

In this abstract, we discuss the mechanism of hydrogen passivation on symmetrical n-Si/ultra-thin SiO2/polySi structures. The hydrogen was introduced from different hydrogen-containing dielectric layers (AlOx:H and SiNx:H and their stacks), as well as by forming gas anneal (FGA). The effusion of hydrogen both from the dielectric layers and in the underlying poly-Si was explored using a quadrupole mass spectrometer (QMS) and FTIR spectroscopy. We show that the strength of hydrogen bonds depend on the deposition technique as well as hydrogenation mechanism. While a PECVD SiNx:H loses hydrogen at a peak temperature of ~450 degrees C, LPCVD SiNx:H, although having less hydrogen compared to PECVD, effuses at a peak temperature of ~850 degrees C. This becomes important to maintain passivation of passivated contacts after firing of metal contacts at high temperatures. On the other hand, it has been observed that SiNx:H provides larger amount of hydrogen to poly-Si after FGA compared to FGA treated AlOx:H, which acts as a capping layer and helps in retaining the hydrogen up to higher temperatures.

hydrogen bonding configuration↗
DOE OSTI2025

Measurement of Contact Resistivity In Symmetric Polycrystalline Si/SiO x /Monocrystalline Si Test Structures Using Variable Light Illumination

While different methods exist to determine the contact resistivity in semiconductor devices, these methods are limited to measurement of the majority carrier contacts. The measurement of p‐ or n‐type contacts on n‐ or p‐type crystalline silicon, respectively, is challenging due to the blocking diode formed by the p–n junction. In this article, we address this problem for tunneling oxide passivating contacts used in high‐efficiency Si solar cells. We propose a universal method to extract contact resistivity on symmetric test structures with polycrystalline silicon on SiO x (poly‐Si/SiO x ) passivating contacts under illumination, both for p–n and high–low‐junction passivated contacts. In this method, we demonstrate that the total contact resistance of each cell grid finger to the base wafer is governed by its effective contact area, defined by the transfer length extending from both sides of the finger. Therefore, the grid contact resistance of a poly‐Si contact depends on the ratio of the doped poly‐Si sheet resistance to the tunneling contact resistivity.

14 SOLAR ENERGY↗
DOE OSTI2021

A record high average ZT over a wide temperature range in a Single-layer Sb 2 Si 2 Te 6

Conversion of waste heat into usable energy requires development of thermoelectric materials with high efficiency in a wide temperature range. Here, using first principles theory and Boltzmann transport theory, we show that the thermoelectric performance of the p-type single-layer Sb 2 Si 2 Te 6 has a high figure of merit ZT of 2.62 at 900 K and a record high average ZT of ~1.93 (corresponding the conversion efficiency of ~23.2%) in the temperature range of 300-900 K. These values are significantly higher than the recently measured average ZT of ~0.57 in the temperature range of 310–823 K [Luo et al., Joule 4, 159–175 (2020)] in layered bulk Sb 2 Si 2 Te 6 . We attribute the large enhancement of ZT in the single layer material to the increase in the thermoelectric power factor resulting from the complex Fermi surface. Our work reveals the great potential of a single-layer Sb 2 Si 2 Te 6 for wide-temperature-range thermoelectric applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

29 Si solid state MAS NMR study on leaching behaviors and chemical stability of different Mg-silicate structures for CO 2 sequestration

Silicon is one of the most earth abundant elements, and thus, the fate and reactivity of silicate materials are often important for various energy and environmental technologies including carbon sequestration, where CO 2 is captured and stored as a thermodynamically stable solid carbonate phase. Thus, understanding the structures and chemistries of different silicate phases has become an important research aim. Here in this study, the changes in the silicate structures (Q 0 –Q 4 ) of heat-treated Mg-bearing mineral (serpentine) exposed to a CO 2 -water system (carbonic acid) was investigated using 29 Si MAS NMR, XRPD and ICP-OES and the identified structures were employed to explain complex leaching behaviors of silicate materials. The 29 Si MAS NMR and XRPD analysis indicated that the heat-treated serpentine is a mixture of amorphous (Q 1 : dehydroxylate I, Q 2 : enstatite, Q 4 : silica) and crystalline (Q 0 : forsterite, Q 3 : dehydroxylate II and serpentine) phase, while natural serpentine mineral has single crystalline Q 3 silicate structure. The leaching experiments showed that both Mg and Si in the amorphous silicate structures (Q 1 : dehydroxylate I, Q 2 : enstatite) are more soluble than those in crystalline phase (Q 0 : forsterite, Q 3 : dehydroxylate II and serpentine). Therefore, tuning the silicate structure towards Q 1 and Q 2 would significantly improve carbon sequestration potential of silicate minerals, whereas silicate materials with Q 3 structure would provide great chemical stabilities in acidic conditions. The solubilities of silicate structures were in the order of Q 1 (dehydroxylate I) > Q2 (enstatite) >> Q0 (forsterite) > Q3 (dehydroxylate II) > Q 3 (serpentine) and this finding can be used to better design a wide range of energy and environmental materials and reaction systems.

25 ENERGY STORAGE↗
DOE OSTI2022

Melting and phase relations of Fe-Ni-Si determined by a multi-technique approach

Many studies have suggested silicon as a candidate light element for the cores of Earth and Mercury. However, the effect of silicon on the melting temperatures of core materials and thermal profiles of cores is poorly understood, due to disagreements among melt detection techniques, uncertainties in sample pressure evolution during heating, and sparsity of studies investigating the combined effects of nickel and silicon on the phase diagram of iron. Here, in this study we develop a multi-technique approach for measuring the high-pressure melting and solid phase relations of iron alloys and apply it to Fe 0.8 Ni 0.1 Si 0.1 (Fe-11wt%Ni-5.3wt%Si), a composition compatible with recent estimates for the cores of Earth and Mercury. This approach combines results (20-83 GPa) from two atomic-level techniques: synchrotron Mossbauer spectroscopy (SMS) and synchrotron x-ray diffraction (XRD). Melting is independently detected by the loss of the Mossbauer signal, produced exclusively by solid-bound iron nuclei, and the onset of a liquid diffuse x-ray scattering signal. The use of a burst heating and background updating method for quantifying changes in the reference background during heating facilitates the determination of liquid diffuse signal onsets and leads to strong reproducibility and excellent agreement in melting temperatures determined separately by the two techniques. XRD measurements additionally constrain the hcp-fcc phase boundary and in-situ pressure evolution of the samples during heating. We apply our updated thermal pressure model to published SMS melting data on fcc-Fe and fcc-Fe 0.9 Ni 0.1 to precisely evaluate the effect of silicon on melting temperatures. We find that the addition of 10 mol% Si to Fe 0.9 Ni 0.1 reduces melting temperatures by ~250 K at low pressures (<60 GPa) and flattens the hcp-fcc phase boundary. Extrapolating our results, we constrain the location of the hcp-fcc-liquid quasi-triple point at 147±14 GPa and 3140±90 K, which implies a melting temperature reduction of 500 K compared with Fe 0.9 Ni 0.1 . The results demonstrate the advantages of combining complementary experimental techniques in investigations of melting under extreme conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Synthesis and magnetic properties of LaFe 13- x - y M x Si y N 3 nitrides

Here, single-phase LaFe 13-x-y M x Si y N 3 compounds (M = Mn) were synthesized by subjecting intermetallic precursors to the ammonia flow at 623 K for 4 h. The nitrides derived from Si-poor (y ≤ 3) cubic intermetallics retain the NaZn 13 -type crystal structure and show considerable (~3 %) lattice expansion compared to the nitrogen-free materials. The temperatures of the magnetic ordering transitions, all of which are second order, increase by ~ 200 K as a result of nitrogenation, and all nitrides exhibit rather weak and broad magnetocaloric effects. The nitrides are stable below 750 K, but they begin to lose nitrogen above this temperature, fully decomposing above 1050 K. The nitrogenation of the tetragonal LaFe 9 Si 4 results in the decomposition of the intermetallic phase and formation of the Fe 3 N compound together with unidentified amorphous phase(s).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Phase-field simulations of intergranular fission gas bubble behavior in U 3 Si 2 nuclear fuel

U 3 Si 2 is a potential accident-tolerant fuel that shows promise due to its high thermal conductivity and higher uranium density relative to UO 2 . However, its swelling and fission gas release behavior in light water reactor (LWR) conditions is relatively unknown. To provide mechanistic insight and determine parameters for engineering-scale fuel performance modeling of pellet-form U 3 Si 2 , phase-field simulations of the growth, interconnection, and venting of intergranular fission gas bubbles were performed. The fractional coverage of the grain boundary and the fraction of bubble area that is vented were calculated as a function of time. From the simulation data, the fractional grain boundary coverage at saturation, an important parameter needed in engineering-scale modeling of swelling and fission gas release, was determined. Multiple simulations were run to determine the uncertainty in the calculated value. Finally, the effect of model assumptions and input parameters that are not well known was evaluated. Simulation results are compared to related theoretical and computational work. Based on the simulation results, a value of 0.60 for the fractional grain boundary coverage at saturation is recommended for U 3 Si 2 fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

High-temperature compressive creep tests of U 3 Si 2 with spark plasma sintering: Experiments and finite element modeling

This paper reports a systematic high-temperature creep behavior of dense U 3 Si 2 pellets using a spark plasma sintering (SPS) apparatus at elevated temperatures and pressures under vacuum conditions. The stress exponent was subsequently derived to be 3.21 at 1173 K and 2.17 at 1223 K, respectively, indicating a grain boundary sliding creep mechanism. The creep activation energy was determined to be 203.6 ± 19.0 kJ/mol, which agrees well with the literature. Finite element modeling was performed using the creep parameters fitted from the strain-time plot. Additionally, the results suggest an excellent match with the experimental data, confirming the validity of the experiments. Microstructure characterizations indicate that the main phase of the specimens after creep tests remains to be U 3 Si 2 , with a 4 μm thick layer of nano-sized particles induced from the diffusion between U 3 Si 2 and alumina disc used to avoid electric current passing through the sample. The successful conduct of creep experiments demonstrates the great potential of SPS to perform high-temperature mechanical testing of nuclear fuels under vacuum conditions. The subsequent finite element modeling exhibits excellent capabilities for accurately predicting material performance in the creep tests and provides a practical tool in evaluating nuclear fuels’ performance for a much-extended time scale.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Design of Silicide-Strengthened Nb–Si–Cr–(Mo) alloys for additive manufacturing

Three high–intermetallic volume Nb–Si–Cr–(Mo) alloys were designed using CALPHAD modeling with the goal of identifying high–specific strength, oxidation-resistant alloys that can be additively manufactured using powder bed fusion. The silicides Nb 5 Si 3 and Nb 9 Si 2 Cr3 were targeted as the primary strengthening phases, and the addition of Cr promoted the NbCr 2 phase. These alloys were cast and surface-processed with electron beam welding at different speeds to simulate additive manufacturing, and the phases and microstructures of both cast and welded regions were characterized. The weld processing was found to produce fine-grained microstructures in each alloy with fine-scale intermetallics uniformly distributed among a body-centered cubic Nb matrix. Microstructural refinement and hardness were found to increase with weld velocity; one alloy reached its highest hardness of approximately 16 GPa before the brittleness at higher velocities became detrimental. One alloy was found to be qualitatively the least brittle while also attaining a hardness of 13 GPa and was therefore identified as a good candidate for additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phosphorus replenishment to improve the contact resistivity of light-induced Al contacts on Si solar cells

A method to repair laser-induced phosphorus loss from the n-type emitter of Si solar cells during light-induced Al plating is demonstrated. The ability to add a water-reactive phosphorus compound, PCl 5 , into the Al plating bath gives a unique advantage to Al over Cu for front contacts on Si solar cells. The contact resistivity between light-induced Al and Si emitter is reduced to as low as 0.1 mΩ-cm 2 . Cyclic voltammetry performed on a plating bath composed of 81 wt% 1-ethyl-3-methylimidazolium tetrachloroaluminate, 19 wt% AlCl 3 , and 0.2 wt% PCl 5 reveals multiple reduction reactions of PCl 5 , although incomplete decomposition of PCl 5 is possible. A decrease in nucleation loop size during cyclic voltammetry is also observed suggesting that PCl 5 , while being consumed, modifies the growth mechanism during Al plating. Structural analysis confirms that the addition of PCl 5 produces an Al film which is levelized and compact. Here, a pulsed voltage profile coupled with chemical analysis verifies that phosphorus incorporation is electrolytically activated and is likely the cause for the low contact resistivity.

14 SOLAR ENERGY↗
DOE OSTI2026

Lattice-Mismatched van der Waals Epitaxy and Photoluminescence of Two-Dimensional GaxIn1-xSe Alloys on Si(111)

GaxIn1-xSe (GIS) alloys are two-dimensional (2D) layered materials with band gaps and lattice parameters of interest for many energy and electronic applications. They can be fabricated using van der Waals epitaxy, which is an emerging technique that offers unprecedented opportunities for 2D optoelectronic devices and epitaxy processes. This work has demonstrated van der Waals epitaxy of GIS alloys for the first time. Films with x compositions of 0, 0.062, 0.164, 0.680, 0.894, and 1 and tunable lattice constants were grown on Si(111) substrates, and characterized by X-ray diffraction pole figure and transmission electron microscope analysis. In spite of the lattice mismatches (InSe is 4.1% too large and GaSe is 2.8% too small), these alloys grow epitaxially, with Si(111) || GIS(001) and Si[1-10] || GIS[100] orientation. Photoluminescence was used to measure tunable band gaps in the absorber-relevant 1.3-2.0 eV range as a function of x composition and showed GIS did not degrade after capping with Se and prolonged storage. Therefore, GIS alloys exhibit a technologically advantageous combination of tunable band gap and photoluminescence with relaxed lattice parameter and rotational registry with the substrate.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Controlling Ion Coordination Structure and Diffusion Kinetics for Optimized Electrode-Electrolyte Interphases and High Performance Si Anodes

The cycling performance of batteries is largely determined by electrode-electrolyte interphase associated with the chemical and electrochemical properties of electrolyte salts and solvents. In this work, we used a localized high concentration electrolyte (LHCE) that enables high performance of Si anodes as a model system and investigated the scientific mechanism behind the optimization of electrolyte. The correlation between electrode (cathode/anode)-electrolyte interphase and ion coordination structure and diffusion kinetics were elucidated systematically. Among all the LHCEs tested, the one with 1.8M LiFSI concentration and 1:2 molar ratio of carbonate solvents and fluorinated diluents has the highest proportion of solvent-separated ion pairs and contact ion pairs and fastest ion diffusion. It enables the most stable electrode-electrolyte interphase and hence the best Si anode performance. These results reveal the fundamental mechanism behind the stability of LHCEs and provide guidance on the new electrolyte design for Si anodes and other battery systems.

Jia, Haiping↗
DOE OSTI2024

Elucidating the Role of Carbon Conductive Additive in the Processing and Electrochemical Behavior of Surface-Modified Si Anodes

In the present work, we explore the impact of conducting carbon on the processing of silicon (Si)-rich electrodes, their resulting cycling performance, and parasitic side reactions. We employed three different carbon additives, Super C45 (carbon black), Super C65 (carbon black), and TIMCAL C-NERGY KS 6L (graphite), with varying sizes and morphologies to determine how these parameters influence the structure and the electrochemical behavior of the cast electrodes. Raman mapping indicates that the improved performance achieved using C45 can be explained by the homogeneous distribution of Si and carbon, enabling the formation of continuous electrical pathways throughout the electrode. Further, this finding aligns with the results of ζ potential measurements, which indicate that C45 can maintain more stable dispersions in N-methyl-2-pyrrolidone (NMP) compared with the other carbon additives. However, electrodes with C45 as the conducting agent exhibited increased parasitic side reactions, as evidenced by the leakage current obtained from voltage hold experiments. These side reactions can have adverse effects on the calendar life of the electrode. Furthermore, the Raman maps of the electrodes reveal heterogeneities in Si and carbon distribution with lower carbon content, especially with only 2% carbon. This drastically impacts the cyclability of the electrodes, with portions of the low-carbon electrodes that remain unable to undergo cycling even at slow rates (0.2 Ah g –1 ). Additionally, we found that slower formation rates are favored in the context of parasitic side reactions, although slower formation rates can potentially create thicker passivating films that could hinder Li + -ion transport. Therefore, we emphasize the need for an intricate balance in materials selection and cycling protocol for optimal electrode processing and electrochemical behavior.

25 ENERGY STORAGE↗
DOE OSTI2021

Exceptional Radiation Absorption in a Pentagon-Based Si Allotrope

Excellent photovoltaic performance is predicted in a pentagonal covalent network of Si in a hollow structure exhibiting both thermal and dynamical stability. Consisting of a combination of sp 2 and sp 3 hybridized Si atomic orbitals, the GW0 computed band structure shows an indirect band gap near the zone edge and also a manifold of directly absorbing transitions at frequencies in the window of visible light, in distinction with conventional Si. Hydrogenation of a single sp 2 site is predicted to lead to a robust local magnetic moment. In this study, we find a low formation energy at low pressure that is compatible with other experimentally known phases, suggesting that a stable phase might be obtained.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Enhanced Interfacial Stability of Si Anodes for Li-Ion Batteries via Surface SiO2 Coating

Silicon is a promising alloying anode for lithium-ion batteries owing to its high capacity and low cost. However, its use has been hampered by mechanical failure arising from the large volume change upon cycling and by an insufficiently stable solid-electrolyte interphase (SEI). SEI formation depends on the Si surface, which is often an oxide (SiO x ). In this study we compare three different Si surfaces using Si wafers: 1.3 nm native SiO x , 1.4 nm thermally grown SiO2, and a SiOx-free surface. The oxide-free surface showed the worst electrochemical performance, never exceeding 94% Coulombic efficiency (CE). Furthermore, it also exhibited the thickest SEI and the highest overpotential for lithiation, which correlated with uninhibited electrolyte reduction and the incorporation of P-F species into the SEI. The oxide-coated surfaces performed significantly better, demonstrating a CE above 99% beyond the second cycle, low overpotential for lithiation, and a thinner and more stable SEI. The oxides lower the onset potential for electrolyte reduction, and yield an SEI with fewer P-F species. However, it was found that the CE with the native oxide surface decays from the fifth cycle onwards and correlates with a resurgence of electrolyte reduction. A 1-2 nm thermal SiO 2 coating is optimum for achieving a stable SEI that minimizes side reactions and sustains efficient cycling.

25 ENERGY STORAGE↗